@@ -3,13 +3,12 @@
*
* Omap3 specific functions that need to be run in internal SRAM
*
- * (C) Copyright 2007
- * Texas Instruments Inc.
- * Rajendra Nayak <rnayak@ti.com>
+ * Copyright (C) 2004, 2007, 2008 Texas Instruments, Inc.
+ * Copyright (C) 2008 Nokia Corporation
*
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
+ * Rajendra Nayak <rnayak@ti.com>
* Richard Woodruff <r-woodruff2@ti.com>
+ * Paul Walmsley
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
@@ -38,13 +37,16 @@
.text
/*
- * Change frequency of core dpll
- * r0 = sdrc_rfr_ctrl r1 = sdrc_actim_ctrla r2 = sdrc_actim_ctrlb r3 = M2
- * r4 = Unlock SDRC DLL? (1 = yes, 0 = no) -- only unlock DLL for
+ * omap3_sram_configure_core_dpll - change DPLL3 M2 divider
+ * r0 = new SDRC_RFR_CTRL register contents
+ * r1 = new SDRC_ACTIM_CTRLA register contents
+ * r2 = new SDRC_ACTIM_CTRLB register contents
+ * r3 = new M2 divider setting (only 1 and 2 supported right now)
+ * r4 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for
* SDRC rates < 83MHz
* r5 = number of MPU cycles to wait for SDRC to stabilize after
* reprogramming the SDRC when switching to a slower MPU speed
- * r6 = SDRC_MR_0 register value
+ * r6 = new SDRC_MR_0 register value
*
*/
ENTRY(omap3_sram_configure_core_dpll)
@@ -53,22 +55,22 @@ ENTRY(omap3_sram_configure_core_dpll)
ldr r5, [sp, #56] @ load extra args from the stack
ldr r6, [sp, #60] @ load extra args from the stack
dsb @ flush buffered writes to interconnect
- cmp r3, #0x2
- blne configure_sdrc
- cmp r4, #0x1
+ cmp r3, #0x2 @ if increasing SDRC clk rate,
+ blne configure_sdrc @ program the SDRC regs early (for RFR)
+ cmp r4, #0x1 @ set the intended DLL state
bleq unlock_dll
blne lock_dll
- bl sdram_in_selfrefresh @ put the SDRAM in self refresh
- bl configure_core_dpll
- bl enable_sdrc
- cmp r4, #0x1
+ bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC
+ bl configure_core_dpll @ change the DPLL3 M2 divider
+ bl enable_sdrc @ take SDRC out of idle
+ cmp r4, #0x1 @ wait for DLL status to change
bleq wait_dll_unlock
blne wait_dll_lock
- cmp r3, #0x1
- beq return_to_sdram
- bl configure_sdrc
- mov r12, r5 @ if slowing, wait for SDRC to stabilize
- bl wait_clk_stable
+ cmp r3, #0x1 @ if increasing SDRC clk rate,
+ beq return_to_sdram @ return to SDRAM code, otherwise,
+ bl configure_sdrc @ reprogram SDRC regs now
+ mov r12, r5
+ bl wait_clk_stable @ wait for SDRC to stabilize
return_to_sdram:
isb @ prevent speculative exec past here
mov r0, #0 @ return value
@@ -93,6 +95,7 @@ sdram_in_selfrefresh:
bic r12, r12, #0x4 @ clear PWDENA
str r12, [r11] @ write back to SDRC_POWER register
ldr r12, [r11] @ posted-write barrier for SDRC
+idle_sdrc:
ldr r11, omap3_cm_iclken1_core @ read the CM_ICLKEN1_CORE reg
ldr r12, [r11]
bic r12, r12, #0x2 @ disable iclk bit for SDRC
Clean up comments and copyrights on the CORE DPLL3 M2 divider change code. Signed-off-by: Paul Walmsley <paul@pwsan.com> --- arch/arm/mach-omap2/sram34xx.S | 45 +++++++++++++++++++++------------------- 1 files changed, 24 insertions(+), 21 deletions(-) -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html