@@ -630,6 +630,28 @@ static struct gpiod_hog ams_delta_gpio_hogs[] = {
{},
};
+static struct plat_serial8250_port ams_delta_modem_ports[];
+
+/*
+ * Obtain MODEM IRQ GPIO descriptor using its hardware pin
+ * number and assign related IRQ number to the MODEM port.
+ * Keep the GPIO descriptor open so nobody steps in.
+ */
+static void __init modem_assign_irq(struct gpio_chip *chip)
+{
+ struct gpio_desc *gpiod;
+
+ gpiod = gpiochip_request_own_desc(chip, AMS_DELTA_GPIO_PIN_MODEM_IRQ,
+ "modem_irq");
+ if (IS_ERR(gpiod)) {
+ pr_err("%s: modem IRQ GPIO request failed (%ld)\n", __func__,
+ PTR_ERR(gpiod));
+ } else {
+ gpiod_direction_input(gpiod);
+ ams_delta_modem_ports[0].irq = gpiod_to_irq(gpiod);
+ }
+}
+
/*
* The purpose of this function is to take care of proper initialization of
* devices and data structures which depend on GPIO lines provided by OMAP GPIO
@@ -649,7 +671,13 @@ static void __init omap_gpio_deps_init(void)
return;
}
+ /*
+ * Start with FIQ initialization as it may have to request
+ * and release successfully each OMAP GPIO pin in turn.
+ */
ams_delta_init_fiq(chip, &ams_delta_serio_device);
+
+ modem_assign_irq(chip);
}
static void __init ams_delta_init(void)
@@ -844,20 +872,18 @@ static int __init modem_nreset_init(void)
}
+/*
+ * This function expects MODEM IRQ number already assigned to the port
+ * and fails if it's not.
+ */
static int __init ams_delta_modem_init(void)
{
int err;
- omap_cfg_reg(M14_1510_GPIO2);
- ams_delta_modem_ports[0].irq =
- gpio_to_irq(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
+ if (ams_delta_modem_ports[0].irq < 0)
+ return ams_delta_modem_ports[0].irq;
- err = gpio_request(AMS_DELTA_GPIO_PIN_MODEM_IRQ, "modem");
- if (err) {
- pr_err("Couldn't request gpio pin for modem\n");
- return err;
- }
- gpio_direction_input(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
+ omap_cfg_reg(M14_1510_GPIO2);
/* Initialize the modem_nreset regulator consumer before use */
modem_priv.regulator = ERR_PTR(-ENODEV);
@@ -866,8 +892,6 @@ static int __init ams_delta_modem_init(void)
AMS_DELTA_LATCH2_MODEM_CODEC);
err = platform_device_register(&ams_delta_modem_device);
- if (err)
- gpio_free(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
return err;
}
In ams_delta_modem_init(), replace request for hardcoded GPIO and assignment of related IRQ number to MODEM platform data with a check for that number having already been assigned. Then, from init_machine, request MODEM IRQ GPIO descriptor by its GPIO chip hardware pin number and assign related IRQ to the MODEM. Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> --- arch/arm/mach-omap1/board-ams-delta.c | 46 ++++++++++++++++++++++++++--------- 1 file changed, 35 insertions(+), 11 deletions(-)