@@ -33,6 +33,17 @@ config PHY_STIH407_USB
Enable this support to enable the picoPHY device used by USB2
and USB3 controllers on STMicroelectronics STiH407 SoC families.
+config PHY_STM32_COMBOPHY
+ tristate "STMicroelectronics COMBOPHY driver for STM32MP25"
+ depends on ARCH_STM32 || COMPILE_TEST
+ select GENERIC_PHY
+ help
+ Enable this to support the COMBOPHY device used by USB3 or PCIe
+ controllers on STMicroelectronics STM32MP25 SoC.
+ This driver controls the COMBOPHY block to generate the PCIe 100Mhz
+ reference clock from either the external clock generator or HSE
+ internal SoC clock source.
+
config PHY_STM32_USBPHYC
tristate "STMicroelectronics STM32 USB HS PHY Controller driver"
depends on ARCH_STM32 || COMPILE_TEST
@@ -3,4 +3,5 @@ obj-$(CONFIG_PHY_MIPHY28LP) += phy-miphy28lp.o
obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o
obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o
obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o
+obj-$(CONFIG_PHY_STM32_COMBOPHY) += phy-stm32-combophy.o
obj-$(CONFIG_PHY_STM32_USBPHYC) += phy-stm32-usbphyc.o
new file mode 100644
@@ -0,0 +1,607 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * STMicroelectronics COMBOPHY STM32MP25 Controller driver.
+ *
+ * Copyright (C) 2024 STMicroelectronics
+ * Author: Christian Bruel <christian.bruel@foss.st.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <dt-bindings/phy/phy.h>
+
+#define SYSCFG_COMBOPHY_CR1 0x4C00
+#define SYSCFG_COMBOPHY_CR2 0x4C04
+#define SYSCFG_COMBOPHY_CR4 0x4C0C
+#define SYSCFG_COMBOPHY_CR5 0x4C10
+#define SYSCFG_COMBOPHY_SR 0x4C14
+#define SYSCFG_PCIEPRGCR 0x6080
+
+/* SYSCFG PCIEPRGCR */
+#define STM32MP25_PCIEPRGCR_EN BIT(0)
+#define STM32MP25_PCIEPRG_IMPCTRL_OHM GENMASK(3, 1)
+#define STM32MP25_PCIEPRG_IMPCTRL_VSWING GENMASK(5, 4)
+
+/* SYSCFG SYSCFG_COMBOPHY_SR */
+#define STM32MP25_PIPE0_PHYSTATUS BIT(1)
+
+/* SYSCFG CR1 */
+#define SYSCFG_COMBOPHY_CR1_REFUSEPAD BIT(0)
+#define SYSCFG_COMBOPHY_CR1_MPLLMULT GENMASK(7, 1)
+#define SYSCFG_COMBOPHY_CR1_REFCLKSEL GENMASK(16, 8)
+#define SYSCFG_COMBOPHY_CR1_REFCLKDIV2 BIT(17)
+#define SYSCFG_COMBOPHY_CR1_REFSSPEN BIT(18)
+#define SYSCFG_COMBOPHY_CR1_SSCEN BIT(19)
+
+/* SYSCFG CR4 */
+#define SYSCFG_COMBOPHY_CR4_RX0_EQ GENMASK(2, 0)
+
+#define MPLLMULT_19_2 (0x02u << 1)
+#define MPLLMULT_20 (0x7Du << 1)
+#define MPLLMULT_24 (0x68u << 1)
+#define MPLLMULT_25 (0x64u << 1)
+#define MPLLMULT_26 (0x60u << 1)
+#define MPLLMULT_38_4 (0x41u << 1)
+#define MPLLMULT_48 (0x6Cu << 1)
+#define MPLLMULT_50 (0x32u << 1)
+#define MPLLMULT_52 (0x30u << 1)
+#define MPLLMULT_100 (0x19u << 1)
+
+#define REFCLKSEL_0 0
+#define REFCLKSEL_1 (0x108u << 8)
+
+#define REFCLDIV_0 0
+
+/* SYSCFG CR2 */
+#define SYSCFG_COMBOPHY_CR2_MODESEL GENMASK(1, 0)
+#define SYSCFG_COMBOPHY_CR2_ISO_DIS BIT(15)
+
+#define COMBOPHY_MODESEL_PCIE 0
+#define COMBOPHY_MODESEL_USB 3
+
+/* SYSCFG CR5 */
+#define SYSCFG_COMBOPHY_CR5_COMMON_CLOCKS BIT(12)
+
+#define COMBOPHY_SUP_ANA_MPLL_LOOP_CTL 0xC0
+#define COMBOPHY_PROP_CNTRL GENMASK(7, 4)
+
+struct stm32_combophy {
+ struct phy *phy;
+ struct regmap *regmap;
+ struct device *dev;
+ void __iomem *base;
