| Message ID | 1387560955-6547-5-git-send-email-balajitk@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi On Fri, Dec 20, 2013 at 6:35 PM, Balaji T K <balajitk@ti.com> wrote: > In DT case, PBAIS registers are programmed via regulator, > use regulator APIs to control PBIAS. > > Signed-off-by: Balaji T K <balajitk@ti.com> > --- > drivers/mmc/host/omap_hsmmc.c | 39 +++++++++++++++++++++++++++++++++++++++ > 1 files changed, 39 insertions(+), 0 deletions(-) > > diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c > index 342be25..0a390f8 100644 > --- a/drivers/mmc/host/omap_hsmmc.c > +++ b/drivers/mmc/host/omap_hsmmc.c > @@ -126,6 +126,10 @@ > #define OMAP_MMC_MAX_CLOCK 52000000 > #define DRIVER_NAME "omap_hsmmc" > > +#define VDD_1V8 1800000 /* 180000 uV */ > +#define VDD_3V0 3000000 /* 300000 uV */ > +#define VDD_165_195 (ffs(MMC_VDD_165_195) - 1) > + > /* > * One controller can have multiple slots, like on some omap boards using > * omap.c controller driver. Luckily this is not currently done on any known > @@ -164,6 +168,8 @@ struct omap_hsmmc_host { > */ > struct regulator *vcc; > struct regulator *vcc_aux; > + struct regulator *pbias; > + bool pbias_enabled; > int pbias_disable; > void __iomem *base; > resource_size_t mapbase; > @@ -272,6 +278,15 @@ static int omap_hsmmc_set_power(struct device *dev, int slot, int power_on, > if (mmc_slot(host).before_set_reg) > mmc_slot(host).before_set_reg(dev, slot, power_on, vdd); > > + if (host->pbias) { > + if (host->pbias_enabled == 1) { > + ret = regulator_disable(host->pbias); > + if (!ret) > + host->pbias_enabled = 0; you should return error? > + } > + regulator_set_voltage(host->pbias, VDD_3V0, VDD_3V0); > + } > + > /* > * Assume Vcc regulator is used only to power the card ... OMAP > * VDDS is used to power the pins, optionally with a transceiver to > @@ -306,9 +321,29 @@ static int omap_hsmmc_set_power(struct device *dev, int slot, int power_on, > } > } > > + if (host->pbias) { > + if (vdd <= VDD_165_195) > + ret = regulator_set_voltage(host->pbias, VDD_1V8, > + VDD_1V8); > + else > + ret = regulator_set_voltage(host->pbias, VDD_3V0, > + VDD_3V0); > + if (ret < 0) > + goto error_set_power; > + > + if (host->pbias_enabled == 0) { > + ret = regulator_enable(host->pbias); > + if (!ret) { > + host->pbias_enabled = 1; > + goto error_set_power; Is this an error condition? Do you need this flag? Mcihael > + } > + } > + } > + > if (mmc_slot(host).after_set_reg) > mmc_slot(host).after_set_reg(dev, slot, power_on, vdd); > > +error_set_power: > return ret; > } > > @@ -342,6 +377,9 @@ static int omap_hsmmc_reg_get(struct omap_hsmmc_host *host) > reg = devm_regulator_get_optional(host->dev, "vmmc_aux"); > host->vcc_aux = IS_ERR(reg) ? NULL : reg; > > + reg = devm_regulator_get_optional(host->dev, "pbias"); > + host->pbias = IS_ERR(reg) ? NULL : reg; > + > /* For eMMC do not power off when not in sleep state */ > if (mmc_slot(host).no_regulator_off_init) > return 0; > @@ -1808,6 +1846,7 @@ static int omap_hsmmc_probe(struct platform_device *pdev) > host->base = ioremap(host->mapbase, SZ_4K); > host->power_mode = MMC_POWER_OFF; > host->next_data.cookie = 1; > + host->pbias_enabled = 0; > > platform_set_drvdata(pdev, host); > > -- > 1.7.5.4 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-omap" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Friday 20 December 2013 11:45 PM, Michael Trimarchi wrote: > Hi > > On Fri, Dec 20, 2013 at 6:35 PM, Balaji T K <balajitk@ti.com> wrote: >> In DT case, PBAIS registers are programmed via regulator, >> use regulator APIs to control PBIAS. >> >> Signed-off-by: Balaji T K <balajitk@ti.com> >> --- >> drivers/mmc/host/omap_hsmmc.c | 39 +++++++++++++++++++++++++++++++++++++++ >> 1 files changed, 39 insertions(+), 0 deletions(-) >> >> diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c >> index 342be25..0a390f8 100644 >> --- a/drivers/mmc/host/omap_hsmmc.c >> +++ b/drivers/mmc/host/omap_hsmmc.c >> @@ -126,6 +126,10 @@ >> #define OMAP_MMC_MAX_CLOCK 52000000 >> #define DRIVER_NAME "omap_hsmmc" >> >> +#define VDD_1V8 1800000 /* 180000 uV */ >> +#define VDD_3V0 3000000 /* 300000 uV */ >> +#define VDD_165_195 (ffs(MMC_VDD_165_195) - 1) >> + >> /* >> * One controller can have multiple slots, like on some omap boards using >> * omap.c controller driver. Luckily this is not currently