@@ -42,6 +42,20 @@ config PHY_QCOM_IPQ806X_SATA
depends on OF
select GENERIC_PHY
+config PHY_QCOM_HDMI
+ tristate "Qualcomm MSM8x60/MSM8960/MSM8974 HDMI PHY driver"
+ depends on ARCH_QCOM || COMPILE_TEST
+ depends on OF
+ depends on COMMON_CLK
+ default DRM_MSM_HDMI && ARCH_QCOM && ARM
+ select GENERIC_PHY
+ help
+ Enable this to support the Qualcomm HDMI PHY presend on 32-bit platforms:
+ MSM8260, MSM8660, MSM8960, APQ8060 and APQ8064.
+
+ Note, this driver is not used on MSM899x platforms, which use
+ PHY_QCOM_QMP_HDMI instead.
+
config PHY_QCOM_PCIE2
tristate "Qualcomm PCIe Gen2 PHY Driver"
depends on OF && COMMON_CLK && (ARCH_QCOM || COMPILE_TEST)
@@ -4,6 +4,12 @@ obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
obj-$(CONFIG_PHY_QCOM_EDP) += phy-qcom-edp.o
obj-$(CONFIG_PHY_QCOM_IPQ4019_USB) += phy-qcom-ipq4019-usb.o
obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
+obj-$(CONFIG_PHY_QCOM_HDMI) += phy-qcom-hdmi.o
+
+phy-qcom-hdmi-y := \
+ phy-qcom-hdmi-preqmp.o \
+ phy-qcom-hdmi-28lpm.o \
+
obj-$(CONFIG_PHY_QCOM_PCIE2) += phy-qcom-pcie2.o
obj-$(CONFIG_PHY_QCOM_QMP_COMBO) += phy-qcom-qmp-combo.o
new file mode 100644
@@ -0,0 +1,439 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2013 Red Hat
+ * Author: Rob Clark <robdclark@gmail.com>
+ * Copyright (c) 2023, Linaro Ltd.
+ */
+
+#include <linux/delay.h>
+#include <linux/iopoll.h>
+
+#include "phy-qcom-hdmi-preqmp.h"
+
+#define REG_HDMI_8960_PHY_REG0 0x00000000
+
+#define REG_HDMI_8960_PHY_REG1 0x00000004
+
+#define REG_HDMI_8960_PHY_REG2 0x00000008
+
+#define REG_HDMI_8960_PHY_REG3 0x0000000c
+
+#define REG_HDMI_8960_PHY_REG4 0x00000010
+
+#define REG_HDMI_8960_PHY_REG5 0x00000014
+
+#define REG_HDMI_8960_PHY_REG6 0x00000018
+
+#define REG_HDMI_8960_PHY_REG7 0x0000001c
+
+#define REG_HDMI_8960_PHY_REG8 0x00000020
+
+#define REG_HDMI_8960_PHY_REG9 0x00000024
+
+#define REG_HDMI_8960_PHY_REG10 0x00000028
+
+#define REG_HDMI_8960_PHY_REG11 0x0000002c
+
+#define REG_HDMI_8960_PHY_REG12 0x00000030
+#define HDMI_8960_PHY_REG12_SW_RESET 0x00000020
+#define HDMI_8960_PHY_REG12_PWRDN_B 0x00000080
+
+#define REG_HDMI_8960_PHY_REG_BIST_CFG 0x00000034
+
+#define REG_HDMI_8960_PHY_DEBUG_BUS_SEL 0x00000038
+
+#define REG_HDMI_8960_PHY_REG_MISC0 0x0000003c
+
+#define REG_HDMI_8960_PHY_REG13 0x00000040
+
+#define REG_HDMI_8960_PHY_REG14 0x00000044
+
+#define REG_HDMI_8960_PHY_REG15 0x00000048
+
+#define REG_HDMI_8960_PHY_PLL_REFCLK_CFG 0x00000000
+
+#define REG_HDMI_8960_PHY_PLL_CHRG_PUMP_CFG 0x00000004
+
+#define REG_HDMI_8960_PHY_PLL_LOOP_FLT_CFG0 0x00000008
+
+#define REG_HDMI_8960_PHY_PLL_LOOP_FLT_CFG1 0x0000000c