+ struct reset_control *phy_reset;
+ struct clk *phy_clk;
+ struct clk *pad_clk;
+ struct clk *ker_clk;
+ unsigned int type;
+ bool is_init;
+ int irq_wakeup;
+};
+
+struct clk_impedance {
+ u32 microohm;
+ u32 vswing[4];
+};
+
+/*
+ * lookup table to hold the settings needed for a ref clock frequency
+ * impedance, the offset is used to set the IMP_CTL and DE_EMP bit of the
+ * PRG_IMP_CTRL register
+ */
+static const struct clk_impedance imp_lookup[] = {
+ { 6090000, { 442000, 564000, 684000, 802000 } },
+ { 5662000, { 528000, 621000, 712000, 803000 } },
+ { 5292000, { 491000, 596000, 700000, 802000 } },
+ { 4968000, { 558000, 640000, 722000, 803000 } },
+ { 4684000, { 468000, 581000, 692000, 802000 } },
+ { 4429000, { 554000, 613000, 717000, 803000 } },
+ { 4204000, { 511000, 609000, 706000, 802000 } },
+ { 3999000, { 571000, 648000, 726000, 803000 } }
+};
+
+static int stm32_impedance_tune(struct stm32_combophy *combophy)
+{
+ u8 imp_size = ARRAY_SIZE(imp_lookup);
+ u8 vswing_size = ARRAY_SIZE(imp_lookup[0].vswing);
+ u8 imp_of, vswing_of;
+ u32 max_imp = imp_lookup[0].microohm;
+ u32 min_imp = imp_lookup[imp_size - 1].microohm;
+ u32 max_vswing = imp_lookup[imp_size - 1].vswing[vswing_size - 1];
+ u32 min_vswing = imp_lookup[0].vswing[0];
+ u32 val;
+
+ if (!of_property_read_u32(combophy->dev->of_node, "st,output-micro-ohms", &val)) {
+ if (val < min_imp || val > max_imp) {
+ dev_err(combophy->dev, "Invalid value %u for output ohm\n", val);
+ return -EINVAL;
+ }
+
+ for (imp_of = 0 ; imp_of < ARRAY_SIZE(imp_lookup); imp_of++)
+ if (imp_lookup[imp_of].microohm <= val)
+ break;
+
+ dev_dbg(combophy->dev, "Set %u micro-ohms output impedance\n",
+ imp_lookup[imp_of].microohm);
+
+ regmap_update_bits(combophy->regmap, SYSCFG_PCIEPRGCR,
+ STM32MP25_PCIEPRG_IMPCTRL_OHM,
+ FIELD_PREP(STM32MP25_PCIEPRG_IMPCTRL_OHM, imp_of));
+ } else {
+ regmap_read(combophy->regmap, SYSCFG_PCIEPRGCR, &val);
+ imp_of = FIELD_GET(STM32MP25_PCIEPRG_IMPCTRL_OHM, val);
+ }
+
+ if (!of_property_read_u32(combophy->dev->of_node, "st,output-vswing-microvolt", &val)) {
+ if (val < min_vswing || val > max_vswing) {
+ dev_err(combophy->dev, "Invalid value %u for output vswing\n", val);
+ return -EINVAL;
+ }
+
+ for (vswing_of = 0 ; vswing_of < ARRAY_SIZE(imp_lookup[imp_of].vswing); vswing_of++)
+ if (imp_lookup[imp_of].vswing[vswing_of] >= val)
+ break;
+
+ dev_dbg(combophy->dev, "Set %u microvolt swing\n",
+ imp_lookup[imp_of].vswing[vswing_of]);
+
+ regmap_update_bits(combophy->regmap, SYSCFG_PCIEPRGCR,
+ STM32MP25_PCIEPRG_IMPCTRL_VSWING,
+ FIELD_PREP(STM32MP25_PCIEPRG_IMPCTRL_VSWING, vswing_of));
+ }
+
+ return 0;
+}
+
+static int stm32_combophy_pll_init(struct stm32_combophy *combophy)
+{
+ int ret;
+ u32 refclksel, pllmult, propcntrl, val;
+ u32 clk_rate;
+
+ if (combophy->pad_clk)
+ clk_rate = clk_get_rate(combophy->pad_clk);
+ else
+ clk_rate = clk_get_rate(combophy->ker_clk);
+
+ reset_control_assert(combophy->phy_reset);
+
+ dev_dbg(combophy->dev, "%s pll init rate %d\n",
+ combophy->pad_clk ? "External" : "Ker", clk_rate);
+
+ /*
+ * vddcombophy is interconnected with vddcore. Isolation bit should be unset
+ * before using the ComboPHY.
