@@ -3216,7 +3216,7 @@ void pci_configure_ari(struct pci_dev *dev)
return;
pcie_capability_read_dword(bridge, PCI_EXP_DEVCAP2, &cap);
- if (!(cap & PCI_EXP_DEVCAP2_ARI))
+ if ((cap == (u32)~0) || !(cap & PCI_EXP_DEVCAP2_ARI))
return;
if (pci_find_ext_capability(dev, PCI_EXT_CAP_ID_ARI)) {
@@ -3635,13 +3635,13 @@ int pci_enable_atomic_ops_to_root(struct pci_dev *dev, u32 cap_mask)
/* Ensure switch ports support AtomicOp routing */
case PCI_EXP_TYPE_UPSTREAM:
case PCI_EXP_TYPE_DOWNSTREAM:
- if (!(cap & PCI_EXP_DEVCAP2_ATOMIC_ROUTE))
+ if ((cap == (u32)~0) || !(cap & PCI_EXP_DEVCAP2_ATOMIC_ROUTE))
return -EINVAL;
break;
/* Ensure root port supports all the sizes we care about */
case PCI_EXP_TYPE_ROOT_PORT:
- if ((cap & cap_mask) != cap_mask)
+ if ((cap == (u32)~0) || ((cap & cap_mask) != cap_mask)
return -EINVAL;
break;
}
@@ -3650,7 +3650,7 @@ int pci_enable_atomic_ops_to_root(struct pci_dev *dev, u32 cap_mask)
if (pci_pcie_type(bridge) == PCI_EXP_TYPE_UPSTREAM) {
pcie_capability_read_dword(bridge, PCI_EXP_DEVCTL2,
&ctl2);
- if (ctl2 & PCI_EXP_DEVCTL2_ATOMIC_EGRESS_BLOCK)
+ if ((ctl2 != (u32)~0) && (ctl2 & PCI_EXP_DEVCTL2_ATOMIC_EGRESS_BLOCK))
return -EINVAL;
}
@@ -4512,7 +4512,7 @@ bool pcie_has_flr(struct pci_dev *dev)
return false;
pcie_capability_read_dword(dev, PCI_EXP_DEVCAP, &cap);
- return cap & PCI_EXP_DEVCAP_FLR;
+ return ((cap != (u32)~0) && (cap & PCI_EXP_DEVCAP_FLR));
}
EXPORT_SYMBOL_GPL(pcie_has_flr);
@@ -4672,19 +4672,19 @@ static bool pcie_wait_for_link_delay(struct pci_dev *pdev, bool active,
for (;;) {
pcie_capability_read_word(pdev, PCI_EXP_LNKSTA, &lnk_status);
ret = !!(lnk_status & PCI_EXP_LNKSTA_DLLLA);
- if (ret == active)
+ if ((lnk_status != (u16)~0) && (ret == active))
break;
if (timeout <= 0)
break;
msleep(10);
timeout -= 10;
}
- if (active && ret)
+ if ((lnk_status != (u16)~0) && active && ret)
msleep(delay);
- else if (ret != active)
+ else if ((lnk_status == (u16)~0) || (ret != active))
pci_info(pdev, "Data Link Layer Link Active not %s in 1000 msec\n",
active ? "set" : "cleared");
- return ret == active;
+ return ((lnk_status != (u16)~0) && (ret == active));
}
/**
@@ -5773,6 +5773,11 @@ u32 pcie_bandwidth_available(struct pci_dev *dev, struct pci_dev **limiting_dev,
while (dev) {
pcie_capability_read_word(dev, PCI_EXP_LNKSTA, &lnksta);
+ if (lnksta == (u16)~0) {
+ dev = pci_upstream_bridge(dev);
+ continue;
+ }
+
next_speed = pcie_link_speed[lnksta & PCI_EXP_LNKSTA_CLS];
next_width = (lnksta & PCI_EXP_LNKSTA_NLW) >>
PCI_EXP_LNKSTA_NLW_SHIFT;
@@ -5819,12 +5824,21 @@ enum pci_bus_speed pcie_get_speed_cap(struct pci_dev *dev)
* where only 2.5 GT/s and 5.0 GT/s speeds were defined.
*/
pcie_capability_read_dword(dev, PCI_EXP_LNKCAP2, &lnkcap2);
+ if (lnkcap2 == (u32)~0) {
+ dev_err(dev, "Read link speed capability has failed.\n");
+ return PCI_SPEED_UNKNOWN;
+ }
/* PCIe r3.0-compliant */
if (lnkcap2)
return PCIE_LNKCAP2_SLS2SPEED(lnkcap2);
pcie_capability_read_dword(dev, PCI_EXP_LNKCAP, &lnkcap);
+ if (lnkcap == (u32)~0) {
+ dev_err(dev, "Read link speed capability has failed.\n");
+ return PCI_SPEED_UNKNOWN;
+ }
+
if ((lnkcap & PCI_EXP_LNKCAP_SLS) == PCI_EXP_LNKCAP_SLS_5_0GB)
return PCIE_SPEED_5_0GT;
else if ((lnkcap & PCI_EXP_LNKCAP_SLS) == PCI_EXP_LNKCAP_SLS_2_5GB)
@@ -5846,7 +5860,7 @@ enum pcie_link_width pcie_get_width_cap(struct pci_dev *dev)
u32 lnkcap;
pcie_capability_read_dword(dev, PCI_EXP_LNKCAP, &lnkcap);
- if (lnkcap)
+ if (lnkcap && (lnkcap != (u32)~0))
return (lnkcap & PCI_EXP_LNKCAP_MLW) >> 4;
return PCIE_LNK_WIDTH_UNKNOWN;
On failure pcie_capability_read_*() sets it's last parameter, val to 0. However, with Patch 12/12, it is possible that val is set to ~0 on failure. This would introduce a bug because (x & x) == (~0 & x). Since ~0 is an invalid value in here, Add extra check for ~0 to ensure success or failure. pci_enable_atomic_ops_to_root(): Continue looping through the device heirarchy on failure. pcie_wait_for_link_delay(): Add extra check for ~0 to the condition for breaking out of the loop. Delay only on success otherwise report error and return false. pcie_bandwidth_available(): On read failure move up the device heirarchy and continue. pcie_get_speed_cap(): On read failure, report error and return PCI_SPEED_UNKNOWN Suggested-by: Bjorn Helgaas <bjorn@helgaas.com> Signed-off-by: Saheed O. Bolarinwa <refactormyself@gmail.com> --- drivers/pci/pci.c | 34 ++++++++++++++++++++++++---------- 1 file changed, 24 insertions(+), 10 deletions(-)