+
+#define REG_HDMI_8960_PHY_PLL_IDAC_ADJ_CFG 0x00000010
+
+#define REG_HDMI_8960_PHY_PLL_I_VI_KVCO_CFG 0x00000014
+
+#define REG_HDMI_8960_PHY_PLL_PWRDN_B 0x00000018
+#define HDMI_8960_PHY_PLL_PWRDN_B_PD_PLL 0x00000002
+#define HDMI_8960_PHY_PLL_PWRDN_B_PLL_PWRDN_B 0x00000008
+
+#define REG_HDMI_8960_PHY_PLL_SDM_CFG0 0x0000001c
+
+#define REG_HDMI_8960_PHY_PLL_SDM_CFG1 0x00000020
+
+#define REG_HDMI_8960_PHY_PLL_SDM_CFG2 0x00000024
+
+#define REG_HDMI_8960_PHY_PLL_SDM_CFG3 0x00000028
+
+#define REG_HDMI_8960_PHY_PLL_SDM_CFG4 0x0000002c
+
+#define REG_HDMI_8960_PHY_PLL_SSC_CFG0 0x00000030
+
+#define REG_HDMI_8960_PHY_PLL_SSC_CFG1 0x00000034
+
+#define REG_HDMI_8960_PHY_PLL_SSC_CFG2 0x00000038
+
+#define REG_HDMI_8960_PHY_PLL_SSC_CFG3 0x0000003c
+
+#define REG_HDMI_8960_PHY_PLL_LOCKDET_CFG0 0x00000040
+
+#define REG_HDMI_8960_PHY_PLL_LOCKDET_CFG1 0x00000044
+
+#define REG_HDMI_8960_PHY_PLL_LOCKDET_CFG2 0x00000048
+
+#define REG_HDMI_8960_PHY_PLL_VCOCAL_CFG0 0x0000004c
+
+#define REG_HDMI_8960_PHY_PLL_VCOCAL_CFG1 0x00000050
+
+#define REG_HDMI_8960_PHY_PLL_VCOCAL_CFG2 0x00000054
+
+#define REG_HDMI_8960_PHY_PLL_VCOCAL_CFG3 0x00000058
+
+#define REG_HDMI_8960_PHY_PLL_VCOCAL_CFG4 0x0000005c
+
+#define REG_HDMI_8960_PHY_PLL_VCOCAL_CFG5 0x00000060
+
+#define REG_HDMI_8960_PHY_PLL_VCOCAL_CFG6 0x00000064
+
+#define REG_HDMI_8960_PHY_PLL_VCOCAL_CFG7 0x00000068
+
+#define REG_HDMI_8960_PHY_PLL_DEBUG_SEL 0x0000006c
+
+#define REG_HDMI_8960_PHY_PLL_MISC0 0x00000070
+
+#define REG_HDMI_8960_PHY_PLL_MISC1 0x00000074
+
+#define REG_HDMI_8960_PHY_PLL_MISC2 0x00000078
+
+#define REG_HDMI_8960_PHY_PLL_MISC3 0x0000007c
+
+#define REG_HDMI_8960_PHY_PLL_MISC4 0x00000080
+
+#define REG_HDMI_8960_PHY_PLL_MISC5 0x00000084
+
+#define REG_HDMI_8960_PHY_PLL_MISC6 0x00000088
+
+#define REG_HDMI_8960_PHY_PLL_DEBUG_BUS0 0x0000008c
+
+#define REG_HDMI_8960_PHY_PLL_DEBUG_BUS1 0x00000090
+
+#define REG_HDMI_8960_PHY_PLL_DEBUG_BUS2 0x00000094
+
+#define REG_HDMI_8960_PHY_PLL_STATUS0 0x00000098
+#define HDMI_8960_PHY_PLL_STATUS0_PLL_LOCK 0x00000001
+
+#define REG_HDMI_8960_PHY_PLL_STATUS1 0x0000009c
+
+#define HDMI_8974_VCO_MAX_FREQ 1125000000UL
+#define HDMI_8974_VCO_MIN_FREQ 540000000UL
+
+#define HDMI_8974_COMMON_DIV 5
+
+static unsigned long qcom_28lpm_recalc(struct qcom_hdmi_preqmp_phy *hdmi_phy, unsigned long parent_rate)
+{
+ unsigned long rate;
+ u32 refclk_cfg;
+ u32 dc_offset;
+ u64 fraq_n;
+ u32 val;
+
+ refclk_cfg = hdmi_pll_read(hdmi_phy, REG_HDMI_8960_PHY_PLL_REFCLK_CFG);
+ if (refclk_cfg & BIT(1))
+ parent_rate /= 2;
+ if (refclk_cfg & BIT(3))
+ parent_rate *= 2;
+
