diff mbox series

[v5,3/3] arm64: dts: qcom: pm8998: Add pm8998 thermal zone

Message ID 20180724234636.57137-3-mka@chromium.org (mailing list archive)
State Changes Requested
Delegated to: Eduardo Valentin
Headers show
Series [v5,1/3] thermal: qcom-spmi: Use PMIC thermal stage 2 for critical trip points | expand

Commit Message

Matthias Kaehlcke July 24, 2018, 11:46 p.m. UTC
The thermal zone uses spmi-temp-alarm as sensor, the trip points
correspond to the PMIC thermal stages 1 and 2. The critical trip
point at 125°C disables the partial PMIC shutdown at stage 2.

Without an IIO input the sensor only reports a limited number of
temperatures:

- 37°C for temperatures below 105°C
- 107°C for temperatures >= 105°C and < 125°C
- 127°C for temperatures >= 125°C

(the numbers correspond to a stage 1 threshold of 105°C)

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
---
Changes in v5:
- removed 'stage2-shutdown-disabled' property from spmi-temp-alarm
- updated commit message

Changes in v4:
- updated trip point temperatures to match stage 1 and 2 ones
- disabled stage 2 shutdown
- updated commit message

Changes in v3:
- moved 'thermal-zones' node to the beginning of the .dtsi

Changes in v2:
- defined 'thermal-zones' node in pm8998.dtsi instead of using a label
  to refer to it
- use 105°C hardware trip point as critical trip point
- reduced number of trip points to 2
- lowered temperature of passive trip point
- updated trip point names and added labels
- updated commit message
---
 arch/arm64/boot/dts/qcom/pm8998.dtsi | 25 +++++++++++++++++++++++++
 1 file changed, 25 insertions(+)

Comments

Doug Anderson July 25, 2018, 11:21 p.m. UTC | #1
Hi,

On Tue, Jul 24, 2018 at 4:46 PM, Matthias Kaehlcke <mka@chromium.org> wrote:
> The thermal zone uses spmi-temp-alarm as sensor, the trip points
> correspond to the PMIC thermal stages 1 and 2. The critical trip
> point at 125°C disables the partial PMIC shutdown at stage 2.
>
> Without an IIO input the sensor only reports a limited number of
> temperatures:
>
> - 37°C for temperatures below 105°C
> - 107°C for temperatures >= 105°C and < 125°C
> - 127°C for temperatures >= 125°C
>
> (the numbers correspond to a stage 1 threshold of 105°C)
>
> Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
> ---
> Changes in v5:
> - removed 'stage2-shutdown-disabled' property from spmi-temp-alarm
> - updated commit message
>
> Changes in v4:
> - updated trip point temperatures to match stage 1 and 2 ones
> - disabled stage 2 shutdown
> - updated commit message
>
> Changes in v3:
> - moved 'thermal-zones' node to the beginning of the .dtsi
>
> Changes in v2:
> - defined 'thermal-zones' node in pm8998.dtsi instead of using a label
>   to refer to it
> - use 105°C hardware trip point as critical trip point
> - reduced number of trip points to 2
> - lowered temperature of passive trip point
> - updated trip point names and added labels
> - updated commit message
> ---
>  arch/arm64/boot/dts/qcom/pm8998.dtsi | 25 +++++++++++++++++++++++++
>  1 file changed, 25 insertions(+)

Looks great!

Reviewed-by: Douglas Anderson <dianders@chromium.org>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi
index 7eea94701b23..34c259ba3919 100644
--- a/arch/arm64/boot/dts/qcom/pm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi
@@ -3,6 +3,31 @@ 
 
 #include <dt-bindings/spmi/spmi.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	thermal-zones {
+		pm8998 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&pm8998_temp>;
+
+			trips {
+				pm8998_alert0: pm8998-alert0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				pm8998_crit: pm8998-crit {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
 
 &spmi_bus {
 	pm8998_lsid0: pmic@0 {