| Message ID | 1421242874-3425-10-git-send-email-l.majewski@samsung.com (mailing list archive) |
|---|---|
| State | Superseded, archived |
| Delegated to: | Eduardo Valentin |
| Headers | show |
On Wed, Jan 14, 2015 at 02:41:07PM +0100, Lukasz Majewski wrote: > Properties necessary for providing Exynos thermal configuration via device > tree. > > Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> > --- > Changes for v3: > - New patch > > --- > .../devicetree/bindings/thermal/exynos-thermal.txt | 17 +++++++++++++++++ > 1 file changed, 17 insertions(+) > > diff --git a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt > index ae738f5..0f44932 100644 > --- a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt > +++ b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt > @@ -39,6 +39,18 @@ > - vtmu-supply: This entry is optional and provides the regulator node supplying > voltage to TMU. If needed this entry can be placed inside > board/platform specific dts file. > +Following properties are mandatory (depending on SoC): > +- samsung,tmu_gain: Gain value for internal TMU operation. > +- samsung,tmu_reference_voltage: Value of TMU IP block's reference voltage > +- samsung,tmu_noise_cancel_mode: Mode for noise cancellation > +- samsung,tmu_efuse_value: Default level of temperature - it is needed when > + in factory fusing produced wrong value > +- samsung,tmu_min_efuse_value: Minimum temperature fused value > +- samsung,tmu_max_efuse_value: Maximum temperature fused value > +- samsung,tmu_first_point_trim: First point trimming value > +- samsung,tmu_second_point_trim: Second point trimming value > +- samsung,tmu_default_temp_offset: Default temperature offset > +- samsung,tmu_cal_type: Callibration type > > Example 1): > > @@ -51,6 +63,7 @@ Example 1): > clock-names = "tmu_apbif"; > status = "disabled"; > vtmu-supply = <&tmu_regulator_node>; > + #include "exynos4412-tmu-sensor-conf.dtsi" > }; > > Example 2): > @@ -61,6 +74,7 @@ Example 2): > interrupts = <0 58 0>; > clocks = <&clock 21>; > clock-names = "tmu_apbif"; > + #include "exynos5440-tmu-sensor-conf.dtsi" Did I miss something or at this point the above file does not exist yet? Please make sure each commit / patch is in a compilable/usable/working state. > }; > > Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") > @@ -70,6 +84,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") > interrupts = <0 184 0>; > clocks = <&clock 318>, <&clock 318>; > clock-names = "tmu_apbif", "tmu_triminfo_apbif"; > + #include "exynos4412-tmu-sensor-conf.dtsi" > }; > > tmu_cpu3: tmu@1006c000 { > @@ -78,6 +93,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") > interrupts = <0 185 0>; > clocks = <&clock 318>, <&clock 319>; > clock-names = "tmu_apbif", "tmu_triminfo_apbif"; > + #include "exynos4412-tmu-sensor-conf.dtsi" > }; > > tmu_gpu: tmu@100a0000 { > @@ -86,6 +102,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") > interrupts = <0 215 0>; > clocks = <&clock 319>, <&clock 318>; > clock-names = "tmu_apbif", "tmu_triminfo_apbif"; > + #include "exynos4412-tmu-sensor-conf.dtsi" > }; > > Note: For multi-instance tmu each instance should have an alias correctly > -- > 2.0.0.rc2 >
On Wed, Jan 14, 2015 at 02:52:25PM -0400, Eduardo Valentin wrote: > On Wed, Jan 14, 2015 at 02:41:07PM +0100, Lukasz Majewski wrote: > > Properties necessary for providing Exynos thermal configuration via device > > tree. > > > > Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> > > --- > > Changes for v3: > > - New patch > > > > --- > > .../devicetree/bindings/thermal/exynos-thermal.txt | 17 +++++++++++++++++ > > 1 file changed, 17 insertions(+) > > > > diff --git a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt > > index ae738f5..0f44932 100644 > > --- a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt > > +++ b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt > > @@ -39,6 +39,18 @@ > > - vtmu-supply: This entry is optional and provides the regulator node supplying > > voltage to TMU. If needed this entry can be placed inside > > board/platform specific dts file. > > +Following properties are mandatory (depending on SoC): > > +- samsung,tmu_gain: Gain value for internal TMU operation. > > +- samsung,tmu_reference_voltage: Value of TMU IP block's reference voltage > > +- samsung,tmu_noise_cancel_mode: Mode for noise cancellation > > +- samsung,tmu_efuse_value: Default level of temperature - it is needed when > > + in factory fusing produced wrong value > > +- samsung,tmu_min_efuse_value: Minimum