@@ -11,13 +11,6 @@
cpus {
cpu@0 {
cpu0-supply = <&vcc>;
- operating-points = <
- /* kHz uV */
- 300000 1012500
- 600000 1200000
- 800000 1325000
- 1000000 1375000
- >;
};
};
@@ -16,19 +16,67 @@
/ {
cpus {
cpu: cpu@0 {
- /* OMAP343x/OMAP35xx variants OPP1-5 */
- operating-points = <
- /* kHz uV */
- 125000 975000
- 250000 1075000
- 500000 1200000
- 550000 1270000
- 600000 1350000
- >;
+ /* OMAP343x/OMAP35xx variants OPP1-6 */
+ operating-points-v2 = <&cpu0_opp_table>;
+
clock-latency = <300000>; /* From legacy driver */
};
};
+ /* see Documentation/devicetree/bindings/opp/opp.txt */
+ cpu0_opp_table: opp-table {
+ compatible = "operating-points-v2-ti-cpu";
+ syscon = <&scm_conf>;
+
+ opp1-125000000 {
+ opp-hz = /bits/ 64 <125000000>;
+ /*
+ * we currently only select the max voltage from table
+ * Table 3-3 of the omap3530 Data sheet (SPRS507F).
+ * Format is: <target min max>
+ */
+ opp-microvolt = <975000 975000 975000>;
+ /*
+ * first value is silicon revision bit mask
+ * second one 720MHz Device Identification bit mask
+ */
+ opp-supported-hw = <0xffffffff 3>;
+ };
+
+ opp2-250000000 {
+ opp-hz = /bits/ 64 <250000000>;
+ opp-microvolt = <1075000 1075000 1075000>;
+ opp-supported-hw = <0xffffffff 3>;
+ opp-suspend;
+ };
+
+ opp3-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <1200000 1200000 1200000>;
+ opp-supported-hw = <0xffffffff 3>;
+ };
+
+ opp4-550000000 {
+ opp-hz = /bits/ 64 <550000000>;
+ opp-microvolt = <1275000 1275000 1275000>;
+ opp-supported-hw = <0xffffffff 3>;
+ };
+
+ opp5-600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <1350000 1350000 1350000>;
+ opp-supported-hw = <0xffffffff 3>;
+ };
+
+ opp6-720000000 {
+ opp-hz = /bits/ 64 <720000000>;
+ opp-microvolt = <1350000 1350000 1350000>;
+ /* only high-speed grade omap3530 devices */
+ opp-supported-hw = <0xffffffff 2>;
+ turbo-mode;
+ };
+ };
+
ocp@68000000 {
omap3_pmx_core2: pinmux@480025d8 {
compatible = "ti,omap3-padconf", "pinctrl-single";
@@ -19,15 +19,53 @@
};
cpus {
- /* OMAP3630/OMAP37xx 'standard device' variants OPP50 to OPP130 */
+ /* OMAP3630/OMAP37xx variants OPP50 to OPP130 and OPP1G */
cpu: cpu@0 {
- operating-points = <
- /* kHz uV */
- 300000 1012500
- 600000 1200000
- 800000 1325000
- >;
- clock-latency = <300000>; /* From legacy driver */
+ operating-points-v2 = <&cpu0_opp_table>;
+
+ clock-latency = <300000>; /* From omap-cpufreq driver */
+ };
+ };
+
+ /* see Documentation/devicetree/bindings/opp/opp.txt */
+ cpu0_opp_table: opp-table {
+ compatible = "operating-points-v2-ti-cpu";
+ syscon = <&scm_conf>;
+
+ opp50-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ /*
+ * we currently only select the max voltage from table
+ * Table 4-19 of the DM3730 Data sheet (SPRS685B)
+ * Format is: <target min max>
+ */
+ opp-microvolt = <1012500 1012500 1012500>;
+ /*
+ * first value is silicon revision bit mask
+ * second one is "speed binned" bit mask
+ */
+ opp-supported-hw = <0xffffffff 3>;
+ opp-suspend;
+ };
+
+ opp100-600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <1200000 1200000 1200000>;
+ opp-supported-hw = <0xffffffff 3>;
+ };
+
+ opp130-800000000 {
+ opp-hz = /bits/ 64 <800000000>;
+ opp-microvolt = <1325000 1325000 1325000>;
+ opp-supported-hw = <0xffffffff 3>;
+ };
+
+ opp1g-1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <1375000 1375000 1375000>;
+ /* only on am/dm37x with speed-binned bit set */
+ opp-supported-hw = <0xffffffff 2>;
+ turbo-mode;
};
};
@@ -86,7 +86,6 @@ static const struct of_device_id whitelist[] __initconst = {
{ .compatible = "st-ericsson,u9540", },
{ .compatible = "ti,omap2", },
- { .compatible = "ti,omap3", },
{ .compatible = "ti,omap4", },
{ .compatible = "ti,omap5", },
@@ -132,6 +131,7 @@ static const struct of_device_id blacklist[] __initconst = {
{ .compatible = "ti,am33xx", },
{ .compatible = "ti,am43", },
{ .compatible = "ti,dra7", },
+ { .compatible = "ti,omap3", },
{ }
};
With the driver installed, we can change the opp-v1 table format to opp-v2. In addition, move omap3 from whitelist to blacklist in cpufreq-dt-platdev in the same patch, because doing either first breaks operation and may make trouble in bisect. We also can remove opp-v1 table for omap3-n950-n9 since its 1GHz capability is now automatically detected. We also fix a wrong OPP4 voltage for omap3430 which must be 0.6V + 54*12.5mV = 1275mV. Otherwise the twl4030 driver will reject this OPP. Note: the high speed OPPs that were not available in the opp-v1 tables are tagged "turbo-mode;" which means they are not automatically activated by the govenors or cpu-freq. To enable you have to write echo 1 >/sys/devices/system/cpu/cpufreq/boost Note: to hard disable an OPP in a board.dts file use e.g. &cpu0_opp_table: { /delete-node/ opp1g-1000000000; /* do not use */ }; or alternatively: &cpu0_opp_table: { opp1g-1000000000 { status = "disabled"; /* do not use */ }; }; Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Acked-by: Tony Lindgren <tony@atomide.com> --- arch/arm/boot/dts/omap3-n950-n9.dtsi | 7 --- arch/arm/boot/dts/omap34xx.dtsi | 66 ++++++++++++++++++++++++---- arch/arm/boot/dts/omap36xx.dtsi | 54 +++++++++++++++++++---- drivers/cpufreq/cpufreq-dt-platdev.c | 2 +- 4 files changed, 104 insertions(+), 25 deletions(-)