diff mbox series

[v3,2/3] phy/rockchip: add naneng combo phy for RK3568

Message ID 20211025080632.32063-3-yifeng.zhao@rock-chips.com
State Superseded
Headers show
Series Add Naneng combo PHY support for RK3568 | expand

Commit Message

Yifeng Zhao Oct. 25, 2021, 8:06 a.m. UTC
This patch implements a combo phy driver for Rockchip SoCs
with NaNeng IP block. This phy can be used as pcie-phy, usb3-phy,
sata-phy or sgmii-phy.

Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
---

Changes in v3:
- Using api devm_reset_control_get_optional_exclusive and dev_err_probe
- Remove apb_rst
- Redefine registers address

Changes in v2:
- Using api devm_platform_get_and_ioremap_resource.
- Modify rockchip_combphy_set_Mode.
- Add some PHY registers definition.

 drivers/phy/rockchip/Kconfig                  |   8 +
 drivers/phy/rockchip/Makefile                 |   1 +
 .../rockchip/phy-rockchip-naneng-combphy.c    | 638 ++++++++++++++++++
 3 files changed, 647 insertions(+)
 create mode 100644 drivers/phy/rockchip/phy-rockchip-naneng-combphy.c

Comments

Kever Yang Nov. 8, 2021, 2:50 a.m. UTC | #1
Looks good to me.