done on any known >> @@ -164,6 +168,8 @@ struct omap_hsmmc_host { >> */ >> struct regulator *vcc; >> struct regulator *vcc_aux; >> + struct regulator *pbias; >> + bool pbias_enabled; >> int pbias_disable; >> void __iomem *base; >> resource_size_t mapbase; >> @@ -272,6 +278,15 @@ static int omap_hsmmc_set_power(struct device *dev, int slot, int power_on, >> if (mmc_slot(host).before_set_reg) >> mmc_slot(host).before_set_reg(dev, slot, power_on, vdd); >> >> + if (host->pbias) { >> + if (host->pbias_enabled == 1) { >> + ret = regulator_disable(host->pbias); >> + if (!ret) >> + host->pbias_enabled = 0; > > you should return error? > >> + } >> + regulator_set_voltage(host->pbias, VDD_3V0, VDD_3V0); >> + } >> + >> /* >> * Assume Vcc regulator is used only to power the card ... OMAP >> * VDDS is used to power the pins, optionally with a transceiver to >> @@ -306,9 +321,29 @@ static int omap_hsmmc_set_power(struct device *dev, int slot, int power_on, >> } >> } >> >> + if (host->pbias) { >> + if (vdd <= VDD_165_195) >> + ret = regulator_set_voltage(host->pbias, VDD_1V8, >> + VDD_1V8); >> + else >> + ret = regulator_set_voltage(host->pbias, VDD_3V0, >> + VDD_3V0); >> + if (ret < 0) >> + goto error_set_power; >> + >> + if (host->pbias_enabled == 0) { >> + ret = regulator_enable(host->pbias); >> + if (!ret) { >> + host->pbias_enabled = 1; >> + goto error_set_power; > > Is this an error condition? Do you need this flag? > Hi, pbias_enabled flag is used to balance regulator_enable/regulator_disable, otherwise regulator might be kept enabled base on to use count. -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c index 342be25..0a390f8 100644 --- a/drivers/mmc/host/omap_hsmmc.c +++ b/drivers/mmc/host/omap_hsmmc.c @@ -126,6 +126,10 @@ #define OMAP_MMC_MAX_CLOCK 52000000 #define DRIVER_NAME "omap_hsmmc" +#define VDD_1V8 1800000 /* 180000 uV */ +#define VDD_3V0 3000000 /* 300000 uV */ +#define VDD_165_195 (ffs(MMC_VDD_165_195) - 1) + /* * One controller can have multiple slots, like on some omap boards using * omap.c controller driver. Luckily this is not currently done on any known @@ -164,6 +168,8 @@ struct omap_hsmmc_host { */ struct regulator *vcc; struct regulator *vcc_aux; + struct regulator *pbias; + bool pbias_enabled; int pbias_disable; void __iomem *base; resource_size_t mapbase; @@ -272,6 +278,15 @@ static int omap_hsmmc_set_power(struct device *dev, int slot, int power_on, if (mmc_slot(host).before_set_reg) mmc_slot(host).before_set_reg(dev, slot, power_on, vdd); + if (host->pbias) { + if (host->pbias_enabled == 1) { + ret = regulator_disable(host->pbias); + if (!ret) + host->pbias_enabled = 0; + } + regulator_set_voltage(host->pbias, VDD_3V0, VDD_3V0); + } + /* * Assume Vcc regulator is used only to power the card ... OMAP * VDDS is used to power the pins, optionally with a transceiver to @@ -306,9 +321,29 @@ static int omap_hsmmc_set_power(struct device *dev, int slot, int power_on, } } + if (host->pbias) { + if (vdd <= VDD_165_195) + ret = regulator_set_voltage(host->pbias, VDD_1V8, + VDD_1V8); + else + ret = regulator_set_voltage(host->pbias, VDD_3V0, + VDD_3V0); + if (ret < 0) + goto error_set_power; + + if (host->pbias_enabled == 0) { + ret = regulator_enable(host->pbias); + if (!ret) { + host->pbias_enabled = 1; + goto error_set_power; + } + } + } + if (mmc_slot(host).after_set_reg) mmc_slot(host).after_set_reg(dev, slot, power_on, vdd); +error_set_power: return ret; } @@ -342,6 +377,9 @@ static int omap_hsmmc_reg_get(struct omap_hsmmc_host *host) reg = devm_regulator_get_optional(host->dev, "vmmc_aux"); host->vcc_aux = IS_ERR(reg) ? NULL : reg; + reg = devm_regulator_get_optional(host->dev, "pbias"); + host->pbias = IS_ERR(reg) ? NULL : reg; + /* For eMMC do not power off when not in sleep state */ if (mmc_slot(host).no_regulator_off_init) return 0; @@ -1808,6 +1846,7 @@ static int omap_hsmmc_probe(struct platform_device *pdev) host->base = ioremap(host->mapbase, SZ_4K); host->power_mode = MMC_POWER_OFF; host->next_data.cookie = 1; + host->pbias_enabled = 0; platform_set_drvdata(pdev, host);
In DT case, PBAIS registers are programmed via regulator, use regulator APIs to control PBIAS. Signed-off-by: Balaji T K <balajitk@ti.com> --- drivers/mmc/host/omap_hsmmc.c | 39 +++++++++++++++++++++++++++++++++++++++ 1 files changed, 39 insertions(+), 0 deletions(-)