Message ID | 559D0BA4.9000000@ti.com (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
On 07/08/2015 02:38 PM, Roger Quadros wrote: > From: "J.D. Schroeder" <jay.schroeder@garmin.com> > > The previous change 3973c526ae9c (net: can: c_can: Disable pins when CAN interface > is down) causes a slight glitch on the pinctrl settings when used. Since > commit ab78029 (drivers/pinctrl: grab default handles from device core), > the device core will automatically set the default pins. This causes > the pins to be momentarily set to the default and then to the sleep > state in register_c_can_dev(). By adding an optional "enable" state, > boards can set the default pin state to be disabled and avoid the > glitch when the switch from default to sleep first occurs. If the > "enable" state is not available c_can_pinctrl_select_state() falls > back to using the "default" pinctrl state. > > [Roger Q] - Forward port to v4.2 and use pinctrl_get_select(). > > Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com> > Signed-off-by: Roger Quadros <rogerq@ti.com> > --- > drivers/net/can/c_can/c_can.c | 10 ++++++++-- > 1 file changed, 8 insertions(+), 2 deletions(-) > > diff --git a/drivers/net/can/c_can/c_can.c b/drivers/net/can/c_can/c_can.c > index 041525d..5d214d1 100644 > --- a/drivers/net/can/c_can/c_can.c > +++ b/drivers/net/can/c_can/c_can.c > @@ -592,6 +592,7 @@ static int c_can_start(struct net_device *dev) > { > struct c_can_priv *priv = netdev_priv(dev); > int err; > + struct pinctrl *p; > > /* basic c_can configuration */ > err = c_can_chip_config(dev); > @@ -604,8 +605,13 @@ static int c_can_start(struct net_device *dev) > > priv->can.state = CAN_STATE_ERROR_ACTIVE; > > - /* activate pins */ > - pinctrl_pm_select_default_state(dev->dev.parent); > + /* Attempt to use "active" if available else use "default" */ > + p = pinctrl_get_select(priv->device, "active"); > + if (!IS_ERR(p)) > + pinctrl_put(p); > + else > + pinctrl_pm_select_default_state(priv->device); > + Thanks. This part looks good to me now. > return 0; > } > >
On 07/09/2015 12:58 PM, Grygorii Strashko wrote: > On 07/08/2015 02:38 PM, Roger Quadros wrote: >> From: "J.D. Schroeder" <jay.schroeder@garmin.com> >> >> The previous change 3973c526ae9c (net: can: c_can: Disable pins when CAN interface >> is down) causes a slight glitch on the pinctrl settings when used. Since >> commit ab78029 (drivers/pinctrl: grab default handles from device core), >> the device core will automatically set the default pins. This causes >> the pins to be momentarily set to the default and then to the sleep >> state in register_c_can_dev(). By adding an optional "enable" state, >> boards can set the default pin state to be disabled and avoid the >> glitch when the switch from default to sleep first occurs. If the >> "enable" state is not available c_can_pinctrl_select_state() falls >> back to using the "default" pinctrl state. >> >> [Roger Q] - Forward port to v4.2 and use pinctrl_get_select(). >> >> Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com> >> Signed-off-by: Roger Quadros <rogerq@ti.com> >> --- >> drivers/net/can/c_can/c_can.c | 10 ++++++++-- >> 1 file changed, 8 insertions(+), 2 deletions(-) >> >> diff --git a/drivers/net/can/c_can/c_can.c b/drivers/net/can/c_can/c_can.c >> index 041525d..5d214d1 100644 >> --- a/drivers/net/can/c_can/c_can.c >> +++ b/drivers/net/can/c_can/c_can.c >> @@ -592,6 +592,7 @@ static int c_can_start(struct net_device *dev) >> { >> struct c_can_priv *priv = netdev_priv(dev); >> int err; >> + struct pinctrl *p; >> >> /* basic c_can configuration */ >> err = c_can_chip_config(dev); >> @@ -604,8 +605,13 @@ static int c_can_start(struct net_device *dev) >> >> priv->can.state = CAN_STATE_ERROR_ACTIVE; >> >> - /* activate pins */ >> - pinctrl_pm_select_default_state(dev->dev.parent); >> + /* Attempt to use "active" if available else use "default" */ >> + p = pinctrl_get_select(priv->device, "active"); >> + if (!IS_ERR(p)) >> + pinctrl_put(p); >> + else >> + pinctrl_pm_select_default_state(priv->device); >> + > > Thanks. This part looks good to me now. Is this an Acked-by? Marc
