| Message ID | 20160901212700.29747-1-contact@paulk.fr (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
Hi Paul, This looks mostly fine now. I have a few more comments, that I missed last time: On Thu, Sep 01, 2016 at 11:27:00PM +0200, Paul Kocialkowski wrote: > This requests the status GPIO with initial input setup. it is required > to read the GPIO status at probe time and thus correctly avoid sending > i2c messages when AC is not plugged. > > When requesting the GPIO without initial input setup, it always reads 0 > which causes probe to fail as it assumes the charger is connected, sends > i2c messages and fails. > > While at it, this switches the driver over to gpio consumer. > > Signed-off-by: Paul Kocialkowski <contact@paulk.fr> > --- > drivers/power/bq24735-charger.c | 42 +++++++++++++---------------------- > include/linux/power/bq24735-charger.h | 4 +--- > 2 files changed, 17 insertions(+), 29 deletions(-) Please rebase next version to power-supply's for-next branch: https://git.kernel.org/cgit/linux/kernel/git/sre/linux-power-supply.git/log/?h=for-next > diff --git a/drivers/power/bq24735-charger.c b/drivers/power/bq24735-charger.c > index dc460bb..7f9b305 100644 > --- a/drivers/power/bq24735-charger.c > +++ b/drivers/power/bq24735-charger.c > @@ -25,7 +25,8 @@ > #include <linux/kernel.h> > #include <linux/module.h> > #include <linux/of.h> > -#include <linux/of_gpio.h> > +#include <linux/gpio.h> No need for <linux/gpio.h>, all gpiod bits used by you are in <linux/gpio/consumer.h> > +#include <linux/gpio/consumer.h> > #include <linux/power_supply.h> > #include <linux/slab.h> > > @@ -178,11 +179,9 @@ static int bq24735_config_charger(struct bq24735 *charger) > static bool bq24735_charger_is_present(struct bq24735 *charger) > { > struct bq24735_platform *pdata = charger->pdata; > - int ret; > > - if (pdata->status_gpio_valid) { > - ret = gpio_get_value_cansleep(pdata->status_gpio); > - return ret ^= pdata->status_gpio_active_low == 0; > + if (pdata->status_gpio) { > + return !gpiod_get_value_cansleep(pdata->status_gpio); > } else { > int ac = 0; > > @@ -308,7 +307,6 @@ static struct bq24735_platform *bq24735_parse_dt_data(struct i2c_client *client) > struct device_node *np = client->dev.of_node; > u32 val; > int ret; > - enum of_gpio_flags flags; > > pdata = devm_kzalloc(&client->dev, sizeof(*pdata), GFP_KERNEL); > if (!pdata) { > @@ -317,11 +315,13 @@ static struct bq24735_platform *bq24735_parse_dt_data(struct i2c_client *client) > return NULL; > } > > - pdata->status_gpio = of_get_named_gpio_flags(np, "ti,ac-detect-gpios", > - 0, &flags); > - > - if (flags & OF_GPIO_ACTIVE_LOW) > - pdata->status_gpio_active_low = 1; > + pdata->status_gpio = devm_gpiod_get_optional(&client->dev, > + "ti,ac-detect", GPIOD_IN); > + if (IS_ERR(pdata->status_gpio)) { > + ret = PTR_ERR(pdata->status_gpio); > + dev_err(&client->dev, "Getting gpio failed: %d\n", ret); > + return (struct bq24735_platform *) pdata->status_gpio; > + } > > ret = of_property_read_u32(np, "ti,charge-current", &val); > if (!ret) > @@ -357,8 +357,11 @@ static int bq24735_charger_probe(struct i2c_client *client, > charger->charging = true; > charger->pdata = client->dev.platform_data; > > - if (IS_ENABLED(CONFIG_OF) && !charger->pdata && client->dev.of_node) > + if (IS_ENABLED(CONFIG_OF) && !charger->pdata && client->dev.of_node) { > charger->pdata = bq24735_parse_dt_data(client); > + if (IS_ERR(charger->pdata)) > + return PTR_ERR(charger->pdata); > + } > > if (!charger->pdata) { > dev_err(&client->dev, "no platform data provided\n"); > @@ -396,20 +399,7 @@ static int bq24735_charger_probe(struct i2c_client *client, > > i2c_set_clientdata(client, charger); > > - if (gpio_is_valid(charger->pdata->status_gpio)) { > - ret = devm_gpio_request(&client->dev, > - charger->pdata->status_gpio, > - name); > - if (ret) { > - dev_err(&client->dev, > - "Failed GPIO request for GPIO %d: %d\n", > - charger->pdata->status_gpio, ret); > - } > - > - charger->pdata->status_gpio_valid = !ret; > - } Do the devm_gpiod_get_optional() call here and store the result in "struct bq24735" instead of in pdata. It's not DT specific. The gpiod interface can also get it's data from boardcode (or acpi, if that becomes important at some point). (Check Documentation/gpio/board.txt for details) > - > - if (!charger->pdata->status_gpio_valid > + if (!charger->pdata->status_gpio > || bq24735_charger_is_present(charger)) { > ret = bq24735_read_word(client, BQ24735_MANUFACTURER_ID); > if (ret < 0) { > diff --git a/include/linux/power/bq24735-charger.h b/include/linux/power/bq24735-charger.h > index 6b750c1a..afdb3704 100644 > --- a/include/linux/power/bq24735-charger.h > +++ b/include/linux/power/bq24735-charger.h > @@ -28,9 +28,7 @@ struct bq24735_platform { > > const char *name; > > - int status_gpio; > - int status_gpio_active_low; > - bool status_gpio_valid; > + struct gpio_desc *status_gpio; Move the gpio_desc into the private "struct bq24735" (but keep dropping all gpio bits from the bq24735_platform). -- Sebastian
Hi, Le vendredi 02 septembre 2016 à 17:27 +0200, Sebastian Reichel a écrit : > Hi Paul, > > This looks mostly fine now. I have a few more comments, that I > missed last time: Thanks for the review and for the useful suggestions. I have applied them to v4. > On Thu, Sep 01, 2016 at 11:27:00PM +0200, Paul Kocialkowski wrote: > > > > This requests the status GPIO with initial input setup. it is required > > to read the GPIO status at probe time and thus correctly avoid sending > > i2c messages when AC is not plugged. > > > > When requesting the GPIO without initial input setup, it always reads 0 > > which causes probe to fail as it assumes the charger is connected, sends > > i2c messages and fails. > > > > While at it, this switches the driver over to gpio consumer. > > > > Signed-off-by: Paul Kocialkowski <contact@paulk.fr> > > --- > > drivers/power/bq24735-charger.c | 42 +++++++++++++------------------- > > --- > > include/linux/power/bq24735-charger.h | 4 +--- > > 2 files changed, 17 insertions(+), 29 deletions(-) > > Please rebase next version to power-supply's for-next branch: > > https://git.kernel.org/cgit/linux/kernel/git/sre/linux-power-supply.git/log/?h > =for-next > > > > > diff --git a/drivers/power/bq24735-charger.c b/drivers/power/bq24735- > > charger.c > > index dc460bb..7f9b305 100644 > > --- a/drivers/power/bq24735-charger.c > > +++ b/drivers/power/bq24735-charger.c > > @@ -25,7 +25,8 @@ > > #include <linux/kernel.h> > > #include <linux/module.h> > > #include <linux/of.h> > > -#include <linux/of_gpio.h> > > +#include <linux/gpio.h> > > No need for <linux/gpio.h>, all gpiod bits used by you are in > <linux/gpio/consumer.h> > > > > > +#include <linux/gpio/consumer.h> > > #include <linux/power_supply.h> > > #include <linux/slab.h> > > > > @@ -178,11 +179,9 @@ static int bq24735_config_charger(struct bq24735 > > *charger) > > static bool bq24735_charger_is_present(struct bq24735 *charger) > > { > > struct bq24735_platform *pdata = charger->pdata; > > - int ret; > > > > - if (pdata->status_gpio_valid) { > > - ret = gpio_get_value_cansleep(pdata->status_gpio); > > - return ret ^= pdata->status_gpio_active_low == 0; > > + if (pdata->status_gpio) { > > + return !gpiod_get_value_cansleep(pdata->status_gpio); > > } else { > > int ac = 0; > > > > @@ -308,7 +307,6 @@ static struct bq24735_platform > > *bq24735_parse_dt_data(struct i2c_client *client) > > struct device_node *np = client->dev.of_node; > > u32 val; > > int ret; > > - enum of_gpio_flags flags; > > > > pdata = devm_kzalloc(&client->dev, sizeof(*pdata), GFP_KERNEL); > > if (!pdata) { > > @@ -317,11 +315,13 @@ static struct bq24735_platform > > *bq24735_parse_dt_data(struct i2c_client *client) > > return NULL; > > } > > > > - pdata->status_gpio = of_get_named_gpio_flags(np, "ti,ac-detect- > > gpios", > > - 0, &flags); > > - > > - if (flags & OF_GPIO_ACTIVE_LOW) > > - pdata->status_gpio_active_low = 1; > > + pdata->status_gpio = devm_gpiod_get_optional(&client->dev, > > + "ti,ac-detect", GPIOD_IN); > > + if (IS_ERR(pdata->status_gpio)) { > > + ret = PTR_ERR(pdata->status_gpio); > > + dev_err(&client->dev, "Getting gpio failed: %d\n", ret); > > + return (struct bq24735_platform *) pdata->status_gpio; > > + } > > > > ret = of_property_read_u32(np, "ti,charge-current", &val); > > if (!ret) > > @@ -357,8 +357,11 @@ static int bq24735_charger_probe(struct i2c_client > > *client, > > charger->charging = true; > > charger->pdata = client->dev.platform_data; > > > > - if (IS_ENABLED(CONFIG_OF) && !charger->pdata && client- > > >dev.of_node) > > + if (IS_ENABLED(CONFIG_OF) && !charger->pdata && client- > > >dev.of_node) { > > charger->pdata = bq24735_parse_dt_data(client); > > + if (IS_ERR(charger->pdata)) > > + return PTR_ERR(charger->pdata); > > + } > > > > if (!charger->pdata) { > > dev_err(&client->dev, "no platform data provided\n"); > > @@ -396,20 +399,7 @@ static int bq24735_charger_probe(struct i2c_client > > *client, > > > > i2c_set_clientdata(client, charger); > > > > - if (gpio_is_valid(charger->pdata->status_gpio)) { > > - ret = devm_gpio_request(&client->dev, > > - charger->pdata->status_gpio, > > - name); > > - if (ret) { > > - dev_err(&client->dev, > > - "Failed GPIO request for GPIO %d: %d\n", > > - charger->pdata->status_gpio, ret); > > - } > > - > > - charger->pdata->status_gpio_valid = !ret; > > - } > > Do the devm_gpiod_get_optional() call here and store the result in > "struct bq24735" instead of in pdata. It's not DT specific. The > gpiod interface can also get it's data from boardcode (or acpi, if > that becomes important at some point). > > (Check Documentation/gpio/board.txt for details) > > > > > - > > - if (!charger->pdata->status_gpio_valid > > + if (!charger->pdata->status_gpio > > || bq24735_charger_is_present(charger)) { > > ret = bq24735_read_word(client, BQ24735_MANUFACTURER_ID); > > if (ret < 0) { > > diff --git a/include/linux/power/bq24735-charger.h > > b/include/linux/power/bq24735-charger.h > > index 6b750c1a..afdb3704 100644 > > --- a/include/linux/power/bq24735-charger.h > > +++ b/include/linux/power/bq24735-charger.h > > @@ -28,9 +28,7 @@ struct bq24735_platform { > > > > const char *name; > > > > - int status_gpio; > > - int status_gpio_active_low; > > - bool status_gpio_valid; > > + struct gpio_desc *status_gpio; > > Move the gpio_desc into the private "struct bq24735" (but keep > dropping all gpio bits from the bq24735_platform). > > -- Sebastian
diff --git a/drivers/power/bq24735-charger.c b/drivers/power/bq24735-charger.c index dc460bb..7f9b305 100644 --- a/drivers/power/bq24735-charger.c +++ b/drivers/power/bq24735-charger.c @@ -25,7 +25,8 @@ #include <linux/kernel.h> #include <linux/module.h> #include <linux/of.h> -#include <linux/of_gpio.h> +#include <linux/gpio.h> +#include <linux/gpio/consumer.h> #include <linux/power_supply.h> #include <linux/slab.h> @@ -178,11 +179,9 @@ static int bq24735_config_charger(struct bq24735 *charger) static bool bq24735_charger_is_present(struct bq24735 *charger) { struct bq24735_platform *pdata = charger->pdata; - int ret; - if (pdata->status_gpio_valid) { - ret = gpio_get_value_cansleep(pdata->status_gpio); - return ret ^= pdata->status_gpio_active_low == 0; + if (pdata->status_gpio) { + return !gpiod_get_value_cansleep(pdata->status_gpio); } else { int ac = 0; @@ -308,7 +307,6 @@ static struct bq24735_platform *bq24735_parse_dt_data(struct i2c_client *client) struct device_node *np = client->dev.of_node; u32 val; int ret; - enum of_gpio_flags flags; pdata = devm_kzalloc(&client->dev, sizeof(*pdata), GFP_KERNEL); if (!pdata) { @@ -317,11 +315,13 @@ static struct bq24735_platform *bq24735_parse_dt_data(struct i2c_client *client) return NULL; } - pdata->status_gpio = of_get_named_gpio_flags(np, "ti,ac-detect-gpios", - 0, &flags); - - if (flags & OF_GPIO_ACTIVE_LOW) - pdata->status_gpio_active_low = 1; + pdata->status_gpio = devm_gpiod_get_optional(&client->dev, + "ti,ac-detect", GPIOD_IN); + if (IS_ERR(pdata->status_gpio)) { + ret = PTR_ERR(pdata->status_gpio); + dev_err(&client->dev, "Getting gpio failed: %d\n", ret); + return (struct bq24735_platform *) pdata->status_gpio; + } ret = of_property_read_u32(np, "ti,charge-current", &val); if (!ret) @@ -357,8 +357,11 @@ static int bq24735_charger_probe(struct i2c_client *client, charger->charging = true; charger->pdata = client->dev.platform_data; - if (IS_ENABLED(CONFIG_OF) && !charger->pdata && client->dev.of_node) + if (IS_ENABLED(CONFIG_OF) && !charger->pdata && client->dev.of_node) { charger->pdata = bq24735_parse_dt_data(client); + if (IS_ERR(charger->pdata)) + return PTR_ERR(charger->pdata); + } if (!charger->pdata) { dev_err(&client->dev, "no platform data provided\n"); @@ -396,20 +399,7 @@ static int bq24735_charger_probe(struct i2c_client *client, i2c_set_clientdata(client, charger); - if (gpio_is_valid(charger->pdata->status_gpio)) { - ret = devm_gpio_request(&client->dev, - charger->pdata->status_gpio, - name); - if (ret) { - dev_err(&client->dev, - "Failed GPIO request for GPIO %d: %d\n", - charger->pdata->status_gpio, ret); - } - - charger->pdata->status_gpio_valid = !ret; - } - - if (!charger->pdata->status_gpio_valid + if (!charger->pdata->status_gpio || bq24735_charger_is_present(charger)) { ret = bq24735_read_word(client, BQ24735_MANUFACTURER_ID); if (ret < 0) { diff --git a/include/linux/power/bq24735-charger.h b/include/linux/power/bq24735-charger.h index 6b750c1a..afdb3704 100644 --- a/include/linux/power/bq24735-charger.h +++ b/include/linux/power/bq24735-charger.h @@ -28,9 +28,7 @@ struct bq24735_platform { const char *name; - int status_gpio; - int status_gpio_active_low; - bool status_gpio_valid; + struct gpio_desc *status_gpio; bool ext_control;
This requests the status GPIO with initial input setup. it is required to read the GPIO status at probe time and thus correctly avoid sending i2c messages when AC is not plugged. When requesting the GPIO without initial input setup, it always reads 0 which causes probe to fail as it assumes the charger is connected, sends i2c messages and fails. While at it, this switches the driver over to gpio consumer. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> --- drivers/power/bq24735-charger.c | 42 +++++++++++++---------------------- include/linux/power/bq24735-charger.h | 4 +--- 2 files changed, 17 insertions(+), 29 deletions(-)