| Message ID | 20240822152801.602318-11-claudiu.beznea.uj@bp.renesas.com |
|---|---|
| State | Accepted |
| Commit | 4eae16375357a2a7e8501be5469532f7636064b3 |
| Headers | show |
| Series | Add initial USB support for the Renesas RZ/G3S SoC | expand |
Hi Claudiu, > -----Original Message----- > From: Claudiu <claudiu.beznea@tuxon.dev> > Sent: Thursday, August 22, 2024 4:28 PM > Subject: [PATCH 10/16] phy: renesas: rcar-gen3-usb2: Add support to initialize the bus > > From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> > > The Renesas RZ/G3S need to initialize the USB BUS before transferring data due to hardware limitation. > As the register that need to be touched for this is in the address space of the USB PHY, and the UBS > PHY need to be initialized before any other USB drivers handling data transfer, add support to > initialize the USB BUS. > > As the USB PHY is probed before any other USB drivers that enables clocks and de-assert the reset > signals and the BUS initialization is done in the probe phase, we need to add code to de-assert reset > signal and runtime resume the device (which enables its clocks) before accessing the registers. > > As the reset signals are not required by the USB PHY driver for the other USB PHY hardware variants, > the reset signals and runtime PM was handled only in the function that initialize the USB BUS. > > The PHY initialization was done right after runtime PM enable to have all in place when the PHYs are > registered. There is no user for this patch. The first user is RZ/G3S and you should merge this patch with next one. Cheers, Biju > > Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> > --- > drivers/phy/renesas/phy-rcar-gen3-usb2.c | 50 ++++++++++++++++++++++-- > 1 file changed, 47 insertions(+), 3 deletions(-) > > diff --git a/drivers/phy/renesas/phy-rcar-gen3-usb2.c b/drivers/phy/renesas/phy-rcar-gen3-usb2.c > index 7594f64eb737..cf4299cea579 100644 > --- a/drivers/phy/renesas/phy-rcar-gen3-usb2.c > +++ b/drivers/phy/renesas/phy-rcar-gen3-usb2.c > @@ -19,12 +19,14 @@ > #include <linux/platform_device.h> > #include <linux/pm_runtime.h> > #include <linux/regulator/consumer.h> > +#include <linux/reset.h> > #include <linux/string.h> > #include <linux/usb/of.h> > #include <linux/workqueue.h> > > /******* USB2.0 Host registers (original offset is +0x200) *******/ > #define USB2_INT_ENABLE 0x000 > +#define USB2_AHB_BUS_CTR 0x008 > #define USB2_USBCTR 0x00c > #define USB2_SPD_RSM_TIMSET 0x10c > #define USB2_OC_TIMSET 0x110 > @@ -40,6 +42,10 @@ > #define USB2_INT_ENABLE_USBH_INTB_EN BIT(2) /* For EHCI */ > #define USB2_INT_ENABLE_USBH_INTA_EN BIT(1) /* For OHCI */ > > +/* AHB_BUS_CTR */ > +#define USB2_AHB_BUS_CTR_MBL_MASK GENMASK(1, 0) > +#define USB2_AHB_BUS_CTR_MBL_INCR4 2 > + > /* USBCTR */ > #define USB2_USBCTR_DIRPD BIT(2) > #define USB2_USBCTR_PLL_RST BIT(1) > @@ -111,6 +117,7 @@ struct rcar_gen3_chan { > struct extcon_dev *extcon; > struct rcar_gen3_phy rphys[NUM_OF_PHYS]; > struct regulator *vbus; > + struct reset_control *rstc; > struct work_struct work; > struct mutex lock; /* protects rphys[...].powered */ > enum usb_dr_mode dr_mode; > @@ -125,6 +132,7 @@ struct rcar_gen3_chan { struct rcar_gen3_phy_drv_data { > const struct phy_ops *phy_usb2_ops; > bool no_adp_ctrl; > + bool init_bus; > }; > > /* > @@ -650,6 +658,35 @@ static enum usb_dr_mode rcar_gen3_get_dr_mode(struct device_node *np) > return candidate; > } > > +static int rcar_gen3_phy_usb2_init_bus(struct rcar_gen3_chan *channel) > +{ > + struct device *dev = channel->dev; > + int ret; > + u32 val; > + > + channel->rstc = devm_reset_control_array_get_shared(dev); > + if (IS_ERR(channel->rstc)) > + return PTR_ERR(channel->rstc); > + > + ret = pm_runtime_resume_and_get(dev); > + if (ret) > + return ret; > + > + ret = reset_control_deassert(channel->rstc); > + if (ret) > + goto rpm_put; > + > + val = readl(channel->base + USB2_AHB_BUS_CTR); > + val &= ~USB2_AHB_BUS_CTR_MBL_MASK; > + val |= USB2_AHB_BUS_CTR_MBL_INCR4; > + writel(val, channel->base + USB2_AHB_BUS_CTR); > + > +rpm_put: > + pm_runtime_put(dev); > + > + return ret; > +} > + > static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) { > const struct rcar_gen3_phy_drv_data *phy_data; @@ -703,6 +740,15 @@ static int > rcar_gen3_phy_usb2_probe(struct platform_device *pdev) > goto error; > } > > + platform_set_drvdata(pdev, channel); > + channel->dev = dev; > + > + if (phy_data->init_bus) { > + ret = rcar_gen3_phy_usb2_init_bus(channel); > + if (ret) > + goto error; > + } > + > channel->soc_no_adp_ctrl = phy_data->no_adp_ctrl; > if (phy_data->no_adp_ctrl) > channel->obint_enable_bits = USB2_OBINT_IDCHG_EN; @@ -733,9 +779,6 @@ static int > rcar_gen3_phy_usb2_probe(struct platform_device *pdev) > channel->vbus = NULL; > } > > - platform_set_drvdata(pdev, channel); > - channel->dev = dev; > - > provider = devm_of_phy_provider_register(dev, rcar_gen3_phy_usb2_xlate); > if (IS_ERR(provider)) { > dev_err(dev, "Failed to register PHY provider\n"); @@ -762,6 +805,7 @@ static void > rcar_gen3_phy_usb2_remove(struct platform_device *pdev) > if (channel->is_otg_channel) > device_remove_file(&pdev->dev, &dev_attr_role); > > + reset_control_assert(channel->rstc); > pm_runtime_disable(&pdev->dev); > }; > > -- > 2.39.2
Hi, Biju, On 23.08.2024 10:35, Biju Das wrote: > Hi Claudiu, > >> -----Original Message----- >> From: Claudiu <claudiu.beznea@tuxon.dev> >> Sent: Thursday, August 22, 2024 4:28 PM >> Subject: [PATCH 10/16] phy: renesas: rcar-gen3-usb2: Add support to initialize the bus >> >> From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> >> >> The Renesas RZ/G3S need to initialize the USB BUS before transferring data due to hardware limitation. >> As the register that need to be touched for this is in the address space of the USB PHY, and the UBS >> PHY need to be initialized before any other USB drivers handling data transfer, add support to >> initialize the USB BUS. >> >> As the USB PHY is probed before any other USB drivers that enables clocks and de-assert the reset >> signals and the BUS initialization is done in the probe phase, we need to add code to de-assert reset >> signal and runtime resume the device (which enables its clocks) before accessing the registers. >> >> As the reset signals are not required by the USB PHY driver for the other USB PHY hardware variants, >> the reset signals and runtime PM was handled only in the function that initialize the USB BUS. >> >> The PHY initialization was done right after runtime PM enable to have all in place when the PHYs are >> registered. > > There is no user for this patch. The first user is RZ/G3S and you should merge this patch with > next one. I think this is a matter of taste... This is how I usually format the patches (for scenarios like this) and got no request for squashing. Anyway, I can do it your way, too. Thank you, Claudiu Beznea > > Cheers, > Biju > >> >> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> >> --- >> drivers/phy/renesas/phy-rcar-gen3-usb2.c | 50 ++++++++++++++++++++++-- >> 1 file changed, 47 insertions(+), 3 deletions(-) >> >> diff --git a/drivers/phy/renesas/phy-rcar-gen3-usb2.c b/drivers/phy/renesas/phy-rcar-gen3-usb2.c >> index 7594f64eb737..cf4299cea579 100644 >> --- a/drivers/phy/renesas/phy-rcar-gen3-usb2.c >> +++ b/drivers/phy/renesas/phy-rcar-gen3-usb2.c >> @@ -19,12 +19,14 @@ >> #include <linux/platform_device.h> >> #include <linux/pm_runtime.h> >> #include <linux/regulator/consumer.h> >> +#include <linux/reset.h> >> #include <linux/string.h> >> #include <linux/usb/of.h> >> #include <linux/workqueue.h> >> >> /******* USB2.0 Host registers (original offset is +0x200) *******/ >> #define USB2_INT_ENABLE 0x000 >> +#define USB2_AHB_BUS_CTR 0x008 >> #define USB2_USBCTR 0x00c >> #define USB2_SPD_RSM_TIMSET 0x10c >> #define USB2_OC_TIMSET 0x110 >> @@ -40,6 +42,10 @@ >> #define USB2_INT_ENABLE_USBH_INTB_EN BIT(2) /* For