+ val = hdmi_pll_read(hdmi_phy, REG_HDMI_8960_PHY_PLL_SDM_CFG0);
+ if (val & 0x40) {
+ dc_offset = val & 0x3f;
+ fraq_n = 0;
+ } else {
+ dc_offset = hdmi_pll_read(hdmi_phy, REG_HDMI_8960_PHY_PLL_SDM_CFG1) & 0x3f;
+ fraq_n = hdmi_pll_read(hdmi_phy, REG_HDMI_8960_PHY_PLL_SDM_CFG2) |
+ (hdmi_pll_read(hdmi_phy, REG_HDMI_8960_PHY_PLL_SDM_CFG3) << 8);
+ }
+
+ rate = (dc_offset + 1) * parent_rate;
+ rate += mult_frac(fraq_n, parent_rate, 0x10000);
+
+ return rate;
+}
+
+static int qcom_28lpm_set_rate(struct qcom_hdmi_preqmp_phy *hdmi_phy, unsigned long parent_rate,
+ unsigned long vco_freq, u32 div_idx)
+{
+ unsigned int pixclk = hdmi_phy->hdmi_opts.pixel_clk_rate;
+ unsigned int int_ref_freq;
+ unsigned int div;
+ unsigned int dc_offset;
+ unsigned int sdm_freq_seed;
+ unsigned int val;
+ bool sdm_mode = false;
+ u32 refclk_cfg;
+ u32 lf_cfg0;
+ u32 lf_cfg1;
+
+ dev_dbg(hdmi_phy->dev, "rate=%u, div = %d, vco = %lu", pixclk, div, vco_freq);
+
+ if (vco_freq % (parent_rate / 2) == 0) {
+ refclk_cfg = 0x2;
+ int_ref_freq = parent_rate / 2;
+ } else {
+ refclk_cfg = 0x8;
+ int_ref_freq = parent_rate * 2;
+ sdm_mode = true;
+ }
+
+ dc_offset = vco_freq / int_ref_freq - 1;
+ sdm_freq_seed = vco_freq - (dc_offset + 1) * int_ref_freq;
+ sdm_freq_seed = mult_frac(sdm_freq_seed, 0x10000, int_ref_freq);
+
+ val = (div_idx << 4) | refclk_cfg;
+ hdmi_pll_write(hdmi_phy, REG_HDMI_8960_PHY_PLL_REFCLK_CFG, val);
+
+ lf_cfg0 = dc_offset >= 30 ? 0 : (dc_offset >= 16 ? 0x10 : 0x20);
+ lf_cfg0 += sdm_mode ? 0 : 1;
+
+ /* XXX: 0xc3 instead of 0x33 for qcs404 */
+ lf_cfg1 = dc_offset >= 30 ? 0x33 : (dc_offset >= 16 ? 0xbb : 0xf9);
+
+ hdmi_pll_write(hdmi_phy, REG_HDMI_8960_PHY_PLL_LOOP_FLT_CFG0, lf_cfg0);
+ hdmi_pll_write(hdmi_phy, REG_HDMI_8960_PHY_PLL_LOOP_FLT_CFG1, lf_cfg1);
+
+ hdmi_pll_write(hdmi_phy, REG_HDMI_8960_PHY_PLL_SDM_CFG0,
+ (sdm_mode ? 0 : 0x40) | dc_offset);
+ hdmi_pll_write(hdmi_phy, REG_HDMI_8960_PHY_PLL_SDM_CFG1,
+ 0x40 | dc_offset);
+
+ hdmi_pll_write(hdmi_phy, REG_HDMI_8960_PHY_PLL_SDM_CFG2,
+ sdm_freq_seed & 0xff);
+
+ hdmi_pll_write(hdmi_phy, REG_HDMI_8960_PHY_PLL_SDM_CFG3,
+ (sdm_freq_seed >> 8) & 0xff);
+
+ hdmi_pll_write(hdmi_phy, REG_HDMI_8960_PHY_PLL_SDM_CFG4,
+ sdm_freq_seed >> 16);
+
+ vco_freq /= 1000;
+ hdmi_pll_write(hdmi_phy, REG_HDMI_8960_PHY_PLL_VCOCAL_CFG0, vco_freq & 0xff);
+ hdmi_pll_write(hdmi_phy, REG_HDMI_8960_PHY_PLL_VCOCAL_CFG1, vco_freq >> 8);
+
+ hdmi_pll_write(hdmi_phy, REG_HDMI_8960_PHY_PLL_VCOCAL_CFG2, 0x3b);
+
+ return 0;
+}
+
+static const unsigned int qcom_hdmi_8974_divs[] = {1, 2, 4, 6};
+