Reviewed-by: Kever Yang <kever.yang@rock-chips.com>


Thanks,
- Kever

On 2021/10/25 下午4:06, Yifeng Zhao wrote:
> This patch implements a combo phy driver for Rockchip SoCs
> with NaNeng IP block. This phy can be used as pcie-phy, usb3-phy,
> sata-phy or sgmii-phy.
>
> Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
> ---
>
> Changes in v3:
> - Using api devm_reset_control_get_optional_exclusive and dev_err_probe
> - Remove apb_rst
> - Redefine registers address
>
> Changes in v2:
> - Using api devm_platform_get_and_ioremap_resource.
> - Modify rockchip_combphy_set_Mode.
> - Add some PHY registers definition.
>
>   drivers/phy/rockchip/Kconfig                  |   8 +
>   drivers/phy/rockchip/Makefile                 |   1 +
>   .../rockchip/phy-rockchip-naneng-combphy.c    | 638 ++++++++++++++++++
>   3 files changed, 647 insertions(+)
>   create mode 100644 drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
>
> diff --git a/drivers/phy/rockchip/Kconfig b/drivers/phy/rockchip/Kconfig
> index e812adad7242..9022e395c056 100644
> --- a/drivers/phy/rockchip/Kconfig
> +++ b/drivers/phy/rockchip/Kconfig
> @@ -66,6 +66,14 @@ config PHY_ROCKCHIP_INNO_DSIDPHY
>   	  Enable this to support the Rockchip MIPI/LVDS/TTL PHY with
>   	  Innosilicon IP block.
>   
> +config PHY_ROCKCHIP_NANENG_COMBO_PHY
> +	tristate "Rockchip NANENG COMBO PHY Driver"
> +	depends on ARCH_ROCKCHIP && OF
> +	select GENERIC_PHY
> +	help
> +	  Enable this to support the Rockchip PCIe/USB3.0/SATA/QSGMII
> +	  combo PHY with NaNeng IP block.
> +
>   config PHY_ROCKCHIP_PCIE
>   	tristate "Rockchip PCIe PHY Driver"
>   	depends on (ARCH_ROCKCHIP && OF) || COMPILE_TEST
> diff --git a/drivers/phy/rockchip/Makefile b/drivers/phy/rockchip/Makefile
> index f0eec212b2aa..a5041efb5b8f 100644
> --- a/drivers/phy/rockchip/Makefile
> +++ b/drivers/phy/rockchip/Makefile
> @@ -6,6 +6,7 @@ obj-$(CONFIG_PHY_ROCKCHIP_INNO_CSIDPHY)	+= phy-rockchip-inno-csidphy.o
>   obj-$(CONFIG_PHY_ROCKCHIP_INNO_DSIDPHY)	+= phy-rockchip-inno-dsidphy.o
>   obj-$(CONFIG_PHY_ROCKCHIP_INNO_HDMI)	+= phy-rockchip-inno-hdmi.o
>   obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
> +obj-$(CONFIG_PHY_ROCKCHIP_NANENG_COMBO_PHY)	+= phy-rockchip-naneng-combphy.o
>   obj-$(CONFIG_PHY_ROCKCHIP_PCIE)		+= phy-rockchip-pcie.o
>   obj-$(CONFIG_PHY_ROCKCHIP_TYPEC)	+= phy-rockchip-typec.o
>   obj-$(CONFIG_PHY_ROCKCHIP_USB)		+= phy-rockchip-usb.o
> diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> new file mode 100644
> index 000000000000..e5bea21a1d35
> --- /dev/null
> +++ b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> @@ -0,0 +1,638 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Rockchip PIPE USB3.0 PCIE SATA combphy driver
> + *
> + * Copyright (C) 2021 Rockchip Electronics Co., Ltd.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/phy/phy.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include <dt-bindings/phy/phy.h>
> +
> +#define BIT_WRITEABLE_SHIFT		16
> +#define REF_CLOCK_24MHz			24000000
> +#define REF_CLOCK_25MHz			25000000
> +#define REF_CLOCK_100MHz		100000000
> +/* RK3568 T22 COMBO PHY REG */
> +#define RK3568_T22_PHYREG5		0x14
> +#define T22_PHYREG5_PLL_DIV_MASK	GENMASK(7, 6)
> +#define T22_PHYREG5_PLL_DIV_SHIFT	6
> +#define T22_PHYREG5_PLL_DIV_2		1
> +
> +#define RK3568_T22_PHYREG6		0x18
> +#define T22_PHYREG6_TX_RTERM_MASK	GENMASK(7, 4)
> +#define T22_PHYREG6_TX_RTERM_SHIFT	4
> +#define T22_PHYREG6_TX_RTERM_50OHM	0x8
> +#define T22_PHYREG6_RX_RTERM_MASK	GENMASK(3, 0)
> +#define T22_PHYREG6_RX_RTERM_SHIFT	0
> +#define T22_PHYREG6_RX_RTERM_44OHM	0xF
> +
> +#define RK3568_T22_PHYREG7		0x1C
> +#define T22_PHYREG7_SSC_EN		BIT(4)
> +
> +#define RK3568_T22_PHYREG10		0x28
> +#define T22_PHYREG10_SU_TRIM_0_7	0xF0
> +
> +#define RK3568_T22_PHYREG11		0x2C
> +#define T22_PHYREG11_PLL_LPF_ADJ	0x4
> +
> +#define RK3568_T22_PHYREG12		0x30
> +#define T22_PHYREG12_RESISTER_MASK	GENMASK(5, 4)
> +#define T22_PHYREG12_RESISTER_SHIFT	0x4
> +#define T22_PHYREG12_RESISTER_HIGH_Z	0x3
> +#define T22_PHYREG12_CKRCV_AMP0		BIT(7)
> +
> +#define RK3568_T22_PHYREG13		0x34
> +#define T22_PHYREG13_CKRCV_AMP1		BIT(0)
> +
> +#define RK3568_T22_PHYREG14		0x38
> +#define T22_PHYREG14_CTLE_EN		BIT(0)
> +#define T22_PHYREG14_SSC_CNT_MASK	GENMASK(7, 6)
> +#define T22_PHYREG14_SSC_CNT_SHIFT	6
> +#define T22_PHYREG14_SSC_CNT_VALUE	0x1
> +
> +#define RK3568_T22_PHYREG15		0x3C
> +#define T22_PHYREG15_SSC_CNT_VALUE	0x5f
> +
> +#define RK3568_T22_PHYREG17		0x44
> +#define T22_PHYREG17_PLL_LOOP		0x32
> +
> +#define RK3568_T22_PHYREG31		0x7C
> +#define T22_PHYREG31_SSC_MASK		GENMASK(7, 4)
> +#define T22_PHYREG31_SSC_DIR_SHIFT	4
> +#define T22_PHYREG31_SSC_UPWARD		0
> +#define T22_PHYREG31_SSC_DOWNWARD	1
> +#define T22_PHYREG31_SSC_OFFSET_SHIFT	6
> +#define T22_PHYREG31_SSC_OFFSET_500PPM	1
> +
> +#define RK3568_T22_PHYREG32		0x80
> +#define T22_PHYREG32_PLL_KVCO_MASK	GENMASK(4, 2)
> +#define T22_PHYREG32_PLL_KVCO_SHIFT	2
> +#define T22_PHYREG32_PLL_KVCO_VALUE	2
> +
> +struct rockchip_combphy_priv;
> +
> +struct combphy_reg {
> +	u16 offset;
> +	u16 bitend;
> +	u16 bitstart;
> +	u16 disable;
> +	u16 enable;
> +};
> +
> +struct rockchip_combphy_grfcfg {
> +	struct combphy_reg pcie_mode_set;
> +	struct combphy_reg usb_mode_set;
> +	struct combphy_reg sgmii_mode_set;
> +	struct combphy_reg qsgmii_mode_set;
> +	struct combphy_reg pipe_rxterm_set;
> +	struct combphy_reg pipe_txelec_set;
> +	struct combphy_reg pipe_txcomp_set;
> +	struct combphy_reg pipe_clk_25m;
> +	struct combphy_reg pipe_clk_100m;
> +	struct combphy_reg pipe_phymode_sel;
> +	struct combphy_reg pipe_rate_sel;
> +	struct combphy_reg pipe_rxterm_sel;
> +	struct combphy_reg pipe_txelec_sel;
> +	struct combphy_reg pipe_txcomp_sel;
> +	struct combphy_reg pipe_clk_ext;
> +	struct combphy_reg pipe_sel_usb;
> +	struct combphy_reg pipe_sel_qsgmii;
> +	struct combphy_reg pipe_phy_status;
> +	struct combphy_reg con0_for_pcie;
> +	struct combphy_reg con1_for_pcie;
> +	struct combphy_reg con2_for_pcie;
> +	struct combphy_reg con3_for_pcie;
> +	struct combphy_reg con0_for_sata;
> +	struct combphy_reg con1_for_sata;
> +	struct combphy_reg con2_for_sata;
> +	struct combphy_reg con3_for_sata;
> +	struct combphy_reg pipe_con0_for_sata;
> +	struct combphy_reg pipe_sgmii_mac_sel;
> +	struct combphy_reg pipe_xpcs_phy_ready;
> +	struct combphy_reg u3otg0_port_en;
> +	struct combphy_reg u3otg1_port_en;
> +};
> +
> +struct rockchip_combphy_cfg {
> +	const int num_clks;
> +	const struct clk_bulk_data *clks;
> +	const struct rockchip_combphy_grfcfg *grfcfg;
> +	int (*combphy_cfg)(struct rockchip_combphy_priv *priv);
> +};
> +
> +struct rockchip_combphy_priv {
> +	u8 mode;
> +	void __iomem *mmio;
> +	int num_clks;
> +	struct clk_bulk_data *clks;
> +	struct device *dev;
> +	struct regmap *pipe_grf;
> +	struct regmap *phy_grf;
> +	struct phy *phy;
> +	struct reset_control *phy_rst;
> +	const struct rockchip_combphy_cfg *cfg;
> +};
> +
> +static inline bool param_read(struct regmap *base,
> +			      const struct combphy_reg *reg, u32 val)
> +{
> +	int ret;
> +	u32 mask, orig, tmp;
> +
> +	ret = regmap_read(base, reg->offset, &orig);
> +	if (ret)
> +		return false;
> +
> +	mask = GENMASK(reg->bitend, reg->bitstart);
> +	tmp = (orig & mask) >> reg->bitstart;
> +
> +	return tmp == val;
> +}
> +
> +static int param_write(struct regmap *base,
> +		       const struct combphy_reg *reg, bool en)
> +{
> +	u32 val, mask, tmp;
> +
> +	tmp = en ? reg->enable : reg->disable;
> +	mask = GENMASK(reg->bitend, reg->bitstart);
> +	val = (tmp << reg->bitstart) | (mask << BIT_WRITEABLE_SHIFT);
> +
> +	return regmap_write(base, reg->offset, val);
> +}
> +
> +static u32 rockchip_combphy_is_ready(struct rockchip_combphy_priv *priv)
> +{
> +	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> +	u32 mask, val;
> +
> +	mask = GENMASK(cfg->pipe_phy_status.bitend,
> +		       cfg->pipe_phy_status.bitstart);
> +
> +	regmap_read(priv->phy_grf, cfg->pipe_phy_status.offset, &val);
> +	val = (val & mask) >> cfg->pipe_phy_status.bitstart;
> +
> +	return val;
> +}
> +
> +static int rockchip_combphy_set_mode(struct rockchip_combphy_priv *priv)
> +{
> +	int ret = 0;
> +
> +	switch (priv->mode) {
> +	case PHY_TYPE_PCIE:
> +	case PHY_TYPE_USB3:
> +	case PHY_TYPE_SATA:
> +	case PHY_TYPE_SGMII:
> +	case PHY_TYPE_QSGMII:
> +		if (priv->cfg->combphy_cfg)
> +			ret = priv->cfg->combphy_cfg(priv);
> +		break;
> +	default:
> +		dev_err(priv->dev, "incompatible PHY type\n");
> +		return -EINVAL;
> +	}
> +
> +	if (ret)
> +		dev_err(priv->dev, "failed to init phy for phy mode %x\n", priv->mode);
> +
> +	return ret;
> +}
> +
> +static int rockchip_combphy_init(struct phy *phy)
> +{
> +	struct rockchip_combphy_priv *priv = phy_get_drvdata(phy);
> +	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> +	u32 val;
> +	int ret;
> +
> +	ret = clk_bulk_prepare_enable(priv->num_clks, priv->clks);
> +	if (ret) {
> +		dev_err(priv->dev, "failed to enable clks\n");
> +		return ret;
> +	}
> +
> +	ret = rockchip_combphy_set_mode(priv);
> +	if (ret)
> +		goto err_clk;
> +
> +	ret = reset_control_deassert(priv->phy_rst);
> +	if (ret)
> +		goto err_clk;
> +
> +	if (priv->mode == PHY_TYPE_USB3) {
> +		ret = readx_poll_timeout_atomic(rockchip_combphy_is_ready,
> +						priv, val,
> +						val == cfg->pipe_phy_status.enable,
> +						10, 1000);
> +		if (ret)
> +			dev_warn(priv->dev, "wait phy status ready timeout\n");
> +	}
> +
> +	return 0;
> +
> +err_clk:
> +	clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
> +
> +	return ret;
> +}
> +
> +static int rockchip_combphy_exit(struct phy *phy)
> +{
> +	struct rockchip_combphy_priv *priv = phy_get_drvdata(phy);
> +
> +	clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
> +	reset_control_assert(priv->phy_rst);
> +
> +	return 0;
> +}
> +
> +static const struct phy_ops rochchip_combphy_ops = {
> +	.init = rockchip_combphy_init,
> +	.exit = rockchip_combphy_exit,
> +	.owner = THIS_MODULE,
> +};
> +
> +static struct phy *rockchip_combphy_xlate(struct device *dev,
> +					  struct of_phandle_args *args)
> +{
> +	struct rockchip_combphy_priv *priv = dev_get_drvdata(dev);
> +
> +	if (args->args_count != 1) {
> +		dev_err(dev, "invalid number of arguments\n");
> +		return ERR_PTR(-EINVAL);
> +	}
> +
> +	if (priv->mode != PHY_NONE && priv->mode != args->args[0])
> +		dev_warn(dev, "phy type select %d overwriting type %d\n",
> +			 args->args[0], priv->mode);
> +
> +	priv->mode = args->args[0];
> +
> +	return priv->phy;
> +}
> +
> +static int rockchip_combphy_parse_dt(struct device *dev,
> +				     struct rockchip_combphy_priv *priv)
> +{
> +	const struct rockchip_combphy_cfg *phy_cfg = priv->cfg;
> +	int ret, mac_id;
> +
> +	ret = devm_clk_bulk_get(dev, priv->num_clks, priv->clks);
> +	if (ret == -EPROBE_DEFER)
> +		return -EPROBE_DEFER;
> +	if (ret)
> +		priv->num_clks = 0;
> +
> +	priv->pipe_grf = syscon_regmap_lookup_by_phandle(dev->of_node,
> +							 "rockchip,pipe-grf");
> +	if (IS_ERR(priv->pipe_grf)) {
> +		dev_err(dev, "failed to find peri_ctrl pipe-grf regmap\n");
> +		return PTR_ERR(priv->pipe_grf);
> +	}
> +
> +	priv->phy_grf = syscon_regmap_lookup_by_phandle(dev->of_node,
> +							"rockchip,pipe-phy-grf");
> +	if (IS_ERR(priv->phy_grf)) {
> +		dev_err(dev, "failed to find peri_ctrl pipe-phy-grf regmap\n");
> +		return PTR_ERR(priv->phy_grf);
> +	}
> +
> +	if (device_property_present(dev, "rockchip,dis-u3otg0-port"))
> +		param_write(priv->pipe_grf, &phy_cfg->grfcfg->u3otg0_port_en,
> +			    false);
> +	else if (device_property_present(dev, "rockchip,dis-u3otg1-port"))
> +		param_write(priv->pipe_grf, &phy_cfg->grfcfg->u3otg1_port_en,
> +			    false);
> +
> +	if (!device_property_read_u32(dev, "rockchip,sgmii-mac-sel", &mac_id) &&
> +	    (mac_id > 0))
> +		param_write(priv->pipe_grf, &phy_cfg->grfcfg->pipe_sgmii_mac_sel, true);
> +
> +	priv->phy_rst = devm_reset_control_get_optional_exclusive(dev, "combphy");
> +	if (IS_ERR(priv->phy_rst))
> +		return dev_err_probe(dev, PTR_ERR(priv->phy_rst), "failed to get phy reset\n");
> +
> +	return 0;
> +}
> +
> +static int rockchip_combphy_probe(struct platform_device *pdev)
> +{
> +	struct phy_provider *phy_provider;
> +	struct device *dev = &pdev->dev;
> +	struct rockchip_combphy_priv *priv;
> +	const struct rockchip_combphy_cfg *phy_cfg;
> +	struct resource *res;
> +	int ret;
> +
> +	phy_cfg = of_device_get_match_data(dev);
> +	if (!phy_cfg) {
> +		dev_err(dev, "No OF match data provided\n");
> +		return -EINVAL;
> +	}
> +
> +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	priv->mmio = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
> +	if (IS_ERR(priv->mmio)) {
> +		ret = PTR_ERR(priv->mmio);
> +		return ret;
> +	}
> +
> +	priv->num_clks = phy_cfg->num_clks;
> +
> +	priv->clks = devm_kmemdup(dev, phy_cfg->clks,
> +				  phy_cfg->num_clks * sizeof(struct clk_bulk_data),
> +				  GFP_KERNEL);
> +
> +	if (!priv->clks)
> +		return -ENOMEM;
> +
> +	priv->dev = dev;
> +	priv->mode = PHY_NONE;
> +	priv->cfg = phy_cfg;
> +
> +	ret = rockchip_combphy_parse_dt(dev, priv);
> +	if (ret)
> +		return ret;
> +
> +	ret = reset_control_assert(priv->phy_rst);
> +	if (ret) {
> +		dev_err(dev, "failed to reset phy\n");
> +		return ret;
> +	}
> +
> +	priv->phy = devm_phy_create(dev, NULL, &rochchip_combphy_ops);
> +	if (IS_ERR(priv->phy)) {
> +		dev_err(dev, "failed to create combphy\n");
> +		return PTR_ERR(priv->phy);
> +	}
> +
> +	dev_set_drvdata(dev, priv);
> +	phy_set_drvdata(priv->phy, priv);
> +
> +	phy_provider = devm_of_phy_provider_register(dev, rockchip_combphy_xlate);
> +
> +	return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
> +{
> +	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> +	struct clk *refclk = NULL;
> +	unsigned long rate;
> +	int i;
> +	u32 val;
> +
> +	/* Configure PHY reference clock frequency */
> +	for (i = 0; i < priv->num_clks; i++) {
> +		if (!strncmp(priv->clks[i].id, "ref", 3)) {
> +			refclk = priv->clks[i].clk;
> +			break;
> +		}
> +	}
> +
> +	if (!refclk) {
> +		dev_err(priv->dev, "No refclk found\n");
> +		return -EINVAL;
> +	}
> +
> +	switch (priv->mode) {
> +	case PHY_TYPE_PCIE:
> +		/* Set SSC downward spread spectrum */
> +		val = readl(priv->mmio + RK3568_T22_PHYREG31);
> +		val &= ~T22_PHYREG31_SSC_MASK;
> +		val |= T22_PHYREG31_SSC_DOWNWARD << T22_PHYREG31_SSC_DIR_SHIFT;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG31);
> +
> +		param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
> +		param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
> +		param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
> +		param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
> +		break;
> +	case PHY_TYPE_USB3:
> +		/* Set SSC downward spread spectrum */
> +		val = readl(priv->mmio + RK3568_T22_PHYREG31);
> +		val &= ~T22_PHYREG31_SSC_MASK;
> +		val |= T22_PHYREG31_SSC_DOWNWARD << T22_PHYREG31_SSC_DIR_SHIFT;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG31);
> +
> +		/* Enable adaptive CTLE for USB3.0 Rx */
> +		val = readl(priv->mmio + RK3568_T22_PHYREG14);
> +		val |= T22_PHYREG14_CTLE_EN;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG14);
> +
> +		/* Set PLL KVCO fine tuning signals */
> +		val = readl(priv->mmio + RK3568_T22_PHYREG32);
> +		val &= ~T22_PHYREG32_PLL_KVCO_MASK;
> +		val |= T22_PHYREG32_PLL_KVCO_VALUE << T22_PHYREG32_PLL_KVCO_SHIFT;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG32);
> +
> +		/* Enable controlling random jitter */
> +		writel(T22_PHYREG11_PLL_LPF_ADJ, priv->mmio + RK3568_T22_PHYREG11);
> +
> +		/* Set PLL input clock divider 1/2 */
> +		val = readl(priv->mmio + RK3568_T22_PHYREG5);
> +		val &= ~T22_PHYREG5_PLL_DIV_MASK;
> +		val |= T22_PHYREG5_PLL_DIV_2 << T22_PHYREG5_PLL_DIV_SHIFT;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG5);
> +
> +		writel(T22_PHYREG17_PLL_LOOP, priv->mmio + RK3568_T22_PHYREG17);
> +		writel(T22_PHYREG10_SU_TRIM_0_7, priv->mmio + RK3568_T22_PHYREG10);
> +
> +		param_write(priv->phy_grf, &cfg->pipe_sel_usb, true);
> +		param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
> +		param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
> +		param_write(priv->phy_grf, &cfg->usb_mode_set, true);
> +		break;
> +	case PHY_TYPE_SATA:
> +		/* Enable adaptive CTLE for SATA Rx */
> +		val = readl(priv->mmio + RK3568_T22_PHYREG14);
> +		val |= T22_PHYREG14_CTLE_EN;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG14);
> +		/*
> +		 * Set tx_rterm=50ohm and rx_rterm=44ohm for SATA
> +		 * 0: 60ohm, 8: 50ohm 15: 44ohm (by step abort 1ohm)
> +		 */
> +		val = T22_PHYREG6_TX_RTERM_50OHM << T22_PHYREG6_TX_RTERM_SHIFT;
> +		val |= T22_PHYREG6_RX_RTERM_44OHM << T22_PHYREG6_RX_RTERM_SHIFT;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG6);
> +
> +		param_write(priv->phy_grf, &cfg->con0_for_sata, true);
> +		param_write(priv->phy_grf, &cfg->con1_for_sata, true);
> +		param_write(priv->phy_grf, &cfg->con2_for_sata, true);
> +		param_write(priv->phy_grf, &cfg->con3_for_sata, true);
> +		param_write(priv->pipe_grf, &cfg->pipe_con0_for_sata, true);
> +		break;
> +	case PHY_TYPE_SGMII:
> +		param_write(priv->pipe_grf, &cfg->pipe_xpcs_phy_ready, true);
> +		param_write(priv->phy_grf, &cfg->pipe_phymode_sel, true);
> +		param_write(priv->phy_grf, &cfg->pipe_sel_qsgmii, true);
> +		param_write(priv->phy_grf, &cfg->sgmii_mode_set, true);
> +		break;
> +	case PHY_TYPE_QSGMII:
> +		param_write(priv->pipe_grf, &cfg->pipe_xpcs_phy_ready, true);
> +		param_write(priv->phy_grf, &cfg->pipe_phymode_sel, true);
> +		param_write(priv->phy_grf, &cfg->pipe_rate_sel, true);
> +		param_write(priv->phy_grf, &cfg->pipe_sel_qsgmii, true);
> +		param_write(priv->phy_grf, &cfg->qsgmii_mode_set, true);
> +		break;
> +	default:
> +		dev_err(priv->dev, "incompatible PHY type\n");
> +		return -EINVAL;
> +	}
> +
> +	rate = clk_get_rate(refclk);
> +
> +	switch (rate) {
> +	case REF_CLOCK_24MHz:
> +		if (priv->mode == PHY_TYPE_USB3 || priv->mode == PHY_TYPE_SATA) {
> +			/* Set ssc_cnt[9:0]=0101111101 & 31.5KHz */
> +			val = readl(priv->mmio + RK3568_T22_PHYREG14);
> +			val &= ~T22_PHYREG14_SSC_CNT_MASK;
> +			val |= T22_PHYREG14_SSC_CNT_VALUE << T22_PHYREG14_SSC_CNT_SHIFT;
> +			writel(val, priv->mmio + RK3568_T22_PHYREG14);
> +			writel(T22_PHYREG15_SSC_CNT_VALUE, priv->mmio + RK3568_T22_PHYREG15);
> +		}
> +		break;
> +	case REF_CLOCK_25MHz:
> +		param_write(priv->phy_grf, &cfg->pipe_clk_25m, true);
> +		break;
> +	case REF_CLOCK_100MHz:
> +		param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
> +		if (priv->mode == PHY_TYPE_PCIE) {
> +			/* PLL KVCO tuning fine */
> +			val = readl(priv->mmio + RK3568_T22_PHYREG32);
> +			val &= ~T22_PHYREG32_PLL_KVCO_MASK;
> +			val |= T22_PHYREG32_PLL_KVCO_VALUE << T22_PHYREG32_PLL_KVCO_SHIFT;
> +			writel(val, priv->mmio + RK3568_T22_PHYREG32);
> +
> +			/* Enable controlling random jitter */
> +			writel(T22_PHYREG11_PLL_LPF_ADJ, priv->mmio + RK3568_T22_PHYREG11);
> +
> +			val = readl(priv->mmio + RK3568_T22_PHYREG5);
> +			val &= ~T22_PHYREG5_PLL_DIV_MASK;
> +			val |= T22_PHYREG5_PLL_DIV_2 << T22_PHYREG5_PLL_DIV_SHIFT;
> +			writel(val, priv->mmio + RK3568_T22_PHYREG5);
> +
> +			writel(T22_PHYREG17_PLL_LOOP, priv->mmio + RK3568_T22_PHYREG17);
> +			writel(T22_PHYREG10_SU_TRIM_0_7, priv->mmio + RK3568_T22_PHYREG10);
> +		} else if (priv->mode == PHY_TYPE_SATA) {
> +			/* downward spread spectrum +500ppm */
> +			val = readl(priv->mmio + RK3568_T22_PHYREG31);
> +			val &= ~T22_PHYREG31_SSC_MASK;
> +			val |= T22_PHYREG31_SSC_DOWNWARD << T22_PHYREG31_SSC_DIR_SHIFT;
> +			val |= T22_PHYREG31_SSC_OFFSET_500PPM << T22_PHYREG31_SSC_OFFSET_SHIFT;
> +			writel(val, priv->mmio + RK3568_T22_PHYREG31);
> +		}
> +		break;
> +	default:
> +		dev_err(priv->dev, "Unsupported rate: %lu\n", rate);
> +		return -EINVAL;
> +	}
> +
> +	if (device_property_read_bool(priv->dev, "rockchip,ext-refclk")) {
> +		param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
> +		if (priv->mode == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
> +			val = readl(priv->mmio + RK3568_T22_PHYREG12);
> +			val &= ~T22_PHYREG12_RESISTER_MASK;
> +			val |= T22_PHYREG12_RESISTER_HIGH_Z << T22_PHYREG12_RESISTER_SHIFT;
> +			val |= T22_PHYREG12_CKRCV_AMP0;
> +			writel(val, priv->mmio + RK3568_T22_PHYREG12);
> +
> +			val = readl(priv->mmio + RK3568_T22_PHYREG13);
> +			val |= T22_PHYREG13_CKRCV_AMP1;
> +			writel(val, priv->mmio + RK3568_T22_PHYREG13);
> +		}
> +	}
> +
> +	if (device_property_read_bool(priv->dev, "rockchip,enable-ssc")) {
> +		val = readl(priv->mmio + RK3568_T22_PHYREG7);
> +		val |= T22_PHYREG7_SSC_EN;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG7);
> +	}
> +
> +	return 0;
> +}
> +
> +static const struct rockchip_combphy_grfcfg rk3568_combphy_grfcfgs = {
> +	/* pipe-phy-grf */
> +	.pcie_mode_set		= { 0x0000, 5, 0, 0x00, 0x11 },
> +	.usb_mode_set		= { 0x0000, 5, 0, 0x00, 0x04 },
> +	.sgmii_mode_set		= { 0x0000, 5, 0, 0x00, 0x01 },
> +	.qsgmii_mode_set	= { 0x0000, 5, 0, 0x00, 0x21 },
> +	.pipe_rxterm_set	= { 0x0000, 12, 12, 0x00, 0x01 },
> +	.pipe_txelec_set	= { 0x0004, 1, 1, 0x00, 0x01 },
> +	.pipe_txcomp_set	= { 0x0004, 4, 4, 0x00, 0x01 },
> +	.pipe_clk_25m		= { 0x0004, 14, 13, 0x00, 0x01 },
> +	.pipe_clk_100m		= { 0x0004, 14, 13, 0x00, 0x02 },
> +	.pipe_phymode_sel	= { 0x0008, 1, 1, 0x00, 0x01 },
> +	.pipe_rate_sel		= { 0x0008, 2, 2, 0x00, 0x01 },
> +	.pipe_rxterm_sel	= { 0x0008, 8, 8, 0x00, 0x01 },
> +	.pipe_txelec_sel	= { 0x0008, 12, 12, 0x00, 0x01 },
> +	.pipe_txcomp_sel	= { 0x0008, 15, 15, 0x00, 0x01 },
> +	.pipe_clk_ext		= { 0x000c, 9, 8, 0x02, 0x01 },
> +	.pipe_sel_usb		= { 0x000c, 14, 13, 0x00, 0x01 },
> +	.pipe_sel_qsgmii	= { 0x000c, 15, 13, 0x00, 0x07 },
> +	.pipe_phy_status	= { 0x0034, 6, 6, 0x01, 0x00 },
> +	.con0_for_pcie		= { 0x0000, 15, 0, 0x00, 0x1000 },
> +	.con1_for_pcie		= { 0x0004, 15, 0, 0x00, 0x0000 },
> +	.con2_for_pcie		= { 0x0008, 15, 0, 0x00, 0x0101 },
> +	.con3_for_pcie		= { 0x000c, 15, 0, 0x00, 0x0200 },
> +	.con0_for_sata		= { 0x0000, 15, 0, 0x00, 0x0119 },
> +	.con1_for_sata		= { 0x0004, 15, 0, 0x00, 0x0040 },
> +	.con2_for_sata		= { 0x0008, 15, 0, 0x00, 0x80c3 },
> +	.con3_for_sata		= { 0x000c, 15, 0, 0x00, 0x4407 },
> +	/* pipe-grf */
> +	.pipe_con0_for_sata	= { 0x0000, 15, 0, 0x00, 0x2220 },
> +	.pipe_sgmii_mac_sel	= { 0x0040, 1, 1, 0x00, 0x01 },
> +	.pipe_xpcs_phy_ready	= { 0x0040, 2, 2, 0x00, 0x01 },
> +	.u3otg0_port_en		= { 0x0104, 15, 0, 0x0181, 0x1100 },
> +	.u3otg1_port_en		= { 0x0144, 15, 0, 0x0181, 0x1100 },
> +};
> +
> +static const struct clk_bulk_data rk3568_clks[] = {
> +	{ .id = "ref" },
> +	{ .id = "apb" },
> +	{ .id = "pipe" },
> +};
> +
> +static const struct rockchip_combphy_cfg rk3568_combphy_cfgs = {
> +	.num_clks	= ARRAY_SIZE(rk3568_clks),
> +	.clks		= rk3568_clks,
> +	.grfcfg		= &rk3568_combphy_grfcfgs,
> +	.combphy_cfg	= rk3568_combphy_cfg,
> +};
> +
> +static const struct of_device_id rockchip_combphy_of_match[] = {
> +	{
> +		.compatible = "rockchip,rk3568-naneng-combphy",
> +		.data = &rk3568_combphy_cfgs,
> +	},
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, rockchip_combphy_of_match);
> +
> +static struct platform_driver rockchip_combphy_driver = {
> +	.probe	= rockchip_combphy_probe,
> +	.driver = {
> +		.name = "naneng-combphy",
> +		.of_match_table = rockchip_combphy_of_match,
> +	},
> +};
> +module_platform_driver(rockchip_combphy_driver);
> +
> +MODULE_DESCRIPTION("Rockchip NANENG COMBPHY driver");
> +MODULE_LICENSE("GPL v2");
Philipp Zabel Nov. 8, 2021, 9:35 a.m. UTC | #2
On Mon, 2021-10-25 at 16:06 +0800, Yifeng Zhao wrote:
> This patch implements a combo phy driver for Rockchip SoCs
> with NaNeng IP block. This phy can be used as pcie-phy, usb3-phy,
> sata-phy or sgmii-phy.
> 
> Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
> ---
> 
> Changes in v3:
> - Using api devm_reset_control_get_optional_exclusive and dev_err_probe

Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>

regards
Philipp
Johan Jonker Nov. 14, 2021, 11:40 a.m. UTC | #3
Hi Yifeng,

Some comments. Have a look if it's useful.

On 10/25/21 10:06 AM, Yifeng Zhao wrote:
> This patch implements a combo phy driver for Rockchip SoCs
> with NaNeng IP block. This phy can be used as pcie-phy, usb3-phy,
> sata-phy or sgmii-phy.
> 
> Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
> ---
> 
> Changes in v3:
> - Using api devm_reset_control_get_optional_exclusive and dev_err_probe
> - Remove apb_rst
> - Redefine registers address
> 
> Changes in v2:
> - Using api devm_platform_get_and_ioremap_resource.
> - Modify rockchip_combphy_set_Mode.
> - Add some PHY registers definition.
> 
>  drivers/phy/rockchip/Kconfig                  |   8 +
>  drivers/phy/rockchip/Makefile                 |   1 +
>  .../rockchip/phy-rockchip-naneng-combphy.c    | 638 ++++++++++++++++++
>  3 files changed, 647 insertions(+)
>  create mode 100644 drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> 
> diff --git a/drivers/phy/rockchip/Kconfig b/drivers/phy/rockchip/Kconfig
> index e812adad7242..9022e395c056 100644
> --- a/drivers/phy/rockchip/Kconfig
> +++ b/drivers/phy/rockchip/Kconfig
> @@ -66,6 +66,14 @@ config PHY_ROCKCHIP_INNO_DSIDPHY
>  	  Enable this to support the Rockchip MIPI/LVDS/TTL PHY with
>  	  Innosilicon IP block.
>  
> +config PHY_ROCKCHIP_NANENG_COMBO_PHY
> +	tristate "Rockchip NANENG COMBO PHY Driver"
> +	depends on ARCH_ROCKCHIP && OF
> +	select GENERIC_PHY
> +	help
> +	  Enable this to support the Rockchip PCIe/USB3.0/SATA/QSGMII
> +	  combo PHY with NaNeng IP block.
> +
>  config PHY_ROCKCHIP_PCIE
>  	tristate "Rockchip PCIe PHY Driver"
>  	depends on (ARCH_ROCKCHIP && OF) || COMPILE_TEST
> diff --git a/drivers/phy/rockchip/Makefile b/drivers/phy/rockchip/Makefile
> index f0eec212b2aa..a5041efb5b8f 100644
> --- a/drivers/phy/rockchip/Makefile
> +++ b/drivers/phy/rockchip/Makefile
> @@ -6,6 +6,7 @@ obj-$(CONFIG_PHY_ROCKCHIP_INNO_CSIDPHY)	+= phy-rockchip-inno-csidphy.o
>  obj-$(CONFIG_PHY_ROCKCHIP_INNO_DSIDPHY)	+= phy-rockchip-inno-dsidphy.o
>  obj-$(CONFIG_PHY_ROCKCHIP_INNO_HDMI)	+= phy-rockchip-inno-hdmi.o
>  obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
> +obj-$(CONFIG_PHY_ROCKCHIP_NANENG_COMBO_PHY)	+= phy-rockchip-naneng-combphy.o
>  obj-$(CONFIG_PHY_ROCKCHIP_PCIE)		+= phy-rockchip-pcie.o
>  obj-$(CONFIG_PHY_ROCKCHIP_TYPEC)	+= phy-rockchip-typec.o
>  obj-$(CONFIG_PHY_ROCKCHIP_USB)		+= phy-rockchip-usb.o
> diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> new file mode 100644
> index 000000000000..e5bea21a1d35
> --- /dev/null
> +++ b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> @@ -0,0 +1,638 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Rockchip PIPE USB3.0 PCIE SATA combphy driver
> + *
> + * Copyright (C) 2021 Rockchip Electronics Co., Ltd.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/phy/phy.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include <dt-bindings/phy/phy.h>
> +
> +#define BIT_WRITEABLE_SHIFT		16
> +#define REF_CLOCK_24MHz			24000000
> +#define REF_CLOCK_25MHz			25000000
> +#define REF_CLOCK_100MHz		100000000
> +/* RK3568 T22 COMBO PHY REG */
> +#define RK3568_T22_PHYREG5		0x14
> +#define T22_PHYREG5_PLL_DIV_MASK	GENMASK(7, 6)
> +#define T22_PHYREG5_PLL_DIV_SHIFT	6
> +#define T22_PHYREG5_PLL_DIV_2		1
> +
> +#define RK3568_T22_PHYREG6		0x18
> +#define T22_PHYREG6_TX_RTERM_MASK	GENMASK(7, 4)
> +#define T22_PHYREG6_TX_RTERM_SHIFT	4
> +#define T22_PHYREG6_TX_RTERM_50OHM	0x8
> +#define T22_PHYREG6_RX_RTERM_MASK	GENMASK(3, 0)
> +#define T22_PHYREG6_RX_RTERM_SHIFT	0
> +#define T22_PHYREG6_RX_RTERM_44OHM	0xF
> +
> +#define RK3568_T22_PHYREG7		0x1C
> +#define T22_PHYREG7_SSC_EN		BIT(4)
> +
> +#define RK3568_T22_PHYREG10		0x28
> +#define T22_PHYREG10_SU_TRIM_0_7	0xF0
> +
> +#define RK3568_T22_PHYREG11		0x2C
> +#define T22_PHYREG11_PLL_LPF_ADJ	0x4
> +
> +#define RK3568_T22_PHYREG12		0x30
> +#define T22_PHYREG12_RESISTER_MASK	GENMASK(5, 4)
> +#define T22_PHYREG12_RESISTER_SHIFT	0x4
> +#define T22_PHYREG12_RESISTER_HIGH_Z	0x3
> +#define T22_PHYREG12_CKRCV_AMP0		BIT(7)
> +
> +#define RK3568_T22_PHYREG13		0x34
> +#define T22_PHYREG13_CKRCV_AMP1		BIT(0)
> +
> +#define RK3568_T22_PHYREG14		0x38
> +#define T22_PHYREG14_CTLE_EN		BIT(0)
> +#define T22_PHYREG14_SSC_CNT_MASK	GENMASK(7, 6)
> +#define T22_PHYREG14_SSC_CNT_SHIFT	6
> +#define T22_PHYREG14_SSC_CNT_VALUE	0x1
> +
> +#define RK3568_T22_PHYREG15		0x3C
> +#define T22_PHYREG15_SSC_CNT_VALUE	0x5f
> +
> +#define RK3568_T22_PHYREG17		0x44
> +#define T22_PHYREG17_PLL_LOOP		0x32
> +
> +#define RK3568_T22_PHYREG31		0x7C
> +#define T22_PHYREG31_SSC_MASK		GENMASK(7, 4)
> +#define T22_PHYREG31_SSC_DIR_SHIFT	4
> +#define T22_PHYREG31_SSC_UPWARD		0
> +#define T22_PHYREG31_SSC_DOWNWARD	1
> +#define T22_PHYREG31_SSC_OFFSET_SHIFT	6
> +#define T22_PHYREG31_SSC_OFFSET_500PPM	1
> +
> +#define RK3568_T22_PHYREG32		0x80
> +#define T22_PHYREG32_PLL_KVCO_MASK	GENMASK(4, 2)
> +#define T22_PHYREG32_PLL_KVCO_SHIFT	2
> +#define T22_PHYREG32_PLL_KVCO_VALUE	2
> +
> +struct rockchip_combphy_priv;
> +
> +struct combphy_reg {
> +	u16 offset;
> +	u16 bitend;
> +	u16 bitstart;
> +	u16 disable;
> +	u16 enable;
> +};
> +
> +struct rockchip_combphy_grfcfg {
> +	struct combphy_reg pcie_mode_set;
> +	struct combphy_reg usb_mode_set;
> +	struct combphy_reg sgmii_mode_set;
> +	struct combphy_reg qsgmii_mode_set;
> +	struct combphy_reg pipe_rxterm_set;
> +	struct combphy_reg pipe_txelec_set;
> +	struct combphy_reg pipe_txcomp_set;
> +	struct combphy_reg pipe_clk_25m;
> +	struct combphy_reg pipe_clk_100m;
> +	struct combphy_reg pipe_phymode_sel;
> +	struct combphy_reg pipe_rate_sel;
> +	struct combphy_reg pipe_rxterm_sel;
> +	struct combphy_reg pipe_txelec_sel;
> +	struct combphy_reg pipe_txcomp_sel;
> +	struct combphy_reg pipe_clk_ext;
> +	struct combphy_reg pipe_sel_usb;
> +	struct combphy_reg pipe_sel_qsgmii;
> +	struct combphy_reg pipe_phy_status;
> +	struct combphy_reg con0_for_pcie;
> +	struct combphy_reg con1_for_pcie;
> +	struct combphy_reg con2_for_pcie;
> +	struct combphy_reg con3_for_pcie;
> +	struct combphy_reg con0_for_sata;
> +	struct combphy_reg con1_for_sata;
> +	struct combphy_reg con2_for_sata;
> +	struct combphy_reg con3_for_sata;
> +	struct combphy_reg pipe_con0_for_sata;
> +	struct combphy_reg pipe_sgmii_mac_sel;
> +	struct combphy_reg pipe_xpcs_phy_ready;
> +	struct combphy_reg u3otg0_port_en;
> +	struct combphy_reg u3otg1_port_en;
> +};
> +
> +struct rockchip_combphy_cfg {
> +	const int num_clks;
> +	const struct clk_bulk_data *clks;
> +	const struct rockchip_combphy_grfcfg *grfcfg;
> +	int (*combphy_cfg)(struct rockchip_combphy_priv *priv);
> +};
> +
> +struct rockchip_combphy_priv {
> +	u8 mode;
> +	void __iomem *mmio;
> +	int num_clks;
> +	struct clk_bulk_data *clks;
> +	struct device *dev;
> +	struct regmap *pipe_grf;
> +	struct regmap *phy_grf;
> +	struct phy *phy;
> +	struct reset_control *phy_rst;

