@@ -1,4 +1,12 @@
# SPDX-License-Identifier: GPL-2.0-only
+config BCM2711_THERMAL
+ tristate "Broadcom AVS RO thermal sensor driver"
+ depends on ARCH_BCM2835 || COMPILE_TEST
+ depends on HAS_IOMEM
+ depends on THERMAL_OF
+ help
+ Support for thermal sensors on Broadcom BCM2711 SoCs.
+
config BCM2835_THERMAL
tristate "Thermal sensors on bcm2835 SoC"
depends on ARCH_BCM2835 || COMPILE_TEST
@@ -1,4 +1,5 @@
# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_BCM2711_THERMAL) += bcm2711_thermal.o
obj-$(CONFIG_BCM2835_THERMAL) += bcm2835_thermal.o
obj-$(CONFIG_BRCMSTB_THERMAL) += brcmstb_thermal.o
obj-$(CONFIG_BCM_NS_THERMAL) += ns-thermal.o
new file mode 100644
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Broadcom AVS RO thermal sensor driver
+ *
+ * based on brcmstb_thermal
+ *
+ * Copyright (C) 2019 Stefan Wahren
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of_device.h>
+#include <linux/thermal.h>
+
+#include "../thermal_hwmon.h"
+
+#define AVS_RO_TEMP_STATUS 0x00
+ #define AVS_RO_TEMP_STATUS_valid_msk (BIT(16) | BIT(10))
+ #define AVS_RO_TEMP_STATUS_data_msk GENMASK(9, 0)
+
+struct bcm2711_thermal_priv {
+ void __iomem *base;
+ struct device *dev;
+ struct clk *clk;
+ struct thermal_zone_device *thermal;
+};
+
+static int bcm2711_get_temp(void *data, int *temp)
+{
+ struct bcm2711_thermal_priv *priv = data;
+ int slope = thermal_zone_get_slope(priv->thermal);
+ int offset = thermal_zone_get_offset(priv->thermal);
+ u32 val;
+ long t;
+
+ val = __raw_readl(priv->base + AVS_RO_TEMP_STATUS);
+
+ if (!(val & AVS_RO_TEMP_STATUS_valid_msk)) {
+ dev_err(priv->dev, "reading not valid\n");
+ return -EIO;
+ }
+
+ val &= AVS_RO_TEMP_STATUS_data_msk;
+
+ /* Convert a HW code to a temperature reading (millidegree celsius) */
+ t = slope * val + offset;
+ if (t < 0)
+ *temp = 0;
+ else
+ *temp = t;
+
+ return 0;
+}
+
+static const struct thermal_zone_of_device_ops bcm2711_thermal_of_ops = {
+ .get_temp = bcm2711_get_temp,
+};
+
+static const struct of_device_id bcm2711_thermal_id_table[] = {
+ { .compatible = "brcm,bcm2711-thermal" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, bcm2711_thermal_id_table);
+
+static int bcm2711_thermal_probe(struct platform_device *pdev)
+{
+ struct thermal_zone_device *thermal;
+ struct bcm2711_thermal_priv *priv;
+ struct resource *res;
+ int ret;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ priv->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(priv->base))
+ return PTR_ERR(priv->base);
+
+ priv->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(priv->clk)) {
+ ret = PTR_ERR(priv->clk);
+ if (ret != -EPROBE_DEFER)
+ dev_err(&pdev->dev, "could not get clk: %d\n", ret);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(priv->clk);
+ if (ret)
+ return ret;
+
+ priv->dev = &pdev->dev;
+ platform_set_drvdata(pdev, priv);
+
+ thermal = devm_thermal_zone_of_sensor_register(&pdev->dev, 0, priv,
+ &bcm2711_thermal_of_ops);
+ if (IS_ERR(thermal)) {
+ ret = PTR_ERR(thermal);
+ dev_err(&pdev->dev, "could not register sensor: %d\n", ret);
+ goto err_clk;
+ }
+
+ priv->thermal = thermal;
+
+ thermal->tzp->no_hwmon = false;
+ ret = thermal_add_hwmon_sysfs(thermal);
+ if (ret)
+ return ret;
+
+ return 0;
+
+err_clk:
+ clk_disable_unprepare(priv->clk);
+
+ return ret;
+}
+
+static int bcm2711_thermal_remove(struct platform_device *pdev)
+{
+ struct bcm2711_thermal_priv *priv = platform_get_drvdata(pdev);
+
+ clk_disable_unprepare(priv->clk);
+
+ return 0;
+}
+
+static struct platform_driver bcm2711_thermal_driver = {
+ .probe = bcm2711_thermal_probe,
+ .remove = bcm2711_thermal_remove,
+ .driver = {
+ .name = "bcm2711_thermal",
+ .of_match_table = bcm2711_thermal_id_table,
+ },
+};
+module_platform_driver(bcm2711_thermal_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Stefan Wahren");
+MODULE_DESCRIPTION("Broadcom AVS RO thermal sensor driver");
This adds the thermal sensor driver for the Broadcom BCM2711 SoC, which is placed on the Raspberry Pi 4. The driver only provides SoC temperature reading so far. Signed-off-by: Stefan Wahren <wahrenst@gmx.net> --- drivers/thermal/broadcom/Kconfig | 8 ++ drivers/thermal/broadcom/Makefile | 1 + drivers/thermal/broadcom/bcm2711_thermal.c | 146 +++++++++++++++++++++++++++++ 3 files changed, 155 insertions(+) create mode 100644 drivers/thermal/broadcom/bcm2711_thermal.c -- 2.7.4