+static unsigned long qcom_hdmi_8960_pll_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct qcom_hdmi_preqmp_phy *hdmi_phy = hw_clk_to_phy(hw);
+ u32 div_idx = hdmi_pll_read(hdmi_phy, REG_HDMI_8960_PHY_PLL_REFCLK_CFG);
+ unsigned long rate = qcom_28lpm_recalc(hdmi_phy, parent_rate);
+
+ return rate / HDMI_8974_COMMON_DIV / qcom_hdmi_8974_divs[div_idx >> 4];
+}
+
+static long qcom_hdmi_8960_pll_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *parent_rate)
+{
+ return clamp(rate,
+ HDMI_8974_VCO_MIN_FREQ / HDMI_8974_COMMON_DIV / 6,
+ HDMI_8974_VCO_MAX_FREQ / HDMI_8974_COMMON_DIV / 1);
+}
+
+static const struct clk_ops qcom_hdmi_8960_pll_ops = {
+ .recalc_rate = qcom_hdmi_8960_pll_recalc_rate,
+ .round_rate = qcom_hdmi_8960_pll_round_rate,
+};
+
+static int qcom_hdmi_msm8960_phy_pll_enable(struct qcom_hdmi_preqmp_phy *phy)
+{
+ int pll_lock_retry = 10;
+ unsigned int val;
+ int ret;
+
+ /* Assert PLL S/W reset */
+ hdmi_pll_write(phy, REG_HDMI_8960_PHY_PLL_LOCKDET_CFG2, 0x8d);
+ hdmi_pll_write(phy, REG_HDMI_8960_PHY_PLL_LOCKDET_CFG0, 0x10);
+ hdmi_pll_write(phy, REG_HDMI_8960_PHY_PLL_LOCKDET_CFG1, 0x1a);
+
+ /* Wait for a short time before de-asserting
+ * to allow the hardware to complete its job.
+ * This much of delay should be fine for hardware
+ * to assert and de-assert.
+ */
+ udelay(10);
+
+ /* De-assert PLL S/W reset */
+ hdmi_pll_write(phy, REG_HDMI_8960_PHY_PLL_LOCKDET_CFG2, 0x0d);
+
+ val = hdmi_phy_read(phy, REG_HDMI_8960_PHY_REG12);
+ val |= HDMI_8960_PHY_REG12_SW_RESET;
+ /* Assert PHY S/W reset */
+ hdmi_phy_write(phy, REG_HDMI_8960_PHY_REG12, val);
+ val &= ~HDMI_8960_PHY_REG12_SW_RESET;
+ /*
+ * Wait for a short time before de-asserting to allow the hardware to
+ * complete its job. This much of delay should be fine for hardware to
+ * assert and de-assert.
+ */
+ udelay(10);
+ /* De-assert PHY S/W reset */
+ hdmi_phy_write(phy, REG_HDMI_8960_PHY_REG12, val);
+ hdmi_phy_write(phy, REG_HDMI_8960_PHY_REG2, 0x3f);
+
+ val = hdmi_phy_read(phy, REG_HDMI_8960_PHY_REG12);
+ val |= HDMI_8960_PHY_REG12_PWRDN_B;
+ hdmi_phy_write(phy, REG_HDMI_8960_PHY_REG12, val);
+ /* Wait 10 us for enabling global power for PHY */
+ mb();
+ udelay(10);
+
+ val = hdmi_pll_read(phy, REG_HDMI_8960_PHY_PLL_PWRDN_B);
+ val |= HDMI_8960_PHY_PLL_PWRDN_B_PLL_PWRDN_B;
+ val &= ~HDMI_8960_PHY_PLL_PWRDN_B_PD_PLL;
+ hdmi_pll_write(phy, REG_HDMI_8960_PHY_PLL_PWRDN_B, val);
+ hdmi_phy_write(phy, REG_HDMI_8960_PHY_REG2, 0x80);
+
+ while (--pll_lock_retry > 0) {
+ ret = readl_poll_timeout(phy->pll_reg + REG_HDMI_8960_PHY_PLL_STATUS0,
+ val, val & HDMI_8960_PHY_PLL_STATUS0_PLL_LOCK,
+ 1, 1000);
+ if (!ret)
+ break;
+
+ /*
+ * PLL has still not locked.
