| Message ID | 20220505015814.3727692-3-rui.zhang@intel.com (mailing list archive) |
|---|---|
| State | Changes Requested, archived |
| Headers | show |
| Series | PM: Solution for S0ix failure caused by PCH overheating | expand |
On Thu, May 5, 2022 at 3:58 AM Zhang Rui <rui.zhang@intel.com> wrote: > > Commit ef63b043ac86 ("thermal: intel: pch: fix S0ix failure due to PCH > temperature above threshold") introduces delay loop mechanism that allows > PCH temperature to go down below threshold during suspend so it won't > block S0ix. And the default overall delay timeout is 1 second. > > However, in practice, we found that the time it takes to cool the PCH down > below threshold highly depends on the initial PCH temperature when the > delay starts, as well as the ambient temperature. > And in some cases, the 1 second delay is not sufficient. As a result, the > system stays in a shallower power state like PCx instead of S0ix, and > drains the battery power, without user' notice. > > To make sure S0ix is not blocked by the PCH overheating, we > 1. expand the default overall timeout to 60 seconds. > 2. make sure the temperature is below threshold rather than equal to it. > 3. move the delay to .suspend_noirq phase instead, in order to > a) do cooling delay with a more quiescent system > b) be aware of wakeup events during the long delay, because some wakeup > events (ACPI Power button Press, USB mouse, etc) become valid only > in .suspend_noirq phase and later. > > This may introduce longer suspend time, but only in the cases when the > system overheats and Linux used to enter a shallower S2idle state, say, > PCx instead of S0ix. > > Signed-off-by: Zhang Rui <rui.zhang@intel.com> > Tested-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> > --- > drivers/thermal/intel/intel_pch_thermal.c | 18 +++++++++++------- > 1 file changed, 11 insertions(+), 7 deletions(-) > > diff --git a/drivers/thermal/intel/intel_pch_thermal.c b/drivers/thermal/intel/intel_pch_thermal.c > index 527c91f5960b..b7b32e2f5ae2 100644 > --- a/drivers/thermal/intel/intel_pch_thermal.c > +++ b/drivers/thermal/intel/intel_pch_thermal.c > @@ -70,8 +70,8 @@ static unsigned int delay_timeout = 100; > module_param(delay_timeout, int, 0644); > MODULE_PARM_DESC(delay_timeout, "amount of time delay for each iteration."); > > -/* Number of iterations for cooling delay, 10 counts by default for now */ > -static unsigned int delay_cnt = 10; > +/* Number of iterations for cooling delay, 600 counts by default for now */ > +static unsigned int delay_cnt = 600; > module_param(delay_cnt, int, 0644); > MODULE_PARM_DESC(delay_cnt, "total number of iterations for time delay."); > > @@ -193,10 +193,11 @@ static int pch_wpt_get_temp(struct pch_thermal_device *ptd, int *temp) > return 0; > } > > +/* Cool the PCH when it's overheat in .suspend_noirq phase */ > static int pch_wpt_suspend(struct pch_thermal_device *ptd) > { > u8 tsel; > - u8 pch_delay_cnt = 1; > + int pch_delay_cnt = 1; > u16 pch_thr_temp, pch_cur_temp; > > /* Shutdown the thermal sensor if it is not enabled by BIOS */ > @@ -233,7 +234,10 @@ static int pch_wpt_suspend(struct pch_thermal_device *ptd) > * which helps to indentify the reason why S0ix entry was rejected. > */ > while (pch_delay_cnt <= delay_cnt) { > - if (pch_cur_temp <= pch_thr_temp) > + if (pch_cur_temp < pch_thr_temp) > + break; > + > + if (pm_wakeup_pending()) > break; > > dev_warn(&ptd->pdev->dev, > @@ -245,7 +249,7 @@ static int pch_wpt_suspend(struct pch_thermal_device *ptd) > pch_delay_cnt++; > } > > - if (pch_cur_temp > pch_thr_temp) > + if (pch_cur_temp >= pch_thr_temp) > dev_warn(&ptd->pdev->dev, > "CPU-PCH is hot [%dC] even after delay, continue to suspend. S0ix might fail\n", > pch_cur_temp); > @@ -455,7 +459,7 @@ static void intel_pch_thermal_remove(struct pci_dev *pdev) > pci_disable_device(pdev); > } > > -static int intel_pch_thermal_suspend(struct device *device) > +static int intel_pch_thermal_suspend_noirq(struct device *device) > { > struct pch_thermal_device *ptd = dev_get_drvdata(device); > > @@ -495,7 +499,7 @@ static const struct pci_device_id intel_pch_thermal_id[] = { > MODULE_DEVICE_TABLE(pci, intel_pch_thermal_id); > > static const struct dev_pm_ops intel_pch_pm_ops = { > - .suspend = intel_pch_thermal_suspend, > + .suspend_noirq = intel_pch_thermal_suspend_noirq, IMO it would be better to put this change into a separate patch and reorder the other changes after this one. It is valid by itself. > .resume = intel_pch_thermal_resume, > }; > > --
