diff mbox series

[RFC,v3,4/7] phy: qcom: Add QCOM SNPS eUSB2 repeater driver

Message ID 20230202133816.4026990-5-abel.vesa@linaro.org
State Superseded
Headers show
Series sm8550: Add support for eUSB2 repeater | expand

Commit Message

Abel Vesa Feb. 2, 2023, 1:38 p.m. UTC 
PM8550B contains a eUSB2 repeater used for making the eUSB2 from
SM8550 USB 2.0 compliant. This can be modelled SW-wise as a Phy.
So add a new phy driver for it.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 drivers/phy/qualcomm/Kconfig                  |   9 +
 drivers/phy/qualcomm/Makefile                 |   1 +
 .../phy/qualcomm/phy-qcom-eusb2-repeater.c    | 278 ++++++++++++++++++
 3 files changed, 288 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c

Comments

Vinod Koul Feb. 3, 2023, 1:48 p.m. UTC | #1 
On 02-02-23, 15:38, Abel Vesa wrote:
> PM8550B contains a eUSB2 repeater used for making the eUSB2 from
> SM8550 USB 2.0 compliant. This can be modelled SW-wise as a Phy.
> So add a new phy driver for it.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>  drivers/phy/qualcomm/Kconfig                  |   9 +
>  drivers/phy/qualcomm/Makefile                 |   1 +
>  .../phy/qualcomm/phy-qcom-eusb2-repeater.c    | 278 ++++++++++++++++++
>  3 files changed, 288 insertions(+)
>  create mode 100644 drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c
> 
> diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
> index 27b5a2a3637d..a70631b04522 100644
> --- a/drivers/phy/qualcomm/Kconfig
> +++ b/drivers/phy/qualcomm/Kconfig
> @@ -79,6 +79,15 @@ config PHY_QCOM_SNPS_EUSB2
>  	  chipsets. The PHY is paired with a Synopsys DWC3 USB controller
>  	  on Qualcomm SOCs.
>  
> +config PHY_QCOM_EUSB2_REPEATER
> +	tristate "Qualcomm SNPS eUSB2 Repeater Driver"
> +	depends on OF && (ARCH_QCOM || COMPILE_TEST)
> +	select GENERIC_PHY
> +	help
> +	  Enable support for the USB high-speed SNPS eUSB2 repeater on Qualcomm
> +	  PMICs. The repeater is paired with a Synopsys eUSB2 Phy
> +	  on Qualcomm SOCs.
> +
>  config PHY_QCOM_USB_HS
>  	tristate "Qualcomm USB HS PHY module"
>  	depends on USB_ULPI_BUS
> diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
> index 3ee118f4dfc7..7dcba9537b69 100644
> --- a/drivers/phy/qualcomm/Makefile
> +++ b/drivers/phy/qualcomm/Makefile
> @@ -14,6 +14,7 @@ obj-$(CONFIG_PHY_QCOM_QMP)		+= \
>  
>  obj-$(CONFIG_PHY_QCOM_QUSB2)		+= phy-qcom-qusb2.o
>  obj-$(CONFIG_PHY_QCOM_SNPS_EUSB2)	+= phy-qcom-snps-eusb2.o
> +obj-$(CONFIG_PHY_QCOM_EUSB2_REPEATER)	+= phy-qcom-eusb2-repeater.o
>  obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
>  obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o
>  obj-$(CONFIG_PHY_QCOM_USB_HS_28NM)	+= phy-qcom-usb-hs-28nm.o
> diff --git a/drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c b/drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c
> new file mode 100644
> index 000000000000..f7f822f2973f
> --- /dev/null
> +++ b/drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c
> @@ -0,0 +1,278 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2023, Linaro Limited
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/regmap.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/phy/phy.h>
> +
> +/* eUSB2 status registers */
> +#define EUSB2_RPTR_STATUS		0x08
> +#define	RPTR_OK				BIT(7)
> +
> +/* eUSB2 control registers */
> +#define EUSB2_EN_CTL1			0x46
> +#define EUSB2_RPTR_EN			BIT(7)
> +
> +#define PHY_HOST_MODE			BIT(0)
> +#define EUSB2_FORCE_EN_5		0xE8
> +#define F_CLK_19P2M_EN			BIT(6)
> +#define F_CLK_19P2M_EN_SHIFT		6

Why use shifts, use FIELD_{PREP|GET} instead

> +
> +#define EUSB2_FORCE_VAL_5		0xED
> +#define V_CLK_19P2M_EN			BIT(6)
> +#define V_CLK_19P2M_EN_SHIFT		6
> +
> +#define EUSB2_TUNE_IUSB2		0x51
> +#define EUSB2_TUNE_SQUELCH_U		0x54
> +#define EUSB2_TUNE_USB2_PREEM		0x57
> +
> +#define QCOM_EUSB2_REPEATER_INIT_CFG(o, v)	\
> +	{					\
> +		.offset = o,			\
> +		.val = v,			\
> +	}
> +
> +enum repeater_mode {
> +	REPEATER_HOST_MODE,
> +	REPEATER_PERIPH_MODE,
> +};
> +
> +struct eusb2_repeater_init_tbl {
> +	unsigned int offset;
> +	unsigned int val;
> +};
> +
> +struct eusb2_repeater_cfg {
> +	const struct eusb2_repeater_init_tbl *init_tbl;
> +	int init_tbl_num;
> +	/* regulators to be requested */

