================ cut here =================================================
OMAP3EVM uses ISP1504 phy which doesn't require any programming and
thus has to use NOP otg transceiver.
Cleanups being done:
- Remove unwanted code in usb-musb.c file
- Register NOP in OMAP3EVM board file using
usb_nop_xceiv_register().
- Select NOP_USB_XCEIV for OMAP3EVM boards.
- Don't enable TWL4030_USB in omap3_evm_defconfig
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Eino-Ville Talvala <talvala@stanford.edu>
---
Resubmitting with below changes.
- Refreshed against linus tree
- Combining recent patch from Eino-Ville Talvala on
"Removing TWL4030_USB from omap3_evm_defconfig"
- Register nop under #ifdef to avoid compilation warning when
USB itself it not selected in OMAP3EVM build.
arch/arm/configs/omap3_evm_defconfig | 2 +-
arch/arm/mach-omap2/board-omap3evm.c | 5 +++++
arch/arm/mach-omap2/usb-musb.c | 21 ---------------------
drivers/usb/musb/Kconfig | 1 +
4 files changed, 7 insertions(+), 22 deletions(-)
@@ -1107,7 +1107,7 @@ CONFIG_USB_ZERO=m
CONFIG_USB_OTG_UTILS=y
# CONFIG_USB_GPIO_VBUS is not set
# CONFIG_ISP1301_OMAP is not set
-CONFIG_TWL4030_USB=y
+# CONFIG_TWL4030_USB is not set
# CONFIG_NOP_USB_XCEIV is not set
CONFIG_MMC=y
# CONFIG_MMC_DEBUG is not set
@@ -25,6 +25,7 @@
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/i2c/twl4030.h>
+#include <linux/usb/otg.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
@@ -307,6 +308,10 @@ static void __init omap3_evm_init(void)
ARRAY_SIZE(omap3evm_spi_board_info));
omap_serial_init();
+#ifdef CONFIG_NOP_USB_XCEIV
+ /* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
+ usb_nop_xceiv_register();
+#endif
usb_musb_init();
ads7846_dev_init();
}
@@ -155,20 +155,6 @@ static struct platform_device musb_device = {
.resource = musb_resources,
};
-#ifdef CONFIG_NOP_USB_XCEIV
-static u64 nop_xceiv_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device nop_xceiv_device = {
- .name = "nop_usb_xceiv",
- .id = -1,
- .dev = {
- .dma_mask = &nop_xceiv_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = NULL,
- },
-};
-#endif
-
void __init usb_musb_init(void)
{
if (cpu_is_omap243x())
@@ -183,13 +169,6 @@ void __init usb_musb_init(void)
*/
musb_plat.clock = "ick";
-#ifdef CONFIG_NOP_USB_XCEIV
- if (platform_device_register(&nop_xceiv_device) < 0) {
- printk(KERN_ERR "Unable to register NOP-XCEIV device\n");
- return;
- }
-#endif
-
if (platform_device_register(&musb_device) < 0) {
printk(KERN_ERR "Unable to register HS-USB (MUSB) device\n");
return;
@@ -12,6 +12,7 @@ config USB_MUSB_HDRC
depends on !SUPERH
select NOP_USB_XCEIV if ARCH_DAVINCI
select TWL4030_USB if MACH_OMAP_3430SDP
+ select NOP_USB_XCEIV if MACH_OMAP3EVM
select USB_OTG_UTILS
tristate 'Inventra Highspeed Dual Role Controller (TI, ADI, ...)'
help