+ * Do a software reset and try again
+ * Assert PLL S/W reset first
+ */
+ hdmi_pll_write(phy, REG_HDMI_8960_PHY_PLL_LOCKDET_CFG2, 0x8d);
+ udelay(10);
+ hdmi_pll_write(phy, REG_HDMI_8960_PHY_PLL_LOCKDET_CFG2, 0x0d);
+
+ /*
+ * Wait for a short duration for the PLL calibration
+ * before checking if the PLL gets locked
+ */
+ udelay(350);
+ }
+
+ return ret;
+}
+
+static int qcom_hdmi_msm8974_phy_find_div(unsigned int pixclk)
+{
+ int i;
+ unsigned int min_freq = HDMI_8974_VCO_MIN_FREQ / HDMI_8974_COMMON_DIV / 1000;
+
+ if (pixclk > HDMI_8974_VCO_MAX_FREQ / HDMI_8974_COMMON_DIV / 1000)
+ return -E2BIG;
+
+ for (i = 0; i < ARRAY_SIZE(qcom_hdmi_8974_divs); i++) {
+ if (pixclk >= min_freq / qcom_hdmi_8974_divs[i])
+ return i;
+ }
+
+ return -EINVAL;
+}
+
+static int qcom_hdmi_msm8960_phy_set_rate(struct qcom_hdmi_preqmp_phy *hdmi_phy)
+{
+ unsigned int pixclk = hdmi_phy->hdmi_opts.pixel_clk_rate;
+ /* XXX: 19.2 for qcs404 */
+ unsigned long parent_rate = 27000;
+ unsigned long vco_freq;
+ int div_idx;
+ u32 div;
+
+ div_idx = qcom_hdmi_msm8974_phy_find_div(pixclk);
+ if (WARN_ON(div_idx < 0))
+ return div_idx;
+
+ div = qcom_hdmi_8974_divs[div_idx];
+ vco_freq = pixclk * HDMI_8974_COMMON_DIV * div;
+
+ return qcom_28lpm_set_rate(hdmi_phy, parent_rate, vco_freq, div_idx);
+}
+
+static void qcom_hdmi_msm8960_phy_pll_disable(struct qcom_hdmi_preqmp_phy *phy)
+{
+ unsigned int val;
+
+ val = hdmi_phy_read(phy, REG_HDMI_8960_PHY_REG12);
+ val &= ~HDMI_8960_PHY_REG12_PWRDN_B;
+ hdmi_phy_write(phy, REG_HDMI_8960_PHY_REG12, val);
+
+ val = hdmi_pll_read(phy, REG_HDMI_8960_PHY_PLL_PWRDN_B);
+ val |= HDMI_8960_PHY_REG12_SW_RESET;
+ val &= ~HDMI_8960_PHY_REG12_PWRDN_B;
+ hdmi_pll_write(phy, REG_HDMI_8960_PHY_PLL_PWRDN_B, val);
+ /* Make sure HDMI PHY/PLL are powered down */
+ mb();
+}
+
+static int qcom_hdmi_msm8960_phy_power_on(struct qcom_hdmi_preqmp_phy *hdmi_phy)
+{
+ int ret;
+
+ ret = qcom_hdmi_msm8960_phy_set_rate(hdmi_phy);
+ if (ret)
+ return ret;
+
+ ret = qcom_hdmi_msm8960_phy_pll_enable(hdmi_phy);
+ if (ret)
+ return ret;
+
+ hdmi_phy_write(hdmi_phy, REG_HDMI_8960_PHY_REG2, 0x00);
+ hdmi_phy_write(hdmi_phy, REG_HDMI_8960_PHY_REG0, 0x1b);
+ hdmi_phy_write(hdmi_phy, REG_HDMI_8960_PHY_REG1, 0xf2);
+ hdmi_phy_write(hdmi_phy, REG_HDMI_8960_PHY_REG4, 0x00);
+ hdmi_phy_write(hdmi_phy, REG_HDMI_8960_PHY_REG5, 0x00);
+ hdmi_phy_write(hdmi_phy, REG_HDMI_8960_PHY_REG6, 0x00);
+ hdmi_phy_write(hdmi_phy, REG_HDMI_8960_PHY_REG7, 0x00);
+ hdmi_phy_write(hdmi_phy, REG_HDMI_8960_PHY_REG8, 0x00);
+ hdmi_phy_write(hdmi_phy, REG_HDMI_8960_PHY_REG9, 0x00);
+ hdmi_phy_write(hdmi_phy, REG_HDMI_8960_PHY_REG10, 0x00);
+ hdmi_phy_write(hdmi_phy, REG_HDMI_8960_PHY_REG11, 0x00);
+ hdmi_phy_write(hdmi_phy, REG_HDMI_8960_PHY_REG3, 0x20);
+
+ return 0;
+}
+
+static int qcom_hdmi_msm8960_phy_power_off(struct qcom_hdmi_preqmp_phy *hdmi_phy)
+{
+ hdmi_phy_write(hdmi_phy, REG_HDMI_8960_PHY_REG2, 0x7f);
+
+ qcom_hdmi_msm8960_phy_pll_disable(hdmi_phy);
+
+ return 0;
+}
+
+const struct clk_parent_data msm8960_hdmi_pll_parent = {
