@@ -290,6 +290,23 @@ static void __init innovator_init_smc91x(void)
}
#ifdef CONFIG_ARCH_OMAP15XX
+/*
+ * Board specific gang-switched transceiver power on/off.
+ */
+static int innovator_omap_ohci_transceiver_power(int on)
+{
+ if (on)
+ __raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
+ | ((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
+ INNOVATOR_FPGA_CAM_USB_CONTROL);
+ else
+ __raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
+ & ~((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
+ INNOVATOR_FPGA_CAM_USB_CONTROL);
+
+ return 0;
+}
+
static struct omap_usb_config innovator1510_usb_config __initdata = {
/* for bundled non-standard host and peripheral cables */
.hmc_mode = 4,
@@ -300,6 +317,8 @@ static struct omap_usb_config innovator1510_usb_config __initdata = {
.register_dev = 1,
.pins[0] = 2,
+
+ .transceiver_power = innovator_omap_ohci_transceiver_power,
};
static const struct omap_lcd_config innovator1510_lcd_config __initconst = {
@@ -278,6 +278,23 @@ static void __init osk_init_cf(void)
irq_set_irq_type(gpio_to_irq(62), IRQ_TYPE_EDGE_FALLING);
}
+/*
+ * Board specific gang-switched transceiver power on/off.
+ * NOTE: OSK supplies power from DC, not battery.
+ */
+static int osk_omap_ohci_transceiver_power(int on)
+{
+ if (!IS_BUILTIN(CONFIG_TPS65010))
+ return -ENXIO;
+
+ if (on)
+ tps65010_set_gpio_out_value(GPIO1, LOW);
+ else
+ tps65010_set_gpio_out_value(GPIO1, HIGH);
+
+ return 0;
+}
+
static struct omap_usb_config osk_usb_config __initdata = {
/* has usb host connector (A) ... for development it can also
* be used, with a NONSTANDARD gender-bending cable/dongle, as
@@ -292,6 +309,8 @@ static struct omap_usb_config osk_usb_config __initdata = {
.rwc = 1,
#endif
.pins[0] = 2,
+
+ .transceiver_power = osk_omap_ohci_transceiver_power,
};
#ifdef CONFIG_OMAP_OSK_MISTRAL
@@ -77,31 +77,6 @@ static void omap_ohci_clock_power(int on)
}
}
-/*
- * Board specific gang-switched transceiver power on/off.
- * NOTE: OSK supplies power from DC, not battery.
- */
-static int omap_ohci_transceiver_power(int on)
-{
- if (on) {
- if (machine_is_omap_innovator() && cpu_is_omap1510())
- __raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
- | ((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
- INNOVATOR_FPGA_CAM_USB_CONTROL);
- else if (machine_is_omap_osk())
- tps65010_set_gpio_out_value(GPIO1, LOW);
- } else {
- if (machine_is_omap_innovator() && cpu_is_omap1510())
- __raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
- & ~((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
- INNOVATOR_FPGA_CAM_USB_CONTROL);
- else if (machine_is_omap_osk())
- tps65010_set_gpio_out_value(GPIO1, HIGH);
- }
-
- return 0;
-}
-
#ifdef CONFIG_USB_OTG
static void start_hnp(struct ohci_hcd *ohci)
@@ -213,7 +188,8 @@ static int ohci_omap_reset(struct usb_hcd *hcd)
}
/* FIXME hub_wq hub requests should manage power switching */
- omap_ohci_transceiver_power(1);
+ if (config->transceiver_power)
+ config->transceiver_power(1);
/* board init will have already handled HMC and mux setup.
* any external transceiver should already be initialized
@@ -50,6 +50,8 @@ struct omap_usb_config {
int (*ocpi_enable)(void);
void (*lb_reset)(void);
+
+ int (*transceiver_power)(int on);
};
#endif /* __LINUX_USB_OMAP1_H */
Two boards require a a special handler to control their transceiver power. Move the corresponding code into the board files and out of the common code. The osk board already has a dependency on TPS65010, this adds another one, with the same hack to get it to compile with CONFIG_TPS65010=m. Signed-off-by: Arnd Bergmann <arnd@arndb.de> --- arch/arm/mach-omap1/board-innovator.c | 19 +++++++++++++++++ arch/arm/mach-omap1/board-osk.c | 19 +++++++++++++++++ drivers/usb/host/ohci-omap.c | 28 ++----------------------- include/linux/platform_data/usb-omap1.h | 2 ++ 4 files changed, 42 insertions(+), 26 deletions(-)