+ */
+ regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR2,
+ SYSCFG_COMBOPHY_CR2_ISO_DIS, SYSCFG_COMBOPHY_CR2_ISO_DIS);
+
+ if (combophy->type != PHY_TYPE_PCIE)
+ regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR1,
+ SYSCFG_COMBOPHY_CR1_REFSSPEN, SYSCFG_COMBOPHY_CR1_REFSSPEN);
+
+ if (combophy->type == PHY_TYPE_PCIE && !combophy->pad_clk)
+ regmap_update_bits(combophy->regmap, SYSCFG_PCIEPRGCR,
+ STM32MP25_PCIEPRGCR_EN, STM32MP25_PCIEPRGCR_EN);
+
+ if (of_property_read_bool(combophy->dev->of_node, "st,ssc-on")) {
+ dev_dbg(combophy->dev, "Enabling clock with SSC\n");
+ regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR1,
+ SYSCFG_COMBOPHY_CR1_SSCEN, SYSCFG_COMBOPHY_CR1_SSCEN);
+ }
+
+ if (!of_property_read_u32(combophy->dev->of_node, "st,rx_equalizer", &val)) {
+ dev_dbg(combophy->dev, "Set RX equalizer %u\n", val);
+ if (val > SYSCFG_COMBOPHY_CR4_RX0_EQ) {
+ dev_err(combophy->dev, "Invalid value %u for rx0 equalizer\n", val);
+ return -EINVAL;
+ }
+
+ regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR4,
+ SYSCFG_COMBOPHY_CR4_RX0_EQ, val);
+ }
+
+ if (combophy->type == PHY_TYPE_PCIE) {
+ ret = stm32_impedance_tune(combophy);
+ if (ret) {
+ reset_control_deassert(combophy->phy_reset);
+ goto out;
+ }
+
+ regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR1,
+ SYSCFG_COMBOPHY_CR1_REFUSEPAD,
+ combophy->pad_clk ? SYSCFG_COMBOPHY_CR1_REFUSEPAD : 0);
+ }
+
+ switch (clk_rate) {
+ case 100000000:
+ pllmult = MPLLMULT_100;
+ refclksel = REFCLKSEL_0;
+ propcntrl = 0x8u << 4;
+ break;
+ case 19200000:
+ pllmult = MPLLMULT_19_2;
+ refclksel = REFCLKSEL_1;
+ propcntrl = 0x8u << 4;
+ break;
+ case 25000000:
+ pllmult = MPLLMULT_25;
+ refclksel = REFCLKSEL_0;
+ propcntrl = 0xEu << 4;
+ break;
+ case 24000000:
+ pllmult = MPLLMULT_24;
+ refclksel = REFCLKSEL_1;
+ propcntrl = 0xEu << 4;
+ break;
+ case 20000000:
+ pllmult = MPLLMULT_20;
+ refclksel = REFCLKSEL_0;
+ propcntrl = 0xEu << 4;
+ break;
+ default:
+ dev_err(combophy->dev, "Invalid rate 0x%x\n", clk_rate);
+ reset_control_deassert(combophy->phy_reset);
+ ret = -EINVAL;
+ goto out;
+ };
+
+ regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR1,
+ SYSCFG_COMBOPHY_CR1_REFCLKDIV2, REFCLDIV_0);
+ regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR1,
+ SYSCFG_COMBOPHY_CR1_REFCLKSEL, refclksel);
+ regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR1,
+ SYSCFG_COMBOPHY_CR1_MPLLMULT, pllmult);
+
+ /*
+ * Force elasticity buffer to be tuned for the reference clock as
+ * the separated clock model is not supported
+ */
+ regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR5,
+ SYSCFG_COMBOPHY_CR5_COMMON_CLOCKS, SYSCFG_COMBOPHY_CR5_COMMON_CLOCKS);
+
+ reset_control_deassert(combophy->phy_reset);
+
+ ret = regmap_read_poll_timeout(combophy->regmap, SYSCFG_COMBOPHY_SR, val,
+ !(val & STM32MP25_PIPE0_PHYSTATUS),
+ 10, 1000);
+ if (ret) {
+ dev_err(combophy->dev, "timeout, cannot lock PLL\n");
+ goto out;
+ }
+
+ if (combophy->type == PHY_TYPE_PCIE) {
+ val = readl_relaxed(combophy->base + COMBOPHY_SUP_ANA_MPLL_LOOP_CTL);
+ val &= ~COMBOPHY_PROP_CNTRL;
+ val |= propcntrl;