EHCI */ >> #define USB2_INT_ENABLE_USBH_INTA_EN BIT(1) /* For OHCI */ >> >> +/* AHB_BUS_CTR */ >> +#define USB2_AHB_BUS_CTR_MBL_MASK GENMASK(1, 0) >> +#define USB2_AHB_BUS_CTR_MBL_INCR4 2 >> + >> /* USBCTR */ >> #define USB2_USBCTR_DIRPD BIT(2) >> #define USB2_USBCTR_PLL_RST BIT(1) >> @@ -111,6 +117,7 @@ struct rcar_gen3_chan { >> struct extcon_dev *extcon; >> struct rcar_gen3_phy rphys[NUM_OF_PHYS]; >> struct regulator *vbus; >> + struct reset_control *rstc; >> struct work_struct work; >> struct mutex lock; /* protects rphys[...].powered */ >> enum usb_dr_mode dr_mode; >> @@ -125,6 +132,7 @@ struct rcar_gen3_chan { struct rcar_gen3_phy_drv_data { >> const struct phy_ops *phy_usb2_ops; >> bool no_adp_ctrl; >> + bool init_bus; >> }; >> >> /* >> @@ -650,6 +658,35 @@ static enum usb_dr_mode rcar_gen3_get_dr_mode(struct device_node *np) >> return candidate; >> } >> >> +static int rcar_gen3_phy_usb2_init_bus(struct rcar_gen3_chan *channel) >> +{ >> + struct device *dev = channel->dev; >> + int ret; >> + u32 val; >> + >> + channel->rstc = devm_reset_control_array_get_shared(dev); >> + if (IS_ERR(channel->rstc)) >> + return PTR_ERR(channel->rstc); >> + >> + ret = pm_runtime_resume_and_get(dev); >> + if (ret) >> + return ret; >> + >> + ret = reset_control_deassert(channel->rstc); >> + if (ret) >> + goto rpm_put; >> + >> + val = readl(channel->base + USB2_AHB_BUS_CTR); >> + val &= ~USB2_AHB_BUS_CTR_MBL_MASK; >> + val |= USB2_AHB_BUS_CTR_MBL_INCR4; >> + writel(val, channel->base + USB2_AHB_BUS_CTR); >> + >> +rpm_put: >> + pm_runtime_put(dev); >> + >> + return ret; >> +} >> + >> static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) { >> const struct rcar_gen3_phy_drv_data *phy_data; @@ -703,6 +740,15 @@ static int >> rcar_gen3_phy_usb2_probe(struct platform_device *pdev) >> goto error; >> } >> >> + platform_set_drvdata(pdev, channel); >> + channel->dev = dev; >> + >> + if (phy_data->init_bus) { >> + ret = rcar_gen3_phy_usb2_init_bus(channel); >> + if (ret) >> + goto error; >> + } >> + >> channel->soc_no_adp_ctrl = phy_data->no_adp_ctrl; >> if (phy_data->no_adp_ctrl) >> channel->obint_enable_bits = USB2_OBINT_IDCHG_EN; @@ -733,9 +779,6 @@ static int >> rcar_gen3_phy_usb2_probe(struct platform_device *pdev) >> channel->vbus = NULL; >> } >> >> - platform_set_drvdata(pdev, channel); >> - channel->dev = dev; >> - >> provider = devm_of_phy_provider_register(dev, rcar_gen3_phy_usb2_xlate); >> if (IS_ERR(provider)) { >> dev_err(dev, "Failed to register PHY provider\n"); @@ -762,6 +805,7 @@ static void >> rcar_gen3_phy_usb2_remove(struct platform_device *pdev) >> if (channel->is_otg_channel) >> device_remove_file(&pdev->dev, &dev_attr_role); >> >> + reset_control_assert(channel->rstc); >> pm_runtime_disable(&pdev->dev); >> }; >> >> -- >> 2.39.2 >
Hi Claudiu, > -----Original Message----- > From: claudiu beznea <claudiu.beznea@tuxon.dev> > Sent: Friday, August 23, 2024 9:58 AM - > clk@vger.kernel.org; linux-pm@vger.kernel.org; Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> > Subject: Re: [PATCH 10/16] phy: renesas: rcar-gen3-usb2: Add support to initialize the bus > > Hi, Biju, > > On 23.08.2024 10:35, Biju Das wrote: > > Hi Claudiu, > > > >> -----Original Message----- > >> From: Claudiu <claudiu.beznea@tuxon.dev> > >> Sent: Thursday, August 22, 2024 4:28 PM > >> Subject: [PATCH 10/16] phy: renesas: rcar-gen3-usb2: Add support to > >> initialize the bus > >> > >> From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> > >> > >> The Renesas RZ/G3S need to initialize the USB BUS before transferring data due to hardware > limitation. > >> As the register that need to be touched for this is in the address > >> space of the USB PHY, and the UBS PHY need to be initialized before > >> any other USB drivers handling data transfer, add support to initialize the USB BUS. > >> > >> As the USB PHY is probed before any other USB drivers that enables > >> clocks and de-assert the reset signals and the BUS