@@ -73,6 +73,10 @@ config MACH_OMAP_3430SDP
bool "OMAP 3430 SDP board"
depends on ARCH_OMAP3 && ARCH_OMAP34XX
+config MACH_NOKIA_N8X0
+ bool "Nokia N800/N810"
+ depends on ARCH_OMAP2420
+
config MACH_NOKIA_RX51
bool "Nokia RX-51 board"
depends on ARCH_OMAP3 && ARCH_OMAP34XX
@@ -62,7 +62,7 @@ obj-$(CONFIG_MACH_OMAP3_PANDORA) += board-omap3pandora.o \
mmc-twl4030.o
obj-$(CONFIG_MACH_OMAP_3430SDP) += board-3430sdp.o \
mmc-twl4030.o
-
+obj-$(CONFIG_MACH_NOKIA_N8X0) += board-n8x0.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o \
board-rx51-peripherals.o \
mmc-twl4030.o
new file mode 100644
@@ -0,0 +1,307 @@
+/*
+ * linux/arch/arm/mach-omap2/board-n8x0.c
+ *
+ * Copyright (C) 2005-2007 Nokia Corporation
+ * Author: Juha Yrjola <juha.yrjola@nokia.com>
+ *
+ * Modified from mach-omap2/board-generic.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/stddef.h>
+#include <linux/spi/spi.h>
+#include <linux/usb/musb.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach-types.h>
+
+#include <mach/board.h>
+#include <mach/common.h>
+#include <mach/gpio.h>
+#include <mach/io.h>
+#include <mach/irqs.h>
+#include <mach/mcspi.h>
+#include <mach/onenand.h>
+#include <mach/serial.h>
+
+#define TUSB_ASYNC_CS 1
+#define TUSB_SYNC_CS 4
+#define GPIO_TUSB_INT 58
+#define GPIO_TUSB_ENABLE 0
+
+#if defined(CONFIG_USB_MUSB_OTG)
+#define BOARD_MODE MUSB_OTG
+#elif defined(CONFIG_USB_MUSB_PERIPHERAL)
+#define BOARD_MODE MUSB_PERIPHERAL
+#else /* defined(CONFIG_USB_MUSB_HOST) */
+#define BOARD_MODE MUSB_HOST
+#endif
+
+/*
+ * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and
+ * 1.5 V voltage regulators of PM companion chip. Companion chip will then
+ * provide then PGOOD signal to TUSB6010 which will release it from reset.
+ */
+static int tusb_set_power(int state)
+{
+ int i, retval = 0;
+
+ if (state) {
+ gpio_set_value(GPIO_TUSB_ENABLE, 1);
+ msleep(1);
+
+ /* Wait until TUSB6010 pulls INT pin down */
+ i = 100;
+ while (i && gpio_get_value(GPIO_TUSB_INT)) {
+ msleep(1);
+ i--;
+ }
+
+ if (!i) {
+ printk(KERN_ERR "tusb: powerup failed\n");
+ retval = -ENODEV;
+ }
+ } else {
+ gpio_set_value(GPIO_TUSB_ENABLE, 0);
+ msleep(10);
+ }
+
+ return retval;
+}
+
+static int osc_ck_on;
+
+static int tusb_set_clock(struct clk *osc_ck, int state)
+{
+ if (state) {
+ if (osc_ck_on > 0)
+ return -ENODEV;
+
+ clk_enable(osc_ck);
+ osc_ck_on = 1;
+ } else {
+ if (osc_ck_on == 0)
+ return -ENODEV;
+
+ clk_disable(osc_ck);
+ osc_ck_on = 0;
+ }
+
+ return 0;
+}
+
+static struct musb_hdrc_eps_bits musb_eps[] = {
+ { "ep1_tx", 5, },
+ { "ep1_rx", 5, },
+ { "ep2_tx", 5, },
+ { "ep2_rx", 5, },
+ { "ep3_tx", 3, },
+ { "ep3_rx", 3, },
+ { "ep4_tx", 3, },
+ { "ep4_rx", 3, },
+ { "ep5_tx", 2, },
+ { "ep5_rx", 2, },
+ { "ep6_tx", 2, },
+ { "ep6_rx", 2, },
+ { "ep7_tx", 2, },
+ { "ep7_rx", 2, },
+ { "ep8_tx", 2, },
+ { "ep8_rx", 2, },
+ { "ep9_tx", 2, },
+ { "ep9_rx", 2, },
+ { "ep10_tx", 2, },
+ { "ep10_rx", 2, },
+ { "ep11_tx", 2, },
+ { "ep11_rx", 2, },
+ { "ep12_tx", 2, },
+ { "ep12_rx", 2, },
+ { "ep13_tx", 2, },
+ { "ep13_rx", 2, },
+ { "ep14_tx", 2, },
+ { "ep14_rx", 2, },
+ { "ep15_tx", 2, },
+ { "ep15_rx", 2, },
+};
+
+static struct musb_hdrc_config musb_config = {
+ .multipoint = 1,
+ .dyn_fifo = 1,
+ .soft_con = 1,
+ .dma = 1,
+ .num_eps = 16,
+ .dma_channels = 7,
+ .ram_bits = 12,
+ .eps_bits = musb_eps,
+};
+
+static struct musb_hdrc_platform_data tusb_data = {
+ .mode = BOARD_MODE,
+ .set_power = tusb_set_power,
+ .set_clock = tusb_set_clock,
+ .min_power = 25, /* x2 = 50 mA drawn from VBUS as peripheral */
+ .power = 100, /* Max 100 mA VBUS for host mode */
+ .clock = "osc_ck",
+ .config = &musb_config,
+};
+
+static void __init n8x0_usb_init(void)
+{
+ int ret = 0;