+ writel_relaxed(val, combophy->base + COMBOPHY_SUP_ANA_MPLL_LOOP_CTL);
+ }
+
+ return 0;
+
+out:
+ if (combophy->type == PHY_TYPE_PCIE && !combophy->pad_clk)
+ regmap_update_bits(combophy->regmap, SYSCFG_PCIEPRGCR,
+ STM32MP25_PCIEPRGCR_EN, 0);
+
+ if (combophy->type != PHY_TYPE_PCIE)
+ regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR1,
+ SYSCFG_COMBOPHY_CR1_REFSSPEN, 0);
+
+ regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR2,
+ SYSCFG_COMBOPHY_CR2_ISO_DIS, 0);
+
+ return ret;
+}
+
+static struct phy *stm32_combophy_xlate(struct device *dev,
+ const struct of_phandle_args *args)
+{
+ struct stm32_combophy *combophy = dev_get_drvdata(dev);
+ unsigned int type;
+
+ if (args->args_count != 1) {
+ dev_err(dev, "invalid number of cells in 'phy' property\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ type = args->args[0];
+ if (type != PHY_TYPE_USB3 && type != PHY_TYPE_PCIE) {
+ dev_err(dev, "unsupported device type: %d\n", type);
+ return ERR_PTR(-EINVAL);
+ }
+
+ if (combophy->pad_clk && type != PHY_TYPE_PCIE) {
+ dev_err(dev, "Invalid use of clk_pad for USB3 mode\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ combophy->type = type;
+
+ return combophy->phy;
+}
+
+static int stm32_combophy_set_mode(struct stm32_combophy *combophy)
+{
+ int type = combophy->type;
+ u32 val;
+
+ switch (type) {
+ case PHY_TYPE_PCIE:
+ dev_dbg(combophy->dev, "setting PCIe ComboPHY\n");
+ val = COMBOPHY_MODESEL_PCIE;
+ break;
+ case PHY_TYPE_USB3:
+ dev_dbg(combophy->dev, "setting USB3 ComboPHY\n");
+ val = COMBOPHY_MODESEL_USB;
+ break;
+ default:
+ dev_err(combophy->dev, "Invalid PHY mode %d\n", type);
+ return -EINVAL;
+ }
+
+ return regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR2,
+ SYSCFG_COMBOPHY_CR2_MODESEL, val);
+}
+
+static int stm32_combophy_enable_clocks(struct stm32_combophy *combophy)
+{
+ int ret;
+
+ ret = clk_prepare_enable(combophy->phy_clk);
+ if (ret) {
+ dev_err(combophy->dev, "Core clock enable failed %d\n", ret);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(combophy->ker_clk);
+ if (ret) {
+ dev_err(combophy->dev, "ker_usb3pcie clock enable failed %d\n", ret);
+ clk_disable_unprepare(combophy->phy_clk);
+ return ret;
+ }
+
+ if (combophy->pad_clk) {
+ ret = clk_prepare_enable(combophy->pad_clk);
+ if (ret) {
+ dev_err(combophy->dev, "External clock enable failed %d\n", ret);
+ clk_disable_unprepare(combophy->ker_clk);
+ clk_disable_unprepare(combophy->phy_clk);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static void stm32_combophy_disable_clocks(struct stm32_combophy *combophy)
+{
+ if (combophy->pad_clk)
+ clk_disable_unprepare(combophy->pad_clk);
+ clk_disable_unprepare(combophy->ker_clk);
+ clk_disable_unprepare(combophy->phy_clk);
+}
+
+static int stm32_combophy_suspend_noirq(struct device *dev)
+{
+ struct stm32_combophy *combophy = dev_get_drvdata(dev);
+
+ /*
+ * Clocks should be turned off since it is not needed for
+ * wakeup capability. In case usb-remote wakeup is not enabled,
+ * combo-phy is already turned off by HCD driver using exit callback
+ */
+ if (combophy->is_init) {