this comments is not very useful! either drop or add a meaningful
comment

> +	const char * const *vreg_list;
> +	int num_vregs;
> +};
> +
> +struct eusb2_repeater {
> +	struct device *dev;
> +	struct regmap *regmap;
> +	struct phy *phy;
> +	struct regulator_bulk_data *vregs;
> +	const struct eusb2_repeater_cfg *cfg;
> +	u16 base;
> +	enum phy_mode mode;
> +};
> +
> +static const char * const pm8550b_vreg_l[] = {
> +	"vdd18", "vdd3",
> +};
> +
> +static const struct eusb2_repeater_init_tbl pm8550b_init_tbl[] = {
> +	QCOM_EUSB2_REPEATER_INIT_CFG(EUSB2_TUNE_IUSB2, 0x8),
> +	QCOM_EUSB2_REPEATER_INIT_CFG(EUSB2_TUNE_SQUELCH_U, 0x3),
> +	QCOM_EUSB2_REPEATER_INIT_CFG(EUSB2_TUNE_USB2_PREEM, 0x5),
> +};
> +
> +static const struct eusb2_repeater_cfg pm8550b_eusb2_cfg = {
> +	.init_tbl	= pm8550b_init_tbl,
> +	.init_tbl_num	= ARRAY_SIZE(pm8550b_init_tbl),
> +	.vreg_list	= pm8550b_vreg_l,
> +	.num_vregs	= ARRAY_SIZE(pm8550b_vreg_l),
> +};
> +
> +static int eusb2_repeater_init_vregs(struct eusb2_repeater *rptr)
> +{
> +	int num = rptr->cfg->num_vregs;
> +	struct device *dev = rptr->dev;
> +	int i;
> +
> +	rptr->vregs = devm_kcalloc(dev, num, sizeof(*rptr->vregs), GFP_KERNEL);
> +	if (!rptr->vregs)
> +		return -ENOMEM;
> +
> +	for (i = 0; i < num; i++)
> +		rptr->vregs[i].supply = rptr->cfg->vreg_list[i];
> +
> +	return devm_regulator_bulk_get(dev, num, rptr->vregs);
> +}
> +
> +static int eusb2_repeater_init(struct phy *phy)
> +{
> +	struct eusb2_repeater *rptr = phy_get_drvdata(phy);
> +	const struct eusb2_repeater_init_tbl *init_tbl = rptr->cfg->init_tbl;
> +	int num = rptr->cfg->init_tbl_num;
> +	int ret = 0;

superfluous init

> +	u32 val;
> +	int i;
> +
> +	ret = regulator_bulk_enable(rptr->cfg->num_vregs, rptr->vregs);
> +	if (ret)
> +		return ret;
> +
> +	regmap_update_bits(rptr->regmap, rptr->base + EUSB2_EN_CTL1,
> +				EUSB2_RPTR_EN, EUSB2_RPTR_EN);
> +
> +	for (i = 0; i < num; i++)
> +		regmap_update_bits(rptr->regmap,
> +					rptr->base + init_tbl[i].offset,
> +					init_tbl[i].val, init_tbl[i].val);
> +
> +	ret = regmap_read_poll_timeout(rptr->regmap,
> +					rptr->base + EUSB2_RPTR_STATUS, val,
> +					val & RPTR_OK, 10, 5);
> +	if (ret)
> +		dev_err(rptr->dev, "initialization timed-out\n");
> +
> +	return ret;
> +}
> +
> +static int eusb2_repeater_set_mode(struct phy *phy,
> +					enum phy_mode mode, int submode)
> +{
> +	struct eusb2_repeater *rptr = phy_get_drvdata(phy);
> +
> +	switch (mode) {
> +	case PHY_MODE_USB_HOST:
> +		/*
> +		 * CM.Lx is prohibited when repeater is already into Lx state as
> +		 * per eUSB 1.2 Spec. Below implement software workaround until
> +		 * PHY and controller is fixing seen observation.
> +		 */
> +		regmap_update_bits(rptr->regmap, rptr->base + EUSB2_FORCE_EN_5,
> +				F_CLK_19P2M_EN, F_CLK_19P2M_EN);

pls align to preceding open brace (hint checkpatch --strict would warn
you for this)

