| Message ID | 20240816132058.920870-3-christian.bruel@foss.st.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add STM32MP25 USB3/PCIE COMBOPHY driver | expand |
On Fri, Aug 16, 2024 at 03:20:54PM +0200, Christian Bruel wrote: > Document the bindings for STM32 COMBOPHY interface, used to support > the PCIe and USB3 stm32mp25 drivers. > Following entries can be used to tune caracterisation parameters > - st,output-micro-ohms and st,output-vswing-microvolt bindings entries > to tune the impedance and voltage swing using discrete simulation results > - st,rx-equalizer register to set the internal rx equalizer filter value. > > Signed-off-by: Christian Bruel <christian.bruel@foss.st.com> > --- > .../bindings/phy/st,stm32-combophy.yaml | 144 ++++++++++++++++++ > 1 file changed, 144 insertions(+) > create mode 100644 Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml > > diff --git a/Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml b/Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml > new file mode 100644 > index 000000000000..c33a843b83a3 > --- /dev/null > +++ b/Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml > @@ -0,0 +1,144 @@ > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/phy/st,stm32-combophy.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: STMicroelectronics STM32MP25 USB3/PCIe COMBOPHY > + > +maintainers: > + - Christian Bruel <christian.bruel@foss.st.com> > + > +description: > + Single lane PHY shared (exclusive) between the USB3 and PCIe controllers. > + Supports 5Gbit/s for USB3 and PCIe gen2 or 2.5Gbit/s for PCIe gen1. > + > +properties: > + compatible: > + const: st,stm32mp25-combophy > + > + reg: > + maxItems: 1 > + > + "#phy-cells": > + const: 1 > + description: | > + The cells contain the following arguments. > + > + - description: The PHY type > + enum: > + - PHY_TYPE_USB3 > + - PHY_TYPE_PCIE > + > + clocks: > + minItems: 2 > + items: > + - description: apb Bus clock mandatory to access registers. > + - description: ker Internal RCC reference clock for USB3 or PCIe > + - description: pad Optional on board clock input for PCIe only. Typically an > + external 100Mhz oscillator wired on dedicated CLKIN pad. Used as reference > + clock input instead of the ker > + > + clock-names: > + minItems: 2 > + items: > + - const: apb > + - const: ker > + - const: pad > + > + resets: > + maxItems: 1 > + > + reset-names: > + const: phy > + > + power-domains: > + maxItems: 1 > + > + wakeup-source: true > + > + interrupts: > + maxItems: 1 > + description: interrupt used for wakeup > + > + access-controllers: > + minItems: 1 > + maxItems: 2 > + > + st,syscfg: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: Phandle to the SYSCON entry required for configuring PCIe > + or USB3. > + > + st,ssc-on: > + type: boolean > + description: > + A boolean property whose presence indicates that the SSC for common clock > + needs to be set. > + > + st,rx-equalizer: > + $ref: /schemas/types.yaml#/definitions/uint32 > + minimum: 0 > + maximum: 7 > + default: 2 > + description: > + A 3 bit value to tune the RX fixed equalizer setting for optimal eye compliance > + > + st,output-micro-ohms: > + minimum: 3999000 > + maximum: 6090000 > + default: 4968000 > + description: > + A value property to tune the Single Ended Output Impedance, simulations results > + at 25C for a VDDP=0.8V. The hardware accepts discrete values in this range. > + > + st,output-vswing-microvolt: > + minimum: 442000 > + maximum: 803000 > + default: 803000 > + description: > + A value property in microvolt to tune the Single Ended Output Voltage Swing to change the > + Vlo, Vhi for a VDDP = 0.8V. The hardware accepts discrete values in this range. > + > +required: > + - compatible > + - reg > + - st,syscfg > + - '#phy-cells' > + - resets > + - reset-names > + - clocks > + - clock-names > + > +allOf: > + - if: > + required: > + - wakeup-source > + then: > + anyOf: > + - required: [interrupts] > + - required: [interrupts-extended] Drop this if/then. We should have this somewhere common as it applies to all. Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
