| Message ID | 068a44b38a01740b06ea3646611c8dfdacf3f7b0.1689913334.git.quic_varada@quicinc.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Enable IPQ5332 USB2 | expand |
On Fri, Jul 21, 2023 at 10:05:28AM +0530, Varadarajan Narayanan wrote: > Add the M31 USB2 phy driver. Is it possible to extend this description a little bit? E.g. mention where this PHY is used. > > Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com> > --- > v5: > Kconfig and Makefile:- place snippet according to sorted order > Use generic phy instead of usb-phy > Use ARRAY_SIZE for reg init instead of blank last entry > Fix copyright year > > v4: > Remove unused enum > Error handling for devm_clk_get > v1: > Combine driver, makefile and kconfig into 1 patch > Remove 'qscratch' region and its usage. The controller driver takes care > of those settings > Use compatible/data to handle ipq5332 init > Drop the default case > Get resources by index instead of name as there is only one resource > Add clock > Fix review comments in the driver > --- > drivers/phy/qualcomm/Kconfig | 11 ++ > drivers/phy/qualcomm/Makefile | 1 + > drivers/phy/qualcomm/phy-qcom-m31.c | 264 ++++++++++++++++++++++++++++++++++++ > 3 files changed, 276 insertions(+) > create mode 100644 drivers/phy/qualcomm/phy-qcom-m31.c > > diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig > index ced6038..d638906 100644 > --- a/drivers/phy/qualcomm/Kconfig > +++ b/drivers/phy/qualcomm/Kconfig > @@ -143,6 +143,17 @@ config PHY_QCOM_EUSB2_REPEATER > PMICs. The repeater is paired with a Synopsys eUSB2 Phy > on Qualcomm SOCs. > > +config PHY_QCOM_M31_USB > + tristate "Qualcomm M31 HS PHY driver support" > + depends on (USB || USB_GADGET) && ARCH_QCOM The USB part seems reasonable, but it's not clear to me why you depend on USB_GADGET. And this is the only option in this directory that depends on it's consumer subsystem... It is reasonable help the user not choose the driver if ARCH_QCOM is disabled, but most other options in this file allow compilation during COMPILE_TEST. This provides additional build coverage, so perhaps you could adopt this as well? > + select USB_PHY USB_PHY is for drivers in drivers/usb/phy, but you're using the generic PHY framework. Is this really needed, or just a remnant from downstream? You should however select GENERIC_PHY, like all other options in this file. > + help > + Enable this to support M31 HS PHY transceivers on Qualcomm chips > + with DWC3 USB core. It handles PHY initialization, clock > + management required after resetting the hardware and power > + management. This driver is required even for peripheral only or > + host only mode configurations. > + > config PHY_QCOM_USB_HS > tristate "Qualcomm USB HS PHY module" > depends on USB_ULPI_BUS > diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile > index df94581..ffd609a 100644 > --- a/drivers/phy/qualcomm/Makefile > +++ b/drivers/phy/qualcomm/Makefile > @@ -4,6 +4,7 @@ obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o > obj-$(CONFIG_PHY_QCOM_EDP) += phy-qcom-edp.o > obj-$(CONFIG_PHY_QCOM_IPQ4019_USB) += phy-qcom-ipq4019-usb.o > obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o > +obj-$(CONFIG_PHY_QCOM_M31_USB) += phy-qcom-m31.o > obj-$(CONFIG_PHY_QCOM_PCIE2) += phy-qcom-pcie2.o > > obj-$(CONFIG_PHY_QCOM_QMP_COMBO) += phy-qcom-qmp-combo.o > diff --git a/drivers/phy/qualcomm/phy-qcom-m31.c b/drivers/phy/qualcomm/phy-qcom-m31.c > new file mode 100644 > index 0000000..4627425 > --- /dev/null > +++ b/drivers/phy/qualcomm/phy-qcom-m31.c > @@ -0,0 +1,264 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright (c) 2014-2016, 2020-2023, The Linux Foundation. All rights reserved. Please fix this. > + */ > + > +#include <linux/clk.h> > +#include <linux/delay.h> > +#include <linux/err.h> > +#include <linux/io.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/of_device.h> Rob Herring has posted a bunch of patches lately removing uses of of_device.h, so please don't introduce a new one. of.h and of_platform.h are to be used instead. > +#include <linux/of.h> > +#include <linux/platform_device.h> > +#include <linux/reset.h> > +#include <linux/slab.h> > +#include <linux/usb/of.h> > +#include <linux/usb/phy.h> I don't think you need the last two, in a generic phy driver. > + > +#define USB2PHY_PORT_UTMI_CTRL1 0x40 > + > +#define USB2PHY_PORT_UTMI_CTRL2 0x44 > + #define UTMI_ULPI_SEL BIT(7) > + #define UTMI_TEST_MUX_SEL BIT(6) > + > +#define HS_PHY_CTRL_REG 0x10 > + #define UTMI_OTG_VBUS_VALID BIT(20) > + #define SW_SESSVLD_SEL BIT(28) > + > +#define USB_PHY_UTMI_CTRL0 0x3c > + > +#define USB_PHY_UTMI_CTRL5 0x50 > + #define POR_EN BIT(1) > + > +#define USB_PHY_HS_PHY_CTRL_COMMON0 0x54 > + #define COMMONONN BIT(7) > + #define FSEL BIT(4) > + #define RETENABLEN BIT(3) > + #define FREQ_24MHZ (GENMASK(6, 6) | GENMASK(4, 4)) > + > +#define USB_PHY_HS_PHY_CTRL2 0x64 > + #define USB2_SUSPEND_N_SEL BIT(3) > + #define USB2_SUSPEND_N BIT(2) > + #define USB2_UTMI_CLK_EN BIT(1) > + > +#define USB_PHY_CFG0 0x94 > + #define UTMI_PHY_OVERRIDE_EN BIT(1) > + > +#define USB_PHY_REFCLK_CTRL 0xa0 > + #define CLKCORE BIT(1) > + > +#define USB2PHY_PORT_POWERDOWN 0xa4 > + #define POWER_UP BIT(0) > + #define POWER_DOWN 0 > + > +#define USB_PHY_FSEL_SEL 0xb8 > + #define FREQ_SEL BIT(0) > + > +#define USB2PHY_USB_PHY_M31_XCFGI_1 0xbc > + #define USB2_0_TX_ENABLE BIT(2) > + > +#define USB2PHY_USB_PHY_M31_XCFGI_4 0xc8 > + #define HSTX_SLEW_RATE_565PS GENMASK(1, 0) > + #define PLL_CHARGING_PUMP_CURRENT_35UA GENMASK(4, 3) > + #define ODT_VALUE_38_02_OHM GENMASK(7, 6) > + > +#define USB2PHY_USB_PHY_M31_XCFGI_5 0xcc > + #define ODT_VALUE_45_02_OHM BIT(2) > + #define HSTX_PRE_EMPHASIS_LEVEL_0_55MA BIT(0) > + > +#define USB2PHY_USB_PHY_M31_XCFGI_11 0xe4 > + #define XCFG_COARSE_TUNE_NUM BIT(1) > + #define XCFG_FINE_TUNE_NUM BIT(3) > + > +struct m31_phy_regs { > + u32 off; > + u32 val; > + u32 delay; > +}; > + > +struct m31_priv_data { > + bool ulpi_mode; > + const struct m31_phy_regs *regs; > + const int nregs; Doesn't hurt to spell out that this is an unsigned int, and you don't need the const on the nregs. > +}; > + > +#define M31_REG(__o, __v, __d) \ > + { .off = __o, .val = __v, .delay = __d } This macro doesn't add any value. Compare: M31_REG(USB_PHY_CFG0, UTMI_PHY_OVERRIDE_EN, 0), with: { USB_PHY_CFG0, UTMI_PHY_OVERRIDE_EN, 0 }, > + > +struct m31_phy_regs m31_ipq5332_regs[] = { > + M31_REG(USB_PHY_CFG0, UTMI_PHY_OVERRIDE_EN, 0), > + M31_REG(USB_PHY_UTMI_CTRL5, POR_EN, 15), > + M31_REG(USB_PHY_FSEL_SEL, FREQ_SEL, 0), > + M31_REG(USB_PHY_HS_PHY_CTRL_COMMON0, > + COMMONONN | FREQ_24MHZ | RETENABLEN, 0), The guideline is to keep under 80 characters, but if it improves readability you may use up to 100. So this line can be unwrapped. > + M31_REG(USB_PHY_UTMI_CTRL5, POR_EN, 0), > + M31_REG(USB_PHY_HS_PHY_CTRL2, > + USB2_SUSPEND_N_SEL | USB2_SUSPEND_N | USB2_UTMI_CLK_EN, 0), This one as well. > + M31_REG(USB2PHY_USB_PHY_M31_XCFGI_11, > + XCFG_COARSE_TUNE_NUM | XCFG_FINE_TUNE_NUM, 0), > + M31_REG(USB2PHY_USB_PHY_M31_XCFGI_4, > + HSTX_SLEW_RATE_565PS | PLL_CHARGING_PUMP_CURRENT_35UA | > + ODT_VALUE_38_02_OHM, 0), > + M31_REG(USB2PHY_USB_PHY_M31_XCFGI_1, USB2_0_TX_ENABLE, 0), > + M31_REG(USB2PHY_USB_PHY_M31_XCFGI_5, > + ODT_VALUE_45_02_OHM | HSTX_PRE_EMPHASIS_LEVEL_0_55MA, 4), And this one, if you drop the M32_REG macro. > + M31_REG(USB_PHY_UTMI_CTRL5, 0x0, 0), > + M31_REG(USB_PHY_HS_PHY_CTRL2, USB2_SUSPEND_N | USB2_UTMI_CLK_EN, 0), > +}; > + > +struct m31usb_phy { > + struct phy *phy; > + void __iomem *base; > + const struct m31_phy_regs *regs; > + int nregs; > + > + struct clk *cfg_ahb_clk; If you only have one clock, you can name it "clk" without causing confusion. > + struct reset_control *phy_reset; Same here, if there's only one reset, then "reset" is a sufficient name. > + > + bool cable_connected; Unused > + bool suspended; Unused, are you missing/omitting some relevant code here? > + bool ulpi_mode; > +}; > + > +static void m31usb_phy_enable_clock(struct m31usb_phy *qphy) It wouldn't hurt to just move this code into m31usb_phy_init(). > +{ > + const struct m31_phy_regs *regs = qphy->regs; > + int i; > + > + for (i = 0; i < qphy->nregs; i++) { > + writel(regs[i].val, qphy->base + regs[i].off); > + if (regs[i].delay) > + udelay(regs[i].delay); > + } > +} > + > +static int m31usb_phy_init(struct phy *phy) > +{ > + int ret; > + struct m31usb_phy *qphy = phy_get_drvdata(phy); > + > + ret = clk_prepare_enable(qphy->cfg_ahb_clk); > + if (ret) { > + dev_err(&phy->dev, "failed to enable cfg ahb clock, %d\n", ret); > + return ret; > + } > + > + /* Perform phy reset */ > + reset_control_assert(qphy->phy_reset); > + udelay(5); > + reset_control_deassert(qphy->phy_reset); > + > + /* configure for ULPI mode if requested */ > + if (qphy->ulpi_mode) > + writel(0x0, qphy->base + USB2PHY_PORT_UTMI_CTRL2); > + > + /* Enable the PHY */ > + writel(POWER_UP, qphy->base + USB2PHY_PORT_POWERDOWN); > + > + /* Make sure above write completed */ That's not what wmb() does. It ensures that any writes prior to this line is completed before any writes after this. But m31usb_phy_enable_clock() is using writel(), which does the same already. If you really need the previous writes to have completed (get through the write buffer etc), then you need to readl() the same register back. But I see no reason for that. > + wmb(); So I think this should go. > + > + /* Turn on phy ref clock */ > + m31usb_phy_enable_clock(qphy); > + > + return 0; > +} > + > +static int m31usb_phy_shutdown(struct phy *phy) > +{ > + struct m31usb_phy *qphy = phy_get_drvdata(phy); > + > + /* Disable the PHY */ > + writel_relaxed(POWER_DOWN, qphy->base + USB2PHY_PORT_POWERDOWN); > + /* Make sure above write completed */ > + wmb(); Same as above. Although here you would assume that clk_disable_unprepare() uses writel() and doesn't overtake your power-down write, but that sounds like reasonable assumptions to make. > + > + clk_disable_unprepare(qphy->cfg_ahb_clk); > + > + return 0; > +} > + > +static const struct phy_ops m31usb_phy_gen_ops = { > + .power_on = m31usb_phy_init, > + .power_off = m31usb_phy_shutdown, > + .owner = THIS_MODULE, > +}; > + > +static int m31usb_phy_probe(struct platform_device *pdev) > +{ > + const struct m31_priv_data *data; > + struct device *dev = &pdev->dev; > + struct m31usb_phy *qphy; > + struct phy_provider *phy_provider; > + int ret; Please sort these in descending length order (reverse xmas tree). > + > + qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL); > + if (!qphy) > + return -ENOMEM; > + > + qphy->base = devm_platform_ioremap_resource(pdev, 0); > + if (IS_ERR(qphy->base)) > + return PTR_ERR(qphy->base); > + > + qphy->phy_reset = devm_reset_control_get_exclusive_by_index(dev, 0); > + if (IS_ERR(qphy->phy_reset)) > + return PTR_ERR(qphy->phy_reset); > + > + qphy->cfg_ahb_clk = devm_clk_get(dev, "cfg_ahb"); If you only have one clock, then omitting clock-names and do devm_clk_get(dev, NULL) works well. > + if (IS_ERR(qphy->cfg_ahb_clk)) { > + ret = PTR_ERR(qphy->cfg_ahb_clk); > + dev_err(dev, "failed to get cfg_ahb clock, %d\n", ret); > + return ret; Replace these tree lines with: return dev_err_probe(dev, PTR_ERR(qphy->cfg_ahb_clk), "failed to get cfg_ahb_clk\n"); > + } > + > + platform_set_drvdata(pdev, qphy); There are no platform_get_drvdata() calls in this driver, so you can omit this. > + > + data = of_device_get_match_data(dev); > + qphy->regs = data->regs; > + qphy->nregs = data->nregs; > + qphy->ulpi_mode = data->ulpi_mode; > + > + qphy->phy = devm_phy_create(dev, NULL, &m31usb_phy_gen_ops); > + if (IS_ERR(qphy->phy)) { > + ret = PTR_ERR(qphy->phy); > + dev_err(dev, "failed to create phy, %d\n", ret); > + qphy->phy = NULL; qphy is inaccessible, and freed after the next line, no need to clear this. > + return ret; > + } > + > + dev_set_drvdata(dev, qphy); This is exactly he same as platform_set_drvdata() above, so per the same logic you can drop this as well. > + phy_set_drvdata(qphy->phy, qphy); > + > + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); > + if (!IS_ERR(phy_provider)) > + dev_info(dev, "Registered M31 USB phy\n"); > + > + return PTR_ERR_OR_ZERO(phy_provider); > +} > + > +static const struct m31_priv_data m31_ipq5332_data = { > + .ulpi_mode = false, > + .regs = m31_ipq5332_regs, > + .nregs = ARRAY_SIZE(m31_ipq5332_regs), > +}; > + > +static const struct of_device_id m31usb_phy_id_table[] = { > + { .compatible = "qcom,ipq5332-usb-hsphy", .data = &m31_ipq5332_data }, > + { }, > +}; > +MODULE_DEVICE_TABLE(of, m31usb_phy_id_table); > + > +static struct platform_driver m31usb_phy_driver = { > + .probe = m31usb_phy_probe, Please drop the indentation in these. Regards, Bjorn
diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig index ced6038..d638906 100644 --- a/drivers/phy/qualcomm/Kconfig +++ b/drivers/phy/qualcomm/Kconfig @@ -143,6 +143,17 @@ config PHY_QCOM_EUSB2_REPEATER PMICs. The repeater is paired with a Synopsys eUSB2 Phy on Qualcomm SOCs. +config PHY_QCOM_M31_USB + tristate "Qualcomm M31 HS PHY driver support" + depends on (USB || USB_GADGET) && ARCH_QCOM + select USB_PHY + help + Enable this to support M31 HS PHY transceivers on Qualcomm chips + with DWC3 USB core. It handles PHY initialization, clock + management required after resetting the hardware and power + management. This driver is required even for peripheral only or + host only mode configurations. + config PHY_QCOM_USB_HS tristate "Qualcomm USB HS PHY module" depends on USB_ULPI_BUS diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile index df94581..ffd609a 100644 --- a/drivers/phy/qualcomm/Makefile +++ b/drivers/phy/qualcomm/Makefile @@ -4,6 +4,7 @@ obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o obj-$(CONFIG_PHY_QCOM_EDP) += phy-qcom-edp.o obj-$(CONFIG_PHY_QCOM_IPQ4019_USB) += phy-qcom-ipq4019-usb.o obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o +obj-$(CONFIG_PHY_QCOM_M31_USB) += phy-qcom-m31.o obj-$(CONFIG_PHY_QCOM_PCIE2) += phy-qcom-pcie2.o obj-$(CONFIG_PHY_QCOM_QMP_COMBO) += phy-qcom-qmp-combo.o diff --git a/drivers/phy/qualcomm/phy-qcom-m31.c b/drivers/phy/qualcomm/phy-qcom-m31.c new file mode 100644 index 0000000..4627425 --- /dev/null +++ b/drivers/phy/qualcomm/phy-qcom-m31.c @@ -0,0 +1,264 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (c) 2014-2016, 2020-2023, The Linux Foundation. All rights reserved. + */ + +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/reset.h> +#include <linux/slab.h> +#include <linux/usb/of.h> +#include <linux/usb/phy.h> + +#define USB2PHY_PORT_UTMI_CTRL1 0x40 + +#define USB2PHY_PORT_UTMI_CTRL2 0x44 + #define UTMI_ULPI_SEL BIT(7) + #define UTMI_TEST_MUX_SEL BIT(6) + +#define HS_PHY_CTRL_REG 0x10 + #define UTMI_OTG_VBUS_VALID BIT(20) + #define SW_SESSVLD_SEL BIT(28) + +#define USB_PHY_UTMI_CTRL0 0x3c + +#define USB_PHY_UTMI_CTRL5 0x50 + #define POR_EN BIT(1) + +#define USB_PHY_HS_PHY_CTRL_COMMON0 0x54 + #define COMMONONN BIT(7) + #define FSEL BIT(4) + #define RETENABLEN BIT(3) + #define FREQ_24MHZ (GENMASK(6, 6) | GENMASK(4, 4)) + +#define USB_PHY_HS_PHY_CTRL2 0x64 + #define USB2_SUSPEND_N_SEL BIT(3) + #define USB2_SUSPEND_N BIT(2) + #define USB2_UTMI_CLK_EN BIT(1) + +#define USB_PHY_CFG0 0x94 + #define UTMI_PHY_OVERRIDE_EN BIT(1) + +#define USB_PHY_REFCLK_CTRL 0xa0 + #define CLKCORE BIT(1) + +#define USB2PHY_PORT_POWERDOWN 0xa4 + #define POWER_UP BIT(0) + #define POWER_DOWN 0 + +#define USB_PHY_FSEL_SEL 0xb8 + #define FREQ_SEL BIT(0) + +#define USB2PHY_USB_PHY_M31_XCFGI_1 0xbc + #define USB2_0_TX_ENABLE BIT(2) + +#define USB2PHY_USB_PHY_M31_XCFGI_4 0xc8 + #define HSTX_SLEW_RATE_565PS GENMASK(1, 0) + #define PLL_CHARGING_PUMP_CURRENT_35UA GENMASK(4, 3) + #define ODT_VALUE_38_02_OHM GENMASK(7, 6) + +#define USB2PHY_USB_PHY_M31_XCFGI_5 0xcc + #define ODT_VALUE_45_02_OHM BIT(2) + #define HSTX_PRE_EMPHASIS_LEVEL_0_55MA BIT(0) + +#define USB2PHY_USB_PHY_M31_XCFGI_11 0xe4 + #define XCFG_COARSE_TUNE_NUM BIT(1) + #define XCFG_FINE_TUNE_NUM BIT(3) + +struct m31_phy_regs { + u32 off; + u32 val; + u32 delay; +}; + +struct m31_priv_data { + bool ulpi_mode; + const struct m31_phy_regs *regs; + const int nregs; +}; + +#define M31_REG(__o, __v, __d) \ + { .off = __o, .val = __v, .delay = __d } + +struct m31_phy_regs m31_ipq5332_regs[] = { + M31_REG(USB_PHY_CFG0, UTMI_PHY_OVERRIDE_EN, 0), + M31_REG(USB_PHY_UTMI_CTRL5, POR_EN, 15), + M31_REG(USB_PHY_FSEL_SEL, FREQ_SEL, 0), + M31_REG(USB_PHY_HS_PHY_CTRL_COMMON0, + COMMONONN | FREQ_24MHZ | RETENABLEN, 0), + M31_REG(USB_PHY_UTMI_CTRL5, POR_EN, 0), + M31_REG(USB_PHY_HS_PHY_CTRL2, + USB2_SUSPEND_N_SEL | USB2_SUSPEND_N | USB2_UTMI_CLK_EN, 0), + M31_REG(USB2PHY_USB_PHY_M31_XCFGI_11, + XCFG_COARSE_TUNE_NUM | XCFG_FINE_TUNE_NUM, 0), + M31_REG(USB2PHY_USB_PHY_M31_XCFGI_4, + HSTX_SLEW_RATE_565PS | PLL_CHARGING_PUMP_CURRENT_35UA | + ODT_VALUE_38_02_OHM, 0), + M31_REG(USB2PHY_USB_PHY_M31_XCFGI_1, USB2_0_TX_ENABLE, 0), + M31_REG(USB2PHY_USB_PHY_M31_XCFGI_5, + ODT_VALUE_45_02_OHM | HSTX_PRE_EMPHASIS_LEVEL_0_55MA, 4), + M31_REG(USB_PHY_UTMI_CTRL5, 0x0, 0), + M31_REG(USB_PHY_HS_PHY_CTRL2, USB2_SUSPEND_N | USB2_UTMI_CLK_EN, 0), +}; + +struct m31usb_phy { + struct phy *phy; + void __iomem *base; + const struct m31_phy_regs *regs; + int nregs; + + struct clk *cfg_ahb_clk; + struct reset_control *phy_reset; + + bool cable_connected; + bool suspended; + bool ulpi_mode; +}; + +static void m31usb_phy_enable_clock(struct m31usb_phy *qphy) +{ + const struct m31_phy_regs *regs = qphy->regs; + int i; + + for (i = 0; i < qphy->nregs; i++) { + writel(regs[i].val, qphy->base + regs[i].off); + if (regs[i].delay) + udelay(regs[i].delay); + } +} + +static int m31usb_phy_init(struct phy *phy) +{ + int ret; + struct m31usb_phy *qphy = phy_get_drvdata(phy); + + ret = clk_prepare_enable(qphy->cfg_ahb_clk); + if (ret) { + dev_err(&phy->dev, "failed to enable cfg ahb clock, %d\n", ret); + return ret; + } + + /* Perform phy reset */ + reset_control_assert(qphy->phy_reset); + udelay(5); + reset_control_deassert(qphy->phy_reset); + + /* configure for ULPI mode if requested */ + if (qphy->ulpi_mode) + writel(0x0, qphy->base + USB2PHY_PORT_UTMI_CTRL2); + + /* Enable the PHY */ + writel(POWER_UP, qphy->base + USB2PHY_PORT_POWERDOWN); + + /* Make sure above write completed */ + wmb(); + + /* Turn on phy ref clock */ + m31usb_phy_enable_clock(qphy); + + return 0; +} + +static int m31usb_phy_shutdown(struct phy *phy) +{ + struct m31usb_phy *qphy = phy_get_drvdata(phy); + + /* Disable the PHY */ + writel_relaxed(POWER_DOWN, qphy->base + USB2PHY_PORT_POWERDOWN); + /* Make sure above write completed */ + wmb(); + + clk_disable_unprepare(qphy->cfg_ahb_clk); + + return 