Example:

bool ext-refclk;
bool enable-ssc;

> +	const struct rockchip_combphy_cfg *cfg;
> +};
> +

> +static inline bool param_read(struct regmap *base,
> +			      const struct combphy_reg *reg, u32 val)

The function param_read() is never used! Remove.

If you still need it later then change to:

rockchip_combphy_param_read()
For FTRACE it is needed that all functions start with the same function
prefix.

> +{
> +	int ret;
> +	u32 mask, orig, tmp;
> +
> +	ret = regmap_read(base, reg->offset, &orig);
> +	if (ret)
> +		return false;
> +
> +	mask = GENMASK(reg->bitend, reg->bitstart);
> +	tmp = (orig & mask) >> reg->bitstart;
> +
> +	return tmp == val;
> +}
> +

> +static int param_write(struct regmap *base,
> +		       const struct combphy_reg *reg, bool en)

rockchip_combphy_param_write()
For FTRACE it is needed that all functions start with the same function
prefix.

> +{
> +	u32 val, mask, tmp;
> +
> +	tmp = en ? reg->enable : reg->disable;
> +	mask = GENMASK(reg->bitend, reg->bitstart);
> +	val = (tmp << reg->bitstart) | (mask << BIT_WRITEABLE_SHIFT);
> +
> +	return regmap_write(base, reg->offset, val);
> +}
> +
> +static u32 rockchip_combphy_is_ready(struct rockchip_combphy_priv *priv)
> +{
> +	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> +	u32 mask, val;
> +
> +	mask = GENMASK(cfg->pipe_phy_status.bitend,
> +		       cfg->pipe_phy_status.bitstart);
> +
> +	regmap_read(priv->phy_grf, cfg->pipe_phy_status.offset, &val);
> +	val = (val & mask) >> cfg->pipe_phy_status.bitstart;
> +
> +	return val;
> +}
> +
> +static int rockchip_combphy_set_mode(struct rockchip_combphy_priv *priv)
> +{
> +	int ret = 0;
> +
> +	switch (priv->mode) {
> +	case PHY_TYPE_PCIE:
> +	case PHY_TYPE_USB3:
> +	case PHY_TYPE_SATA:
> +	case PHY_TYPE_SGMII:
> +	case PHY_TYPE_QSGMII:
> +		if (priv->cfg->combphy_cfg)
> +			ret = priv->cfg->combphy_cfg(priv);
> +		break;
> +	default:
> +		dev_err(priv->dev, "incompatible PHY type\n");
> +		return -EINVAL;
> +	}
> +
> +	if (ret)
> +		dev_err(priv->dev, "failed to init phy for phy mode %x\n", priv->mode);
> +
> +	return ret;
> +}
> +
> +static int rockchip_combphy_init(struct phy *phy)
> +{
> +	struct rockchip_combphy_priv *priv = phy_get_drvdata(phy);
> +	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> +	u32 val;
> +	int ret;
> +
> +	ret = clk_bulk_prepare_enable(priv->num_clks, priv->clks);
> +	if (ret) {
> +		dev_err(priv->dev, "failed to enable clks\n");
> +		return ret;
> +	}
> +
> +	ret = rockchip_combphy_set_mode(priv);
> +	if (ret)
> +		goto err_clk;
> +
> +	ret = reset_control_deassert(priv->phy_rst);
> +	if (ret)
> +		goto err_clk;
> +
> +	if (priv->mode == PHY_TYPE_USB3) {
> +		ret = readx_poll_timeout_atomic(rockchip_combphy_is_ready,
> +						priv, val,
> +						val == cfg->pipe_phy_status.enable,
> +						10, 1000);
> +		if (ret)
> +			dev_warn(priv->dev, "wait phy status ready timeout\n");
> +	}
> +
> +	return 0;
> +
> +err_clk:
> +	clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
> +
> +	return ret;
> +}
> +
> +static int rockchip_combphy_exit(struct phy *phy)
> +{
> +	struct rockchip_combphy_priv *priv = phy_get_drvdata(phy);
> +
> +	clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
> +	reset_control_assert(priv->phy_rst);
> +
> +	return 0;
> +}
> +
> +static const struct phy_ops rochchip_combphy_ops = {
> +	.init = rockchip_combphy_init,
> +	.exit = rockchip_combphy_exit,
> +	.owner = THIS_MODULE,
> +};
> +
> +static struct phy *rockchip_combphy_xlate(struct device *dev,
> +					  struct of_phandle_args *args)
> +{
> +	struct rockchip_combphy_priv *priv = dev_get_drvdata(dev);
> +
> +	if (args->args_count != 1) {
> +		dev_err(dev, "invalid number of arguments\n");
> +		return ERR_PTR(-EINVAL);
> +	}
> +
> +	if (priv->mode != PHY_NONE && priv->mode != args->args[0])
> +		dev_warn(dev, "phy type select %d overwriting type %d\n",
> +			 args->args[0], priv->mode);
> +
> +	priv->mode = args->args[0];
> +
> +	return priv->phy;
> +}
> +
> +static int rockchip_combphy_parse_dt(struct device *dev,
> +				     struct rockchip_combphy_priv *priv)
> +{
> +	const struct rockchip_combphy_cfg *phy_cfg = priv->cfg;
> +	int ret, mac_id;
> +
> +	ret = devm_clk_bulk_get(dev, priv->num_clks, priv->clks);

Maybe use:

priv->num_clks = devm_clk_bulk_get_all();

/**
 * devm_clk_bulk_get_all - managed get multiple clk consumers
 * @dev: device for clock "consumer"
 * @clks: pointer to the clk_bulk_data table of consumer
 *

 * Returns a positive value for the number of clocks obtained while the
 * clock references are stored in the clk_bulk_data table in @clks field.
 * Returns 0 if there're none and a negative value if something failed.

 *
 * This helper function allows drivers to get several clk
 * consumers in one operation with management, the clks will
 * automatically be freed when the device is unbound.
 */


> +	if (ret == -EPROBE_DEFER)
> +		return -EPROBE_DEFER;
> +	if (ret)
> +		priv->num_clks = 0;

Why defer? The clocks are defined in the DT or not.

> +
> +	priv->pipe_grf = syscon_regmap_lookup_by_phandle(dev->of_node,
> +							 "rockchip,pipe-grf");
> +	if (IS_ERR(priv->pipe_grf)) {
> +		dev_err(dev, "failed to find peri_ctrl pipe-grf regmap\n");
> +		return PTR_ERR(priv->pipe_grf);
> +	}
> +
> +	priv->phy_grf = syscon_regmap_lookup_by_phandle(dev->of_node,
> +							"rockchip,pipe-phy-grf");
> +	if (IS_ERR(priv->phy_grf)) {
> +		dev_err(dev, "failed to find peri_ctrl pipe-phy-grf regmap\n");
> +		return PTR_ERR(priv->phy_grf);
> +	}
> +

device_property_read_bool(priv->ext-refclk, "rockchip,ext-refclk")

documentation?

device_property_read_bool(priv->enable-ssc, "rockchip,enable-ssc")

documentation?

> +	if (device_property_present(dev, "rockchip,dis-u3otg0-port"))

documentation?

> +		param_write(priv->pipe_grf, &phy_cfg->grfcfg->u3otg0_port_en,
> +			    false);
> +	else if (device_property_present(dev, "rockchip,dis-u3otg1-port"))

documentation?

> +		param_write(priv->pipe_grf, &phy_cfg->grfcfg->u3otg1_port_en,
> +			    false);
> +
> +	if (!device_property_read_u32(dev, "rockchip,sgmii-mac-sel", &mac_id) &&

documentation?

> +	    (mac_id > 0))
> +		param_write(priv->pipe_grf, &phy_cfg->grfcfg->pipe_sgmii_mac_sel, true)> +
> +	priv->phy_rst = devm_reset_control_get_optional_exclusive(dev, "combphy");

There are 2 resets. When the reset order does matter then use
devm_reset_control_array_get() to get the resets.
The use of reset-names is then not needed.


> +	if (IS_ERR(priv->phy_rst))
> +		return dev_err_probe(dev, PTR_ERR(priv->phy_rst), "failed to get phy reset\n");
> +
> +	return 0;
> +}
> +
> +static int rockchip_combphy_probe(struct platform_device *pdev)
> +{
> +	struct phy_provider *phy_provider;
> +	struct device *dev = &pdev->dev;
> +	struct rockchip_combphy_priv *priv;
> +	const struct rockchip_combphy_cfg *phy_cfg;
> +	struct resource *res;
> +	int ret;
> +
> +	phy_cfg = of_device_get_match_data(dev);
> +	if (!phy_cfg) {
> +		dev_err(dev, "No OF match data provided\n");
> +		return -EINVAL;
> +	}
> +
> +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +
> +	priv->mmio = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
> +	if (IS_ERR(priv->mmio)) {
> +		ret = PTR_ERR(priv->mmio);
> +		return ret;
> +	}
> +
> +	priv->num_clks = phy_cfg->num_clks;
> +
> +	priv->clks = devm_kmemdup(dev, phy_cfg->clks,
> +				  phy_cfg->num_clks * sizeof(struct clk_bulk_data),
> +				  GFP_KERNEL);
> +
> +	if (!priv->clks)
> +		return -ENOMEM;
> +
> +	priv->dev = dev;
> +	priv->mode = PHY_NONE;
> +	priv->cfg = phy_cfg;
> +
> +	ret = rockchip_combphy_parse_dt(dev, priv);
> +	if (ret)
> +		return ret;
> +
> +	ret = reset_control_assert(priv->phy_rst);
> +	if (ret) {
> +		dev_err(dev, "failed to reset phy\n");
> +		return ret;
> +	}
> +
> +	priv->phy = devm_phy_create(dev, NULL, &rochchip_combphy_ops);
> +	if (IS_ERR(priv->phy)) {
> +		dev_err(dev, "failed to create combphy\n");
> +		return PTR_ERR(priv->phy);
> +	}
> +
> +	dev_set_drvdata(dev, priv);
> +	phy_set_drvdata(priv->phy, priv);
> +
> +	phy_provider = devm_of_phy_provider_register(dev, rockchip_combphy_xlate);
> +
> +	return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
> +{
> +	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> +	struct clk *refclk = NULL;
> +	unsigned long rate;
> +	int i;
> +	u32 val;
> +

> +	/* Configure PHY reference clock frequency */

Phrases start with a capital and end with a dot.
Fix them all.