diff --git a/Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml b/Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml new file mode 100644 index 000000000000..c33a843b83a3 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml @@ -0,0 +1,144 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/st,stm32-combophy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STM32MP25 USB3/PCIe COMBOPHY + +maintainers: + - Christian Bruel <christian.bruel@foss.st.com> + +description: + Single lane PHY shared (exclusive) between the USB3 and PCIe controllers. + Supports 5Gbit/s for USB3 and PCIe gen2 or 2.5Gbit/s for PCIe gen1. + +properties: + compatible: + const: st,stm32mp25-combophy + + reg: + maxItems: 1 + + "#phy-cells": + const: 1 + description: | + The cells contain the following arguments. + + - description: The PHY type + enum: + - PHY_TYPE_USB3 + - PHY_TYPE_PCIE + + clocks: + minItems: 2 + items: + - description: apb Bus clock mandatory to access registers. + - description: ker Internal RCC reference clock for USB3 or PCIe + - description: pad Optional on board clock input for PCIe only. Typically an + external 100Mhz oscillator wired on dedicated CLKIN pad. Used as reference + clock input instead of the ker + + clock-names: + minItems: 2 + items: + - const: apb + - const: ker + - const: pad + + resets: + maxItems: 1 + + reset-names: + const: phy + + power-domains: + maxItems: 1 + + wakeup-source: true + + interrupts: + maxItems: 1 + description: interrupt used for wakeup + + access-controllers: + minItems: 1 + maxItems: 2 + + st,syscfg: + $ref: /schemas/types.yaml#/definitions/phandle + description: Phandle to the SYSCON entry required for configuring PCIe + or USB3. + + st,ssc-on: + type: boolean + description: + A boolean property whose presence indicates that the SSC for common clock + needs to be set. + + st,rx-equalizer: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 7 + default: 2 + description: + A 3 bit value to tune the RX fixed equalizer setting for optimal eye compliance + + st,output-micro-ohms: + minimum: 3999000 + maximum: 6090000 + default: 4968000 + description: + A value property to tune the Single Ended Output Impedance, simulations results + at 25C for a VDDP=0.8V. The hardware accepts discrete values in this range. + + st,output-vswing-microvolt: + minimum: 442000 + maximum: 803000 + default: 803000 + description: + A value property in microvolt to tune the Single Ended Output Voltage Swing to change the + Vlo, Vhi for a VDDP = 0.8V. The hardware accepts discrete values in this range. + +required: + - compatible + - reg + - st,syscfg + - '#phy-cells' + - resets + - reset-names + - clocks + - clock-names + +allOf: + - if: + required: + - wakeup-source + then: + anyOf: + - required: [interrupts] + - required: [interrupts-extended] + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/st,stm32mp25-rcc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/reset/st,stm32mp25-rcc.h> + + combophy: phy@480c0000 { + compatible = "st,stm32mp25-combophy"; + reg = <0x480c0000 0x1000>; + #phy-cells = <1>; + clocks = <&rcc CK_BUS_USB3PCIEPHY>, <&rcc CK_KER_USB3PCIEPHY>; + clock-names = "apb", "ker"; + resets = <&rcc USB3PCIEPHY_R>; + reset-names = "phy"; + st,syscfg = <&syscfg>; + access-controllers = <&rifsc 67>; + power-domains = <&CLUSTER_PD>; + wakeup-source; + interrupts-extended = <&exti1 45 IRQ_TYPE_EDGE_FALLING>; + }; +...
Document the bindings for STM32 COMBOPHY interface, used to support the PCIe and USB3 stm32mp25 drivers. Following entries can be used to tune caracterisation parameters - st,output-micro-ohms and st,output-vswing-microvolt bindings entries to tune the impedance and voltage swing using discrete simulation results - st,rx-equalizer register to set the internal rx equalizer filter value. Signed-off-by: Christian Bruel <christian.bruel@foss.st.com> --- .../bindings/phy/st,stm32-combophy.yaml | 144 ++++++++++++++++++ 1 file changed, 144 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml