| Message ID | 1534248753-2440-15-git-send-email-sricharan@codeaurora.org (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
| Series | Krait clocks + Krait CPUfreq | expand |
Hi, this email is from Rob's (experimental) review bot. I found a couple of common problems with your patch. Please see below. On Tue, 14 Aug 2018 17:42:33 +0530, Sricharan R wrote: > In Certain QCOM SoCs like ipq8064, apq8064, msm8960, msm8974 > that has KRAIT processors the voltage/current value of each OPP > varies based on the silicon variant in use. > > The required OPP related data is determined based on > the efuse value. This is similar to the existing code for > kryo cores. So adding support for krait cores here. > > Signed-off-by: Sricharan R <sricharan@codeaurora.org> The preferred subject prefix is "dt-bindings: <binding dir>: ...". > --- > .../devicetree/bindings/opp/qcom-nvmem-cpufreq.txt | 3 +- > drivers/cpufreq/Kconfig.arm | 2 +- > drivers/cpufreq/cpufreq-dt-platdev.c | 5 + > drivers/cpufreq/qcom-cpufreq-nvmem.c | 151 +++++++++++++++++++-- > 4 files changed, 149 insertions(+), 12 deletions(-) > DT bindings (including binding headers) should be a separate patch. See Documentation/devicetree/bindings/submitting-patches.txt.
On Tue, Aug 14, 2018 at 05:42:33PM +0530, Sricharan R wrote: > In Certain QCOM SoCs like ipq8064, apq8064, msm8960, msm8974 > that has KRAIT processors the voltage/current value of each OPP > varies based on the silicon variant in use. > > The required OPP related data is determined based on > the efuse value. This is similar to the existing code for > kryo cores. So adding support for krait cores here. > > Signed-off-by: Sricharan R <sricharan@codeaurora.org> > --- > .../devicetree/bindings/opp/qcom-nvmem-cpufreq.txt | 3 +- > drivers/cpufreq/Kconfig.arm | 2 +- > drivers/cpufreq/cpufreq-dt-platdev.c | 5 + > drivers/cpufreq/qcom-cpufreq-nvmem.c | 151 +++++++++++++++++++-- > 4 files changed, 149 insertions(+), 12 deletions(-) > > diff --git a/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt b/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt > index 6dcdfcd..7bc0f1a 100644 > --- a/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt > +++ b/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt > @@ -19,7 +19,8 @@ In 'cpus' nodes: > > In 'operating-points-v2' table: > - compatible: Should be > - - 'operating-points-v2-qcom-cpu' for apq8096 and msm8996. > + - 'operating-points-v2-qcom-cpu' for apq8096, msm8996, msm8974, > + apq8064, msm8960 and ipq8074. > - nvmem-cells: A phandle pointing to a nvmem-cells node representing the > efuse registers that has information about the > speedbin that is used to select the right frequency/voltage Hello Sricharan, I see several references to kryo in this file that should probably be removed or renamed. Also, the documentation for opp-supported-hw lists how the different bitmap values maps to the different compatible HW. It might be good to add a note that the table is only for msm8996, and for orther SoCs, there is a 1:1 speedbin to opp-supported-hw mapping. Kind regards, Niklas > diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm > index 13fbd97..497ae89 100644 > --- a/drivers/cpufreq/Kconfig.arm > +++ b/drivers/cpufreq/Kconfig.arm > @@ -126,7 +126,7 @@ config ARM_OMAP2PLUS_CPUFREQ > > config ARM_QCOM_CPUFREQ_NVMEM > tristate "Qualcomm nvmem based CPUFreq" > - depends on ARM64 > + depends on ARCH_QCOM > depends on QCOM_QFPROM > depends on QCOM_SMEM > select PM_OPP > diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c > index fe14c57..917cdc2 100644 > --- a/drivers/cpufreq/cpufreq-dt-platdev.c > +++ b/drivers/cpufreq/cpufreq-dt-platdev.c > @@ -128,6 +128,11 @@ > { .compatible = "ti,am43", }, > { .compatible = "ti,dra7", }, > > + { .compatible = "qcom,ipq8064", }, > + { .compatible = "qcom,apq8064", }, > + { .compatible = "qcom,msm8974", }, > + { .compatible = "qcom,msm8960", }, > + > { } > }; > > diff --git a/drivers/cpufreq/qcom-cpufreq-nvmem.c b/drivers/cpufreq/qcom-cpufreq-nvmem.c > index 0ad8e5b..5f2add0 100644 > --- a/drivers/cpufreq/qcom-cpufreq-nvmem.c > +++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c > @@ -45,6 +45,82 @@ enum _msm8996_version { > > static struct platform_device *cpufreq_dt_pdev, *cpufreq_pdev; > > +static void __init get_krait_bin_format_a(int *speed, int *pvs, int *pvs_ver, > + struct nvmem_cell *pvs_nvmem, u8 *buf) > +{ > + u32 pte_efuse; > + > + pte_efuse = *((u32 *)buf); > + > + *speed = pte_efuse & 0xf; > + if (*speed == 0xf) > + *speed = (pte_efuse >> 4) & 0xf; > + > + if (*speed == 0xf) { > + *speed = 0; > + pr_warn("Speed bin: Defaulting to %d\n", *speed); > + } else { > + pr_info("Speed bin: %d\n", *speed); > + } > + > + *pvs = (pte_efuse >> 10) & 0x7; > + if (*pvs == 0x7) > + *pvs = (pte_efuse >> 13) & 0x7; > + > + if (*pvs == 0x7) { > + *pvs = 0; > + pr_warn("PVS bin: Defaulting to %d\n", *pvs); > + } else { > + pr_info("PVS bin: %d\n", *pvs); > + } > + > + kfree(buf); > +} > + > +static void __init get_krait_bin_format_b(int *speed, int *pvs, int *pvs_ver, > + struct nvmem_cell *pvs_nvmem, u8 *buf) > +{ > + u32 pte_efuse, redundant_sel; > + > + pte_efuse = *((u32 *)buf); > + redundant_sel = (pte_efuse >> 24) & 0x7; > + *speed = pte_efuse & 0x7; > + > + /* 4 bits of PVS are in efuse register bits 31, 8-6. */ > + *pvs = ((pte_efuse >> 28) & 0x8) | ((pte_efuse >> 6) & 0x7); > + *pvs_ver = (pte_efuse >> 4) & 0x3; > + > + switch (redundant_sel) { > + case 1: > + *speed = (pte_efuse >> 27) & 0xf; > + break; > + case 2: > + *pvs = (pte_efuse >> 27) & 0xf; > + break; > + } > + > + /* Check SPEED_BIN_BLOW_STATUS */ > + if (pte_efuse & BIT(3)) { > + pr_info("Speed bin: %d\n", *speed); > + } else { > + pr_warn("Speed bin not set. Defaulting to 0!\n"); > + *speed = 0; > + } > + > + /* Check PVS_BLOW_STATUS */ > + pte_efuse = *(((u32 *)buf) + 4); > + pte_efuse &= BIT(21); > + if (pte_efuse) { > + pr_info("PVS bin: %d\n", *pvs); > + } else { > + pr_warn("PVS bin not set. Defaulting to 0!\n"); > + *pvs = 0; > + } > + > + pr_info("PVS version: %d\n", *pvs_ver); > + kfree(buf); > +} > + > static enum _msm8996_version __init qcom_cpufreq_get_msm_id(void) > { > size_t len; > @@ -74,6 +150,35 @@ static enum _msm8996_version __init qcom_cpufreq_get_msm_id(void) > return version; > } > > +static int qcom_cpufreq_krait_name_version(struct device *cpu_dev, > + struct nvmem_cell *speedbin_nvmem, > + char **name, > + u32 *versions) > +{ > + int speed = 0, pvs = 0, pvs_ver = 0; > + u8 *buf; > + size_t len; > + > + buf = nvmem_cell_read(speedbin_nvmem, &len); > + if (len == 4) { > + get_krait_bin_format_a(&speed, &pvs, &pvs_ver, > + speedbin_nvmem, buf); > + } else if (len == 8) { > + get_krait_bin_format_b(&speed, &pvs, &pvs_ver, > + speedbin_nvmem, buf); > + } else { > + dev_err(cpu_dev, "Unable to read nvmem data. Defaulting to 0!