initialization is > >> done in the probe phase, we need to add code to de-assert reset signal and runtime resume the > device (which enables its clocks) before accessing the registers. > >> > >> As the reset signals are not required by the USB PHY driver for the > >> other USB PHY hardware variants, the reset signals and runtime PM was handled only in the function > that initialize the USB BUS. > >> > >> The PHY initialization was done right after runtime PM enable to have > >> all in place when the PHYs are registered. > > > > There is no user for this patch. The first user is RZ/G3S and you > > should merge this patch with next one. > > I think this is a matter of taste... This is how I usually format the patches (for scenarios like > this) and got no request for squashing. That is strange for trivial patches like this. Cheers, Biju > > > >> > >> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> > >> --- > >> drivers/phy/renesas/phy-rcar-gen3-usb2.c | 50 > >> ++++++++++++++++++++++-- > >> 1 file changed, 47 insertions(+), 3 deletions(-) > >> > >> diff --git a/drivers/phy/renesas/phy-rcar-gen3-usb2.c > >> b/drivers/phy/renesas/phy-rcar-gen3-usb2.c > >> index 7594f64eb737..cf4299cea579 100644 > >> --- a/drivers/phy/renesas/phy-rcar-gen3-usb2.c > >> +++ b/drivers/phy/renesas/phy-rcar-gen3-usb2.c > >> @@ -19,12 +19,14 @@ > >> #include <linux/platform_device.h> > >> #include <linux/pm_runtime.h> > >> #include <linux/regulator/consumer.h> > >> +#include <linux/reset.h> > >> #include <linux/string.h> > >> #include <linux/usb/of.h> > >> #include <linux/workqueue.h> > >> > >> /******* USB2.0 Host registers (original offset is +0x200) *******/ > >> #define USB2_INT_ENABLE 0x000 > >> +#define USB2_AHB_BUS_CTR 0x008 > >> #define USB2_USBCTR 0x00c > >> #define USB2_SPD_RSM_TIMSET 0x10c > >> #define USB2_OC_TIMSET 0x110 > >> @@ -40,6 +42,10 @@ > >> #define USB2_INT_ENABLE_USBH_INTB_EN BIT(2) /* For EHCI */ > >> #define USB2_INT_ENABLE_USBH_INTA_EN BIT(1) /* For OHCI */ > >> > >> +/* AHB_BUS_CTR */ > >> +#define USB2_AHB_BUS_CTR_MBL_MASK GENMASK(1, 0) > >> +#define USB2_AHB_BUS_CTR_MBL_INCR4 2 > >> + > >> /* USBCTR */ > >> #define USB2_USBCTR_DIRPD BIT(2) > >> #define USB2_USBCTR_PLL_RST BIT(1) > >> @@ -111,6 +117,7 @@ struct rcar_gen3_chan { > >> struct extcon_dev *extcon; > >> struct rcar_gen3_phy rphys[NUM_OF_PHYS]; > >> struct regulator *vbus; > >> + struct reset_control *rstc; > >> struct work_struct work; > >> struct mutex lock; /* protects rphys[...].powered */ > >> enum usb_dr_mode dr_mode; > >> @@ -125,6 +132,7 @@ struct rcar_gen3_chan { struct rcar_gen3_phy_drv_data { > >> const struct phy_ops *phy_usb2_ops; > >> bool no_adp_ctrl; > >> + bool init_bus; > >> }; > >> > >> /* > >> @@ -650,6 +658,35 @@ static enum usb_dr_mode rcar_gen3_get_dr_mode(struct device_node *np) > >> return candidate; > >> } > >> > >> +static int rcar_gen3_phy_usb2_init_bus(struct rcar_gen3_chan > >> +*channel) { > >> + struct device *dev = channel->dev; > >> + int ret; > >> + u32 val; > >> + > >> + channel->rstc = devm_reset_control_array_get_shared(dev); > >> + if (IS_ERR(channel->rstc)) > >> + return PTR_ERR(channel->rstc); > >> + > >> + ret = pm_runtime_resume_and_get(dev); > >> + if (ret) > >> + return ret; > >> + > >> + ret = reset_control_deassert(channel->rstc); > >> + if (ret) > >> + goto rpm_put; > >> + > >> + val = readl(channel->base + USB2_AHB_BUS_CTR); > >> + val &= ~USB2_AHB_BUS_CTR_MBL_MASK; > >> + val |= USB2_AHB_BUS_CTR_MBL_INCR4; > >> + writel(val, channel->base + USB2_AHB_BUS_CTR); > >> + > >> +rpm_put: > >> + pm_runtime_put(dev); > >> + > >> + return ret; > >> +} > >> + > >> static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) { > >> const struct rcar_gen3_phy_drv_data *phy_data; @@ -703,6 +740,15 @@ > >> static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) > >> goto error; > >> } > >> > >> + platform_set_drvdata(pdev, channel); > >> + channel->dev = dev; > >> + > >> + if (phy_data->init_bus) { > >> + ret = rcar_gen3_phy_usb2_init_bus(channel); > >> + if (ret) > >> + goto error; > >> + } > >> + > >> channel->soc_no_adp_ctrl = phy_data->no_adp_ctrl; > >> if (phy_data->no_adp_ctrl) > >> channel->obint_enable_bits = USB2_OBINT_IDCHG_EN; @@ -733,9 +779,6 > >> @@ static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) > >> channel->vbus = NULL; > >> } > >> > >> - platform_set_drvdata(pdev, channel); > >> - channel->dev = dev; > >> - > >> provider = devm_of_phy_provider_register(dev, rcar_gen3_phy_usb2_xlate); > >> if (IS_ERR(provider)) { > >> dev_err(dev, "Failed to register PHY provider\n"); @@ -762,6 > >> +805,7 @@ static void rcar_gen3_phy_usb2_remove(struct platform_device *pdev) > >> if (channel->is_otg_channel) > >> device_remove_file(&pdev->dev, &dev_attr_role); > >> > >> + reset_control_assert(channel->rstc); > >> pm_runtime_disable(&pdev->dev); > >> }; > >> > >> -- > >> 2.39.2 > >
On 23-08-24, 09:01, Biju Das wrote: > > >> The Renesas RZ/G3S need to initialize the USB BUS before transferring data due to hardware > > limitation. > > >> As the register that need to be touched for this is in the address > > >> space of the USB PHY, and the UBS PHY need to be initialized before > > >> any other USB drivers handling data transfer, add support to initialize the USB BUS. > > >> > > >> As the USB PHY is probed before any other USB drivers that enables > > >> clocks and de-assert the reset signals and the BUS initialization is > > >> done in the probe phase, we need to add code to de-assert reset signal and runtime resume the > > device (which enables its clocks) before accessing the registers. > > >> > > >> As the reset signals are not required by the USB PHY driver for the > > >> other USB PHY hardware variants, the reset signals and runtime PM was handled only in the function > > that initialize the USB BUS. > > >> > > >> The PHY initialization was done right after runtime PM enable to have > > >> all in place when the PHYs are registered. > > > > > > There is no user for this patch. The first user is RZ/G3S and you > > > should merge this patch with next one. > > > > I think this is a matter of taste... This is how I usually format the patches (for scenarios like > > this) and got no request for squashing. > > That is strange for trivial patches like this. Splitting is better, this patch does one thing whereas the next one uses it adds in new device, i would say quite a clean approach NOTE: Don't quote the not required context while replying, it is good mail list hygiene
Hi Vinod, > -----Original Message----- > From: Vinod Koul <vkoul@kernel.org> > Sent: Friday, August 30, 2024 9:03 AM > Subject: Re: [PATCH 10/16] phy: renesas: rcar-gen3-usb2: Add support to initialize the bus > > On 23-08-24, 09:01, Biju Das wrote: > > > >> The Renesas RZ/G3S need to initialize the USB BUS before > > > >> transferring data due to hardware > > > limitation. > > > >> As the register that need to be touched for this is in the > > > >> address space of the USB PHY, and the UBS PHY need to be > > > >> initialized before any other USB drivers handling data transfer, add support to initialize the > USB BUS. > > > >> > > > >> As the USB PHY is probed before any other USB drivers that > > > >> enables clocks and de-assert the reset signals and the BUS > > > >> initialization is done in the probe phase, we need to add code to > > > >> de-assert reset signal and runtime resume the > > > device (which enables its clocks) before accessing the registers. > > > >> > > > >> As the reset signals are not required by the USB PHY driver for > > > >> the other USB PHY hardware variants, the reset signals and > > > >> runtime PM was handled only in the function > > > that initialize the USB BUS. > > > >> > > > >> The PHY initialization was done right after runtime PM enable to > > > >> have all in place when the PHYs are registered. > > > > > > > > There is no user for this patch. The first user