@@ -740,9 +740,9 @@ gcc: clock-controller@100000 {
#reset-cells = <1>;
#power-domain-cells = <1>;
clocks = <&bi_tcxo_div2>, <&sleep_clk>,
- <0>,
- <0>,
- <0>,
+ <&pcie0_phy>,
+ <&pcie1_phy>,
+ <&pcie_1_phy_aux_clk>,
<&ufs_mem_phy 0>,
<&ufs_mem_phy 1>,
<&ufs_mem_phy 2>,
@@ -1641,6 +1641,197 @@ mmss_noc: interconnect@1780000 {
qcom,bcm-voters = <&apps_bcm_voter>;
};
+ pcie0: pci@1c00000 {
+ device_type = "pci";
+ compatible = "qcom,pcie-sm8550";
+ reg = <0 0x01c00000 0 0x3000>,
+ <0 0x60000000 0 0xf1d>,
+ <0 0x60000f20 0 0xa8>,
+ <0 0x60001000 0 0x1000>,
+ <0 0x60100000 0 0x100000>;
+ reg-names = "parf", "dbi", "elbi", "atu", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>,
+ <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0x3d00000>;
+ bus-range = <0x00 0xff>;
+
+ dma-coherent;
+
+ linux,pci-domain = <0>;
+ num-lanes = <2>;
+
+ interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
+ <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+ <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
+ <&gcc GCC_DDRSS_PCIE_SF_QTB_CLK>,
+ <&gcc GCC_AGGRE_NOC_PCIE_AXI_CLK>;
+ clock-names = "aux",
+ "cfg",
+ "bus_master",
+ "bus_slave",
+ "slave_q2a",
+ "ddrss_sf_tbu",
+ "noc_aggr";
+
+ interconnects = <&pcie_noc MASTER_PCIE_0 0 &mc_virt SLAVE_EBI1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc_main SLAVE_PCIE_0 0>;
+ interconnect-names = "pcie-mem", "cpu-pcie";
+
+ iommus = <&apps_smmu 0x1400 0x7f>;
+ iommu-map = <0x0 &apps_smmu 0x1400 0x1>,
+ <0x100 &apps_smmu 0x1401 0x1>;
+
+ resets = <&gcc GCC_PCIE_0_BCR>;
+ reset-names = "pci";
+
+ power-domains = <&gcc PCIE_0_GDSC>;
+
+ phys = <&pcie0_phy>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
+
+ pcie0_phy: phy@1c06000 {
+ compatible = "qcom,sm8550-qmp-gen3x2-pcie-phy";
+ reg = <0 0x01c06000 0 0x2000>;
+
+ clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
+ <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+ <&tcsr TCSR_PCIE_0_CLKREF_EN>,
+ <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>,
+ <&gcc GCC_PCIE_0_PIPE_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "rchng",
+ "pipe";
+
+ resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+ reset-names = "phy";
+
+ assigned-clocks = <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ power-domains = <&gcc PCIE_0_PHY_GDSC>;
+
+ #clock-cells = <0>;
+ clock-output-names = "pcie0_pipe_clk";
+
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ pcie1: pci@1c08000 {
+ device_type = "pci";
+ compatible = "qcom,pcie-sm8550";
+ reg = <0x0 0x01c08000 0x0 0x3000>,
+ <0x0 0x40000000 0x0 0xf1d>,
+ <0x0 0x40000f20 0x0 0xa8>,
+ <0x0 0x40001000 0x0 0x1000>,
+ <0x0 0x40100000 0x0 0x100000>;
+ reg-names = "parf", "dbi", "elbi", "atu", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges = <0x01000000 0x0 0x40200000 0 0x40200000 0x0 0x100000>,
+ <0x02000000 0x0 0x40300000 0 0x40300000 0x0 0x1fd00000>;
+ bus-range = <0x00 0xff>;
+
+ dma-coherent;
+
+ linux,pci-domain = <1>;
+ num-lanes = <2>;
+
+ interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 0 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 0 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 0 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 0 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