> +		regmap_update_bits(rptr->regmap, rptr->base + EUSB2_FORCE_VAL_5,
> +				V_CLK_19P2M_EN, V_CLK_19P2M_EN);
> +		break;
> +	case PHY_MODE_USB_DEVICE:
> +		/*
> +		 * In device mode clear host mode related workaround as there
> +		 * is no repeater reset available, and enable/disable of
> +		 * repeater doesn't clear previous value due to shared
> +		 * regulators (say host <-> device mode switch).
> +		 */
> +		regmap_update_bits(rptr->regmap, rptr->base + EUSB2_FORCE_EN_5,
> +				F_CLK_19P2M_EN, 0);
> +		regmap_update_bits(rptr->regmap, rptr->base + EUSB2_FORCE_VAL_5,
> +				V_CLK_19P2M_EN, 0);
> +		break;
> +	default:
> +		return -EINVAL;
> +	}
> +
> +	return 0;
> +}
> +
> +static int eusb2_repeater_exit(struct phy *phy)
> +{
> +	struct eusb2_repeater *rptr = phy_get_drvdata(phy);
> +
> +	return regulator_bulk_disable(rptr->cfg->num_vregs, rptr->vregs);
> +}
> +
> +
> +static const struct phy_ops eusb2_repeater_ops = {
> +	.init		= eusb2_repeater_init,
> +	.exit		= eusb2_repeater_exit,
> +	.set_mode	= eusb2_repeater_set_mode,
> +	.owner		= THIS_MODULE,
> +};
> +
> +static int eusb2_repeater_probe(struct platform_device *pdev)
> +{
> +	struct eusb2_repeater *rptr;
> +	struct device *dev = &pdev->dev;
> +	struct phy_provider *phy_provider;
> +	struct device_node *np;
> +	u32 res;
> +	int ret;
> +
> +	np = of_node_get(dev->of_node);
> +
> +	rptr = devm_kzalloc(dev, sizeof(*rptr), GFP_KERNEL);
> +	if (!rptr)
> +		goto err_node_put;
> +
> +	rptr->dev = dev;
> +	dev_set_drvdata(dev, rptr);
> +
> +	rptr->cfg = of_device_get_match_data(dev);
> +	if (!rptr->cfg)
> +		goto err_node_put;
> +
> +	rptr->regmap = dev_get_regmap(dev->parent, NULL);
> +	if (!rptr->regmap)
> +		goto err_node_put;
> +
> +	ret = of_property_read_u32(np, "reg", &res);
> +	if (ret < 0)
> +		goto err_node_put;
> +
> +	rptr->base = res;
> +
> +	ret = eusb2_repeater_init_vregs(rptr);
> +	if (ret < 0) {
> +		dev_err(dev, "unable to get supplies\n");
> +		goto err_node_put;
> +	}
> +
> +	rptr->phy = devm_phy_create(dev, np, &eusb2_repeater_ops);
> +	if (IS_ERR(rptr->phy)) {
> +		ret = PTR_ERR(rptr->phy);
> +		dev_err(dev, "failed to create PHY: %d\n", ret);
> +		goto err_node_put;
> +	}
> +
> +	phy_set_drvdata(rptr->phy, rptr);
> +
> +	of_node_put(np);
> +
> +	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +	if (IS_ERR(phy_provider))
> +		return PTR_ERR(phy_provider);
> +
> +	dev_info(dev, "Registered Qcom-eUSB2 repeater\n");
> +
> +	return 0;
> +
> +err_node_put:
> +	of_node_put(np);
> +	return ret;
> +}
> +
> +static int eusb2_repeater_remove(struct platform_device *pdev)
> +{
> +	struct eusb2_repeater *rptr = platform_get_drvdata(pdev);
> +
> +	if (!rptr)
> +		return 0;
> +
> +	eusb2_repeater_exit(rptr->phy);
> +	return 0;
> +}
> +
> +
> +static const struct of_device_id eusb2_repeater_of_match_table[] = {
> +	{
> +		.compatible = "qcom,pm8550b-eusb2-repeater",
> +		.data = &pm8550b_eusb2_cfg,
> +	},
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, eusb2_repeater_of_match_table);
> +
> +static struct platform_driver eusb2_repeater_driver = {
> +	.probe		= eusb2_repeater_probe,
> +	.remove		= eusb2_repeater_remove,
> +	.driver = {
> +		.name	= "qcom-eusb2-repeater",
> +		.of_match_table = eusb2_repeater_of_match_table,
> +	},
> +};
> +
> +module_platform_driver(eusb2_repeater_driver);
> +
> +MODULE_DESCRIPTION("Qualcomm PMIC eUSB2 Repeater driver");
> +MODULE_LICENSE("GPL v2");
> -- 
> 2.34.1
Dmitry Baryshkov Feb. 3, 2023, 4:51 p.m. UTC | #2 
On 02/02/2023 15:38, Abel Vesa wrote:
> PM8550B contains a eUSB2 repeater used for making the eUSB2 from
> SM8550 USB 2.0 compliant. This can be modelled SW-wise as a Phy.
> So add a new phy driver for it.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   drivers/phy/qualcomm/Kconfig                  |   9 +
>   drivers/phy/qualcomm/Makefile                 |   1 +
>   .../phy/qualcomm/phy-qcom-eusb2-repeater.c    | 278 ++++++++++++++++++
>   3 files changed, 288 insertions(+)
>   create mode 100644 drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c
> 
> diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
> index 27b5a2a3637d..a70631b04522 100644
> --- a/drivers/phy/qualcomm/Kconfig
> +++ b/drivers/phy/qualcomm/Kconfig
> @@ -79,6 +79,15 @@ config PHY_QCOM_SNPS_EUSB2
>   	  chipsets. The PHY is paired with a Synopsys DWC3 USB controller
>   	  on Qualcomm SOCs.
>   
> +config PHY_QCOM_EUSB2_REPEATER
> +	tristate "Qualcomm SNPS eUSB2 Repeater Driver"
> +	depends on OF && (ARCH_QCOM || COMPILE_TEST)
> +	select GENERIC_PHY
> +	help
> +	  Enable support for the USB high-speed SNPS eUSB2 repeater on Qualcomm
> +	  PMICs. The repeater is paired with a Synopsys eUSB2 Phy
> +	  on Qualcomm SOCs.
> +
>   config PHY_QCOM_USB_HS
>   	tristate "Qualcomm USB HS PHY module"
>   	depends on USB_ULPI_BUS
> diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
> index 3ee118f4dfc7..7dcba9537b69 100644
> --- a/drivers/phy/qualcomm/Makefile
> +++ b/drivers/phy/qualcomm/Makefile
> @@ -14,6 +14,7 @@ obj-$(CONFIG_PHY_QCOM_QMP)		+= \
>   
>   obj-$(CONFIG_PHY_QCOM_QUSB2)		+= phy-qcom-qusb2.o
>   obj-$(CONFIG_PHY_QCOM_SNPS_EUSB2)	+= phy-qcom-snps-eusb2.o
> +obj-$(CONFIG_PHY_QCOM_EUSB2_REPEATER)	+= phy-qcom-eusb2-repeater.o
>   obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
>   obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o
>   obj-$(CONFIG_PHY_QCOM_USB_HS_28NM)	+= phy-qcom-usb-hs-28nm.o
> diff --git a/drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c b/drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c
> new file mode 100644
> index 000000000000..f7f822f2973f
> --- /dev/null
> +++ b/drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c
> @@ -0,0 +1,278 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2023, Linaro Limited
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/regmap.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/phy/phy.h>
> +
> +/* eUSB2 status registers */
> +#define EUSB2_RPTR_STATUS		0x08
> +#define	RPTR_OK				BIT(7)
> +
> +/* eUSB2 control registers */
> +#define EUSB2_EN_CTL1			0x46
> +#define EUSB2_RPTR_EN			BIT(7)
> +
> +#define PHY_HOST_MODE			BIT(0)
> +#define EUSB2_FORCE_EN_5		0xE8
> +#define F_CLK_19P2M_EN			BIT(6)
> +#define F_CLK_19P2M_EN_SHIFT		6

Drop the _SHIFT defines please, they don't add anything on top of 
previous defines (and don't seem to be used anyway).

