@@ -341,33 +341,26 @@ static int pci_call_probe(struct pci_dri
* on the right node.
*/
node = dev_to_node(&dev->dev);
+ dev->is_probed = 1;
+
+ cpu_hotplug_disable();
/*
- * On NUMA systems, we are likely to call a PF probe function using
- * work_on_cpu(). If that probe calls pci_enable_sriov() (which
- * adds the VF devices via pci_bus_add_device()), we may re-enter
- * this function to call the VF probe function. Calling
- * work_on_cpu() again will cause a lockdep warning. Since VFs are
- * always on the same node as the PF, we can work around this by
- * avoiding work_on_cpu() when we're already on the correct node.
- *
- * Preemption is enabled, so it's theoretically unsafe to use
- * numa_node_id(), but even if we run the probe function on the
- * wrong node, it should be functionally correct.
+ * Prevent nesting work_on_cpu() for the case where a Virtual Function
+ * device is probed from work_on_cpu() of the Physical device.
*/
- if (node >= 0 && node != numa_node_id()) {
- int cpu;
-
- cpu_hotplug_disable();
+ if (dev->is_virtfn && pci_physfn_is_probed(dev))
+ cpu = nr_cpu_ids;
+ else
cpu = cpumask_any_and(cpumask_of_node(node), cpu_online_mask);
- if (cpu < nr_cpu_ids)
- error = work_on_cpu(cpu, local_pci_probe, &ddi);
- else
- error = local_pci_probe(&ddi);
- cpu_hotplug_enable();
- } else
+
+ if (cpu < nr_cpu_ids)
+ error = work_on_cpu(cpu, local_pci_probe, &ddi);
+ else
error = local_pci_probe(&ddi);
+ dev->is_probed = 0;
+ cpu_hotplug_enable();
return error;
}
@@ -365,6 +365,7 @@ struct pci_dev {
unsigned int irq_managed:1;
unsigned int has_secondary_link:1;
unsigned int non_compliant_bars:1; /* broken BARs; ignore them */
+ unsigned int is_probed:1; /* device probing in progress */
pci_dev_flags_t dev_flags;
atomic_t enable_cnt; /* pci_enable_device has been called */
pci_call_probe() can called recursively when a physcial function is probed and the probing creates virtual functions, which are populated via pci_bus_add_device() which in turn can end up calling pci_call_probe() again. The code has an interesting way to prevent recursing into the workqueue code. That's accomplished by a check whether the current task runs already on the numa node which is associated with the device. While that works to prevent the recursion into the workqueue code, it's racy versus normal execution as there is no guarantee that the node does not vanish after the check. Make the detection reliable by: - Mark a probed device as 'is_probed' in pci_call_probe() - Check in pci_call_probe for a virtual function. If it's a virtual function and the associated physical function device is marked 'is_probed' then this is a recursive call, so the call can be invoked in the calling context. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: linux-pci@vger.kernel.org --- drivers/pci/pci-driver.c | 35 ++++++++++++++--------------------- include/linux/pci.h | 1 + 2 files changed, 15 insertions(+), 21 deletions(-)