is RZ/G3S and you > > > > should merge this patch with next one. > > > > > > I think this is a matter of taste... This is how I usually format > > > the patches (for scenarios like > > > this) and got no request for squashing. > > > > That is strange for trivial patches like this. > > Splitting is better, this patch does one thing whereas the next one uses it adds in new device, i > would say quite a clean approach > > NOTE: Don't quote the not required context while replying, it is good mail list hygiene Agreed. I was wrong then. To support a new device, bus initialization is required. So I thought it should go together. Cheers, Biju
Hi Claudiu, On Thu, Aug 22, 2024 at 5:28 PM Claudiu <claudiu.beznea@tuxon.dev> wrote: > > From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> > > The Renesas RZ/G3S need to initialize the USB BUS before transferring data > due to hardware limitation. As the register that need to be touched for > this is in the address space of the USB PHY, and the UBS PHY need to be > initialized before any other USB drivers handling data transfer, add > support to initialize the USB BUS. > > As the USB PHY is probed before any other USB drivers that enables > clocks and de-assert the reset signals and the BUS initialization is done > in the probe phase, we need to add code to de-assert reset signal and > runtime resume the device (which enables its clocks) before accessing > the registers. > > As the reset signals are not required by the USB PHY driver for the other > USB PHY hardware variants, the reset signals and runtime PM was handled > only in the function that initialize the USB BUS. > > The PHY initialization was done right after runtime PM enable to have > all in place when the PHYs are registered. > > Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Thanks for your patch, which is now commit 4eae16375357a2a7 ("phy: renesas: rcar-gen3-usb2: Add support to initialize the bus") in v6.12-rc1. > --- a/drivers/phy/renesas/phy-rcar-gen3-usb2.c > +++ b/drivers/phy/renesas/phy-rcar-gen3-usb2.c > @@ -650,6 +658,35 @@ static enum usb_dr_mode rcar_gen3_get_dr_mode(struct device_node *np) > return candidate; > } > > +static int rcar_gen3_phy_usb2_init_bus(struct rcar_gen3_chan *channel) > +{ > + struct device *dev = channel->dev; > + int ret; > + u32 val; > + > + channel->rstc = devm_reset_control_array_get_shared(dev); > + if (IS_ERR(channel->rstc)) > + return PTR_ERR(channel->rstc); > + > + ret = pm_runtime_resume_and_get(dev); > + if (ret) > + return ret; > + > + ret = reset_control_deassert(channel->rstc); > + if (ret) > + goto rpm_put; > + > + val = readl(channel->base + USB2_AHB_BUS_CTR); > + val &= ~USB2_AHB_BUS_CTR_MBL_MASK; > + val |= USB2_AHB_BUS_CTR_MBL_INCR4; > + writel(val, channel->base + USB2_AHB_BUS_CTR); > + > +rpm_put: > + pm_runtime_put(dev); > + > + return ret; > +} > + > static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) > { > const struct rcar_gen3_phy_drv_data *phy_data; > @@ -703,6 +740,15 @@ static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) > goto error; > } > > + platform_set_drvdata(pdev, channel); > + channel->dev = dev; Unrelated change? > + > + if (phy_data->init_bus) { > + ret = rcar_gen3_phy_usb2_init_bus(channel); > + if (ret) > + goto error; > + } > + > channel->soc_no_adp_ctrl = phy_data->no_adp_ctrl; > if (phy_data->no_adp_ctrl) > channel->obint_enable_bits = USB2_OBINT_IDCHG_EN; > @@ -733,9 +779,6 @@ static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) > channel->vbus = NULL; > } > > - platform_set_drvdata(pdev, channel); > - channel->dev = dev; > - > provider = devm_of_phy_provider_register(dev, rcar_gen3_phy_usb2_xlate); > if (IS_ERR(provider)) { > dev_err(dev, "Failed to register PHY provider\n"); The reset is not asserted in the error path, only in .remove(). Oh, Christophe already sent a fix for that... "[PATCH v3] phy: renesas: rcar-gen3-usb2: Fix an error handling path in rcar_gen3_phy_usb2_probe()" https://lore.kernel.org/all/290b25827e3f0742808940719455ff0c5cb9d01d.1726329925.git.christophe.jaillet@wanadoo.fr > @@ -762,6 +805,7 @@ static void rcar_gen3_phy_usb2_remove(struct platform_device *pdev) > if (channel->is_otg_channel) > device_remove_file(&pdev->dev, &dev_attr_role); > > + reset_control_assert(channel->rstc); > pm_runtime_disable(&pdev->dev); > }; The rest LGTM. Gr{oetje,eeting}s, Geert