> +
> +#define EUSB2_FORCE_VAL_5		0xED
> +#define V_CLK_19P2M_EN			BIT(6)
> +#define V_CLK_19P2M_EN_SHIFT		6
> +
> +#define EUSB2_TUNE_IUSB2		0x51
> +#define EUSB2_TUNE_SQUELCH_U		0x54
> +#define EUSB2_TUNE_USB2_PREEM		0x57
> +
> +#define QCOM_EUSB2_REPEATER_INIT_CFG(o, v)	\
> +	{					\
> +		.offset = o,			\
> +		.val = v,			\
> +	}
> +
> +enum repeater_mode {
> +	REPEATER_HOST_MODE,
> +	REPEATER_PERIPH_MODE,
> +};

I think this is unused now.

> +
> +struct eusb2_repeater_init_tbl {
> +	unsigned int offset;
> +	unsigned int val;
> +};
> +
> +struct eusb2_repeater_cfg {
> +	const struct eusb2_repeater_init_tbl *init_tbl;
> +	int init_tbl_num;
> +	/* regulators to be requested */
> +	const char * const *vreg_list;
> +	int num_vregs;
> +};
> +
> +struct eusb2_repeater {
> +	struct device *dev;
> +	struct regmap *regmap;
> +	struct phy *phy;
> +	struct regulator_bulk_data *vregs;
> +	const struct eusb2_repeater_cfg *cfg;
> +	u16 base;
> +	enum phy_mode mode;
> +};
> +
> +static const char * const pm8550b_vreg_l[] = {
> +	"vdd18", "vdd3",
> +};
> +
> +static const struct eusb2_repeater_init_tbl pm8550b_init_tbl[] = {
> +	QCOM_EUSB2_REPEATER_INIT_CFG(EUSB2_TUNE_IUSB2, 0x8),
> +	QCOM_EUSB2_REPEATER_INIT_CFG(EUSB2_TUNE_SQUELCH_U, 0x3),
> +	QCOM_EUSB2_REPEATER_INIT_CFG(EUSB2_TUNE_USB2_PREEM, 0x5),
> +};
> +
> +static const struct eusb2_repeater_cfg pm8550b_eusb2_cfg = {
> +	.init_tbl	= pm8550b_init_tbl,
> +	.init_tbl_num	= ARRAY_SIZE(pm8550b_init_tbl),
> +	.vreg_list	= pm8550b_vreg_l,
> +	.num_vregs	= ARRAY_SIZE(pm8550b_vreg_l),
> +};
> +
> +static int eusb2_repeater_init_vregs(struct eusb2_repeater *rptr)
> +{
> +	int num = rptr->cfg->num_vregs;
> +	struct device *dev = rptr->dev;
> +	int i;
> +
> +	rptr->vregs = devm_kcalloc(dev, num, sizeof(*rptr->vregs), GFP_KERNEL);
> +	if (!rptr->vregs)
> +		return -ENOMEM;
> +
> +	for (i = 0; i < num; i++)
> +		rptr->vregs[i].supply = rptr->cfg->vreg_list[i];
> +
> +	return devm_regulator_bulk_get(dev, num, rptr->vregs);
> +}
> +
> +static int eusb2_repeater_init(struct phy *phy)
> +{
> +	struct eusb2_repeater *rptr = phy_get_drvdata(phy);
> +	const struct eusb2_repeater_init_tbl *init_tbl = rptr->cfg->init_tbl;
> +	int num = rptr->cfg->init_tbl_num;
> +	int ret = 0;
> +	u32 val;
> +	int i;
> +
> +	ret = regulator_bulk_enable(rptr->cfg->num_vregs, rptr->vregs);
> +	if (ret)
> +		return ret;
> +
> +	regmap_update_bits(rptr->regmap, rptr->base + EUSB2_EN_CTL1,
> +				EUSB2_RPTR_EN, EUSB2_RPTR_EN);
> +
> +	for (i = 0; i < num; i++)
> +		regmap_update_bits(rptr->regmap,
> +					rptr->base + init_tbl[i].offset,
> +					init_tbl[i].val, init_tbl[i].val);

I'd move this to a separate function. Then you can use it in the 
set_mode() too.

> +
> +	ret = regmap_read_poll_timeout(rptr->regmap,
> +					rptr->base + EUSB2_RPTR_STATUS, val,
> +					val & RPTR_OK, 10, 5);
> +	if (ret)
> +		dev_err(rptr->dev, "initialization timed-out\n");
> +
> +	return ret;
> +}
> +
> +static int eusb2_repeater_set_mode(struct phy *phy,
> +					enum phy_mode mode, int submode)
> +{
> +	struct eusb2_repeater *rptr = phy_get_drvdata(phy);
> +
> +	switch (mode) {
> +	case PHY_MODE_USB_HOST:
> +		/*
> +		 * CM.Lx is prohibited when repeater is already into Lx state as
> +		 * per eUSB 1.2 Spec. Below implement software workaround until
> +		 * PHY and controller is fixing seen observation.
> +		 */
> +		regmap_update_bits(rptr->regmap, rptr->base + EUSB2_FORCE_EN_5,
> +				F_CLK_19P2M_EN, F_CLK_19P2M_EN);
> +		regmap_update_bits(rptr->regmap, rptr->base + EUSB2_FORCE_VAL_5,
> +				V_CLK_19P2M_EN, V_CLK_19P2M_EN);
> +		break;
> +	case PHY_MODE_USB_DEVICE:
> +		/*
> +		 * In device mode clear host mode related workaround as there
> +		 * is no repeater reset available, and enable/disable of
> +		 * repeater doesn't clear previous value due to shared
> +		 * regulators (say host <-> device mode switch).
> +		 */
> +		regmap_update_bits(rptr->regmap, rptr->base + EUSB2_FORCE_EN_5,
> +				F_CLK_19P2M_EN, 0);
> +		regmap_update_bits(rptr->regmap, rptr->base + EUSB2_FORCE_VAL_5,
> +				V_CLK_19P2M_EN, 0);
> +		break;
> +	default:
> +		return -EINVAL;
> +	}
> +
> +	return 0;
> +}
> +
> +static int eusb2_repeater_exit(struct phy *phy)
> +{
> +	struct eusb2_repeater *rptr = phy_get_drvdata(phy);
> +
> +	return regulator_bulk_disable(rptr->cfg->num_vregs, rptr->vregs);
> +}
> +
> +
> +static const struct phy_ops eusb2_repeater_ops = {
> +	.init		= eusb2_repeater_init,
> +	.exit		= eusb2_repeater_exit,
> +	.set_mode	= eusb2_repeater_set_mode,
> +	.owner		= THIS_MODULE,
> +};
> +
> +static int eusb2_repeater_probe(struct platform_device *pdev)
> +{
> +	struct eusb2_repeater *rptr;
> +	struct device *dev = &pdev->dev;
> +	struct phy_provider *phy_provider;
> +	struct device_node *np;
> +	u32 res;
> +	int ret;
> +
> +	np = of_node_get(dev->of_node);

