@@ -12,6 +12,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/thermal/thermal.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
/ {
compatible = "fsl,ls1046a";
@@ -424,6 +425,116 @@ sfp: efuse@1e80000 {
clock-names = "sfp";
};
+ serdes1: serdes@1ea0000 {
+ compatible = "fsl,ls1046a-serdes", "fsl,lynx-10g";
+ reg = <0x0 0x1ea0000 0x0 0x2000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #clock-cells = <1>;
+ status = "disabled";
+
+ /*
+ * XXX: Lane A uses pins SD1_RX3_P/N! That is, the lane
+ * numbers and pin numbers are _reversed_. In addition,
+ * the PCCR documentation is _inconsistent_ in its
+ * usage of these terms!
+ *
+ * PCCR "Lane 0" refers to...
+ * ==== =====================
+ * 0 Lane A
+ * 2 Lane A
+ * 8 Lane A
+ * 9 Lane A
+ * B Lane D!
+ */
+ serdes1_A: phy@0 {
+ #phy-cells = <0>;
+ reg = <0>;
+
+ /* SGMII.6 */
+ sgmii-0 {
+ fsl,pccr = <0x8>;
+ fsl,index = <0>;
+ fsl,cfg = <0x1>;
+ fsl,type = <PHY_TYPE_SGMII>;
+ };
+ };
+
+ serdes1_B: phy@1 {
+ #phy-cells = <0>;
+ reg = <1>;
+
+ /* SGMII.5 */
+ sgmii-1 {
+ fsl,pccr = <0x8>;
+ fsl,index = <1>;
+ fsl,cfg = <0x1>;
+ fsl,type = <PHY_TYPE_2500BASEX>;
+ };
+
+ /* QSGMII.6,5,10,1 */
+ qsgmii-1 {
+ fsl,pccr = <0x9>;
+ fsl,index = <1>;
+ fsl,cfg = <0x1>;
+ fsl,type = <PHY_TYPE_QSGMII>;
+ };
+
+ /* TODO: PCIe.1 */
+ };
+
+ serdes1_C: phy@2 {
+ #phy-cells = <0>;
+ reg = <2>;
+
+ /* SGMII.10 */
+ sgmii-2 {
+ fsl,pccr = <0x8>;
+ fsl,index = <2>;
+ fsl,cfg = <0x1>;
+ fsl,type = <PHY_TYPE_2500BASEX>;
+ };
+
+ /* XFI.10 */
+ xfi-0 {
+ fsl,pccr = <0xb>;
+ fsl,index = <0>;
+ fsl,cfg = <0x2>;
+ fsl,type = <PHY_TYPE_10GBASER>;
+ };
+ };
+
+ serdes1_D: phy@3 {
+ #phy-cells = <0>;
+ reg = <3>;
+
+ /* SGMII.9 */
+ sgmii-3 {
+ fsl,pccr = <0x8>;
+ fsl,index = <3>;
+ fsl,cfg = <0x1>;
+ fsl,type = <PHY_TYPE_2500BASEX>;
+ };
+
+ /* XFI.9 */
+ xfi-1 {
+ fsl,pccr = <0xb>;
+ fsl,index = <1>;
+ fsl,cfg = <0x1>;
+ fsl,type = <PHY_TYPE_10GBASER>;
+ };
+ };
+ };
+
+ serdes2: serdes@1eb0000 {
+ compatible = "fsl,ls1046a-serdes", "fsl,lynx-10g";
+ reg = <0x0 0x1eb0000 0x0 0x2000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #clock-cells = <1>;
+ status = "disabled";
+ };
+
dcfg: dcfg@1ee0000 {
compatible = "fsl,ls1046a-dcfg", "syscon";
reg = <0x0 0x1ee0000 0x0 0x1000>;
This adds nodes for the SerDes devices. They are disabled by default to prevent any breakage on existing boards. Signed-off-by: Sean Anderson <sean.anderson@seco.com> --- (no changes since v10) Changes in v10: - Move serdes bindings to SoC dtsi - Add support for all (ethernet) serdes modes - Refer to "nodes" instead of "bindings" - Move compatible/reg first Changes in v4: - Convert to new bindings Changes in v3: - Describe modes in device tree Changes in v2: - Use one phy cell for SerDes1, since no lanes can be grouped - Disable SerDes by default to prevent breaking boards inadvertently. .../arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 111 ++++++++++++++++++ 1 file changed, 111 insertions(+)