> +	for (i = 0; i < priv->num_clks; i++) {
> +		if (!strncmp(priv->clks[i].id, "ref", 3)) {
> +			refclk = priv->clks[i].clk;
> +			break;
> +		}
> +	}
> +
> +	if (!refclk) {
> +		dev_err(priv->dev, "No refclk found\n");
> +		return -EINVAL;
> +	}
> +
> +	switch (priv->mode) {
> +	case PHY_TYPE_PCIE:
> +		/* Set SSC downward spread spectrum */
> +		val = readl(priv->mmio + RK3568_T22_PHYREG31);
> +		val &= ~T22_PHYREG31_SSC_MASK;
> +		val |= T22_PHYREG31_SSC_DOWNWARD << T22_PHYREG31_SSC_DIR_SHIFT;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG31);
> +
> +		param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
> +		param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
> +		param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
> +		param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
> +		break;
> +	case PHY_TYPE_USB3:
> +		/* Set SSC downward spread spectrum */
> +		val = readl(priv->mmio + RK3568_T22_PHYREG31);
> +		val &= ~T22_PHYREG31_SSC_MASK;
> +		val |= T22_PHYREG31_SSC_DOWNWARD << T22_PHYREG31_SSC_DIR_SHIFT;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG31);
> +
> +		/* Enable adaptive CTLE for USB3.0 Rx */
> +		val = readl(priv->mmio + RK3568_T22_PHYREG14);
> +		val |= T22_PHYREG14_CTLE_EN;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG14);
> +
> +		/* Set PLL KVCO fine tuning signals */
> +		val = readl(priv->mmio + RK3568_T22_PHYREG32);
> +		val &= ~T22_PHYREG32_PLL_KVCO_MASK;
> +		val |= T22_PHYREG32_PLL_KVCO_VALUE << T22_PHYREG32_PLL_KVCO_SHIFT;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG32);
> +
> +		/* Enable controlling random jitter */
> +		writel(T22_PHYREG11_PLL_LPF_ADJ, priv->mmio + RK3568_T22_PHYREG11);
> +
> +		/* Set PLL input clock divider 1/2 */
> +		val = readl(priv->mmio + RK3568_T22_PHYREG5);
> +		val &= ~T22_PHYREG5_PLL_DIV_MASK;
> +		val |= T22_PHYREG5_PLL_DIV_2 << T22_PHYREG5_PLL_DIV_SHIFT;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG5);
> +
> +		writel(T22_PHYREG17_PLL_LOOP, priv->mmio + RK3568_T22_PHYREG17);
> +		writel(T22_PHYREG10_SU_TRIM_0_7, priv->mmio + RK3568_T22_PHYREG10);
> +
> +		param_write(priv->phy_grf, &cfg->pipe_sel_usb, true);
> +		param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
> +		param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
> +		param_write(priv->phy_grf, &cfg->usb_mode_set, true);
> +		break;
> +	case PHY_TYPE_SATA:
> +		/* Enable adaptive CTLE for SATA Rx */
> +		val = readl(priv->mmio + RK3568_T22_PHYREG14);
> +		val |= T22_PHYREG14_CTLE_EN;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG14);
> +		/*
> +		 * Set tx_rterm=50ohm and rx_rterm=44ohm for SATA
> +		 * 0: 60ohm, 8: 50ohm 15: 44ohm (by step abort 1ohm)
> +		 */
> +		val = T22_PHYREG6_TX_RTERM_50OHM << T22_PHYREG6_TX_RTERM_SHIFT;
> +		val |= T22_PHYREG6_RX_RTERM_44OHM << T22_PHYREG6_RX_RTERM_SHIFT;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG6);
> +
> +		param_write(priv->phy_grf, &cfg->con0_for_sata, true);
> +		param_write(priv->phy_grf, &cfg->con1_for_sata, true);
> +		param_write(priv->phy_grf, &cfg->con2_for_sata, true);
> +		param_write(priv->phy_grf, &cfg->con3_for_sata, true);
> +		param_write(priv->pipe_grf, &cfg->pipe_con0_for_sata, true);
> +		break;
> +	case PHY_TYPE_SGMII:
> +		param_write(priv->pipe_grf, &cfg->pipe_xpcs_phy_ready, true);
> +		param_write(priv->phy_grf, &cfg->pipe_phymode_sel, true);
> +		param_write(priv->phy_grf, &cfg->pipe_sel_qsgmii, true);
> +		param_write(priv->phy_grf, &cfg->sgmii_mode_set, true);
> +		break;
> +	case PHY_TYPE_QSGMII:
> +		param_write(priv->pipe_grf, &cfg->pipe_xpcs_phy_ready, true);
> +		param_write(priv->phy_grf, &cfg->pipe_phymode_sel, true);
> +		param_write(priv->phy_grf, &cfg->pipe_rate_sel, true);
> +		param_write(priv->phy_grf, &cfg->pipe_sel_qsgmii, true);
> +		param_write(priv->phy_grf, &cfg->qsgmii_mode_set, true);
> +		break;
> +	default:
> +		dev_err(priv->dev, "incompatible PHY type\n");
> +		return -EINVAL;
> +	}
> +
> +	rate = clk_get_rate(refclk);
> +
> +	switch (rate) {
> +	case REF_CLOCK_24MHz:
> +		if (priv->mode == PHY_TYPE_USB3 || priv->mode == PHY_TYPE_SATA) {
> +			/* Set ssc_cnt[9:0]=0101111101 & 31.5KHz */
> +			val = readl(priv->mmio + RK3568_T22_PHYREG14);
> +			val &= ~T22_PHYREG14_SSC_CNT_MASK;
> +			val |= T22_PHYREG14_SSC_CNT_VALUE << T22_PHYREG14_SSC_CNT_SHIFT;
> +			writel(val, priv->mmio + RK3568_T22_PHYREG14);
> +			writel(T22_PHYREG15_SSC_CNT_VALUE, priv->mmio + RK3568_T22_PHYREG15);
> +		}
> +		break;
> +	case REF_CLOCK_25MHz:
> +		param_write(priv->phy_grf, &cfg->pipe_clk_25m, true);
> +		break;
> +	case REF_CLOCK_100MHz:
> +		param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
> +		if (priv->mode == PHY_TYPE_PCIE) {
> +			/* PLL KVCO tuning fine */
> +			val = readl(priv->mmio + RK3568_T22_PHYREG32);
> +			val &= ~T22_PHYREG32_PLL_KVCO_MASK;
> +			val |= T22_PHYREG32_PLL_KVCO_VALUE << T22_PHYREG32_PLL_KVCO_SHIFT;
> +			writel(val, priv->mmio + RK3568_T22_PHYREG32);
> +
> +			/* Enable controlling random jitter */
> +			writel(T22_PHYREG11_PLL_LPF_ADJ, priv->mmio + RK3568_T22_PHYREG11);
> +
> +			val = readl(priv->mmio + RK3568_T22_PHYREG5);
> +			val &= ~T22_PHYREG5_PLL_DIV_MASK;
> +			val |= T22_PHYREG5_PLL_DIV_2 << T22_PHYREG5_PLL_DIV_SHIFT;
> +			writel(val, priv->mmio + RK3568_T22_PHYREG5);
> +
> +			writel(T22_PHYREG17_PLL_LOOP, priv->mmio + RK3568_T22_PHYREG17);
> +			writel(T22_PHYREG10_SU_TRIM_0_7, priv->mmio + RK3568_T22_PHYREG10);
> +		} else if (priv->mode == PHY_TYPE_SATA) {
> +			/* downward spread spectrum +500ppm */
> +			val = readl(priv->mmio + RK3568_T22_PHYREG31);
> +			val &= ~T22_PHYREG31_SSC_MASK;
> +			val |= T22_PHYREG31_SSC_DOWNWARD << T22_PHYREG31_SSC_DIR_SHIFT;
> +			val |= T22_PHYREG31_SSC_OFFSET_500PPM << T22_PHYREG31_SSC_OFFSET_SHIFT;
> +			writel(val, priv->mmio + RK3568_T22_PHYREG31);
> +		}
> +		break;
> +	default:
> +		dev_err(priv->dev, "Unsupported rate: %lu\n", rate);
> +		return -EINVAL;
> +	}
> +

> +	if (device_property_read_bool(priv->dev, "rockchip,ext-refclk")) {

Example:
priv->ext-refclk

Use a variable in priv. Move all parsing in one place to
rockchip_combphy_parse_dt().

> +		param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
> +		if (priv->mode == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
> +			val = readl(priv->mmio + RK3568_T22_PHYREG12);
> +			val &= ~T22_PHYREG12_RESISTER_MASK;
> +			val |= T22_PHYREG12_RESISTER_HIGH_Z << T22_PHYREG12_RESISTER_SHIFT;
> +			val |= T22_PHYREG12_CKRCV_AMP0;
> +			writel(val, priv->mmio + RK3568_T22_PHYREG12);
> +
> +			val = readl(priv->mmio + RK3568_T22_PHYREG13);
> +			val |= T22_PHYREG13_CKRCV_AMP1;
> +			writel(val, priv->mmio + RK3568_T22_PHYREG13);
> +		}
> +	}
> +

> +	if (device_property_read_bool(priv->dev, "rockchip,enable-ssc")) {

Example:
priv->enable-ssc

Use a variable in priv. Move all parsing to rockchip_combphy_parse_dt().

> +		val = readl(priv->mmio + RK3568_T22_PHYREG7);
> +		val |= T22_PHYREG7_SSC_EN;
> +		writel(val, priv->mmio + RK3568_T22_PHYREG7);
> +	}
> +
> +	return 0;
> +}
> +
> +static const struct rockchip_combphy_grfcfg rk3568_combphy_grfcfgs = {
> +	/* pipe-phy-grf */
> +	.pcie_mode_set		= { 0x0000, 5, 0, 0x00, 0x11 },
> +	.usb_mode_set		= { 0x0000, 5, 0, 0x00, 0x04 },
> +	.sgmii_mode_set		= { 0x0000, 5, 0, 0x00, 0x01 },
> +	.qsgmii_mode_set	= { 0x0000, 5, 0, 0x00, 0x21 },
> +	.pipe_rxterm_set	= { 0x0000, 12, 12, 0x00, 0x01 },
> +	.pipe_txelec_set	= { 0x0004, 1, 1, 0x00, 0x01 },
> +	.pipe_txcomp_set	= { 0x0004, 4, 4, 0x00, 0x01 },
> +	.pipe_clk_25m		= { 0x0004, 14, 13, 0x00, 0x01 },
> +	.pipe_clk_100m		= { 0x0004, 14, 13, 0x00, 0x02 },
> +	.pipe_phymode_sel	= { 0x0008, 1, 1, 0x00, 0x01 },
> +	.pipe_rate_sel		= { 0x0008, 2, 2, 0x00, 0x01 },
> +	.pipe_rxterm_sel	= { 0x0008, 8, 8, 0x00, 0x01 },
> +	.pipe_txelec_sel	= { 0x0008, 12, 12, 0x00, 0x01 },
> +	.pipe_txcomp_sel	= { 0x0008, 15, 15, 0x00, 0x01 },
> +	.pipe_clk_ext		= { 0x000c, 9, 8, 0x02, 0x01 },
> +	.pipe_sel_usb		= { 0x000c, 14, 13, 0x00, 0x01 },
> +	.pipe_sel_qsgmii	= { 0x000c, 15, 13, 0x00, 0x07 },
> +	.pipe_phy_status	= { 0x0034, 6, 6, 0x01, 0x00 },
> +	.con0_for_pcie		= { 0x0000, 15, 0, 0x00, 0x1000 },
> +	.con1_for_pcie		= { 0x0004, 15, 0, 0x00, 0x0000 },
> +	.con2_for_pcie		= { 0x0008, 15, 0, 0x00, 0x0101 },
> +	.con3_for_pcie		= { 0x000c, 15, 0, 0x00, 0x0200 },
> +	.con0_for_sata		= { 0x0000, 15, 0, 0x00, 0x0119 },
> +	.con1_for_sata		= { 0x0004, 15, 0, 0x00, 0x0040 },
> +	.con2_for_sata		= { 0x0008, 15, 0, 0x00, 0x80c3 },
> +	.con3_for_sata		= { 0x000c, 15, 0, 0x00, 0x4407 },
> +	/* pipe-grf */
> +	.pipe_con0_for_sata	= { 0x0000, 15, 0, 0x00, 0x2220 },
> +	.pipe_sgmii_mac_sel	= { 0x0040, 1, 1, 0x00, 0x01 },
> +	.pipe_xpcs_phy_ready	= { 0x0040, 2, 2, 0x00, 0x01 },
> +	.u3otg0_port_en		= { 0x0104, 15, 0, 0x0181, 0x1100 },
> +	.u3otg1_port_en		= { 0x0144, 15, 0, 0x0181, 0x1100 },
> +};
> +

> +static const struct clk_bulk_data rk3568_clks[] = {
> +	{ .id = "ref" },
> +	{ .id = "apb" },
> +	{ .id = "pipe" },
> +};

Don't waste memory to recreate a complete const structure only to add a id.

> +
> +static const struct rockchip_combphy_cfg rk3568_combphy_cfgs = {

> +	.num_clks	= ARRAY_SIZE(rk3568_clks),
> +	.clks		= rk3568_clks,

Maybe remove. Already defined in DT.

> +	.grfcfg		= &rk3568_combphy_grfcfgs,
> +	.combphy_cfg	= rk3568_combphy_cfg,
> +};
> +
> +static const struct of_device_id rockchip_combphy_of_match[] = {
> +	{
> +		.compatible = "rockchip,rk3568-naneng-combphy",
> +		.data = &rk3568_combphy_cfgs,
> +	},
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, rockchip_combphy_of_match);
> +
> +static struct platform_driver rockchip_combphy_driver = {
> +	.probe	= rockchip_combphy_probe,
> +	.driver = {

> +		.name = "naneng-combphy",

Maybe use:
rockchip-naneng-combphy

This shows up for example in the kernel log.
Keep it in line with the other Rockchip drivers.