\n"); > + return -ENODEV; > + } > + > + snprintf(*name, sizeof("speedXX-pvsXX-vXX"), "speed%d-pvs%d-v%d", > + speed, pvs, pvs_ver); > + > + *versions = (1 << speed); > + > + return 0; > +} > + > static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev, > struct nvmem_cell *speedbin_nvmem, > char **pvs_name, > @@ -83,6 +188,7 @@ static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev, > u8 *speedbin; > enum _msm8996_version msm8996_version; > > + *pvs_name = NULL; > msm8996_version = qcom_cpufreq_get_msm_id(); > if (NUM_OF_MSM8996_VERSIONS == msm8996_version) { > dev_err(cpu_dev, "Not Snapdragon 820/821!"); > @@ -111,7 +217,7 @@ static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev, > > static int qcom_cpufreq_probe(struct platform_device *pdev) > { > - struct opp_table *opp_tables[NR_CPUS] = { NULL }; > + struct opp_table *tbl1[NR_CPUS] = { NULL }, *tbl2[NR_CPUS] = { NULL }; > int (*get_version)(struct device *cpu_dev, > struct nvmem_cell *speedbin_nvmem, > char **name, int *versions); > @@ -120,8 +226,8 @@ static int qcom_cpufreq_probe(struct platform_device *pdev) > struct device *cpu_dev; > unsigned cpu; > u32 versions; > - char *pvs_name = NULL; > const struct of_device_id *match; > + char *pvs_name = "speedXX-pvsXX-vXX"; > int ret; > > cpu_dev = get_cpu_device(0); > @@ -163,10 +269,19 @@ static int qcom_cpufreq_probe(struct platform_device *pdev) > goto free_opp; > } > > - opp_tables[cpu] = dev_pm_opp_set_supported_hw(cpu_dev, > - &versions, 1); > - if (IS_ERR(opp_tables[cpu])) { > - ret = PTR_ERR(opp_tables[cpu]); > + if (pvs_name) { > + tbl1[cpu] = dev_pm_opp_set_prop_name(cpu_dev, pvs_name); > + if (IS_ERR(tbl1[cpu])) { > + ret = PTR_ERR(tbl1[cpu]); > + dev_err(cpu_dev, "Failed to add OPP name %s\n", > + pvs_name); > + goto free_opp; > + } > + } > + > + tbl2[cpu] = dev_pm_opp_set_supported_hw(cpu_dev, &versions, 1); > + if (IS_ERR(tbl2[cpu])) { > + ret = PTR_ERR(tbl2[cpu]); > dev_err(cpu_dev, "Failed to set supported hardware\n"); > goto free_opp; > } > @@ -182,9 +297,15 @@ static int qcom_cpufreq_probe(struct platform_device *pdev) > > free_opp: > for_each_possible_cpu(cpu) { > - if (IS_ERR_OR_NULL(opp_tables[cpu])) > + if (IS_ERR_OR_NULL(tbl1[cpu])) > + break; > + dev_pm_opp_put_prop_name(tbl1[cpu]); > + } > + > + for_each_possible_cpu(cpu) { > + if (IS_ERR_OR_NULL(tbl2[cpu])) > break; > - dev_pm_opp_put_supported_hw(opp_tables[cpu]); > + dev_pm_opp_put_supported_hw(tbl2[cpu]); > } > > return ret; > @@ -205,8 +326,18 @@ static int qcom_cpufreq_remove(struct platform_device *pdev) > }; > > static const struct of_device_id qcom_cpufreq_match_list[] __initconst = { > - { .compatible = "qcom,apq8096", .data = qcom_cpufreq_kryo_name_version}, > - { .compatible = "qcom,msm8996", .data = qcom_cpufreq_kryo_name_version}, > + { .compatible = "qcom,apq8096", > + .data = qcom_cpufreq_kryo_name_version}, > + { .compatible = "qcom,msm8996", > + .data = qcom_cpufreq_kryo_name_version}, > + { .compatible = "qcom,ipq8064", > + .data = qcom_cpufreq_krait_name_version }, > + { .compatible = "qcom,apq8064", > + .data = qcom_cpufreq_krait_name_version }, > + { .compatible = "qcom,msm8974", > + .data = qcom_cpufreq_krait_name_version }, > + { .compatible = "qcom,msm8960", > + .data = qcom_cpufreq_krait_name_version }, > {}, > }; > > -- > QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation >
On Tue, Aug 14, 2018 at 05:42:33PM +0530, Sricharan R wrote: > In Certain QCOM SoCs like ipq8064, apq8064, msm8960, msm8974 > that has KRAIT processors the voltage/current value of each OPP > varies based on the silicon variant in use. > > The required OPP related data is determined based on > the efuse value. This is similar to the existing code for > kryo cores. So adding support for krait cores here. > > Signed-off-by: Sricharan R <sricharan@codeaurora.org> > --- > .../devicetree/bindings/opp/qcom-nvmem-cpufreq.txt | 3 +- > drivers/cpufreq/Kconfig.arm | 2 +- > drivers/cpufreq/cpufreq-dt-platdev.c | 5 + > drivers/cpufreq/qcom-cpufreq-nvmem.c | 151 +++++++++++++++++++-- > 4 files changed, 149 insertions(+), 12 deletions(-) > > diff --git a/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt b/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt > index 6dcdfcd..7bc0f1a 100644 > --- a/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt > +++ b/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt > @@ -19,7 +19,8 @@ In 'cpus' nodes: > > In 'operating-points-v2' table: > - compatible: Should be > - - 'operating-points-v2-qcom-cpu' for apq8096 and msm8996. > + - 'operating-points-v2-qcom-cpu' for apq8096, msm8996, msm8974, > + apq8064, msm8960 and ipq8074. > - nvmem-cells: A phandle pointing to a nvmem-cells node representing the > efuse registers that has information about the > speedbin that is used to select the right frequency/voltage > diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm > index 13fbd97..497ae89 100644 > --- a/drivers/cpufreq/Kconfig.arm > +++ b/drivers/cpufreq/Kconfig.arm > @@ -126,7 +126,7 @@ config ARM_OMAP2PLUS_CPUFREQ > > config ARM_QCOM_CPUFREQ_NVMEM > tristate "Qualcomm nvmem based CPUFreq" > - depends on ARM64 > + depends on ARCH_QCOM > depends on QCOM_QFPROM > depends on QCOM_SMEM > select PM_OPP > diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c > index fe14c57..917cdc2 100644 > --- a/drivers/cpufreq/cpufreq-dt-platdev.c > +++ b/drivers/cpufreq/cpufreq-dt-platdev.c > @@ -128,6 +128,11 @@ > { .compatible = "ti,am43", }, > { .compatible = "ti,dra7", }, > > + { .compatible = "qcom,ipq8064", }, > + { .compatible = "qcom,apq8064", }, > + { .compatible = "qcom,msm8974", }, > + { .compatible = "qcom,msm8960", }, > + > { } > }; > > diff --git a/drivers/cpufreq/qcom-cpufreq-nvmem.c b/drivers/cpufreq/qcom-cpufreq-nvmem.c > index 0ad8e5b..5f2add0 100644 > --- a/drivers/cpufreq/qcom-cpufreq-nvmem.c > +++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c > @@ -45,6 +45,82 @@ enum _msm8996_version { > > static struct platform_device *cpufreq_dt_pdev, *cpufreq_pdev; > > +static void __init get_krait_bin_format_a(int *speed, int *pvs, int *pvs_ver, > + struct nvmem_cell *pvs_nvmem, u8 *buf) Hello Sricharan, pvs_nvmem seems to be unused both here and in get_krait_bin_format_b(). Kind regards, Niklas > +{ > + u32 pte_efuse; > + > + pte_efuse = *((u32 *)buf); > + > + *speed = pte_efuse & 0xf; > + if (*speed == 0xf) > + *speed = (pte_efuse >> 4) & 0xf; > + > + if (*speed == 0xf) { > + *speed = 0; > + pr_warn("Speed bin: Defaulting to %d\n", *speed); > + } else { > + pr_info("Speed bin: %d\n", *speed); > + } > + > + *pvs = (pte_efuse >> 10) & 0x7; > + if (*pvs == 0x7) > + *pvs = (pte_efuse >> 13) & 0x7; > + > + if (*pvs == 0x7) { > + *pvs = 0; > + pr_warn("PVS bin: Defaulting to %d\n", *pvs); > + } else { > + pr_info("PVS bin: %d\n", *pvs); > + } > + > + kfree(buf); > +} > + > +static void __init get_krait_bin_format_b(int *speed, int *pvs, int *pvs_ver, > + struct nvmem_cell *pvs_nvmem, u8 *buf) > +{ > + u32 pte_efuse, redundant_sel; > + > + pte_efuse = *((u32 *)buf); > + redundant_sel = (pte_efuse >> 24) & 0x7; > + *speed = pte_efuse & 0x7; > + > + /* 4 bits of PVS are in efuse register bits 31, 8-6. */ > + *pvs = ((pte_efuse >> 28) & 0x8) | ((pte_efuse >> 6) & 0x7); > + *pvs_ver = (pte_efuse >> 4) & 0x3; > + > + switch (redundant_sel) { > + case 1: > + *speed = (pte_efuse >> 27) & 0xf; > + break; > + case 2: > + *pvs = (pte_efuse >> 27) & 0xf; > + break; > + } > + > + /* Check SPEED_BIN_BLOW_STATUS */ > + if (pte_efuse & BIT(3)) { > + pr_info("Speed bin: %d\n", *speed); > + } else { > + pr_warn("Speed bin not set. Defaulting to 0!\n"); > + *speed = 0; > + } > + > + /* Check PVS_BLOW_STATUS */ > + pte_efuse = *(((u32 *)buf) + 4); > + pte_efuse &= BIT(21); > + if (pte_efuse) { > + pr_info("PVS bin: %d\n", *pvs); > + } else { > + pr_warn("PVS bin not set. Defaulting to 0!\n"); > + *pvs = 0; > + } > + > + pr_info("PVS version: %d\n", *pvs_ver); > + kfree(buf); > +} > + > static enum _msm8996_version __init qcom_cpufreq_get_msm_id(void) > { > size_t len; > @@ -74,6 +150,35 @@ static enum _msm8996_version __init qcom_cpufreq_get_msm_id(void) > return version; > } > > +static int qcom_cpufreq_krait_name_version(struct device *cpu_dev, > + struct nvmem_cell *speedbin_nvmem, > + char **name, > + u32 *versions) > +{ > + int speed = 0, pvs = 0, pvs_ver = 0; > + u8 *buf; > + size_t len; > + > + buf = nvmem_cell_read(speedbin_nvmem, &len); > + if (len == 4) { > + get_krait_bin_format_a(&speed, &pvs, &pvs_ver, > + speedbin_nvmem, buf); > + } else if (len == 8) { > + get_krait_bin_format_b(&speed, &pvs, &pvs_ver, > + speedbin_nvmem, buf); > + } else { > + dev_err(cpu_dev, "Unable to read nvmem data. Defaulting to 0!\n"); > + return -ENODEV; > + } > + > + snprintf(*name, sizeof("speedXX-pvsXX-vXX"), "speed%d-pvs%d-v%d", > + speed, pvs, pvs_ver); > + > + *versions = (1 << speed); > + > + return 0; > +} > + > static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev, > struct nvmem_cell *speedbin_nvmem, > char **pvs_name, > @@ -83,6 +188,7 @@ static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev, > u8 *speedbin; > enum _msm8996_version msm8996_version; > > + *pvs_name = NULL; > msm8996_version = qcom_cpufreq_get_msm_id(); > if (NUM_OF_MSM8996_VERSIONS == msm8996_version) { > dev_err(cpu_dev, "Not Snapdragon 820/821!"); > @@ -111,7 +217,7 @@ static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev, > > static int qcom_cpufreq_probe(struct platform_device *pdev) > { > - struct opp_table *opp_tables[NR_CPUS] = { NULL }; > + struct opp_table *tbl1[NR_CPUS] = { NULL }, *tbl2[NR_CPUS] = { NULL }; > int (*get_version)(struct device *cpu_dev, > struct nvmem_cell *speedbin_nvmem, > char **name, int *versions); > @@ -120,8 +226,8 @@ static int qcom_cpufreq_probe(struct platform_device *pdev) > struct device *cpu_dev; > unsigned cpu; > u32 versions; > - char *pvs_name = NULL; > const struct of_device_id *match; > + char *pvs_name = "speedXX-pvsXX-vXX"; > int ret; > > cpu_dev = get_cpu_device(0); > @@ -163,10 +269,19 @@ static int qcom_cpufreq_probe(struct platform_device *pdev) > goto free_opp; > } > > - opp_tables[cpu] = dev_pm_opp_set_supported_hw(cpu_dev, > - &versions, 1); > - if (IS_ERR(opp_tables[cpu])) { > - ret = PTR_ERR(opp_tables[cpu]); > + if (pvs_name) { > + tbl1[cpu] = dev_pm_opp_set_prop_name(cpu_dev, pvs_name); > + if (IS_ERR(tbl1[cpu])) { > + ret = PTR_ERR(tbl1[cpu]); > + dev_err(cpu_dev, "Failed to add OPP name %s\n", > + pvs_name); > + goto free_opp; > + } > + } > + > + tbl2[cpu] = dev_pm_opp_set_supported_hw(cpu_dev, &versions, 1); > + if (IS_ERR(tbl2[cpu])) { > + ret = PTR_ERR(tbl2[cpu]); > dev_err(cpu_dev, "Failed to set supported hardware\n"); > goto free_opp; > } > @@ -182,9 +297,15 @@ static int qcom_cpufreq_probe(struct platform_device *pdev) > > free_opp: > for_each_possible_cpu(cpu) { > - if (IS_ERR_OR_NULL(opp_tables[cpu])) > + if (IS_ERR_OR_NULL(tbl1[cpu])) > + break; > + dev_pm_opp_put_prop_name(tbl1[cpu]); > + } > + > + for_each_possible_cpu(cpu) { > + if (IS_ERR_OR_NULL(tbl2[cpu])) > break; > - dev_pm_opp_put_supported_hw(opp_tables[cpu]); > + dev_pm_opp_put_supported_hw(tbl2[cpu]); > } > > return ret; > @@ -205,8 +326,18 @@ static int qcom_cpufreq_remove(struct platform_device *pdev) > }; > > static const struct of_device_id qcom_cpufreq_match_list[] __initconst = { > - { .compatible = "qcom,apq8096", .data = qcom_cpufreq_kryo_name_version}, > - { .compatible = "qcom,msm8996", .data = qcom_cpufreq_kryo_name_version}, > + { .compatible = "qcom,apq8096", > + .data = qcom_cpufreq_kryo_name_version}, > + { .compatible = "qcom,msm8996", > + .data = qcom_cpufreq_kryo_name_version}, > + { .compatible = "qcom,ipq8064", > + .data = qcom_cpufreq_krait_name_version }, > + { .compatible = "qcom,apq8064", > + .data = qcom_cpufreq_krait_name_version }, > + { .compatible = "qcom,msm8974", > + .data = qcom_cpufreq_krait_name_version }, > + { .compatible = "qcom,msm8960", > + .data = qcom_cpufreq_krait_name_version }, > {}, > }; > > -- > QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation >
diff --git a/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt b/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt index 6dcdfcd..7bc0f1a 100644 --- a/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt +++ b/Documentation/devicetree/bindings/opp/qcom-nvmem-cpufreq.txt @@ -19,7 +19,8 @@ In 'cpus' nodes: In 'operating-points-v2' table: - compatible: Should be - - 'operating-points-v2-qcom-cpu' for apq8096 and msm8996. + - 'operating-points-v2-qcom-cpu' for apq8096, msm8996, msm8974, + apq8064, msm8960 and ipq8074. - nvmem-cells: A phandle pointing to a nvmem-cells node representing the efuse registers that has information about the speedbin that is used to select the right frequency/voltage diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm index 13fbd97..497ae89 100644 --- a/drivers/cpufreq/Kconfig.arm +++ b/drivers/cpufreq/Kconfig.arm @@ -126,7 +126,7 @@ config ARM_OMAP2PLUS_CPUFREQ config ARM_QCOM_CPUFREQ_NVMEM tristate "Qualcomm nvmem based CPUFreq" - depends on ARM64 + depends on ARCH_QCOM depends on QCOM_QFPROM depends on QCOM_SMEM select PM_OPP diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c index fe14c57..917cdc2 100644 --- a/drivers/cpufreq/cpufreq-dt-platdev.c +++ b/drivers/cpufreq/cpufreq-dt-platdev.c @@ -128,6 +128,11 @@ { .compatible = "ti,am43", }, { .compatible = "ti,dra7", }, + { .compatible = "qcom,ipq8064", }, + { .compatible = "qcom,apq8064", }, + { .compatible = "qcom,msm8974", }, + { .compatible = "qcom,msm8960", }, + { } }; diff --git a/drivers/cpufreq/qcom-cpufreq-nvmem.c b/drivers/cpufreq/qcom-cpufreq-nvmem.c index 0ad8e5b..5f2add0 100644 --- a/drivers/cpufreq/qcom-cpufreq-nvmem.c +++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c @@ -45,6 +45,82 @@ enum _msm8996_version { static struct platform_device *cpufreq_dt_pdev, *cpufreq_pdev; +static void __init get_krait_bin_format_a(int *speed, int *pvs, int *pvs_ver, + struct nvmem_cell *pvs_nvmem, u8 *buf) +{ + u32 pte_efuse; + + pte_efuse = *((u32 *)buf); + + *speed = pte_efuse & 0xf; + if (*speed == 0xf) + *speed = (pte_efuse >> 4) & 0xf; + + if (*speed == 0xf) { + *speed = 0; + pr_warn("Speed bin: Defaulting to %d\n", *speed); + } else { + pr_info("Speed bin: %d\n", *speed); + } + + *pvs = (pte_efuse >> 10) & 0x7; + if (*pvs == 0x7) + *pvs = (pte_efuse >> 13) & 0x7; + + if (*pvs == 0x7) { + *pvs = 0; + pr_warn("PVS bin: Defaulting to %d\n", *pvs); + } else { + pr_info("PVS bin: %d\n", *pvs); + } + + kfree(buf); +} + +static void __init get_krait_bin_format_b(int *speed, int *pvs, int *pvs_ver, + struct nvmem_cell *pvs_nvmem, u8 *buf) +{ + u32 pte_efuse, redundant_sel; + + pte_efuse = *((u32 *)buf); + redundant_sel = (pte_efuse >> 24) & 0x7; + *speed = pte_efuse & 0x7; + + /* 4 bits of PVS are in efuse register bits 31, 8-6. */ + *pvs = ((pte_efuse >> 28) & 0x8) | ((pte_efuse >> 6) & 0x7); + *pvs_ver = (pte_efuse >> 4) & 0x3; + + switch (redundant_sel) { + case 1: + *speed = (pte_efuse >> 27) & 0xf; + break; + case 2: + *pvs = (pte_efuse >> 27) & 0xf; + break; + } + + /* Check SPEED_BIN_BLOW_STATUS */ + if (pte_efuse & BIT(3)) { + pr_info("Speed bin: %d\n", *speed); + } else { + pr_warn("Speed bin not set. Defaulting to 0!\n"); + *speed = 0; + } + + /* Check PVS_BLOW_STATUS */ + pte_efuse = *(((u32 *)buf) + 4); + pte_efuse &= BIT(21); + if (pte_efuse) { + pr_info("PVS bin: %d\n", *pvs); + } else { + pr_warn("PVS bin not set. Defaulting to 0!\n"); + *pvs = 0; + } + + pr_info("PVS version: %d\n", *pvs_ver); + kfree(buf); +} + static enum _msm8996_version __init qcom_cpufreq_get_msm_id(void) { size_t len; @@ -74,6 +150,35 @@ static enum _msm8996_version __init qcom_cpufreq_get_msm_id(void) return version; } +static int qcom_cpufreq_krait_name_version(struct device *cpu_dev, + struct nvmem_cell *speedbin_nvmem, + char **name, + u32 *versions) +{ + int speed = 0, pvs = 0, pvs_ver = 0; + u8 *buf; + size_t len; + + buf = nvmem_cell_read(speedbin_nvmem, &len); + if (len == 4) { + get_krait_bin_format_a(&speed, &pvs, &pvs_ver, + speedbin_nvmem, buf); + } else if (len == 8) { + get_krait_bin_format_b(&speed, &pvs, &pvs_ver, + speedbin_nvmem, buf); + } else { + dev_err(cpu_dev, "Unable to read nvmem data. Defaulting to 0!