@@ -57,6 +57,35 @@
"AFML", "Line In",
"AFMR", "Line In";
};
+
+ /* HS USB Port 1 RESET */
+ hsusb1_reset: hsusb1_reset_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb1_reset";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 30 0>; /* gpio_62 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
+ /* HS USB Port 1 Power */
+ hsusb1_power: hsusb1_power_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb1_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 1 0>; /* gpio_1 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
+ /* HS USB Host PHY on PORT 1 */
+ hsusb1_phy: hsusb1_phy {
+ compatible = "usb-nop-xceiv";
+ reset-supply = <&hsusb1_reset>;
+ vcc-supply = <&hsusb1_power>;
+ };
};
&omap4_pmx_core {
@@ -67,6 +96,7 @@
&mcbsp1_pins
&dss_hdmi_pins
&tpd12s015_pins
+ &hsusbb1_pins
>;
twl6040_pins: pinmux_twl6040_pins {
@@ -110,6 +140,23 @@
0x58 0x10b /* hdmi_hpd.gpio_63 INPUT PULLDOWN | MODE3 */
>;
};
+
+ hsusbb1_pins: pinmux_hsusbb1_pins {
+ pinctrl-single,pins = <
+ 0x82 0x10C /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_clk INPUT | PULLDOWN */
+ 0x84 0x4 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_stp OUTPUT */
+ 0x86 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dir INPUT | PULLDOWN */
+ 0x88 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_nxt INPUT | PULLDOWN */
+ 0x8a 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat0 INPUT | PULLDOWN */
+ 0x8c 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat1 INPUT | PULLDOWN */
+ 0x8e 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat2 INPUT | PULLDOWN */
+ 0x90 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat3 INPUT | PULLDOWN */
+ 0x92 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat4 INPUT | PULLDOWN */
+ 0x94 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat5 INPUT | PULLDOWN */
+ 0x96 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat6 INPUT | PULLDOWN */
+ 0x98 0x104 /* USBB1_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat7 INPUT | PULLDOWN */
+ >;
+ };
};
&i2c1 {
@@ -206,3 +253,11 @@
&twl_usb_comparator {
usb-supply = <&vusb>;
};
+
+&usbhshost {
+ port1-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <&hsusb1_phy>;
+};
Provide the RESET and Power regulators for the USB PHY, the USB Host port mode and the PHY device. Also provide pin multiplexer information for the USB host pins. Signed-off-by: Roger Quadros <rogerq@ti.com> --- arch/arm/boot/dts/omap4-panda.dts | 55 +++++++++++++++++++++++++++++++++++++ 1 files changed, 55 insertions(+), 0 deletions(-)