diff --git a/drivers/thermal/intel/intel_pch_thermal.c b/drivers/thermal/intel/intel_pch_thermal.c index 527c91f5960b..b7b32e2f5ae2 100644 --- a/drivers/thermal/intel/intel_pch_thermal.c +++ b/drivers/thermal/intel/intel_pch_thermal.c @@ -70,8 +70,8 @@ static unsigned int delay_timeout = 100; module_param(delay_timeout, int, 0644); MODULE_PARM_DESC(delay_timeout, "amount of time delay for each iteration."); -/* Number of iterations for cooling delay, 10 counts by default for now */ -static unsigned int delay_cnt = 10; +/* Number of iterations for cooling delay, 600 counts by default for now */ +static unsigned int delay_cnt = 600; module_param(delay_cnt, int, 0644); MODULE_PARM_DESC(delay_cnt, "total number of iterations for time delay."); @@ -193,10 +193,11 @@ static int pch_wpt_get_temp(struct pch_thermal_device *ptd, int *temp) return 0; } +/* Cool the PCH when it's overheat in .suspend_noirq phase */ static int pch_wpt_suspend(struct pch_thermal_device *ptd) { u8 tsel; - u8 pch_delay_cnt = 1; + int pch_delay_cnt = 1; u16 pch_thr_temp, pch_cur_temp; /* Shutdown the thermal sensor if it is not enabled by BIOS */ @@ -233,7 +234,10 @@ static int pch_wpt_suspend(struct pch_thermal_device *ptd) * which helps to indentify the reason why S0ix entry was rejected. */ while (pch_delay_cnt <= delay_cnt) { - if (pch_cur_temp <= pch_thr_temp) + if (pch_cur_temp < pch_thr_temp) + break; + + if (pm_wakeup_pending()) break; dev_warn(&ptd->pdev->dev, @@ -245,7 +249,7 @@ static int pch_wpt_suspend(struct pch_thermal_device *ptd) pch_delay_cnt++; } - if (pch_cur_temp > pch_thr_temp) + if (pch_cur_temp >= pch_thr_temp) dev_warn(&ptd->pdev->dev, "CPU-PCH is hot [%dC] even after delay, continue to suspend. S0ix might fail\n", pch_cur_temp); @@ -455,7 +459,7 @@ static void intel_pch_thermal_remove(struct pci_dev *pdev) pci_disable_device(pdev); } -static int intel_pch_thermal_suspend(struct device *device) +static int intel_pch_thermal_suspend_noirq(struct device *device) { struct pch_thermal_device *ptd = dev_get_drvdata(device); @@ -495,7 +499,7 @@ static const struct pci_device_id intel_pch_thermal_id[] = { MODULE_DEVICE_TABLE(pci, intel_pch_thermal_id); static const struct dev_pm_ops intel_pch_pm_ops = { - .suspend = intel_pch_thermal_suspend, + .suspend_noirq = intel_pch_thermal_suspend_noirq, .resume = intel_pch_thermal_resume, };
Commit ef63b043ac86 ("thermal: intel: pch: fix S0ix failure due to PCH temperature above threshold") introduces delay loop mechanism that allows PCH temperature to go down below threshold during suspend so it won't block S0ix. And the default overall delay timeout is 1 second. However, in practice, we found that the time it takes to cool the PCH down below threshold highly depends on the initial PCH temperature when the delay starts, as well as the ambient temperature. And in some cases, the 1 second delay is not sufficient. As a result, the system stays in a shallower power state like PCx instead of S0ix, and drains the battery power, without user' notice. To make sure S0ix is not blocked by the PCH overheating, we 1. expand the default overall timeout to 60 seconds. 2. make sure the temperature is below threshold rather than equal to it. 3. move the delay to .suspend_noirq phase instead, in order to a) do cooling delay with a more quiescent system b) be aware of wakeup events during the long delay, because some wakeup events (ACPI Power button Press, USB mouse, etc) become valid only in .suspend_noirq phase and later. This may introduce longer suspend time, but only in the cases when the system overheats and Linux used to enter a shallower S2idle state, say, PCx instead of S0ix. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Tested-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> --- drivers/thermal/intel/intel_pch_thermal.c | 18 +++++++++++------- 1 file changed, 11 insertions(+), 7 deletions(-)