+ stm32_combophy_disable_clocks(combophy);
+
+ /* since wakeup is enabled for ctrl */
+ enable_irq_wake(combophy->irq_wakeup);
+ }
+
+ return 0;
+}
+
+static int stm32_combophy_resume_noirq(struct device *dev)
+{
+ struct stm32_combophy *combophy = dev_get_drvdata(dev);
+ int ret;
+
+ /*
+ * If clocks was turned off by suspend call for wakeup then needs
+ * to be turned back ON in resume. In case usb-remote wakeup is not
+ * enabled, clocks already turned ON by HCD driver using init callback
+ */
+ if (combophy->is_init) {
+ /* since wakeup was enabled for ctrl */
+ disable_irq_wake(combophy->irq_wakeup);
+
+ ret = stm32_combophy_enable_clocks(combophy);
+ if (ret) {
+ dev_err(dev, "can't enable clocks (%d)\n", ret);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static int stm32_combophy_exit(struct phy *phy)
+{
+ struct stm32_combophy *combophy = phy_get_drvdata(phy);
+ struct device *dev = combophy->dev;
+
+ combophy->is_init = false;
+
+ if (combophy->type == PHY_TYPE_PCIE && !combophy->pad_clk)
+ regmap_update_bits(combophy->regmap, SYSCFG_PCIEPRGCR,
+ STM32MP25_PCIEPRGCR_EN, 0);
+
+ if (combophy->type != PHY_TYPE_PCIE)
+ regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR1,
+ SYSCFG_COMBOPHY_CR1_REFSSPEN, 0);
+
+ regmap_update_bits(combophy->regmap, SYSCFG_COMBOPHY_CR2,
+ SYSCFG_COMBOPHY_CR2_ISO_DIS, 0);
+
+ stm32_combophy_disable_clocks(combophy);
+
+ pm_runtime_put_noidle(dev);
+
+ return 0;
+}
+
+static int stm32_combophy_init(struct phy *phy)
+{
+ struct stm32_combophy *combophy = phy_get_drvdata(phy);
+ struct device *dev = combophy->dev;
+ int ret;
+
+ pm_runtime_get_noresume(dev);
+
+ ret = stm32_combophy_enable_clocks(combophy);
+ if (ret) {
+ dev_err(dev, "Clock enable failed %d\n", ret);
+ pm_runtime_put_noidle(dev);
+ return ret;
+ }
+
+ ret = stm32_combophy_set_mode(combophy);
+ if (ret) {
+ dev_err(dev, "combophy mode not set\n");
+ stm32_combophy_disable_clocks(combophy);
+ pm_runtime_put_noidle(dev);
+ return ret;
+ }
+
+ ret = stm32_combophy_pll_init(combophy);
+ if (ret) {
+ stm32_combophy_disable_clocks(combophy);
+ pm_runtime_put_noidle(dev);
+ return ret;
+ }
+
+ pm_runtime_disable(dev);
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
+
+ combophy->is_init = true;
+
+ return ret;
+}
+
+static const struct phy_ops stm32_combophy_phy_data = {
+ .init = stm32_combophy_init,
+ .exit = stm32_combophy_exit,
+ .owner = THIS_MODULE
+};
+
+static irqreturn_t stm32_combophy_irq_wakeup_handler(int irq, void *dev_id)
+{
+ return IRQ_HANDLED;
+}
+
+static int stm32_combophy_probe(struct platform_device *pdev)
+{
+ struct stm32_combophy *combophy;
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct phy_provider *phy_provider;
+ int ret, irq;
+
+ combophy = devm_kzalloc(dev, sizeof(*combophy), GFP_KERNEL);
+ if (!combophy)
+ return -ENOMEM;
+
+ combophy->dev = dev;
+
+ dev_set_drvdata(dev, combophy);
+
+ combophy->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(combophy->base))
+ return PTR_ERR(combophy->base);
+
+ combophy->phy_clk = devm_clk_get(dev, "apb-clk");
+ if (IS_ERR(combophy->phy_clk))
+ return dev_err_probe(dev, PTR_ERR(combophy->phy_clk),