+ .fw_name = "pxo", .name = "pxo_board",
+};
+
+const struct qcom_hdmi_preqmp_cfg msm8960_hdmi_phy_cfg = {
+ .clk_names = { "slave_iface" },
+ .num_clks = 1,
+
+ .reg_names = { "core-vdda" },
+ .num_regs = 1,
+
+ .power_on = qcom_hdmi_msm8960_phy_power_on,
+ .power_off = qcom_hdmi_msm8960_phy_power_off,
+
+ .pll_ops = &qcom_hdmi_8960_pll_ops,
+ .pll_parent = &msm8960_hdmi_pll_parent,
+};
new file mode 100644
@@ -0,0 +1,206 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2013 Red Hat
+ * Author: Rob Clark <robdclark@gmail.com>
+ * Copyright (c) 2023, Linaro Ltd.
+ */
+
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+
+#include "phy-qcom-hdmi-preqmp.h"
+
+static int qcom_hdmi_preqmp_phy_init(struct phy *phy)
+{
+ struct qcom_hdmi_preqmp_phy *hdmi_phy = phy_get_drvdata(phy);
+
+ return pm_runtime_resume_and_get(hdmi_phy->dev);
+}
+
+static int qcom_hdmi_preqmp_phy_exit(struct phy *phy)
+{
+ struct qcom_hdmi_preqmp_phy *hdmi_phy = phy_get_drvdata(phy);
+
+ pm_runtime_put_noidle(hdmi_phy->dev);
+
+ return 0;
+}
+
+static int qcom_hdmi_preqmp_phy_power_on(struct phy *phy)
+{
+ struct qcom_hdmi_preqmp_phy *hdmi_phy = phy_get_drvdata(phy);
+
+ return hdmi_phy->power_on(hdmi_phy);
+};
+
+static int qcom_hdmi_preqmp_phy_power_off(struct phy *phy)
+{
+ struct qcom_hdmi_preqmp_phy *hdmi_phy = phy_get_drvdata(phy);
+
+ return hdmi_phy->power_off(hdmi_phy);
+};
+
+static int qcom_hdmi_preqmp_phy_configure(struct phy *phy, union phy_configure_opts *opts)
+{
+ const struct phy_configure_opts_hdmi *hdmi_opts = &opts->hdmi;
+ struct qcom_hdmi_preqmp_phy *hdmi_phy = phy_get_drvdata(phy);
+ int ret = 0;
+
+ memcpy(&hdmi_phy->hdmi_opts, hdmi_opts, sizeof(*hdmi_opts));
+
+ return ret;
+}
+
+static int __maybe_unused qcom_hdmi_preqmp_runtime_resume(struct device *dev)
+{
+ struct qcom_hdmi_preqmp_phy *hdmi_phy = dev_get_drvdata(dev);
+ int ret;
+
+ ret = regulator_bulk_enable(hdmi_phy->num_regs, hdmi_phy->regs);
+ if (ret)
+ return ret;
+
+ ret = clk_bulk_prepare_enable(hdmi_phy->num_clks, hdmi_phy->clks);
+ if (ret)
+ goto out_disable_supplies;
+
+ return 0;
+
+out_disable_supplies:
+ regulator_bulk_disable(hdmi_phy->num_regs, hdmi_phy->regs);
+
+ return ret;
+}
+
+static int __maybe_unused qcom_hdmi_preqmp_runtime_suspend(struct device *dev)
+{
+ struct qcom_hdmi_preqmp_phy *hdmi_phy = dev_get_drvdata(dev);
+
+ clk_bulk_disable_unprepare(hdmi_phy->num_clks, hdmi_phy->clks);
+ regulator_bulk_disable(hdmi_phy->num_regs, hdmi_phy->regs);
+
+ return 0;
+}
+
+static const struct phy_ops qcom_hdmi_preqmp_phy_ops = {
+ .init = qcom_hdmi_preqmp_phy_init,
+ .configure = qcom_hdmi_preqmp_phy_configure,
+ .power_on = qcom_hdmi_preqmp_phy_power_on,
+ .power_off = qcom_hdmi_preqmp_phy_power_off,
+ .exit = qcom_hdmi_preqmp_phy_exit,
+ .owner = THIS_MODULE,
+};
+
+static int qcom_hdmi_preqmp_probe(struct platform_device *pdev)
+{
+ struct clk_init_data init;
+ struct phy_provider *phy_provider;
+ struct device *dev = &pdev->dev;
+ struct qcom_hdmi_preqmp_phy *hdmi_phy;
+ const struct qcom_hdmi_preqmp_cfg *cfg;