On 07/09/2015 01:59 PM, Marc Kleine-Budde wrote: > On 07/09/2015 12:58 PM, Grygorii Strashko wrote: >> On 07/08/2015 02:38 PM, Roger Quadros wrote: >>> From: "J.D. Schroeder" <jay.schroeder@garmin.com> >>> >>> The previous change 3973c526ae9c (net: can: c_can: Disable pins when CAN interface >>> is down) causes a slight glitch on the pinctrl settings when used. Since >>> commit ab78029 (drivers/pinctrl: grab default handles from device core), >>> the device core will automatically set the default pins. This causes >>> the pins to be momentarily set to the default and then to the sleep >>> state in register_c_can_dev(). By adding an optional "enable" state, >>> boards can set the default pin state to be disabled and avoid the >>> glitch when the switch from default to sleep first occurs. If the >>> "enable" state is not available c_can_pinctrl_select_state() falls >>> back to using the "default" pinctrl state. >>> >>> [Roger Q] - Forward port to v4.2 and use pinctrl_get_select(). >>> >>> Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com> >>> Signed-off-by: Roger Quadros <rogerq@ti.com> >>> --- >>> drivers/net/can/c_can/c_can.c | 10 ++++++++-- >>> 1 file changed, 8 insertions(+), 2 deletions(-) >>> >>> diff --git a/drivers/net/can/c_can/c_can.c b/drivers/net/can/c_can/c_can.c >>> index 041525d..5d214d1 100644 >>> --- a/drivers/net/can/c_can/c_can.c >>> +++ b/drivers/net/can/c_can/c_can.c >>> @@ -592,6 +592,7 @@ static int c_can_start(struct net_device *dev) >>> { >>> struct c_can_priv *priv = netdev_priv(dev); >>> int err; >>> + struct pinctrl *p; >>> >>> /* basic c_can configuration */ >>> err = c_can_chip_config(dev); >>> @@ -604,8 +605,13 @@ static int c_can_start(struct net_device *dev) >>> >>> priv->can.state = CAN_STATE_ERROR_ACTIVE; >>> >>> - /* activate pins */ >>> - pinctrl_pm_select_default_state(dev->dev.parent); >>> + /* Attempt to use "active" if available else use "default" */ >>> + p = pinctrl_get_select(priv->device, "active"); >>> + if (!IS_ERR(p)) >>> + pinctrl_put(p); >>> + else >>> + pinctrl_pm_select_default_state(priv->device); >>> + >> >> Thanks. This part looks good to me now. > > Is this an Acked-by? Not sure I can ack overall patch - is up to can driver maintainer for this part Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
diff --git a/drivers/net/can/c_can/c_can.c b/drivers/net/can/c_can/c_can.c index 041525d..5d214d1 100644 --- a/drivers/net/can/c_can/c_can.c +++ b/drivers/net/can/c_can/c_can.c @@ -592,6 +592,7 @@ static int c_can_start(struct net_device *dev) { struct c_can_priv *priv = netdev_priv(dev); int err; + struct pinctrl *p; /* basic c_can configuration */ err = c_can_chip_config(dev); @@ -604,8 +605,13 @@ static int c_can_start(struct net_device *dev) priv->can.state = CAN_STATE_ERROR_ACTIVE; - /* activate pins */ - pinctrl_pm_select_default_state(dev->dev.parent); + /* Attempt to use "active" if available else use "default" */ + p = pinctrl_get_select(priv->device, "active"); + if (!IS_ERR(p)) + pinctrl_put(p); + else + pinctrl_pm_select_default_state(priv->device); + return 0; }