+ "Failed to get PHY clock source\n");
+
+ combophy->ker_clk = devm_clk_get(dev, "ker-clk");
+ if (IS_ERR(combophy->ker_clk))
+ return dev_err_probe(dev, PTR_ERR(combophy->ker_clk),
+ "Failed to get PHY internal clock source\n");
+
+ combophy->pad_clk = devm_clk_get_optional(dev, "pad-clk");
+ if (IS_ERR(combophy->pad_clk))
+ return dev_err_probe(dev, PTR_ERR(combophy->pad_clk),
+ "Failed to get PHY external clock source\n");
+
+ combophy->phy_reset = devm_reset_control_get(dev, "phy-rst");
+ if (IS_ERR(combophy->phy_reset))
+ return dev_err_probe(dev, PTR_ERR(combophy->phy_reset),
+ "Failed to get PHY reset\n");
+
+ combophy->regmap = syscon_regmap_lookup_by_phandle(np, "st,syscfg");
+ if (IS_ERR(combophy->regmap))
+ return dev_err_probe(dev, PTR_ERR(combophy->regmap),
+ "No syscfg phandle specified\n");
+
+ combophy->phy = devm_phy_create(dev, NULL, &stm32_combophy_phy_data);
+ if (IS_ERR(combophy->phy))
+ return dev_err_probe(dev, PTR_ERR(combophy->phy),
+ "failed to create PCIe/USB3 ComboPHY\n");
+
+ if (device_property_read_bool(dev, "wakeup-source")) {
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return dev_err_probe(dev, irq, "failed to get IRQ\n");
+ combophy->irq_wakeup = irq;
+
+ ret = devm_request_threaded_irq(dev, combophy->irq_wakeup, NULL,
+ stm32_combophy_irq_wakeup_handler, IRQF_ONESHOT,
+ NULL, NULL);
+ if (ret)
+ return dev_err_probe(dev, ret, "unable to request wake IRQ %d\n",
+ combophy->irq_wakeup);
+ }
+
+ ret = devm_pm_runtime_enable(dev);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to enable pm runtime\n");
+
+ phy_set_drvdata(combophy->phy, combophy);
+
+ phy_provider = devm_of_phy_provider_register(dev, stm32_combophy_xlate);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct dev_pm_ops stm32_combophy_pm_ops = {
+ NOIRQ_SYSTEM_SLEEP_PM_OPS(stm32_combophy_suspend_noirq,
+ stm32_combophy_resume_noirq)
+};
+
+static const struct of_device_id stm32_combophy_of_match[] = {
+ { .compatible = "st,stm32mp25-combophy", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, stm32_combophy_of_match);
+
+static struct platform_driver stm32_combophy_driver = {
+ .probe = stm32_combophy_probe,
+ .driver = {
+ .name = "stm32-combophy",
+ .of_match_table = stm32_combophy_of_match,
+ .pm = pm_sleep_ptr(&stm32_combophy_pm_ops)
+ }
+};
+
+module_platform_driver(stm32_combophy_driver);
+
+MODULE_AUTHOR("Christian Bruel <christian.bruel@foss.st.com>");
+MODULE_DESCRIPTION("STM32MP25 Combophy USB3/PCIe controller driver");
+MODULE_LICENSE("GPL");
Addition of the COMBOPHY driver found on STM32MP25 platforms This single lane PHY is shared (exclusive) between the USB3 and PCIE controllers. Supports 5Gbit/s for PCIE gen2 or 2.5Gbit/s for PCIE gen1. Supports wakeup-source capability to wakeup system using remote-wakeup capable USB device Signed-off-by: Christian Bruel <christian.bruel@foss.st.com> --- drivers/phy/st/Kconfig | 11 + drivers/phy/st/Makefile | 1 + drivers/phy/st/phy-stm32-combophy.c | 607 ++++++++++++++++++++++++++++ 3 files changed, 619 insertions(+) create mode 100644 drivers/phy/st/phy-stm32-combophy.c