Hi, Geert, On 08.10.2024 17:57, Geert Uytterhoeven wrote: > Hi Claudiu, > > On Thu, Aug 22, 2024 at 5:28 PM Claudiu <claudiu.beznea@tuxon.dev> wrote: >> >> From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> >> >> The Renesas RZ/G3S need to initialize the USB BUS before transferring data >> due to hardware limitation. As the register that need to be touched for >> this is in the address space of the USB PHY, and the UBS PHY need to be >> initialized before any other USB drivers handling data transfer, add >> support to initialize the USB BUS. >> >> As the USB PHY is probed before any other USB drivers that enables >> clocks and de-assert the reset signals and the BUS initialization is done >> in the probe phase, we need to add code to de-assert reset signal and >> runtime resume the device (which enables its clocks) before accessing >> the registers. >> >> As the reset signals are not required by the USB PHY driver for the other >> USB PHY hardware variants, the reset signals and runtime PM was handled >> only in the function that initialize the USB BUS. >> >> The PHY initialization was done right after runtime PM enable to have >> all in place when the PHYs are registered. >> >> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> > > Thanks for your patch, which is now commit 4eae16375357a2a7 ("phy: > renesas: rcar-gen3-usb2: Add support to initialize the bus") in > v6.12-rc1. > >> --- a/drivers/phy/renesas/phy-rcar-gen3-usb2.c >> +++ b/drivers/phy/renesas/phy-rcar-gen3-usb2.c >> @@ -650,6 +658,35 @@ static enum usb_dr_mode rcar_gen3_get_dr_mode(struct device_node *np) >> return candidate; >> } >> >> +static int rcar_gen3_phy_usb2_init_bus(struct rcar_gen3_chan *channel) >> +{ >> + struct device *dev = channel->dev; >> + int ret; >> + u32 val; >> + >> + channel->rstc = devm_reset_control_array_get_shared(dev); >> + if (IS_ERR(channel->rstc)) >> + return PTR_ERR(channel->rstc); >> + >> + ret = pm_runtime_resume_and_get(dev); >> + if (ret) >> + return ret; >> + >> + ret = reset_control_deassert(channel->rstc); >> + if (ret) >> + goto rpm_put; >> + >> + val = readl(channel->base + USB2_AHB_BUS_CTR); >> + val &= ~USB2_AHB_BUS_CTR_MBL_MASK; >> + val |= USB2_AHB_BUS_CTR_MBL_INCR4; >> + writel(val, channel->base + USB2_AHB_BUS_CTR); >> + >> +rpm_put: >> + pm_runtime_put(dev); >> + >> + return ret; >> +} >> + >> static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) >> { >> const struct rcar_gen3_phy_drv_data *phy_data; >> @@ -703,6 +740,15 @@ static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) >> goto error; >> } >> >> + platform_set_drvdata(pdev, channel); >> + channel->dev = dev; > > Unrelated change? That's a leftover from the removal of the suspend to RAM support from the initial work (internal only) of this series. I'll keep it in mid to remove it on the following patches, if needed. > >> + >> + if (phy_data->init_bus) { >> + ret = rcar_gen3_phy_usb2_init_bus(channel); >> + if (ret) >> + goto error; >> + } >> + >> channel->soc_no_adp_ctrl = phy_data->no_adp_ctrl; >> if (phy_data->no_adp_ctrl) >> channel->obint_enable_bits = USB2_OBINT_IDCHG_EN; >> @@ -733,9 +779,6 @@ static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) >> channel->vbus = NULL; >> } >> >> - platform_set_drvdata(pdev, channel); >> - channel->dev = dev; >> - >> provider = devm_of_phy_provider_register(dev, rcar_gen3_phy_usb2_xlate); >> if (IS_ERR(provider)) { >> dev_err(dev, "Failed to register PHY provider\n"); > > The reset is not asserted in the error path, only in .remove(). > > Oh, Christophe