0; +} + +static const struct phy_ops m31usb_phy_gen_ops = { + .power_on = m31usb_phy_init, + .power_off = m31usb_phy_shutdown, + .owner = THIS_MODULE, +}; + +static int m31usb_phy_probe(struct platform_device *pdev) +{ + const struct m31_priv_data *data; + struct device *dev = &pdev->dev; + struct m31usb_phy *qphy; + struct phy_provider *phy_provider; + int ret; + + qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL); + if (!qphy) + return -ENOMEM; + + qphy->base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(qphy->base)) + return PTR_ERR(qphy->base); + + qphy->phy_reset = devm_reset_control_get_exclusive_by_index(dev, 0); + if (IS_ERR(qphy->phy_reset)) + return PTR_ERR(qphy->phy_reset); + + qphy->cfg_ahb_clk = devm_clk_get(dev, "cfg_ahb"); + if (IS_ERR(qphy->cfg_ahb_clk)) { + ret = PTR_ERR(qphy->cfg_ahb_clk); + dev_err(dev, "failed to get cfg_ahb clock, %d\n", ret); + return ret; + } + + platform_set_drvdata(pdev, qphy); + + data = of_device_get_match_data(dev); + qphy->regs = data->regs; + qphy->nregs = data->nregs; + qphy->ulpi_mode = data->ulpi_mode; + + qphy->phy = devm_phy_create(dev, NULL, &m31usb_phy_gen_ops); + if (IS_ERR(qphy->phy)) { + ret = PTR_ERR(qphy->phy); + dev_err(dev, "failed to create phy, %d\n", ret); + qphy->phy = NULL; + return ret; + } + + dev_set_drvdata(dev, qphy); + phy_set_drvdata(qphy->phy, qphy); + + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); + if (!IS_ERR(phy_provider)) + dev_info(dev, "Registered M31 USB phy\n"); + + return PTR_ERR_OR_ZERO(phy_provider); +} + +static const struct m31_priv_data m31_ipq5332_data = { + .ulpi_mode = false, + .regs = m31_ipq5332_regs, + .nregs = ARRAY_SIZE(m31_ipq5332_regs), +}; + +static const struct of_device_id m31usb_phy_id_table[] = { + { .compatible = "qcom,ipq5332-usb-hsphy", .data = &m31_ipq5332_data }, + { }, +}; +MODULE_DEVICE_TABLE(of, m31usb_phy_id_table); + +static struct platform_driver m31usb_phy_driver = { + .probe = m31usb_phy_probe, + .driver = { + .name = "qcom-m31usb-phy", + .of_match_table = m31usb_phy_id_table, + }, +}; + +module_platform_driver(m31usb_phy_driver); + +MODULE_DESCRIPTION("USB2 Qualcomm M31 HSPHY driver"); +MODULE_LICENSE("GPL");
Add the M31 USB2 phy driver. Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com> --- v5: Kconfig and Makefile:- place snippet according to sorted order Use generic phy instead of usb-phy Use ARRAY_SIZE for reg init instead of blank last entry Fix copyright year v4: Remove unused enum Error handling for devm_clk_get v1: Combine driver, makefile and kconfig into 1 patch Remove 'qscratch' region and its usage. The controller driver takes care of those settings Use compatible/data to handle ipq5332 init Drop the default case Get resources by index instead of name as there is only one resource Add clock Fix review comments in the driver --- drivers/phy/qualcomm/Kconfig | 11 ++ drivers/phy/qualcomm/Makefile | 1 + drivers/phy/qualcomm/phy-qcom-m31.c | 264 ++++++++++++++++++++++++++++++++++++ 3 files changed, 276 insertions(+) create mode 100644 drivers/phy/qualcomm/phy-qcom-m31.c