Do you really need to increase the refcount here? I thought that we can 
use dev->of_node straight away.

> +
> +	rptr = devm_kzalloc(dev, sizeof(*rptr), GFP_KERNEL);
> +	if (!rptr)
> +		goto err_node_put;
> +
> +	rptr->dev = dev;
> +	dev_set_drvdata(dev, rptr);
> +
> +	rptr->cfg = of_device_get_match_data(dev);
> +	if (!rptr->cfg)
> +		goto err_node_put;
> +
> +	rptr->regmap = dev_get_regmap(dev->parent, NULL);
> +	if (!rptr->regmap)
> +		goto err_node_put;
> +
> +	ret = of_property_read_u32(np, "reg", &res);
> +	if (ret < 0)
> +		goto err_node_put;
> +
> +	rptr->base = res;
> +
> +	ret = eusb2_repeater_init_vregs(rptr);
> +	if (ret < 0) {
> +		dev_err(dev, "unable to get supplies\n");
> +		goto err_node_put;
> +	}
> +
> +	rptr->phy = devm_phy_create(dev, np, &eusb2_repeater_ops);
> +	if (IS_ERR(rptr->phy)) {
> +		ret = PTR_ERR(rptr->phy);
> +		dev_err(dev, "failed to create PHY: %d\n", ret);
> +		goto err_node_put;
> +	}
> +
> +	phy_set_drvdata(rptr->phy, rptr);
> +
> +	of_node_put(np);
> +
> +	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +	if (IS_ERR(phy_provider))
> +		return PTR_ERR(phy_provider);
> +
> +	dev_info(dev, "Registered Qcom-eUSB2 repeater\n");
> +
> +	return 0;
> +
> +err_node_put:
> +	of_node_put(np);
> +	return ret;
> +}
> +
> +static int eusb2_repeater_remove(struct platform_device *pdev)
> +{
> +	struct eusb2_repeater *rptr = platform_get_drvdata(pdev);
> +
> +	if (!rptr)
> +		return 0;
> +
> +	eusb2_repeater_exit(rptr->phy);
> +	return 0;
> +}
> +
> +
> +static const struct of_device_id eusb2_repeater_of_match_table[] = {
> +	{
> +		.compatible = "qcom,pm8550b-eusb2-repeater",
> +		.data = &pm8550b_eusb2_cfg,
> +	},
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, eusb2_repeater_of_match_table);
> +
> +static struct platform_driver eusb2_repeater_driver = {
> +	.probe		= eusb2_repeater_probe,
> +	.remove		= eusb2_repeater_remove,
> +	.driver = {
> +		.name	= "qcom-eusb2-repeater",
> +		.of_match_table = eusb2_repeater_of_match_table,
> +	},
> +};
> +
> +module_platform_driver(eusb2_repeater_driver);
> +
> +MODULE_DESCRIPTION("Qualcomm PMIC eUSB2 Repeater driver");
> +MODULE_LICENSE("GPL v2");
Abel Vesa Feb. 7, 2023, 12:25 p.m. UTC | #3 
On 23-02-03 18:51:13, Dmitry Baryshkov wrote:
> On 02/02/2023 15:38, Abel Vesa wrote:
> > PM8550B contains a eUSB2 repeater used for making the eUSB2 from
> > SM8550 USB 2.0 compliant. This can be modelled SW-wise as a Phy.
> > So add a new phy driver for it.
> > 
> > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > ---
> >   drivers/phy/qualcomm/Kconfig                  |   9 +
> >   drivers/phy/qualcomm/Makefile                 |   1 +
> >   .../phy/qualcomm/phy-qcom-eusb2-repeater.c    | 278 ++++++++++++++++++
> >   3 files changed, 288 insertions(+)
> >   create mode 100644 drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c
> > 

[ ... ]

> > +
> > +static int eusb2_repeater_init(struct phy *phy)
> > +{
> > +	struct eusb2_repeater *rptr = phy_get_drvdata(phy);
> > +	const struct eusb2_repeater_init_tbl *init_tbl = rptr->cfg->init_tbl;
> > +	int num = rptr->cfg->init_tbl_num;
> > +	int ret = 0;
> > +	u32 val;
> > +	int i;
> > +
> > +	ret = regulator_bulk_enable(rptr->cfg->num_vregs, rptr->vregs);
> > +	if (ret)
> > +		return ret;
> > +
> > +	regmap_update_bits(rptr->regmap, rptr->base + EUSB2_EN_CTL1,
> > +				EUSB2_RPTR_EN, EUSB2_RPTR_EN);
> > +
> > +	for (i = 0; i < num; i++)
> > +		regmap_update_bits(rptr->regmap,
> > +					rptr->base + init_tbl[i].offset,
> > +					init_tbl[i].val, init_tbl[i].val);
> 
> I'd move this to a separate function. Then you can use it in the set_mode()
> too.
> 

I don't think this is necessary in set_mode.