temperature fused value > > +- samsung,tmu_max_efuse_value: Maximum temperature fused value > > +- samsung,tmu_first_point_trim: First point trimming value > > +- samsung,tmu_second_point_trim: Second point trimming value > > +- samsung,tmu_default_temp_offset: Default temperature offset > > +- samsung,tmu_cal_type: Callibration type > > > > Example 1): > > > > @@ -51,6 +63,7 @@ Example 1): > > clock-names = "tmu_apbif"; > > status = "disabled"; > > vtmu-supply = <&tmu_regulator_node>; > > + #include "exynos4412-tmu-sensor-conf.dtsi" > > }; > > > > Example 2): > > @@ -61,6 +74,7 @@ Example 2): > > interrupts = <0 58 0>; > > clocks = <&clock 21>; > > clock-names = "tmu_apbif"; > > + #include "exynos5440-tmu-sensor-conf.dtsi" > > Did I miss something or at this point the above file does not exist yet? > > Please make sure each commit / patch is in a compilable/usable/working > state. I know this is a Documentation file, but the comment above still applies. > > > }; > > > > Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") > > @@ -70,6 +84,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") > > interrupts = <0 184 0>; > > clocks = <&clock 318>, <&clock 318>; > > clock-names = "tmu_apbif", "tmu_triminfo_apbif"; > > + #include "exynos4412-tmu-sensor-conf.dtsi" > > }; > > > > tmu_cpu3: tmu@1006c000 { > > @@ -78,6 +93,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") > > interrupts = <0 185 0>; > > clocks = <&clock 318>, <&clock 319>; > > clock-names = "tmu_apbif", "tmu_triminfo_apbif"; > > + #include "exynos4412-tmu-sensor-conf.dtsi" > > }; > > > > tmu_gpu: tmu@100a0000 { > > @@ -86,6 +102,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") > > interrupts = <0 215 0>; > > clocks = <&clock 319>, <&clock 318>; > > clock-names = "tmu_apbif", "tmu_triminfo_apbif"; > > + #include "exynos4412-tmu-sensor-conf.dtsi" > > }; > > > > Note: For multi-instance tmu each instance should have an alias correctly > > -- > > 2.0.0.rc2 > >
diff --git a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt index ae738f5..0f44932 100644 --- a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt @@ -39,6 +39,18 @@ - vtmu-supply: This entry is optional and provides the regulator node supplying voltage to TMU. If needed this entry can be placed inside board/platform specific dts file. +Following properties are mandatory (depending on SoC): +- samsung,tmu_gain: Gain value for internal TMU operation. +- samsung,tmu_reference_voltage: Value of TMU IP block's reference voltage +- samsung,tmu_noise_cancel_mode: Mode for noise cancellation +- samsung,tmu_efuse_value: Default level of temperature - it is needed when + in factory fusing produced wrong value +- samsung,tmu_min_efuse_value: Minimum temperature fused value +- samsung,tmu_max_efuse_value: Maximum temperature fused value +- samsung,tmu_first_point_trim: First point trimming value +- samsung,tmu_second_point_trim: Second point trimming value +- samsung,tmu_default_temp_offset: Default temperature offset +- samsung,tmu_cal_type: Callibration type Example 1): @@ -51,6 +63,7 @@ Example 1): clock-names = "tmu_apbif"; status = "disabled"; vtmu-supply = <&tmu_regulator_node>; + #include "exynos4412-tmu-sensor-conf.dtsi" }; Example 2): @@ -61,6 +74,7 @@ Example 2): interrupts = <0 58 0>; clocks = <&clock 21>; clock-names = "tmu_apbif"; + #include "exynos5440-tmu-sensor-conf.dtsi" }; Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") @@ -70,6 +84,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") interrupts = <0 184 0>; clocks = <&clock 318>, <&clock 318>; clock-names = "tmu_apbif", "tmu_triminfo_apbif"; + #include "exynos4412-tmu-sensor-conf.dtsi" }; tmu_cpu3: tmu@1006c000 { @@ -78,6 +93,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") interrupts = <0 185 0>; clocks = <&clock 318>, <&clock 319>; clock-names = "tmu_apbif", "tmu_triminfo_apbif"; + #include "exynos4412-tmu-sensor-conf.dtsi" }; tmu_gpu: tmu@100a0000 { @@ -86,6 +102,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register") interrupts = <0 215 0>; clocks = <&clock 319>, <&clock 318>; clock-names = "tmu_apbif", "tmu_triminfo_apbif"; + #include "exynos4412-tmu-sensor-conf.dtsi" }; Note: For multi-instance tmu each instance should have an alias correctly
Properties necessary for providing Exynos thermal configuration via device tree. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> --- Changes for v3: - New patch --- .../devicetree/bindings/thermal/exynos-thermal.txt | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)