[v6,0/4] Introduce Embedded Controller driver for Acer A500

Message

Dmitry Osipenko Nov. 12, 2020, 10:49 p.m. UTC

This series adds support for the Embedded Controller which is found on
Acer Iconia Tab A500 (Android tablet device).

The Embedded Controller is ENE KB930 and it's running firmware customized
for the A500. The firmware interface may be reused by some other sibling
Acer tablets, although none of those tablets are supported in upstream yet.

Changelog:

v6: - Fixed dtschema-checker warning about a wrong indentation, reported
      by kernel bot for v5.

v5: - No changes. Re-sending again in order to check whether dtschema-bot
      warning is resolved now, which didn't happen in v4 because bot used
      older 5.9 kernel code base instead of 5.10.

v4: - No code changes. Added r-b from Rob Herring and Sebastian Reichel.
      Re-sending for 5.11.

    - The v3 of LED driver was applied by Pavel Machek and already presents
      in v5.10 kernel.

v3: - Rebased on a recent linux-next. Fixed new merge conflict and dropped
      "regmap: Use flexible sleep" patch because it's already applied.

v2: - Factored out KB930 device-tree binding into a separate file, like it
      was suggested by Lubomir Rintel.

    - Switched to use regmap API like it was suggested by Lubomir Rintel.

    - Added patch "regmap: Use flexible sleep" which allows not to hog
      CPU while LED is switching state.

    - Corrected MODULE_LICENSE to use "GPL" in all patches.

    - Corrected MFD driver Kconfig entry like it was suggested by
      Lubomir Rintel, it now depends on I2C.

    - Switched to use I2C probe_new() in the MFD driver.

    - Renamed the global pm_off variable, like it was suggested by
      Lubomir Rintel and Lee Jones.

    - Dropped serial number from the battery driver because I realized
      that it's not a battery serial, but a device serial.

    - Battery driver now uses dev_err_probe(), like it was suggested by
      Sebastian Reichel.

    - Dropped legacy LED_ON usage from the LED driver and renamed the
      LEDs, like it was suggested by Pavel Machek. I also checked whether
      LED-name customization via device-tree could be needed by other
      potentially compatible devices and it shouldn't be needed, anyways it
      won't be difficult to extend the code even if I'm wrong.


Dmitry Osipenko (4):
  dt-bindings: mfd: Add ENE KB930 Embedded Controller binding
  mfd: Add driver for Embedded Controller found on Acer Iconia Tab A500
  power: supply: Add battery gauge driver for Acer Iconia Tab A500
  ARM: tegra: acer-a500: Add Embedded Controller

 .../devicetree/bindings/mfd/ene-kb930.yaml    |  65 ++++
 .../boot/dts/tegra20-acer-a500-picasso.dts    |  17 +
 drivers/mfd/Kconfig                           |  12 +
 drivers/mfd/Makefile                          |   1 +
 drivers/mfd/acer-ec-a500.c                    | 203 ++++++++++++
 drivers/power/supply/Kconfig                  |   6 +
 drivers/power/supply/Makefile                 |   1 +
 drivers/power/supply/acer_a500_battery.c      | 297 ++++++++++++++++++
 8 files changed, 602 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/ene-kb930.yaml
 create mode 100644 drivers/mfd/acer-ec-a500.c
 create mode 100644 drivers/power/supply/acer_a500_battery.c