> > +
> > +	ret = regmap_read_poll_timeout(rptr->regmap,
> > +					rptr->base + EUSB2_RPTR_STATUS, val,
> > +					val & RPTR_OK, 10, 5);
> > +	if (ret)
> > +		dev_err(rptr->dev, "initialization timed-out\n");
> > +
> > +	return ret;
> > +}
> > +

[ ... ]
Dmitry Baryshkov Feb. 7, 2023, 1:03 p.m. UTC | #4 
On Tue, 7 Feb 2023 at 14:25, Abel Vesa <abel.vesa@linaro.org> wrote:
>
> On 23-02-03 18:51:13, Dmitry Baryshkov wrote:
> > On 02/02/2023 15:38, Abel Vesa wrote:
> > > PM8550B contains a eUSB2 repeater used for making the eUSB2 from
> > > SM8550 USB 2.0 compliant. This can be modelled SW-wise as a Phy.
> > > So add a new phy driver for it.
> > >
> > > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > > ---
> > >   drivers/phy/qualcomm/Kconfig                  |   9 +
> > >   drivers/phy/qualcomm/Makefile                 |   1 +
> > >   .../phy/qualcomm/phy-qcom-eusb2-repeater.c    | 278 ++++++++++++++++++
> > >   3 files changed, 288 insertions(+)
> > >   create mode 100644 drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c
> > >
>
> [ ... ]
>
> > > +
> > > +static int eusb2_repeater_init(struct phy *phy)
> > > +{
> > > +   struct eusb2_repeater *rptr = phy_get_drvdata(phy);
> > > +   const struct eusb2_repeater_init_tbl *init_tbl = rptr->cfg->init_tbl;
> > > +   int num = rptr->cfg->init_tbl_num;
> > > +   int ret = 0;
> > > +   u32 val;
> > > +   int i;
> > > +
> > > +   ret = regulator_bulk_enable(rptr->cfg->num_vregs, rptr->vregs);
> > > +   if (ret)
> > > +           return ret;
> > > +
> > > +   regmap_update_bits(rptr->regmap, rptr->base + EUSB2_EN_CTL1,
> > > +                           EUSB2_RPTR_EN, EUSB2_RPTR_EN);
> > > +
> > > +   for (i = 0; i < num; i++)
> > > +           regmap_update_bits(rptr->regmap,
> > > +                                   rptr->base + init_tbl[i].offset,
> > > +                                   init_tbl[i].val, init_tbl[i].val);
> >
> > I'd move this to a separate function. Then you can use it in the set_mode()
> > too.
> >
>
> I don't think this is necessary in set_mode.

It's not necessary. However as set_mode() is also a sequence of simple
register updates, it might be easy to have everything as an
offset-mask-value table.

>
> > > +
> > > +   ret = regmap_read_poll_timeout(rptr->regmap,
> > > +                                   rptr->base + EUSB2_RPTR_STATUS, val,
> > > +                                   val & RPTR_OK, 10, 5);
> > > +   if (ret)
> > > +           dev_err(rptr->dev, "initialization timed-out\n");
> > > +
> > > +   return ret;
> > > +}
> > > +
>
> [ ... ]
Abel Vesa Feb. 7, 2023, 1:10 p.m. UTC | #5 
On 23-02-07 15:03:39, Dmitry Baryshkov wrote:
> On Tue, 7 Feb 2023 at 14:25, Abel Vesa <abel.vesa@linaro.org> wrote:
> >
> > On 23-02-03 18:51:13, Dmitry Baryshkov wrote:
> > > On 02/02/2023 15:38, Abel Vesa wrote:
> > > > PM8550B contains a eUSB2 repeater used for making the eUSB2 from
> > > > SM8550 USB 2.0 compliant. This can be modelled SW-wise as a Phy.
> > > > So add a new phy driver for it.
> > > >
> > > > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > > > ---
> > > >   drivers/phy/qualcomm/Kconfig                  |   9 +
> > > >   drivers/phy/qualcomm/Makefile                 |   1 +
> > > >   .../phy/qualcomm/phy-qcom-eusb2-repeater.c    | 278 ++++++++++++++++++
> > > >   3 files changed, 288 insertions(+)
> > > >   create mode 100644 drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c
> > > >
> >
> > [ ... ]
> >
> > > > +
> > > > +static int eusb2_repeater_init(struct phy *phy)
> > > > +{
> > > > +   struct eusb2_repeater *rptr = phy_get_drvdata(phy);
> > > > +   const struct eusb2_repeater_init_tbl *init_tbl = rptr->cfg->init_tbl;
> > > > +   int num = rptr->cfg->init_tbl_num;
> > > > +   int ret = 0;
> > > > +   u32 val;
> > > > +   int i;
> > > > +
> > > > +   ret = regulator_bulk_enable(rptr->cfg->num_vregs, rptr->vregs);
> > > > +   if (ret)
> > > > +           return ret;
> > > > +
> > > > +   regmap_update_bits(rptr->regmap, rptr->base + EUSB2_EN_CTL1,
> > > > +                           EUSB2_RPTR_EN, EUSB2_RPTR_EN);
> > > > +
> > > > +   for (i = 0; i < num; i++)
> > > > +           regmap_update_bits(rptr->regmap,
> > > > +                                   rptr->base + init_tbl[i].offset,
> > > > +                                   init_tbl[i].val, init_tbl[i].val);
> > >
> > > I'd move this to a separate function. Then you can use it in the set_mode()
> > > too.
> > >
> >
> > I don't think this is necessary in set_mode.
> 
> It's not necessary. However as set_mode() is also a sequence of simple
> register updates, it might be easy to have everything as an
> offset-mask-value table.

Yeah, but then you would reinit the repeater on set_mode, which should
not be done.