+ <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+ <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+ <&gcc GCC_DDRSS_PCIE_SF_QTB_CLK>,
+ <&gcc GCC_AGGRE_NOC_PCIE_AXI_CLK>,
+ <&gcc GCC_CNOC_PCIE_SF_AXI_CLK>;
+ clock-names = "aux",
+ "cfg",
+ "bus_master",
+ "bus_slave",
+ "slave_q2a",
+ "ddrss_sf_tbu",
+ "noc_aggr",
+ "cnoc_sf_axi";
+
+ assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ interconnects = <&pcie_noc MASTER_PCIE_1 0 &mc_virt SLAVE_EBI1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc_main SLAVE_PCIE_1 0>;
+ interconnect-names = "pcie-mem", "cpu-pcie";
+
+ iommus = <&apps_smmu 0x1480 0x7f>;
+ iommu-map = <0x0 &apps_smmu 0x1480 0x1>,
+ <0x100 &apps_smmu 0x1481 0x1>;
+
+ resets = <&gcc GCC_PCIE_1_BCR>,
+ <&gcc GCC_PCIE_1_LINK_DOWN_BCR>;
+ reset-names = "pci", "link_down";
+
+ power-domains = <&gcc PCIE_1_GDSC>;
+
+ phys = <&pcie1_phy>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
+
+ pcie1_phy: phy@1c0e000 {
+ compatible = "qcom,sm8550-qmp-gen4x2-pcie-phy";
+ reg = <0x0 0x01c0e000 0x0 0x2000>;
+
+ clocks = <&gcc GCC_PCIE_1_PHY_AUX_CLK>,
+ <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+ <&tcsr TCSR_PCIE_1_CLKREF_EN>,
+ <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>,
+ <&gcc GCC_PCIE_1_PIPE_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "rchng",
+ "pipe";
+
+ resets = <&gcc GCC_PCIE_1_PHY_BCR>,
+ <&gcc GCC_PCIE_1_NOCSR_COM_PHY_BCR>;
+ reset-names = "phy", "phy_nocsr";
+
+ assigned-clocks = <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ power-domains = <&gcc PCIE_1_PHY_GDSC>;
+
+ #clock-cells = <0>;
+ clock-output-names = "pcie1_pipe_clk";
+
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
cryptobam: dma-controller@1dc4000 {
compatible = "qcom,bam-v1.7.0";
reg = <0x0 0x01dc4000 0x0 0x28000>;
Add PCIe controllers and PHY nodes. Signed-off-by: Abel Vesa <abel.vesa@linaro.org> --- This patch does not have a v3, but since it is now part of the same patchset with the controller and the phy drivers patches, I had to bump the version to 4. The v5 was here: https://lore.kernel.org/all/20230202123902.3831491-12-abel.vesa@linaro.org/ Changes since v6: * dropped the perst-gpios and wake-gpios properties as they already exist in MTP dts * dropped the enable-gpios since the tlmm ID was wrong, will probably be added later along with wifi support Changes since v5: * renamed nocsr_com to phy_nocsr as discussed off-list with Bjorn and Johan Changes since v4: * renamed noc_aggr_4 back to noc_aggr * moved pinctrl properties out to MTP dts * renamed nocsr to nocsr_com Changes since v2: * renamed the pcie_1_link_down_reset to simply link_down * dropped the pipe from clock-names * renamed aggre clock-names to noc_aggr_4 * dropped the _pcie infix from cnoc_pcie_sf_axi * dropped the aux_phy clock from the pcie1 Changes since v1: * ordered pcie related nodes alphabetically in MTP dts * dropped the pipe_mux, phy_pipe and ref clocks from the pcie nodes * dropped the child node from the phy nodes, like Johan suggested, and updated to use the sc8280xp binding scheme * changed "pcie_1_nocsr_com_phy_reset" 2nd reset name of pcie1_phy to "nocsr" * reordered all pcie nodes properties to look similar to the ones from sc8280xp arch/arm64/boot/dts/qcom/sm8550.dtsi | 197 ++++++++++++++++++++++++++- 1 file changed, 194 insertions(+), 3 deletions(-)