+ int i, ret;
+
+ cfg = of_device_get_match_data(dev);
+ if (!cfg)
+ return -EINVAL;
+
+ hdmi_phy = devm_kzalloc(dev, sizeof(*hdmi_phy), GFP_KERNEL);
+ if (!hdmi_phy)
+ return -ENOMEM;
+
+ hdmi_phy->dev = dev;
+
+ hdmi_phy->phy_reg = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(hdmi_phy->phy_reg))
+ return PTR_ERR(hdmi_phy->phy_reg);
+
+ hdmi_phy->pll_reg = devm_platform_ioremap_resource(pdev, 1);
+ if (IS_ERR(hdmi_phy->pll_reg))
+ return PTR_ERR(hdmi_phy->pll_reg);
+
+ hdmi_phy->num_clks = cfg->num_clks;
+ for (i = 0; i < cfg->num_clks; i++)
+ hdmi_phy->clks[i].id = cfg->clk_names[i];
+ ret = devm_clk_bulk_get(dev, hdmi_phy->num_clks, hdmi_phy->clks);
+ if (ret)
+ return ret;
+
+ hdmi_phy->num_regs = cfg->num_regs;
+ for (i = 0; i < cfg->num_regs; i++) {
+ hdmi_phy->regs[i].supply = cfg->reg_names[i];
+ hdmi_phy->regs[i].init_load_uA = cfg->reg_init_load[i];
+ }
+ ret = devm_regulator_bulk_get(dev, hdmi_phy->num_regs, hdmi_phy->regs);
+ if (ret)
+ return ret;
+
+ hdmi_phy->power_on = cfg->power_on;
+ hdmi_phy->power_off = cfg->power_off;
+
+ platform_set_drvdata(pdev, hdmi_phy);
+
+ ret = devm_pm_runtime_enable(&pdev->dev);
+ if (ret)
+ return ret;
+
+ ret = pm_runtime_resume_and_get(&pdev->dev);
+ if (ret)
+ return ret;
+
+ init.name = "hdmipll";
+ init.ops = cfg->pll_ops;
+ init.flags = CLK_GET_RATE_NOCACHE;
+ init.parent_data = cfg->pll_parent;
+ init.num_parents = 1;
+
+ hdmi_phy->pll_hw.init = &init;
+ ret = devm_clk_hw_register(hdmi_phy->dev, &hdmi_phy->pll_hw);
+ if (ret)
+ goto err;
+
+ ret = devm_of_clk_add_hw_provider(hdmi_phy->dev, of_clk_hw_simple_get, &hdmi_phy->pll_hw);
+ if (ret)
+ goto err;
+
+ hdmi_phy->phy = devm_phy_create(dev, pdev->dev.of_node, &qcom_hdmi_preqmp_phy_ops);
+ if (IS_ERR(hdmi_phy->phy)) {
+ ret = PTR_ERR(hdmi_phy->phy);
+ goto err;
+ }
+
+ phy_set_drvdata(hdmi_phy->phy, hdmi_phy);
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ pm_runtime_put_noidle(&pdev->dev);
+ return PTR_ERR_OR_ZERO(phy_provider);
+
+err:
+ pm_runtime_put_noidle(&pdev->dev);
+ return ret;
+}
+
+static const struct of_device_id qcom_hdmi_preqmp_of_match_table[] = {
+ { .compatible = "qcom,hdmi-phy-8960", .data = &msm8960_hdmi_phy_cfg, },
+ { },
+};
+MODULE_DEVICE_TABLE(of, qcom_hdmi_preqmp_of_match_table);
+
+DEFINE_RUNTIME_DEV_PM_OPS(qcom_hdmi_preqmp_pm_ops,
+ qcom_hdmi_preqmp_runtime_suspend,
+ qcom_hdmi_preqmp_runtime_resume,
+ NULL);
+
+static struct platform_driver qcom_hdmi_preqmp_driver = {
+ .probe = qcom_hdmi_preqmp_probe,
+ .driver = {
+ .name = "qcom-preqmp-hdmi-phy",
+ .of_match_table = qcom_hdmi_preqmp_of_match_table,
+ .pm = &qcom_hdmi_preqmp_pm_ops,
+ },
+};
+
+module_platform_driver(qcom_hdmi_preqmp_driver);
+
+MODULE_AUTHOR("Dmitry Baryshkov <dmitry.baryshkov@linaro.org>");
+MODULE_DESCRIPTION("Qualcomm MSMpreqmp HDMI PHY driver");
+MODULE_LICENSE("GPL");
new file mode 100644
@@ -0,0 +1,79 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2013 Red Hat
+ * Author: Rob Clark <robdclark@gmail.com>
+ * Copyright (c) 2023, Linaro Ltd.
