diff mbox series

[3/4] thermal: ti-soc-thermal: Simplify polling with iopoll

Message ID 20210205134534.49200-4-tony@atomide.com (mailing list archive)
State New, archived
Headers show
Series Thermal fixes for omaps for single mode read | expand

Commit Message

Tony Lindgren Feb. 5, 2021, 1:45 p.m. UTC
We can use iopoll for checking the EOCZ (end of conversion) bit. And with
this we now also want to handle the timeout errors properly.

For omap3, we need about 1.2ms for the single mode sampling to wait for
EOCZ down, so let's use 1.5ms timeout there. Waiting for sampling to start
is faster and we can use 1ms timeout.

Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 drivers/thermal/ti-soc-thermal/ti-bandgap.c | 30 ++++++++++-----------
 1 file changed, 14 insertions(+), 16 deletions(-)

Comments

Adam Ford Feb. 6, 2021, 1:02 p.m. UTC | #1
On Fri, Feb 5, 2021 at 7:45 AM Tony Lindgren <tony@atomide.com> wrote:
>
> We can use iopoll for checking the EOCZ (end of conversion) bit. And with
> this we now also want to handle the timeout errors properly.
>
> For omap3, we need about 1.2ms for the single mode sampling to wait for
> EOCZ down, so let's use 1.5ms timeout there. Waiting for sampling to start
> is faster and we can use 1ms timeout.
>
> Cc: Adam Ford <aford173@gmail.com>
> Cc: Carl Philipp Klemm <philipp@uvos.xyz>
> Cc: Eduardo Valentin <edubezval@gmail.com>
> Cc: H. Nikolaus Schaller <hns@goldelico.com>
> Cc: Merlijn Wajer <merlijn@wizzup.org>
> Cc: Pavel Machek <pavel@ucw.cz>
> Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
> Cc: Sebastian Reichel <sre@kernel.org>
> Signed-off-by: Tony Lindgren <tony@atomide.com>

For the series,

Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit

> ---
>  drivers/thermal/ti-soc-thermal/ti-bandgap.c | 30 ++++++++++-----------
>  1 file changed, 14 insertions(+), 16 deletions(-)
>
> diff --git a/drivers/thermal/ti-soc-thermal/ti-bandgap.c b/drivers/thermal/ti-soc-thermal/ti-bandgap.c
> --- a/drivers/thermal/ti-soc-thermal/ti-bandgap.c
> +++ b/drivers/thermal/ti-soc-thermal/ti-bandgap.c
> @@ -15,7 +15,6 @@
>  #include <linux/kernel.h>
>  #include <linux/interrupt.h>
>  #include <linux/clk.h>
> -#include <linux/delay.h>
>  #include <linux/gpio/consumer.h>
>  #include <linux/platform_device.h>
>  #include <linux/err.h>
> @@ -27,6 +26,7 @@
>  #include <linux/of_platform.h>
>  #include <linux/of_irq.h>
>  #include <linux/io.h>
> +#include <linux/iopoll.h>
>  #include <linux/cpu_pm.h>
>  #include <linux/device.h>
>  #include <linux/pm_runtime.h>
> @@ -604,7 +604,9 @@ static int
>  ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id)
>  {
>         struct temp_sensor_registers *tsr = bgp->conf->sensors[id].registers;
> -       u32 counter;
> +       void __iomem *temp_sensor_ctrl = bgp->base + tsr->temp_sensor_ctrl;
> +       int error;
> +       u32 val;
>
>         /* Select continuous or single conversion mode */
>         if (TI_BANDGAP_HAS(bgp, MODE_CONFIG)) {
> @@ -619,26 +621,22 @@ ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id)
>                 RMW_BITS(bgp, id, temp_sensor_ctrl, bgap_soc_mask, 1);
>
>                 /* Wait for EOCZ going up */
> -               counter = 1000;
> -               while (--counter) {
> -                       if (ti_bandgap_readl(bgp, tsr->temp_sensor_ctrl) &
> -                           tsr->bgap_eocz_mask)
> -                               break;
> -                       udelay(1);
> -               }
> +               error = readl_poll_timeout_atomic(temp_sensor_ctrl, val,
> +                                                 val & tsr->bgap_eocz_mask,
> +                                                 1, 1000);
> +               if (error)
> +                       dev_warn(bgp->dev, "eocz timed out waiting high\n");
>
>                 /* Clear Start of Conversion if available */
>                 RMW_BITS(bgp, id, temp_sensor_ctrl, bgap_soc_mask, 0);
>         }
>
>         /* Wait for EOCZ going down, always needed even if no bgap_soc_mask */
> -       counter = 1000;
> -       while (--counter) {
> -               if (!(ti_bandgap_readl(bgp, tsr->temp_sensor_ctrl) &
> -                     tsr->bgap_eocz_mask))
> -                       break;
> -               udelay(1);
> -       }
> +       error = readl_poll_timeout_atomic(temp_sensor_ctrl, val,
> +                                         !(val & tsr->bgap_eocz_mask),
> +                                         1, 1500);
> +       if (error)
> +               dev_warn(bgp->dev, "eocz timed out waiting low\n");
>
>         return 0;
>  }
> --
> 2.30.0
diff mbox series