> 
> >
> > > > +
> > > > +   ret = regmap_read_poll_timeout(rptr->regmap,
> > > > +                                   rptr->base + EUSB2_RPTR_STATUS, val,
> > > > +                                   val & RPTR_OK, 10, 5);
> > > > +   if (ret)
> > > > +           dev_err(rptr->dev, "initialization timed-out\n");
> > > > +
> > > > +   return ret;
> > > > +}
> > > > +
> >
> > [ ... ]
> 
> 
> 
> -- 
> With best wishes
> Dmitry
diff mbox series

Patch

diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
index 27b5a2a3637d..a70631b04522 100644
--- a/drivers/phy/qualcomm/Kconfig
+++ b/drivers/phy/qualcomm/Kconfig
@@ -79,6 +79,15 @@  config PHY_QCOM_SNPS_EUSB2
 	  chipsets. The PHY is paired with a Synopsys DWC3 USB controller
 	  on Qualcomm SOCs.
 
+config PHY_QCOM_EUSB2_REPEATER
+	tristate "Qualcomm SNPS eUSB2 Repeater Driver"
+	depends on OF && (ARCH_QCOM || COMPILE_TEST)
+	select GENERIC_PHY
+	help
+	  Enable support for the USB high-speed SNPS eUSB2 repeater on Qualcomm
+	  PMICs. The repeater is paired with a Synopsys eUSB2 Phy
+	  on Qualcomm SOCs.
+
 config PHY_QCOM_USB_HS
 	tristate "Qualcomm USB HS PHY module"
 	depends on USB_ULPI_BUS
diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
index 3ee118f4dfc7..7dcba9537b69 100644
--- a/drivers/phy/qualcomm/Makefile
+++ b/drivers/phy/qualcomm/Makefile
@@ -14,6 +14,7 @@  obj-$(CONFIG_PHY_QCOM_QMP)		+= \
 