+ */
+
+#ifndef PHY_QCOM_HDMI_PREQMP_H
+#define PHY_QCOM_HDMI_PREQMP_H
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/phy/phy-hdmi.h>
+#include <linux/regulator/consumer.h>
+
+#define MAX_CLKS 2
+#define MAX_SUPPLIES 2
+
+struct qcom_hdmi_preqmp_phy {
+ struct device *dev;
+ struct phy *phy;
+ void __iomem *pll_reg;
+ void __iomem *phy_reg;
+
+ struct phy_configure_opts_hdmi hdmi_opts;
+
+ struct clk_hw pll_hw;
+ struct clk_bulk_data clks[MAX_CLKS];
+ int num_clks;
+
+ struct regulator_bulk_data regs[MAX_SUPPLIES];
+ int num_regs;
+
+ int (*power_on)(struct qcom_hdmi_preqmp_phy *phy);
+ int (*power_off)(struct qcom_hdmi_preqmp_phy *phy);
+};
+
+#define hw_clk_to_phy(x) container_of(x, struct qcom_hdmi_preqmp_phy, pll_hw)
+
+struct qcom_hdmi_preqmp_cfg {
+ const char * const clk_names[MAX_CLKS];
+ int num_clks;
+
+ const char * const reg_names[MAX_SUPPLIES];
+ int reg_init_load[MAX_SUPPLIES];
+ int num_regs;
+
+ int (*power_on)(struct qcom_hdmi_preqmp_phy *phy);
+ int (*power_off)(struct qcom_hdmi_preqmp_phy *phy);
+
+ const struct clk_ops *pll_ops;
+ const struct clk_parent_data *pll_parent;
+};
+
+static inline void hdmi_phy_write(struct qcom_hdmi_preqmp_phy *phy, int offset,
+ u32 data)
+{
+ writel(data, phy->phy_reg + offset);
+}
+
+static inline u32 hdmi_phy_read(struct qcom_hdmi_preqmp_phy *phy, int offset)
+{
+ return readl(phy->phy_reg + offset);
+}
+
+static inline void hdmi_pll_write(struct qcom_hdmi_preqmp_phy *phy, int offset,
+ u32 data)
+{
+ writel(data, phy->pll_reg + offset);
+}
+
+static inline u32 hdmi_pll_read(struct qcom_hdmi_preqmp_phy *phy, int offset)
+{
+ return readl(phy->pll_reg + offset);
+}
+
+extern const struct qcom_hdmi_preqmp_cfg msm8960_hdmi_phy_cfg;
+
+#endif
Add the driver for pre-QMP Qualcomm HDMI PHYs. Currently it suppports Qualcomm MSM8960 / APQ8064 platforms, other platforms will come later. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- drivers/phy/qualcomm/Kconfig | 14 + drivers/phy/qualcomm/Makefile | 6 + drivers/phy/qualcomm/phy-qcom-hdmi-28lpm.c | 439 ++++++++++++++++++++ drivers/phy/qualcomm/phy-qcom-hdmi-preqmp.c | 206 +++++++++ drivers/phy/qualcomm/phy-qcom-hdmi-preqmp.h | 79 ++++ 5 files changed, 744 insertions(+) create mode 100644 drivers/phy/qualcomm/phy-qcom-hdmi-28lpm.c create mode 100644 drivers/phy/qualcomm/phy-qcom-hdmi-preqmp.c create mode 100644 drivers/phy/qualcomm/phy-qcom-hdmi-preqmp.h