> +		.of_match_table = rockchip_combphy_of_match,
> +	},
> +};
> +module_platform_driver(rockchip_combphy_driver);
> +
> +MODULE_DESCRIPTION("Rockchip NANENG COMBPHY driver");
> +MODULE_LICENSE("GPL v2");
>
Johan Jonker Dec. 7, 2021, 1:51 p.m. UTC | #4
Hi,

See question below.

On 11/14/21 12:40 PM, Johan Jonker wrote:
> Hi Yifeng,
> 
> Some comments. Have a look if it's useful.
> 
> On 10/25/21 10:06 AM, Yifeng Zhao wrote:
>> This patch implements a combo phy driver for Rockchip SoCs
>> with NaNeng IP block. This phy can be used as pcie-phy, usb3-phy,
>> sata-phy or sgmii-phy.
>>
>> Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
>> ---

>> diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c

>> +
>> +#define BIT_WRITEABLE_SHIFT		16
>> +#define REF_CLOCK_24MHz			24000000
>> +#define REF_CLOCK_25MHz			25000000
>> +#define REF_CLOCK_100MHz		100000000
>> +/* RK3568 T22 COMBO PHY REG */
>> +#define RK3568_T22_PHYREG5		0x14
>> +#define T22_PHYREG5_PLL_DIV_MASK	GENMASK(7, 6)
>> +#define T22_PHYREG5_PLL_DIV_SHIFT	6
>> +#define T22_PHYREG5_PLL_DIV_2		1
>> +

>> +#define RK3568_T22_PHYREG6		0x18

Multi-PHY_Register007
Address: Operational Base + offset (0x0018)

>> +#define T22_PHYREG6_TX_RTERM_MASK	GENMASK(7, 4)
>> +#define T22_PHYREG6_TX_RTERM_SHIFT	4
>> +#define T22_PHYREG6_TX_RTERM_50OHM	0x8
>> +#define T22_PHYREG6_RX_RTERM_MASK	GENMASK(3, 0)
>> +#define T22_PHYREG6_RX_RTERM_SHIFT	0
>> +#define T22_PHYREG6_RX_RTERM_44OHM	0xF
>> +
>> +#define RK3568_T22_PHYREG7		0x1C

Multi-PHY_Register008
Address: Operational Base + offset (0x001C)

>> +#define T22_PHYREG7_SSC_EN		BIT(4)

See Rockchip RK3568 TRM Part2 V1.0-20210111 page 1957-1958

It looks as if all PHYREG defines add -1 in value? I'm I correct here?

===

SSC_EN
In U3 and SATA mode, this bit= 1, set SSC on
In PCIE mode, this bit=0 set SSC off

      If Spread Spectrum Clocking (SSC) is used it is
      required that a common reference clock is used by the link partners.
      Most commercially available platforms with PCIe backplanes use
      SSC to reduce EMI.

Maybe a dumb question for in a possible YAML description:
Is this above text from the TRM correct?
Is SSC only used in combination with PCIE instead of U3 and SATA?

===

Johan

>> +
>> +#define RK3568_T22_PHYREG10		0x28
>> +#define T22_PHYREG10_SU_TRIM_0_7	0xF0
>> +
>> +#define RK3568_T22_PHYREG11		0x2C
>> +#define T22_PHYREG11_PLL_LPF_ADJ	0x4
>> +

>> +#define RK3568_T22_PHYREG12		0x30

Multi-PHY_Register013
Address: Operational Base + offset (0x0030)

>> +#define T22_PHYREG12_RESISTER_MASK	GENMASK(5, 4)
>> +#define T22_PHYREG12_RESISTER_SHIFT	0x4
>> +#define T22_PHYREG12_RESISTER_HIGH_Z	0x3
>> +#define T22_PHYREG12_CKRCV_AMP0		BIT(7)
>> +
>> +#define RK3568_T22_PHYREG13		0x34
>> +#define T22_PHYREG13_CKRCV_AMP1		BIT(0)
>> +
>> +#define RK3568_T22_PHYREG14		0x38
>> +#define T22_PHYREG14_CTLE_EN		BIT(0)
>> +#define T22_PHYREG14_SSC_CNT_MASK	GENMASK(7, 6)
>> +#define T22_PHYREG14_SSC_CNT_SHIFT	6
>> +#define T22_PHYREG14_SSC_CNT_VALUE	0x1
>> +
>> +#define RK3568_T22_PHYREG15		0x3C
>> +#define T22_PHYREG15_SSC_CNT_VALUE	0x5f
>> +
>> +#define RK3568_T22_PHYREG17		0x44
>> +#define T22_PHYREG17_PLL_LOOP		0x32
>> +
>> +#define RK3568_T22_PHYREG31		0x7C
>> +#define T22_PHYREG31_SSC_MASK		GENMASK(7, 4)
>> +#define T22_PHYREG31_SSC_DIR_SHIFT	4
>> +#define T22_PHYREG31_SSC_UPWARD		0
>> +#define T22_PHYREG31_SSC_DOWNWARD	1
>> +#define T22_PHYREG31_SSC_OFFSET_SHIFT	6
>> +#define T22_PHYREG31_SSC_OFFSET_500PPM	1
>> +
>> +#define RK3568_T22_PHYREG32		0x80
>> +#define T22_PHYREG32_PLL_KVCO_MASK	GENMASK(4, 2)
>> +#define T22_PHYREG32_PLL_KVCO_SHIFT	2
>> +#define T22_PHYREG32_PLL_KVCO_VALUE	2
>> +
Yifeng Zhao Dec. 10, 2021, 9:52 a.m. UTC | #5
Hi Johan,

We refer to the IP documents only  and don't notice that the TRM names the registers is different. 

About the SSC, ssc_en = 1, In PCIE mode will set SSC ON, it the same with SATA and USB. 
The document description is not clear enough.





>Hi,



>



>See question below.



>



>On 11/14/21 12:40 PM, Johan Jonker wrote:



>> Hi Yifeng,



>> 



>> Some comments. Have a look if it's useful.



>> 



>> On 10/25/21 10:06 AM, Yifeng Zhao wrote:



>>> This patch implements a combo phy driver for Rockchip SoCs



>>> with NaNeng IP block. This phy can be used as pcie-phy, usb3-phy,



>>> sata-phy or sgmii-phy.



>>>



>>> Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>



>>> ---



>



>>> diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c



>



>>> +



>>> +#define BIT_WRITEABLE_SHIFT		16



>>> +#define REF_CLOCK_24MHz			24000000



>>> +#define REF_CLOCK_25MHz			25000000



>>> +#define REF_CLOCK_100MHz		100000000



>>> +/* RK3568 T22 COMBO PHY REG */



>>> +#define RK3568_T22_PHYREG5		0x14



>>> +#define T22_PHYREG5_PLL_DIV_MASK	GENMASK(7, 6)



>>> +#define T22_PHYREG5_PLL_DIV_SHIFT	6



>>> +#define T22_PHYREG5_PLL_DIV_2		1



>>> +



>



>>> +#define RK3568_T22_PHYREG6		0x18



>



>Multi-PHY_Register007



>Address: Operational Base + offset (0x0018)



>



>>> +#define T22_PHYREG6_TX_RTERM_MASK	GENMASK(7, 4)



>>> +#define T22_PHYREG6_TX_RTERM_SHIFT	4



>>> +#define T22_PHYREG6_TX_RTERM_50OHM	0x8



>>> +#define T22_PHYREG6_RX_RTERM_MASK	GENMASK(3, 0)



>>> +#define T22_PHYREG6_RX_RTERM_SHIFT	0



>>> +#define T22_PHYREG6_RX_RTERM_44OHM	0xF



>>> +



>>> +#define RK3568_T22_PHYREG7		0x1C



>



>Multi-PHY_Register008



>Address: Operational Base + offset (0x001C)



>



>>> +#define T22_PHYREG7_SSC_EN		BIT(4)



>



>See Rockchip RK3568 TRM Part2 V1.0-20210111 page 1957-1958



>



>It looks as if all PHYREG defines add -1 in value? I'm I correct here?



>



>===



>



>SSC_EN



>In U3 and SATA mode, this bit= 1, set SSC on



>In PCIE mode, this bit=0 set SSC off



>



>      If Spread Spectrum Clocking (SSC) is used it is



>      required that a common reference clock is used by the link partners.



>      Most commercially available platforms with PCIe backplanes use



>      SSC to reduce EMI.



>



>Maybe a dumb question for in a possible YAML description:



>Is this above text from the TRM correct?



>Is SSC only used in combination with PCIE instead of U3 and SATA?



>



>===



>



>Johan



>



>>> +



>>> +#define RK3568_T22_PHYREG10		0x28



>>> +#define T22_PHYREG10_SU_TRIM_0_7	0xF0



>>> +



>>> +#define RK3568_T22_PHYREG11		0x2C



>>> +#define T22_PHYREG11_PLL_LPF_ADJ	0x4



>>> +



>



>>> +#define RK3568_T22_PHYREG12		0x30



>



>Multi-PHY_Register013



>Address: Operational Base + offset (0x0030)



>



>>> +#define T22_PHYREG12_RESISTER_MASK	GENMASK(5, 4)



>>> +#define T22_PHYREG12_RESISTER_SHIFT	0x4



>>> +#define T22_PHYREG12_RESISTER_HIGH_Z	0x3



>>> +#define T22_PHYREG12_CKRCV_AMP0		BIT(7)



>>> +



>>> +#define RK3568_T22_PHYREG13		0x34



>>> +#define T22_PHYREG13_CKRCV_AMP1		BIT(0)



>>> +



>>> +#define RK3568_T22_PHYREG14		0x38



>>> +#define T22_PHYREG14_CTLE_EN		BIT(0)



>>> +#define T22_PHYREG14_SSC_CNT_MASK	GENMASK(7, 6)



>>> +#define T22_PHYREG14_SSC_CNT_SHIFT	6



>>> +#define T22_PHYREG14_SSC_CNT_VALUE	0x1



>>> +



>>> +#define RK3568_T22_PHYREG15		0x3C



>>> +#define T22_PHYREG15_SSC_CNT_VALUE	0x5f



>>> +



>>> +#define RK3568_T22_PHYREG17		0x44



>>> +#define T22_PHYREG17_PLL_LOOP		0x32



>>> +



>>> +#define RK3568_T22_PHYREG31		0x7C



>>> +#define T22_PHYREG31_SSC_MASK		GENMASK(7, 4)



>>> +#define T22_PHYREG31_SSC_DIR_SHIFT	4



>>> +#define T22_PHYREG31_SSC_UPWARD		0



>>> +#define T22_PHYREG31_SSC_DOWNWARD	1



>>> +#define T22_PHYREG31_SSC_OFFSET_SHIFT	6



>>> +#define T22_PHYREG31_SSC_OFFSET_500PPM	1



>>> +



>>> +#define RK3568_T22_PHYREG32		0x80



>>> +#define T22_PHYREG32_PLL_KVCO_MASK	GENMASK(4, 2)



>>> +#define T22_PHYREG32_PLL_KVCO_SHIFT	2



>>> +#define T22_PHYREG32_PLL_KVCO_VALUE	2



>>> +



>



>



>
diff mbox series

Patch

diff --git a/drivers/phy/rockchip/Kconfig b/drivers/phy/rockchip/Kconfig
index e812adad7242..9022e395c056 100644
--- a/drivers/phy/rockchip/Kconfig
+++ b/drivers/phy/rockchip/Kconfig
@@ -66,6 +66,14 @@  config PHY_ROCKCHIP_INNO_DSIDPHY
 	  Enable this to support the Rockchip MIPI/LVDS/TTL PHY with
 	  Innosilicon IP block.
 