\n"); + return -ENODEV; + } + + snprintf(*name, sizeof("speedXX-pvsXX-vXX"), "speed%d-pvs%d-v%d", + speed, pvs, pvs_ver); + + *versions = (1 << speed); + + return 0; +} + static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev, struct nvmem_cell *speedbin_nvmem, char **pvs_name, @@ -83,6 +188,7 @@ static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev, u8 *speedbin; enum _msm8996_version msm8996_version; + *pvs_name = NULL; msm8996_version = qcom_cpufreq_get_msm_id(); if (NUM_OF_MSM8996_VERSIONS == msm8996_version) { dev_err(cpu_dev, "Not Snapdragon 820/821!"); @@ -111,7 +217,7 @@ static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev, static int qcom_cpufreq_probe(struct platform_device *pdev) { - struct opp_table *opp_tables[NR_CPUS] = { NULL }; + struct opp_table *tbl1[NR_CPUS] = { NULL }, *tbl2[NR_CPUS] = { NULL }; int (*get_version)(struct device *cpu_dev, struct nvmem_cell *speedbin_nvmem, char **name, int *versions); @@ -120,8 +226,8 @@ static int qcom_cpufreq_probe(struct platform_device *pdev) struct device *cpu_dev; unsigned cpu; u32 versions; - char *pvs_name = NULL; const struct of_device_id *match; + char *pvs_name = "speedXX-pvsXX-vXX"; int ret; cpu_dev = get_cpu_device(0); @@ -163,10 +269,19 @@ static int qcom_cpufreq_probe(struct platform_device *pdev) goto free_opp; } - opp_tables[cpu] = dev_pm_opp_set_supported_hw(cpu_dev, - &versions, 1); - if (IS_ERR(opp_tables[cpu])) { - ret = PTR_ERR(opp_tables[cpu]); + if (pvs_name) { + tbl1[cpu] = dev_pm_opp_set_prop_name(cpu_dev, pvs_name); + if (IS_ERR(tbl1[cpu])) { + ret = PTR_ERR(tbl1[cpu]); + dev_err(cpu_dev, "Failed to add OPP name %s\n", + pvs_name); + goto free_opp; + } + } + + tbl2[cpu] = dev_pm_opp_set_supported_hw(cpu_dev, &versions, 1); + if (IS_ERR(tbl2[cpu])) { + ret = PTR_ERR(tbl2[cpu]); dev_err(cpu_dev, "Failed to set supported hardware\n"); goto free_opp; } @@ -182,9 +297,15 @@ static int qcom_cpufreq_probe(struct platform_device *pdev) free_opp: for_each_possible_cpu(cpu) { - if (IS_ERR_OR_NULL(opp_tables[cpu])) + if (IS_ERR_OR_NULL(tbl1[cpu])) + break; + dev_pm_opp_put_prop_name(tbl1[cpu]); + } + + for_each_possible_cpu(cpu) { + if (IS_ERR_OR_NULL(tbl2[cpu])) break; - dev_pm_opp_put_supported_hw(opp_tables[cpu]); + dev_pm_opp_put_supported_hw(tbl2[cpu]); } return ret; @@ -205,8 +326,18 @@ static int qcom_cpufreq_remove(struct platform_device *pdev) }; static const struct of_device_id qcom_cpufreq_match_list[] __initconst = { - { .compatible = "qcom,apq8096", .data = qcom_cpufreq_kryo_name_version}, - { .compatible = "qcom,msm8996", .data = qcom_cpufreq_kryo_name_version}, + { .compatible = "qcom,apq8096", + .data = qcom_cpufreq_kryo_name_version}, + { .compatible = "qcom,msm8996", + .data = qcom_cpufreq_kryo_name_version}, + { .compatible = "qcom,ipq8064", + .data = qcom_cpufreq_krait_name_version }, + { .compatible = "qcom,apq8064", + .data = qcom_cpufreq_krait_name_version }, + { .compatible = "qcom,msm8974", + .data = qcom_cpufreq_krait_name_version }, + { .compatible = "qcom,msm8960", + .data = qcom_cpufreq_krait_name_version }, {}, };
In Certain QCOM SoCs like ipq8064, apq8064, msm8960, msm8974 that has KRAIT processors the voltage/current value of each OPP varies based on the silicon variant in use. The required OPP related data is determined based on the efuse value. This is similar to the existing code for kryo cores. So adding support for krait cores here. Signed-off-by: Sricharan R <sricharan@codeaurora.org> --- .../devicetree/bindings/opp/qcom-nvmem-cpufreq.txt | 3 +- drivers/cpufreq/Kconfig.arm | 2 +- drivers/cpufreq/cpufreq-dt-platdev.c | 5 + drivers/cpufreq/qcom-cpufreq-nvmem.c | 151 +++++++++++++++++++-- 4 files changed, 149 insertions(+), 12 deletions(-)