Patch

diff --git a/drivers/thermal/ti-soc-thermal/ti-bandgap.c b/drivers/thermal/ti-soc-thermal/ti-bandgap.c
--- a/drivers/thermal/ti-soc-thermal/ti-bandgap.c
+++ b/drivers/thermal/ti-soc-thermal/ti-bandgap.c
@@ -15,7 +15,6 @@ 
 #include <linux/kernel.h>
 #include <linux/interrupt.h>
 #include <linux/clk.h>
-#include <linux/delay.h>
 #include <linux/gpio/consumer.h>
 #include <linux/platform_device.h>
 #include <linux/err.h>
@@ -27,6 +26,7 @@ 
 #include <linux/of_platform.h>
 #include <linux/of_irq.h>
 #include <linux/io.h>
+#include <linux/iopoll.h>
 #include <linux/cpu_pm.h>
 #include <linux/device.h>
 #include <linux/pm_runtime.h>
@@ -604,7 +604,9 @@  static int
 ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id)
 {
 	struct temp_sensor_registers *tsr = bgp->conf->sensors[id].registers;
-	u32 counter;
+	void __iomem *temp_sensor_ctrl = bgp->base + tsr->temp_sensor_ctrl;
+	int error;
+	u32 val;
 
 	/* Select continuous or single conversion mode */
 	if (TI_BANDGAP_HAS(bgp, MODE_CONFIG)) {
@@ -619,26 +621,22 @@  ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id)
 		RMW_BITS(bgp, id, temp_sensor_ctrl, bgap_soc_mask, 1);
 
 		/* Wait for EOCZ going up */
-		counter = 1000;
-		while (--counter) {
-			if (ti_bandgap_readl(bgp, tsr->temp_sensor_ctrl) &
-			    tsr->bgap_eocz_mask)
-				break;
-			udelay(1);
-		}
+		error = readl_poll_timeout_atomic(temp_sensor_ctrl, val,
+						  val & tsr->bgap_eocz_mask,
+						  1, 1000);
+		if (error)
+			dev_warn(bgp->dev, "eocz timed out waiting high\n");
 
 		/* Clear Start of Conversion if available */
 		RMW_BITS(bgp, id, temp_sensor_ctrl, bgap_soc_mask, 0);
 	}
 
 	/* Wait for EOCZ going down, always needed even if no bgap_soc_mask */
-	counter = 1000;
-	while (--counter) {
-		if (!(ti_bandgap_readl(bgp, tsr->temp_sensor_ctrl) &
-		      tsr->bgap_eocz_mask))
-			break;
-		udelay(1);
-	}
+	error = readl_poll_timeout_atomic(temp_sensor_ctrl, val,
+					  !(val & tsr->bgap_eocz_mask),
+					  1, 1500);
+	if (error)
+		dev_warn(bgp->dev, "eocz timed out waiting low\n");
 
 	return 0;
 }