+config PHY_ROCKCHIP_NANENG_COMBO_PHY
+	tristate "Rockchip NANENG COMBO PHY Driver"
+	depends on ARCH_ROCKCHIP && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the Rockchip PCIe/USB3.0/SATA/QSGMII
+	  combo PHY with NaNeng IP block.
+
 config PHY_ROCKCHIP_PCIE
 	tristate "Rockchip PCIe PHY Driver"
 	depends on (ARCH_ROCKCHIP && OF) || COMPILE_TEST
diff --git a/drivers/phy/rockchip/Makefile b/drivers/phy/rockchip/Makefile
index f0eec212b2aa..a5041efb5b8f 100644
--- a/drivers/phy/rockchip/Makefile
+++ b/drivers/phy/rockchip/Makefile
@@ -6,6 +6,7 @@  obj-$(CONFIG_PHY_ROCKCHIP_INNO_CSIDPHY)	+= phy-rockchip-inno-csidphy.o
 obj-$(CONFIG_PHY_ROCKCHIP_INNO_DSIDPHY)	+= phy-rockchip-inno-dsidphy.o
 obj-$(CONFIG_PHY_ROCKCHIP_INNO_HDMI)	+= phy-rockchip-inno-hdmi.o
 obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
+obj-$(CONFIG_PHY_ROCKCHIP_NANENG_COMBO_PHY)	+= phy-rockchip-naneng-combphy.o
 obj-$(CONFIG_PHY_ROCKCHIP_PCIE)		+= phy-rockchip-pcie.o
 obj-$(CONFIG_PHY_ROCKCHIP_TYPEC)	+= phy-rockchip-typec.o
 obj-$(CONFIG_PHY_ROCKCHIP_USB)		+= phy-rockchip-usb.o
diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
new file mode 100644
index 000000000000..e5bea21a1d35
--- /dev/null
+++ b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
@@ -0,0 +1,638 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Rockchip PIPE USB3.0 PCIE SATA combphy driver
+ *
+ * Copyright (C) 2021 Rockchip Electronics Co., Ltd.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <dt-bindings/phy/phy.h>
+
+#define BIT_WRITEABLE_SHIFT		16
+#define REF_CLOCK_24MHz			24000000
+#define REF_CLOCK_25MHz			25000000
+#define REF_CLOCK_100MHz		100000000
+/* RK3568 T22 COMBO PHY REG */
+#define RK3568_T22_PHYREG5		0x14
+#define T22_PHYREG5_PLL_DIV_MASK	GENMASK(7, 6)
+#define T22_PHYREG5_PLL_DIV_SHIFT	6
+#define T22_PHYREG5_PLL_DIV_2		1
+
+#define RK3568_T22_PHYREG6		0x18
+#define T22_PHYREG6_TX_RTERM_MASK	GENMASK(7, 4)
+#define T22_PHYREG6_TX_RTERM_SHIFT	4
+#define T22_PHYREG6_TX_RTERM_50OHM	0x8
+#define T22_PHYREG6_RX_RTERM_MASK	GENMASK(3, 0)
+#define T22_PHYREG6_RX_RTERM_SHIFT	0
+#define T22_PHYREG6_RX_RTERM_44OHM	0xF
+
+#define RK3568_T22_PHYREG7		0x1C
+#define T22_PHYREG7_SSC_EN		BIT(4)
+
+#define RK3568_T22_PHYREG10		0x28
+#define T22_PHYREG10_SU_TRIM_0_7	0xF0
+
+#define RK3568_T22_PHYREG11		0x2C
+#define T22_PHYREG11_PLL_LPF_ADJ	0x4
+
+#define RK3568_T22_PHYREG12		0x30
+#define T22_PHYREG12_RESISTER_MASK	GENMASK(5, 4)
+#define T22_PHYREG12_RESISTER_SHIFT	0x4
+#define T22_PHYREG12_RESISTER_HIGH_Z	0x3
+#define T22_PHYREG12_CKRCV_AMP0		BIT(7)
+
+#define RK3568_T22_PHYREG13		0x34
+#define T22_PHYREG13_CKRCV_AMP1		BIT(0)
+
+#define RK3568_T22_PHYREG14		0x38
+#define T22_PHYREG14_CTLE_EN		BIT(0)
+#define T22_PHYREG14_SSC_CNT_MASK	GENMASK(7, 6)
+#define T22_PHYREG14_SSC_CNT_SHIFT	6
+#define T22_PHYREG14_SSC_CNT_VALUE	0x1
+
+#define RK3568_T22_PHYREG15		0x3C
+#define T22_PHYREG15_SSC_CNT_VALUE	0x5f
+
+#define RK3568_T22_PHYREG17		0x44
+#define T22_PHYREG17_PLL_LOOP		0x32
+
+#define RK3568_T22_PHYREG31		0x7C
+#define T22_PHYREG31_SSC_MASK		GENMASK(7, 4)
+#define T22_PHYREG31_SSC_DIR_SHIFT	4
+#define T22_PHYREG31_SSC_UPWARD		0
+#define T22_PHYREG31_SSC_DOWNWARD	1
+#define T22_PHYREG31_SSC_OFFSET_SHIFT	6
+#define T22_PHYREG31_SSC_OFFSET_500PPM	1
+
+#define RK3568_T22_PHYREG32		0x80
+#define T22_PHYREG32_PLL_KVCO_MASK	GENMASK(4, 2)
+#define T22_PHYREG32_PLL_KVCO_SHIFT	2
+#define T22_PHYREG32_PLL_KVCO_VALUE	2
+
+struct rockchip_combphy_priv;
+
+struct combphy_reg {
+	u16 offset;
+	u16 bitend;
+	u16 bitstart;
+	u16 disable;
+	u16 enable;
+};
+
+struct rockchip_combphy_grfcfg {
+	struct combphy_reg pcie_mode_set;
+	struct combphy_reg usb_mode_set;
+	struct combphy_reg sgmii_mode_set;
+	struct combphy_reg qsgmii_mode_set;
+	struct combphy_reg pipe_rxterm_set;
+	struct combphy_reg pipe_txelec_set;
+	struct combphy_reg pipe_txcomp_set;
+	struct combphy_reg pipe_clk_25m;
+	struct combphy_reg pipe_clk_100m;
+	struct combphy_reg pipe_phymode_sel;
+	struct combphy_reg pipe_rate_sel;
+	struct combphy_reg pipe_rxterm_sel;
+	struct combphy_reg pipe_txelec_sel;
+	struct combphy_reg pipe_txcomp_sel;
+	struct combphy_reg pipe_clk_ext;
+	struct combphy_reg pipe_sel_usb;
+	struct combphy_reg pipe_sel_qsgmii;
+	struct combphy_reg pipe_phy_status;
+	struct combphy_reg con0_for_pcie;
+	struct combphy_reg con1_for_pcie;
+	struct combphy_reg con2_for_pcie;
+	struct combphy_reg con3_for_pcie;
+	struct combphy_reg con0_for_sata;
+	struct combphy_reg con1_for_sata;
+	struct combphy_reg con2_for_sata;
+	struct combphy_reg con3_for_sata;
+	struct combphy_reg pipe_con0_for_sata;
+	struct combphy_reg pipe_sgmii_mac_sel;
+	struct combphy_reg pipe_xpcs_phy_ready;
+	struct combphy_reg u3otg0_port_en;
+	struct combphy_reg u3otg1_port_en;
+};
+
+struct rockchip_combphy_cfg {
+	const int num_clks;
+	const struct clk_bulk_data *clks;
+	const struct rockchip_combphy_grfcfg *grfcfg;
+	int (*combphy_cfg)(struct rockchip_combphy_priv *priv);
+};
+
+struct rockchip_combphy_priv {
+	u8 mode;
+	void __iomem *mmio;
+	int num_clks;
+	struct clk_bulk_data *clks;
+	struct device *dev;
+	struct regmap *pipe_grf;
+	struct regmap *phy_grf;
+	struct phy *phy;
+	struct reset_control *phy_rst;
+	const struct rockchip_combphy_cfg *cfg;
+};
+
+static inline bool param_read(struct regmap *base,
+			      const struct combphy_reg *reg, u32 val)
+{
+	int ret;
+	u32 mask, orig, tmp;
+
+	ret = regmap_read(base, reg->offset, &orig);
+	if (ret)
+		return false;
+
+	mask = GENMASK(reg->bitend, reg->bitstart);
+	tmp = (orig & mask) >> reg->bitstart;
+
+	return tmp == val;
+}
+
+static int param_write(struct regmap *base,
+		       const struct combphy_reg *reg, bool en)
+{
+	u32 val, mask, tmp;
+
+	tmp = en ? reg->enable : reg->disable;
+	mask = GENMASK(reg->bitend, reg->bitstart);
+	val = (tmp << reg->bitstart) | (mask << BIT_WRITEABLE_SHIFT);
+
+	return regmap_write(base, reg->offset, val);
+}
+
+static u32 rockchip_combphy_is_ready(struct rockchip_combphy_priv *priv)
+{
+	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
+	u32 mask, val;
+
+	mask = GENMASK(cfg->pipe_phy_status.bitend,
+		       cfg->pipe_phy_status.bitstart);
+
+	regmap_read(priv->phy_grf, cfg->pipe_phy_status.offset, &val);
+	val = (val & mask) >> cfg->pipe_phy_status.bitstart;
+
+	return val;
+}
+
+static int rockchip_combphy_set_mode(struct rockchip_combphy_priv *priv)
+{
+	int ret = 0;
+
+	switch (priv->mode) {
+	case PHY_TYPE_PCIE:
+	case PHY_TYPE_USB3:
+	case PHY_TYPE_SATA:
+	case PHY_TYPE_SGMII:
+	case PHY_TYPE_QSGMII:
+		if (priv->cfg->combphy_cfg)
+			ret = priv->cfg->combphy_cfg(priv);
+		break;
+	default:
+		dev_err(priv->dev, "incompatible PHY type\n");
+		return -EINVAL;
+	}
+
+	if (ret)
+		dev_err(priv->dev, "failed to init phy for phy mode %x\n", priv->mode);
+
+	return ret;
+}
+
+static int rockchip_combphy_init(struct phy *phy)
+{
+	struct rockchip_combphy_priv *priv = phy_get_drvdata(phy);
+	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
+	u32 val;
+	int ret;
+
+	ret = clk_bulk_prepare_enable(priv->num_clks, priv->clks);
+	if (ret) {
+		dev_err(priv->dev, "failed to enable clks\n");
+		return ret;
+	}
+
+	ret = rockchip_combphy_set_mode(priv);
+	if (ret)
+		goto err_clk;
+
+	ret = reset_control_deassert(priv->phy_rst);
+	if (ret)
+		goto err_clk;
+
+	if (priv->mode == PHY_TYPE_USB3) {
+		ret = readx_poll_timeout_atomic(rockchip_combphy_is_ready,
+						priv, val,
+						val == cfg->pipe_phy_status.enable,
+						10, 1000);
+		if (ret)
+			dev_warn(priv->dev, "wait phy status ready timeout\n");
+	}
+
+	return 0;
+
+err_clk:
+	clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
+
+	return ret;
+}
+
+static int rockchip_combphy_exit(struct phy *phy)
+{
+	struct rockchip_combphy_priv *priv = phy_get_drvdata(phy);
+
+	clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
+	reset_control_assert(priv->phy_rst);
+
+	return 0;
+}
+
+static const struct phy_ops rochchip_combphy_ops = {
+	.init = rockchip_combphy_init,
+	.exit = rockchip_combphy_exit,
+	.owner = THIS_MODULE,
+};
+
+static struct phy *rockchip_combphy_xlate(struct device *dev,
+					  struct of_phandle_args *args)
+{
+	struct rockchip_combphy_priv *priv = dev_get_drvdata(dev);
+
+	if (args->args_count != 1) {
+		dev_err(dev, "invalid number of arguments\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	if (priv->mode != PHY_NONE && priv->mode != args->args[0])
+		dev_warn(dev, "phy type select %d overwriting type %d\n",
+			 args->args[0], priv->mode);
+
+	priv->mode = args->args[0];
+
+	return priv->phy;
+}
+
+static int rockchip_combphy_parse_dt(struct device *dev,
+				     struct rockchip_combphy_priv *priv)
+{
+	const struct rockchip_combphy_cfg *phy_cfg = priv->cfg;
+	int ret, mac_id;
+
+	ret = devm_clk_bulk_get(dev, priv->num_clks, priv->clks);
+	if (ret == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+	if (ret)
+		priv->num_clks = 0;
+
+	priv->pipe_grf = syscon_regmap_lookup_by_phandle(dev->of_node,
+							 "rockchip,pipe-grf");
+	if (IS_ERR(priv->pipe_grf)) {
+		dev_err(dev, "failed to find peri_ctrl pipe-grf regmap\n");
+		return PTR_ERR(priv->pipe_grf);
+	}
+
+	priv->phy_grf = syscon_regmap_lookup_by_phandle(dev->of_node,
+							"rockchip,pipe-phy-grf");
+	if (IS_ERR(priv->phy_grf)) {
+		dev_err(dev, "failed to find peri_ctrl pipe-phy-grf regmap\n");
+		return PTR_ERR(priv->phy_grf);
+	}
+
+	if (device_property_present(dev, "rockchip,dis-u3otg0-port"))
+		param_write(priv->pipe_grf, &phy_cfg->grfcfg->u3otg0_port_en,
+			    false);
+	else if (device_property_present(dev, "rockchip,dis-u3otg1-port"))
+		param_write(priv->pipe_grf, &phy_cfg->grfcfg->u3otg1_port_en,
+			    false);
+
+	if (!device_property_read_u32(dev, "rockchip,sgmii-mac-sel", &mac_id) &&
+	    (mac_id > 0))
+		param_write(priv->pipe_grf, &phy_cfg->grfcfg->pipe_sgmii_mac_sel, true);
+
+	priv->phy_rst = devm_reset_control_get_optional_exclusive(dev, "combphy");
+	if (IS_ERR(priv->phy_rst))
+		return dev_err_probe(dev, PTR_ERR(priv->phy_rst), "failed to get phy reset\n");
+
+	return 0;
+}
+
+static int rockchip_combphy_probe(struct platform_device *pdev)
+{
+	struct phy_provider *phy_provider;
+	struct device *dev = &pdev->dev;
+	struct rockchip_combphy_priv *priv;
+	const struct rockchip_combphy_cfg *phy_cfg;
+	struct resource *res;
+	int ret;
+
+	phy_cfg = of_device_get_match_data(dev);
+	if (!phy_cfg) {
+		dev_err(dev, "No OF match data provided\n");
+		return -EINVAL;
+	}
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->mmio = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
+	if (IS_ERR(priv->mmio)) {
+		ret = PTR_ERR(priv->mmio);
+		return ret;
+	}
+
+	priv->num_clks = phy_cfg->num_clks;
+
+	priv->clks = devm_kmemdup(dev, phy_cfg->clks,
+				  phy_cfg->num_clks * sizeof(struct clk_bulk_data),
+				  GFP_KERNEL);
+
+	if (!priv->clks)
+		return -ENOMEM;
+
+	priv->dev = dev;
+	priv->mode = PHY_NONE;
+	priv->cfg = phy_cfg;
+
+	ret = rockchip_combphy_parse_dt(dev, priv);
+	if (ret)
+		return ret;
+
+	ret = reset_control_assert(priv->phy_rst);
+	if (ret) {
+		dev_err(dev, "failed to reset phy\n");
+		return ret;
+	}
+
+	priv->phy = devm_phy_create(dev, NULL, &rochchip_combphy_ops);
+	if (IS_ERR(priv->phy)) {
+		dev_err(dev, "failed to create combphy\n");
+		return PTR_ERR(priv->phy);
+	}
+
+	dev_set_drvdata(dev, priv);
+	phy_set_drvdata(priv->phy, priv);
+
+	phy_provider = devm_of_phy_provider_register(dev, rockchip_combphy_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
+{
+	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
+	struct clk *refclk = NULL;
+	unsigned long rate;
+	int i;
+	u32 val;
+
+	/* Configure PHY reference clock frequency */
+	for (i = 0; i < priv->num_clks; i++) {
+		if (!strncmp(priv->clks[i].id, "ref", 3)) {
+			refclk = priv->clks[i].clk;
+			break;
+		}
+	}
+
+	if (!refclk) {
+		dev_err(priv->dev, "No refclk found\n");
+		return -EINVAL;
+	}
+
+	switch (priv->mode) {
+	case PHY_TYPE_PCIE:
+		/* Set SSC downward spread spectrum */
+		val = readl(priv->mmio + RK3568_T22_PHYREG31);
+		val &= ~T22_PHYREG31_SSC_MASK;
+		val |= T22_PHYREG31_SSC_DOWNWARD << T22_PHYREG31_SSC_DIR_SHIFT;
+		writel(val, priv->mmio + RK3568_T22_PHYREG31);
+
+		param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
+		param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
+		param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
+		param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
+		break;
+	case PHY_TYPE_USB3:
+		/* Set SSC downward spread spectrum */
+		val = readl(priv->mmio + RK3568_T22_PHYREG31);
+		val &= ~T22_PHYREG31_SSC_MASK;
+		val |= T22_PHYREG31_SSC_DOWNWARD << T22_PHYREG31_SSC_DIR_SHIFT;
+		writel(val, priv->mmio + RK3568_T22_PHYREG31);
+
+		/* Enable adaptive CTLE for USB3.0 Rx */
+		val = readl(priv->mmio + RK3568_T22_PHYREG14);
+		val |= T22_PHYREG14_CTLE_EN;
+		writel(val, priv->mmio + RK3568_T22_PHYREG14);
+
+		/* Set PLL KVCO fine tuning signals */
+		val = readl(priv->mmio + RK3568_T22_PHYREG32);
+		val &= ~T22_PHYREG32_PLL_KVCO_MASK;
+		val |= T22_PHYREG32_PLL_KVCO_VALUE << T22_PHYREG32_PLL_KVCO_SHIFT;
+		writel(val, priv->mmio + RK3568_T22_PHYREG32);
+
+		/* Enable controlling random jitter */
+		writel(T22_PHYREG11_PLL_LPF_ADJ, priv->mmio + RK3568_T22_PHYREG11);
+
+		/* Set PLL input clock divider 1/2 */
+		val = readl(priv->mmio + RK3568_T22_PHYREG5);
+		val &= ~T22_PHYREG5_PLL_DIV_MASK;
+		val |= T22_PHYREG5_PLL_DIV_2 << T22_PHYREG5_PLL_DIV_SHIFT;
+		writel(val, priv->mmio + RK3568_T22_PHYREG5);
+
+		writel(T22_PHYREG17_PLL_LOOP, priv->mmio + RK3568_T22_PHYREG17);
+		writel(T22_PHYREG10_SU_TRIM_0_7, priv->mmio + RK3568_T22_PHYREG10);
+
+		param_write(priv->phy_grf, &cfg->pipe_sel_usb, true);
+		param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
+		param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
+		param_write(priv->phy_grf, &cfg->usb_mode_set, true);
+		break;
+	case PHY_TYPE_SATA:
+		/* Enable adaptive CTLE for SATA Rx */
+		val = readl(priv->mmio + RK3568_T22_PHYREG14);
+		val |= T22_PHYREG14_CTLE_EN;
+		writel(val, priv->mmio + RK3568_T22_PHYREG14);
+		/*
+		 * Set tx_rterm=50ohm and rx_rterm=44ohm for SATA
+		 * 0: 60ohm, 8: 50ohm 15: 44ohm (by step abort 1ohm)
+		 */
+		val = T22_PHYREG6_TX_RTERM_50OHM << T22_PHYREG6_TX_RTERM_SHIFT;
+		val |= T22_PHYREG6_RX_RTERM_44OHM << T22_PHYREG6_RX_RTERM_SHIFT;
+		writel(val, priv->mmio + RK3568_T22_PHYREG6);
+
+		param_write(priv->phy_grf, &cfg->con0_for_sata, true);
+		param_write(priv->phy_grf, &cfg->con1_for_sata, true);
+		param_write(priv->phy_grf, &cfg->con2_for_sata, true);
+		param_write(priv->phy_grf, &cfg->con3_for_sata, true);
+		param_write(priv->pipe_grf, &cfg->pipe_con0_for_sata, true);
+		break;
+	case PHY_TYPE_SGMII:
+		param_write(priv->pipe_grf, &cfg->pipe_xpcs_phy_ready, true);
+		param_write(priv->phy_grf, &cfg->pipe_phymode_sel, true);
+		param_write(priv->phy_grf, &cfg->pipe_sel_qsgmii, true);
+		param_write(priv->phy_grf, &cfg->sgmii_mode_set, true);
+		break;
+	case PHY_TYPE_QSGMII:
+		param_write(priv->pipe_grf, &cfg->pipe_xpcs_phy_ready, true);
+		param_write(priv->phy_grf, &cfg->pipe_phymode_sel, true);
+		param_write(priv->phy_grf, &cfg->pipe_rate_sel, true);
+		param_write(priv->phy_grf, &cfg->pipe_sel_qsgmii, true);
+		param_write(priv->phy_grf, &cfg->qsgmii_mode_set, true);
+		break;
+	default:
+		dev_err(priv->dev, "incompatible PHY type\n");
+		return -EINVAL;
+	}
+
+	rate = clk_get_rate(refclk);
+
+	switch (rate) {
+	case REF_CLOCK_24MHz:
+		if (priv->mode == PHY_TYPE_USB3 || priv->mode == PHY_TYPE_SATA) {
+			/* Set ssc_cnt[9:0]=0101111101 & 31.5KHz */
+			val = readl(priv->mmio + RK3568_T22_PHYREG14);
+			val &= ~T22_PHYREG14_SSC_CNT_MASK;
+			val |= T22_PHYREG14_SSC_CNT_VALUE << T22_PHYREG14_SSC_CNT_SHIFT;
+			writel(val, priv->mmio + RK3568_T22_PHYREG14);
+			writel(T22_PHYREG15_SSC_CNT_VALUE, priv->mmio + RK3568_T22_PHYREG15);
+		}
+		break;
+	case REF_CLOCK_25MHz:
+		param_write(priv->phy_grf, &cfg->pipe_clk_25m, true);
+		break;
+	case REF_CLOCK_100MHz:
+		param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
+		if (priv->mode == PHY_TYPE_PCIE) {
+			/* PLL KVCO tuning fine */
+			val = readl(priv->mmio + RK3568_T22_PHYREG32);
+			val &= ~T22_PHYREG32_PLL_KVCO_MASK;
+			val |= T22_PHYREG32_PLL_KVCO_VALUE << T22_PHYREG32_PLL_KVCO_SHIFT;
+			writel(val, priv->mmio + RK3568_T22_PHYREG32);
+
+			/* Enable controlling random jitter */
+			writel(T22_PHYREG11_PLL_LPF_ADJ, priv->mmio + RK3568_T22_PHYREG11);
+
+			val = readl(priv->mmio + RK3568_T22_PHYREG5);
+			val &= ~T22_PHYREG5_PLL_DIV_MASK;
+			val |= T22_PHYREG5_PLL_DIV_2 << T22_PHYREG5_PLL_DIV_SHIFT;
+			writel(val, priv->mmio + RK3568_T22_PHYREG5);
+
+			writel(T22_PHYREG17_PLL_LOOP, priv->mmio + RK3568_T22_PHYREG17);
+			writel(T22_PHYREG10_SU_TRIM_0_7, priv->mmio + RK3568_T22_PHYREG10);
+		} else if (priv->mode == PHY_TYPE_SATA) {
+			/* downward spread spectrum +500ppm */
+			val = readl(priv->mmio + RK3568_T22_PHYREG31);
+			val &= ~T22_PHYREG31_SSC_MASK;
+			val |= T22_PHYREG31_SSC_DOWNWARD << T22_PHYREG31_SSC_DIR_SHIFT;
+			val |= T22_PHYREG31_SSC_OFFSET_500PPM << T22_PHYREG31_SSC_OFFSET_SHIFT;
+			writel(val, priv->mmio + RK3568_T22_PHYREG31);
+		}
+		break;
+	default:
+		dev_err(priv->dev, "Unsupported rate: %lu\n", rate);
+		return -EINVAL;
+	}
+
+	if (device_property_read_bool(priv->dev, "rockchip,ext-refclk")) {
+		param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
+		if (priv->mode == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
+			val = readl(priv->mmio + RK3568_T22_PHYREG12);
+			val &= ~T22_PHYREG12_RESISTER_MASK;
+			val |= T22_PHYREG12_RESISTER_HIGH_Z << T22_PHYREG12_RESISTER_SHIFT;
+			val |= T22_PHYREG12_CKRCV_AMP0;
+			writel(val, priv->mmio + RK3568_T22_PHYREG12);
+
+			val = readl(priv->mmio + RK3568_T22_PHYREG13);
+			val |= T22_PHYREG13_CKRCV_AMP1;
+			writel(val, priv->mmio + RK3568_T22_PHYREG13);
+		}
+	}
+
+	if (device_property_read_bool(priv->dev, "rockchip,enable-ssc")) {
+		val = readl(priv->mmio + RK3568_T22_PHYREG7);
+		val |= T22_PHYREG7_SSC_EN;
+		writel(val, priv->mmio + RK3568_T22_PHYREG7);
+	}
+
+	return 0;
+}
+
+static const struct rockchip_combphy_grfcfg rk3568_combphy_grfcfgs = {
+	/* pipe-phy-grf */
+	.pcie_mode_set		= { 0x0000, 5, 0, 0x00, 0x11 },
+	.usb_mode_set		= { 0x0000, 5, 0, 0x00, 0x04 },
+	.sgmii_mode_set		= { 0x0000, 5, 0, 0x00, 0x01 },
+	.qsgmii_mode_set	= { 0x0000, 5, 0, 0x00, 0x21 },
+	.pipe_rxterm_set	= { 0x0000, 12, 12, 0x00, 0x01 },
+	.pipe_txelec_set	= { 0x0004, 1, 1, 0x00, 0x01 },
+	.pipe_txcomp_set	= { 0x0004, 4, 4, 0x00, 0x01 },
+	.pipe_clk_25m		= { 0x0004, 14, 13, 0x00, 0x01 },
+	.pipe_clk_100m		= { 0x0004, 14, 13, 0x00, 0x02 },
+	.pipe_phymode_sel	= { 0x0008, 1, 1, 0x00, 0x01 },
+	.pipe_rate_sel		= { 0x0008, 2, 2, 0x00, 0x01 },
+	.pipe_rxterm_sel	= { 0x0008, 8, 8, 0x00, 0x01 },
+	.pipe_txelec_sel	= { 0x0008, 12, 12, 0x00, 0x01 },
+	.pipe_txcomp_sel	= { 0x0008, 15, 15, 0x00, 0x01 },
+	.pipe_clk_ext		= { 0x000c, 9, 8, 0x02, 0x01 },
+	.pipe_sel_usb		= { 0x000c, 14, 13, 0x00, 0x01 },
+	.pipe_sel_qsgmii	= { 0x000c, 15, 13, 0x00, 0x07 },
+	.pipe_phy_status	= { 0x0034, 6, 6, 0x01, 0x00 },
+	.con0_for_pcie		= { 0x0000, 15, 0, 0x00, 0x1000 },
+	.con1_for_pcie		= { 0x0004, 15, 0, 0x00, 0x0000 },
+	.con2_for_pcie		= { 0x0008, 15, 0, 0x00, 0x0101 },
+	.con3_for_pcie		= { 0x000c, 15, 0, 0x00, 0x0200 },
+	.con0_for_sata		= { 0x0000, 15, 0, 0x00, 0x0119 },
+	.con1_for_sata		= { 0x0004, 15, 0, 0x00, 0x0040 },
+	.con2_for_sata		= { 0x0008, 15, 0, 0x00, 0x80c3 },
+	.con3_for_sata		= { 0x000c, 15, 0, 0x00, 0x4407 },
+	/* pipe-grf */
+	.pipe_con0_for_sata	= { 0x0000, 15, 0, 0x00, 0x2220 },
+	.pipe_sgmii_mac_sel	= { 0x0040, 1, 1, 0x00, 0x01 },
+	.pipe_xpcs_phy_ready	= { 0x0040, 2, 2, 0x00, 0x01 },
+	.u3otg0_port_en		= { 0x0104, 15, 0, 0x0181, 0x1100 },
+	.u3otg1_port_en		= { 0x0144, 15, 0, 0x0181, 0x1100 },
+};
+
+static const struct clk_bulk_data rk3568_clks[] = {
+	{ .id = "ref" },
+	{ .id = "apb" },
+	{ .id = "pipe" },
+};
+
+static const struct rockchip_combphy_cfg rk3568_combphy_cfgs = {
+	.num_clks	= ARRAY_SIZE(rk3568_clks),
+	.clks		= rk3568_clks,
+	.grfcfg		= &rk3568_combphy_grfcfgs,
+	.combphy_cfg	= rk3568_combphy_cfg,
+};
+
+static const struct of_device_id rockchip_combphy_of_match[] = {
+	{
+		.compatible = "rockchip,rk3568-naneng-combphy",
+		.data = &rk3568_combphy_cfgs,
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, rockchip_combphy_of_match);
+
+static struct platform_driver rockchip_combphy_driver = {
+	.probe	= rockchip_combphy_probe,
+	.driver = {
+		.name = "naneng-combphy",
+		.of_match_table = rockchip_combphy_of_match,
+	},
+};
+module_platform_driver(rockchip_combphy_driver);
+
+MODULE_DESCRIPTION("Rockchip NANENG COMBPHY driver");
+MODULE_LICENSE("GPL v2");