+ static char announce[] __initdata = KERN_INFO "TUSB 6010\n";
+
+ /* PM companion chip power control pin */
+ ret = gpio_request(GPIO_TUSB_ENABLE, "TUSB6010 enable");
+ if (ret != 0) {
+ printk(KERN_ERR "Could not get TUSB power GPIO%i\n",
+ GPIO_TUSB_ENABLE);
+ return;
+ }
+ gpio_direction_output(GPIO_TUSB_ENABLE, 0);
+
+ tusb_set_power(0);
+
+ ret = tusb6010_setup_interface(&tusb_data, TUSB6010_REFCLK_19, 2,
+ TUSB_ASYNC_CS, TUSB_SYNC_CS,
+ GPIO_TUSB_INT, 0x3f);
+ if (ret != 0)
+ goto err;
+
+ printk(announce);
+
+ return;
+
+err:
+ gpio_free(GPIO_TUSB_ENABLE);
+}
+
+static struct omap2_mcspi_device_config p54spi_mcspi_config = {
+ .turbo_mode = 0,
+ .single_channel = 1,
+};
+
+static struct spi_board_info n800_spi_board_info[] __initdata = {
+ {
+ .modalias = "p54spi",
+ .bus_num = 2,
+ .chip_select = 0,
+ .max_speed_hz = 48000000,
+ .controller_data = &p54spi_mcspi_config,
+ },
+};
+
+#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
+ defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
+
+static struct mtd_partition onenand_partitions[] = {
+ {
+ .name = "bootloader",
+ .offset = 0,
+ .size = 0x20000,
+ .mask_flags = MTD_WRITEABLE, /* Force read-only */
+ },
+ {
+ .name = "config",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 0x60000,
+ },
+ {
+ .name = "kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 0x200000,
+ },
+ {
+ .name = "initfs",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 0x400000,
+ },
+ {
+ .name = "rootfs",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct omap_onenand_platform_data board_onenand_data = {
+ .cs = 0,
+ .gpio_irq = 26,
+ .parts = onenand_partitions,
+ .nr_parts = ARRAY_SIZE(onenand_partitions),
+ .flags = ONENAND_SYNC_READ,
+};
+
+static void __init n8x0_onenand_init(void)
+{
+ gpmc_onenand_init(&board_onenand_data);
+}
+
+#else
+
+static void __init n8x0_onenand_init(void) {}
+
+#endif
+
+/* FIXME: n810 needs UART1 */
+static struct omap_uart_platform_data n8x0_uart_config __initdata = {
+ .enabled_uarts = (1 << 2),
+};
+
+static void __init n8x0_map_io(void)
+{
+ omap2_set_globals_242x();
+ omap2_map_common_io();
+}
+
+static void __init n8x0_init_irq(void)
+{
+ omap2_init_common_hw(NULL);
+ omap_init_irq();
+ omap_gpio_init();
+}
+
+static void __init n8x0_init_machine(void)
+{
+ /* FIXME: add n810 spi devices */
+ spi_register_board_info(n800_spi_board_info,
+ ARRAY_SIZE(n800_spi_board_info));
+
+ omap_serial_init(&n8x0_uart_config);
+ n8x0_onenand_init();
+
+ n8x0_usb_init();
+}
+
+MACHINE_START(NOKIA_N800, "Nokia N800")
+ .phys_io = 0x48000000,
+ .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
+ .boot_params = 0x80000100,
+ .map_io = n8x0_map_io,
+ .init_irq = n8x0_init_irq,
+ .init_machine = n8x0_init_machine,
+ .timer = &omap_timer,
+MACHINE_END
+
+MACHINE_START(NOKIA_N810, "Nokia N810")
+ .phys_io = 0x48000000,
+ .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
+ .boot_params = 0x80000100,
+ .map_io = n8x0_map_io,
+ .init_irq = n8x0_init_irq,
+ .init_machine = n8x0_init_machine,
+ .timer = &omap_timer,
+MACHINE_END
+
+MACHINE_START(NOKIA_N810_WIMAX, "Nokia N810 WiMAX")
+ .phys_io = 0x48000000,
+ .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
+ .boot_params = 0x80000100,
+ .map_io = n8x0_map_io,
+ .init_irq = n8x0_init_irq,
+ .init_machine = n8x0_init_machine,
+ .timer = &omap_timer,
+MACHINE_END
Signed-off-by: Kalle Valo <kalle.valo@iki.fi> --- arch/arm/mach-omap2/Kconfig | 4 arch/arm/mach-omap2/Makefile | 2 arch/arm/mach-omap2/board-n8x0.c | 307 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 312 insertions(+), 1 deletions(-) create mode 100644 arch/arm/mach-omap2/board-n8x0.c -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html