 obj-$(CONFIG_PHY_QCOM_QUSB2)		+= phy-qcom-qusb2.o
 obj-$(CONFIG_PHY_QCOM_SNPS_EUSB2)	+= phy-qcom-snps-eusb2.o
+obj-$(CONFIG_PHY_QCOM_EUSB2_REPEATER)	+= phy-qcom-eusb2-repeater.o
 obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
 obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o
 obj-$(CONFIG_PHY_QCOM_USB_HS_28NM)	+= phy-qcom-usb-hs-28nm.o
diff --git a/drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c b/drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c
new file mode 100644
index 000000000000..f7f822f2973f
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c
@@ -0,0 +1,278 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regmap.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+
+/* eUSB2 status registers */
+#define EUSB2_RPTR_STATUS		0x08
+#define	RPTR_OK				BIT(7)
+
+/* eUSB2 control registers */
+#define EUSB2_EN_CTL1			0x46
+#define EUSB2_RPTR_EN			BIT(7)
+
+#define PHY_HOST_MODE			BIT(0)
+#define EUSB2_FORCE_EN_5		0xE8
+#define F_CLK_19P2M_EN			BIT(6)
+#define F_CLK_19P2M_EN_SHIFT		6
+
+#define EUSB2_FORCE_VAL_5		0xED
+#define V_CLK_19P2M_EN			BIT(6)
+#define V_CLK_19P2M_EN_SHIFT		6
+
+#define EUSB2_TUNE_IUSB2		0x51
+#define EUSB2_TUNE_SQUELCH_U		0x54
+#define EUSB2_TUNE_USB2_PREEM		0x57
+
+#define QCOM_EUSB2_REPEATER_INIT_CFG(o, v)	\
+	{					\
+		.offset = o,			\
+		.val = v,			\
+	}
+
+enum repeater_mode {
+	REPEATER_HOST_MODE,
+	REPEATER_PERIPH_MODE,
+};
+
+struct eusb2_repeater_init_tbl {
+	unsigned int offset;
+	unsigned int val;
+};
+
+struct eusb2_repeater_cfg {
+	const struct eusb2_repeater_init_tbl *init_tbl;
+	int init_tbl_num;
+	/* regulators to be requested */
+	const char * const *vreg_list;
+	int num_vregs;
+};
+
+struct eusb2_repeater {
+	struct device *dev;
+	struct regmap *regmap;
+	struct phy *phy;
+	struct regulator_bulk_data *vregs;
+	const struct eusb2_repeater_cfg *cfg;
+	u16 base;
+	enum phy_mode mode;
+};
+
+static const char * const pm8550b_vreg_l[] = {
+	"vdd18", "vdd3",
+};
+
+static const struct eusb2_repeater_init_tbl pm8550b_init_tbl[] = {
+	QCOM_EUSB2_REPEATER_INIT_CFG(EUSB2_TUNE_IUSB2, 0x8),
+	QCOM_EUSB2_REPEATER_INIT_CFG(EUSB2_TUNE_SQUELCH_U, 0x3),
+	QCOM_EUSB2_REPEATER_INIT_CFG(EUSB2_TUNE_USB2_PREEM, 0x5),
+};
+
+static const struct eusb2_repeater_cfg pm8550b_eusb2_cfg = {
+	.init_tbl	= pm8550b_init_tbl,
+	.init_tbl_num	= ARRAY_SIZE(pm8550b_init_tbl),
+	.vreg_list	= pm8550b_vreg_l,
+	.num_vregs	= ARRAY_SIZE(pm8550b_vreg_l),
+};
+
+static int eusb2_repeater_init_vregs(struct eusb2_repeater *rptr)
+{
+	int num = rptr->cfg->num_vregs;
+	struct device *dev = rptr->dev;
+	int i;
+
+	rptr->vregs = devm_kcalloc(dev, num, sizeof(*rptr->vregs), GFP_KERNEL);
+	if (!rptr->vregs)
+		return -ENOMEM;
+
+	for (i = 0; i < num; i++)
+		rptr->vregs[i].supply = rptr->cfg->vreg_list[i];
+
+	return devm_regulator_bulk_get(dev, num, rptr->vregs);
+}
+
+static int eusb2_repeater_init(struct phy *phy)
+{
+	struct eusb2_repeater *rptr = phy_get_drvdata(phy);
+	const struct eusb2_repeater_init_tbl *init_tbl = rptr->cfg->init_tbl;
+	int num = rptr->cfg->init_tbl_num;
+	int ret = 0;
+	u32 val;
+	int i;
+
+	ret = regulator_bulk_enable(rptr->cfg->num_vregs, rptr->vregs);
+	if (ret)
+		return ret;
+
+	regmap_update_bits(rptr->regmap, rptr->base + EUSB2_EN_CTL1,
+				EUSB2_RPTR_EN, EUSB2_RPTR_EN);
+
+	for (i = 0; i < num; i++)
+		regmap_update_bits(rptr->regmap,
+					rptr->base + init_tbl[i].offset,
+					init_tbl[i].val, init_tbl[i].val);
+
+	ret = regmap_read_poll_timeout(rptr->regmap,
+					rptr->base + EUSB2_RPTR_STATUS, val,
+					val & RPTR_OK, 10, 5);
+	if (ret)
+		dev_err(rptr->dev, "initialization timed-out\n");
+
+	return ret;
+}
+
+static int eusb2_repeater_set_mode(struct phy *phy,
+					enum phy_mode mode, int submode)
+{
+	struct eusb2_repeater *rptr = phy_get_drvdata(phy);
+
+	switch (mode) {
+	case PHY_MODE_USB_HOST:
+		/*
+		 * CM.Lx is prohibited when repeater is already into Lx state as
+		 * per eUSB 1.2 Spec. Below implement software workaround until
+		 * PHY and controller is fixing seen observation.
+		 */
+		regmap_update_bits(rptr->regmap, rptr->base + EUSB2_FORCE_EN_5,
+				F_CLK_19P2M_EN, F_CLK_19P2M_EN);
+		regmap_update_bits(rptr->regmap, rptr->base + EUSB2_FORCE_VAL_5,
+				V_CLK_19P2M_EN, V_CLK_19P2M_EN);
+		break;
+	case PHY_MODE_USB_DEVICE:
+		/*
+		 * In device mode clear host mode related workaround as there
+		 * is no repeater reset available, and enable/disable of
+		 * repeater doesn't clear previous value due to shared
+		 * regulators (say host <-> device mode switch).
+		 */
+		regmap_update_bits(rptr->regmap, rptr->base + EUSB2_FORCE_EN_5,
+				F_CLK_19P2M_EN, 0);
+		regmap_update_bits(rptr->regmap, rptr->base + EUSB2_FORCE_VAL_5,
+				V_CLK_19P2M_EN, 0);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int eusb2_repeater_exit(struct phy *phy)
+{
+	struct eusb2_repeater *rptr = phy_get_drvdata(phy);
+
+	return regulator_bulk_disable(rptr->cfg->num_vregs, rptr->vregs);
+}
+
+
+static const struct phy_ops eusb2_repeater_ops = {
+	.init		= eusb2_repeater_init,
+	.exit		= eusb2_repeater_exit,
+	.set_mode	= eusb2_repeater_set_mode,
+	.owner		= THIS_MODULE,
+};
+
+static int eusb2_repeater_probe(struct platform_device *pdev)
+{
+	struct eusb2_repeater *rptr;
+	struct device *dev = &pdev->dev;
+	struct phy_provider *phy_provider;
+	struct device_node *np;
+	u32 res;
+	int ret;
+
+	np = of_node_get(dev->of_node);
+
+	rptr = devm_kzalloc(dev, sizeof(*rptr), GFP_KERNEL);
+	if (!rptr)
+		goto err_node_put;
+
+	rptr->dev = dev;
+	dev_set_drvdata(dev, rptr);
+
+	rptr->cfg = of_device_get_match_data(dev);
+	if (!rptr->cfg)
+		goto err_node_put;
+
+	rptr->regmap = dev_get_regmap(dev->parent, NULL);
+	if (!rptr->regmap)
+		goto err_node_put;
+
+	ret = of_property_read_u32(np, "reg", &res);
+	if (ret < 0)
+		goto err_node_put;
+
+	rptr->base = res;
+
+	ret = eusb2_repeater_init_vregs(rptr);
+	if (ret < 0) {
+		dev_err(dev, "unable to get supplies\n");
+		goto err_node_put;
+	}
+
+	rptr->phy = devm_phy_create(dev, np, &eusb2_repeater_ops);
+	if (IS_ERR(rptr->phy)) {
+		ret = PTR_ERR(rptr->phy);
+		dev_err(dev, "failed to create PHY: %d\n", ret);
+		goto err_node_put;
+	}
+
+	phy_set_drvdata(rptr->phy, rptr);
+
+	of_node_put(np);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(phy_provider))
+		return PTR_ERR(phy_provider);
+
+	dev_info(dev, "Registered Qcom-eUSB2 repeater\n");
+
+	return 0;
+
+err_node_put:
+	of_node_put(np);
+	return ret;
+}
+
+static int eusb2_repeater_remove(struct platform_device *pdev)
+{
+	struct eusb2_repeater *rptr = platform_get_drvdata(pdev);
+
+	if (!rptr)
+		return 0;
+
+	eusb2_repeater_exit(rptr->phy);
+	return 0;
+}
+
+
+static const struct of_device_id eusb2_repeater_of_match_table[] = {
+	{
+		.compatible = "qcom,pm8550b-eusb2-repeater",
+		.data = &pm8550b_eusb2_cfg,
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, eusb2_repeater_of_match_table);
+
+static struct platform_driver eusb2_repeater_driver = {
+	.probe		= eusb2_repeater_probe,
+	.remove		= eusb2_repeater_remove,
+	.driver = {
+		.name	= "qcom-eusb2-repeater",
+		.of_match_table = eusb2_repeater_of_match_table,
+	},
+};
+
+module_platform_driver(eusb2_repeater_driver);
+
+MODULE_DESCRIPTION("Qualcomm PMIC eUSB2 Repeater driver");
+MODULE_LICENSE("GPL v2");