already sent a fix for that... > "[PATCH v3] phy: renesas: rcar-gen3-usb2: Fix an error handling path > in rcar_gen3_phy_usb2_probe()" > https://lore.kernel.org/all/290b25827e3f0742808940719455ff0c5cb9d01d.1726329925.git.christophe.jaillet@wanadoo.fr Yes, I messed this when removing the suspend to RAM from my initial work on this (internal only). Thanks Christophe for handling it. Thank you, Claudiu Beznea > >> @@ -762,6 +805,7 @@ static void rcar_gen3_phy_usb2_remove(struct platform_device *pdev) >> if (channel->is_otg_channel) >> device_remove_file(&pdev->dev, &dev_attr_role); >> >> + reset_control_assert(channel->rstc); >> pm_runtime_disable(&pdev->dev); >> }; > > The rest LGTM. > > Gr{oetje,eeting}s, > > Geert >
diff --git a/drivers/phy/renesas/phy-rcar-gen3-usb2.c b/drivers/phy/renesas/phy-rcar-gen3-usb2.c index 7594f64eb737..cf4299cea579 100644 --- a/drivers/phy/renesas/phy-rcar-gen3-usb2.c +++ b/drivers/phy/renesas/phy-rcar-gen3-usb2.c @@ -19,12 +19,14 @@ #include <linux/platform_device.h> #include <linux/pm_runtime.h> #include <linux/regulator/consumer.h> +#include <linux/reset.h> #include <linux/string.h> #include <linux/usb/of.h> #include <linux/workqueue.h> /******* USB2.0 Host registers (original offset is +0x200) *******/ #define USB2_INT_ENABLE 0x000 +#define USB2_AHB_BUS_CTR 0x008 #define USB2_USBCTR 0x00c #define USB2_SPD_RSM_TIMSET 0x10c #define USB2_OC_TIMSET 0x110 @@ -40,6 +42,10 @@ #define USB2_INT_ENABLE_USBH_INTB_EN BIT(2) /* For EHCI */ #define USB2_INT_ENABLE_USBH_INTA_EN BIT(1) /* For OHCI */ +/* AHB_BUS_CTR */ +#define USB2_AHB_BUS_CTR_MBL_MASK GENMASK(1, 0) +#define USB2_AHB_BUS_CTR_MBL_INCR4 2 + /* USBCTR */ #define USB2_USBCTR_DIRPD BIT(2) #define USB2_USBCTR_PLL_RST BIT(1) @@ -111,6 +117,7 @@ struct rcar_gen3_chan { struct extcon_dev *extcon; struct rcar_gen3_phy rphys[NUM_OF_PHYS]; struct regulator *vbus; + struct reset_control *rstc; struct work_struct work; struct mutex lock; /* protects rphys[...].powered */ enum usb_dr_mode dr_mode; @@ -125,6 +132,7 @@ struct rcar_gen3_chan { struct rcar_gen3_phy_drv_data { const struct phy_ops *phy_usb2_ops; bool no_adp_ctrl; + bool init_bus; }; /* @@ -650,6 +658,35 @@ static enum usb_dr_mode rcar_gen3_get_dr_mode(struct device_node *np) return candidate; } +static int rcar_gen3_phy_usb2_init_bus(struct rcar_gen3_chan *channel) +{ + struct device *dev = channel->dev; + int ret; + u32 val; + + channel->rstc = devm_reset_control_array_get_shared(dev); + if (IS_ERR(channel->rstc)) + return PTR_ERR(channel->rstc); + + ret = pm_runtime_resume_and_get(dev); + if (ret) + return ret; + + ret = reset_control_deassert(channel->rstc); + if (ret) + goto rpm_put; + + val = readl(channel->base + USB2_AHB_BUS_CTR); + val &= ~USB2_AHB_BUS_CTR_MBL_MASK; + val |= USB2_AHB_BUS_CTR_MBL_INCR4; + writel(val, channel->base + USB2_AHB_BUS_CTR); + +rpm_put: + pm_runtime_put(dev); + + return ret; +} + static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) { const struct rcar_gen3_phy_drv_data *phy_data; @@ -703,6 +740,15 @@ static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) goto error; } + platform_set_drvdata(pdev, channel); + channel->dev = dev; + + if (phy_data->init_bus) { + ret = rcar_gen3_phy_usb2_init_bus(channel); + if (ret) + goto error; + } + channel->soc_no_adp_ctrl = phy_data->no_adp_ctrl; if (phy_data->no_adp_ctrl) channel->obint_enable_bits = USB2_OBINT_IDCHG_EN; @@ -733,9 +779,6 @@ static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev) channel->vbus = NULL; } - platform_set_drvdata(pdev, channel); - channel->dev = dev; - provider = devm_of_phy_provider_register(dev, rcar_gen3_phy_usb2_xlate); if (IS_ERR(provider)) { dev_err(dev, "Failed to register PHY provider\n"); @@ -762,6 +805,7 @@ static void rcar_gen3_phy_usb2_remove(struct platform_device *pdev) if (channel->is_otg_channel) device_remove_file(&pdev->dev, &dev_attr_role); + reset_control_assert(channel->rstc); pm_runtime_disable(&pdev->dev); };