| Message ID | 20230103010904.3201835-7-bryan.odonoghue@linaro.org (mailing list archive) |
|---|---|
| State | Handled Elsewhere, archived |
| Headers | show |
| Series | Add MSM8939 SoC support with two devices | expand |
On 3.01.2023 02:09, Bryan O'Donoghue wrote: > The apq8039-t2 is an apq8039 based board paired with a wcn3680b WiFi > chipset. > > Co-developed-by: Shawn Guo <shawn.guo@linaro.org> > Signed-off-by: Shawn Guo <shawn.guo@linaro.org> > Co-developed-by: Jun Nie <jun.nie@linaro.org> > Signed-off-by: Jun Nie <jun.nie@linaro.org> > Co-developed-by: Benjamin Li <benl@squareup.com> > Signed-off-by: Benjamin Li <benl@squareup.com> > Co-developed-by: James Willcox <jwillcox@squareup.com> > Signed-off-by: James Willcox <jwillcox@squareup.com> > Co-developed-by: Leo Yan <leo.yan@linaro.org> > Signed-off-by: Leo Yan <leo.yan@linaro.org> > Co-developed-by: Joseph Gates <jgates@squareup.com> > Signed-off-by: Joseph Gates <jgates@squareup.com> > Co-developed-by: Max Chen <mchen@squareup.com> > Signed-off-by: Max Chen <mchen@squareup.com> > Co-developed-by: Zac Crosby <zac@squareup.com> > Signed-off-by: Zac Crosby <zac@squareup.com> > Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > arch/arm64/boot/dts/qcom/apq8039-t2.dts | 557 ++++++++++++++++++++++++ > 2 files changed, 558 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/apq8039-t2.dts > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 3e79496292e7a..8d8dab62c66df 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -1,5 +1,6 @@ > # SPDX-License-Identifier: GPL-2.0 > dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb > +dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb > diff --git a/arch/arm64/boot/dts/qcom/apq8039-t2.dts b/arch/arm64/boot/dts/qcom/apq8039-t2.dts > new file mode 100644 > index 0000000000000..04a2fdd1b1194 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/apq8039-t2.dts > @@ -0,0 +1,557 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (c) 2015, The Linux Foundation. All rights reserved. > + * Copyright (c) 2020-2023, Linaro Ltd. > + * > + */ > + > +/dts-v1/; > + > +#include "msm8939.dtsi" > +#include "msm8939-pm8916.dtsi" > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> > +#include <dt-bindings/sound/apq8016-lpass.h> > + > +/ { > + model = "Square, Inc. T2 Devkit"; > + compatible = "square,apq8039-t2", "qcom,msm8939"; > + qcom,board-id = <0x53 0x54>; > + > + aliases { > + serial0 = &blsp1_uart1; > + serial1 = &blsp1_uart2; > + }; > + > + bl: backlight { > + compatible = "gpio-backlight"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_backlight>; > + gpios = <&msmgpio 98 GPIO_ACTIVE_HIGH>; > + }; > + > + chosen { > + stdout-path = "serial1:115200n8"; > + }; > + > + lcd_iovcc_reg: lcd-iovcc-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "lcd_iovcc"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_lcd_iovcc_reg>; > + gpio = <&msmgpio 9 GPIO_ACTIVE_HIGH>; > + startup-delay-us = <300>; > + enable-active-high; > + }; > + > + lcd_avdd_reg: lcd-avdd-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "lcd_avdd"; > + regulator-min-microvolt = <5600000>; > + regulator-max-microvolt = <5600000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_lcd_avdd_reg>; > + gpio = <&msmgpio 86 GPIO_ACTIVE_HIGH>; > + startup-delay-us = <300>; > + enable-active-high; > + }; > + > + lcd_avee_reg: lcd-avee-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "lcd_avee"; > + regulator-min-microvolt = <5600000>; > + regulator-max-microvolt = <5600000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_lcd_avee_reg>; > + gpio = <&msmgpio 87 GPIO_ACTIVE_HIGH>; > + startup-delay-us = <300>; > + enable-active-high; > + }; > + > + pp_spe_3v3_reg: pp-spe-3v3-regulator { > + compatible = "regulator-fixed"; > + pinctrl-names = "default"; > + pinctrl-0 = <&msmgpio_spe_reg>; > + regulator-name = "pp_spe_3v3"; > + gpio = <&msmgpio 108 GPIO_ACTIVE_HIGH>; > + startup-delay-us = <0>; > + enable-active-high; > + }; > + > + pp_crq_3v3_reg: pp-crq-3v3-regulator { > + compatible = "regulator-fixed"; > + pinctrl-names = "default"; > + pinctrl-0 = <&msmgpio_crq_reg>; > + regulator-name = "pp_crq_3v3"; > + gpio = <&msmgpio 12 GPIO_ACTIVE_HIGH>; > + startup-delay-us = <0>; > + enable-active-high; > + }; > +}; > + > +&blsp_dma { > + status = "okay"; > +}; > + > +&blsp_i2c1 { > + status = "okay"; > +}; > + > +&blsp_i2c2 { > + status = "okay"; > +}; > + > +&blsp_i2c3 { > + status = "okay"; Please add a newline between last properties and first subnodes, on all appearances. > + tps6598x: tps6598x@38 { > + compatible = "ti,tps6598x"; > + reg = <0x38>; > + > + interrupt-parent = <&msmgpio>; > + interrupts = <107 IRQ_TYPE_LEVEL_LOW>; > + interrupt-names = "irq"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&typec_irq>; > + > + typec_con: connector { > + compatible = "usb-c-connector"; > + label = "USB-C"; > + port { > + typec_ep: endpoint { > + remote-endpoint = <&otg_ep>; > + }; > + }; > + }; > + }; > +}; > + > +&blsp_i2c5 { > + status = "okay"; > +}; > + > +&blsp1_uart1 { > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&blsp1_uart1_default>; > + pinctrl-1 = <&blsp1_uart1_sleep>; > + status = "okay"; > +}; > + > +&blsp1_uart2 { > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&blsp1_uart2_default>; > + pinctrl-1 = <&blsp1_uart2_sleep>; > + status = "okay"; > +}; > + > +&lpass { > + status = "okay"; > +}; > + > +/* > + * Line names are taken from the schematic of T2, Ver X03. > + * July 14, 2018. Page 4 in particular. Very cool that you provide these! > + */ > + > +&msmgpio { > + gpio-line-names = > + "APQ_UART1_TX", /* GPIO_0 */ > + "APQ_UART1_RX", > + "APQ_I2C1_SDA", > + "APQ_I2C1_SCL", > + "APQ_UART2_TX_1V8", > + "APQ_UART2_RX_1V8", > + "APQ_I2C2_SDA", > + "APQ_I2C2_SCL", > + "NC", > + "APQ_LCD_IOVCC_EN", > + "APQ_I2C3_SDA", /* GPIO_10 */ > + "APQ_I2C3_SCL", > + "TOUCH_RST_1V8_L", > + "NC", > + "APQ_I2C4_SDA", > + "APQ_I2C4_SCL", > + "APQ_ID5", > + "USB_DISCONNECT", > + "APQ_I2C5_SDA", > + "APQ_I2C5_SCL", > + "APQ_USBC_SPI_MOSI", /* GPIO_20 */ > + "APQ_USBC_SPI_MISO", > + "APQ_USBC_SPI_SS_L", > + "APQ_USBC_SPI_CLK", > + "APQ_LCD_TE0", > + "APQ_LCD_RST_L", > + "NC", > + "NC", > + "ACCELEROMETER_INT1", > + "APQ_CAM_I2C0_SDA", > + "APQ_CAM_I2C0_SCL", /* GPIO_30 */ > + "ACCELEROMETER_INT2", > + "NC", > + "NC", > + "NC", > + "APQ_K21_RST_1V8_L", > + "NC", > + "APQ_EDL_1V8", > + "TP145", > + "BT_SSBI", > + "NC", /* GPIO_40 */ > + "NC", > + "NC", > + "NC", > + "NC", > + "NC", > + "NC", > + "BT_CTRL", > + "BT_DAT", > + "PWR_GPIO_IN", > + "PWR_GPIO_OUT", /* GPIO_50 */ > + "CARD_DET_MLB_L", > + "HALL_SENSOR", > + "TP63", > + "TP64", > + "TP65", > + "NC", > + "NC", > + "NC", > + "NC", > + "NC", /* GPIO_60 */ > + "NC", > + "APQ_K21_GPIO0_1V8", > + "CDC_PDM_CLK", > + "CDC_PDM_SYNC", > + "CDC_PDM_TX", > + "CDC_PDM_RX0", > + "CDC_PDM_RX1", > + "CDC_PDM_RX2", > + "APQ_K21_GPIO1_1V8", > + "NC", /* GPIO_70 */ > + "APQ_HUB_SEL_1V8", > + "APQ_K21_GPIO2_1V8", > + "APQ_K21_GPIO3_1V8", > + "APQ_ID0", > + "APQ_ID1", > + "APQ_ID2", > + "APQ_ID3", > + "APQ_ID4", > + "APQ_HUB_SUSP_IND", > + "BOOT_CONFIG_0", /* GPIO_80 */ > + "BOOT_CONFIG_1", > + "BOOT_CONFIG_2", > + "BOOT_CONFIG_3", > + "NC", > + "NC", > + "APQ_LCD_AVDD_EN", > + "APQ_LCD_AVEE_EN", > + "TP70", > + "NC", > + "APQ_DEBUG0", /* GPIO_90 */ > + "APQ_DEBUG1", > + "APQ_DEBUG2", > + "APQ_DEBUG3", > + "TP165", > + "NC", > + "APQ_LNA_PWR_EN", > + "NC", > + "APQ_LCD_BL_EN", > + "NC", > + "APQ_LCD_ID0", /* GPIO_100 */ > + "APQ_LCD_ID1", > + "USBC_GPIO5_1V8", > + "NC", > + "NC", > + "NC", > + "APQ_HUB_RST_1V8_L", > + "USBC_I2C_IRQ_1V8_L", > + "SPE_PWR_EN", > + "NC", > + "APQ_USB_ID", /* GPIO_110 */ > + "APQ_EXT_BUCK_VSEL", > + "APQ_USB_ID_OUT", > + "NC", > + "PRNT_RST_L", > + "APQ_CRQ_I2C_RDY_1V8", > + "TYPEC_RST_1V8_H", > + "CHG_BACKPWR_EN", > + "CHG_PROCHOT_L", > + "NC", > + "USBC_GPIO7_1V8", /* GPIO_120 */ > + "NC"; > + > + blsp1_uart1_default: blsp1-uart1-default-state { Since the nodes are not sorted by name and since you provided the GPIO line names, maybe it would be nicer to sort them by gpio number for easy lookup? > + pins = "gpio0", "gpio1"; > + function = "blsp_uart1"; > + Please remove this newline. > + drive-strength = <16>; > + bias-disable; > + }; > + > + blsp1_uart1_sleep: blsp1-uart1-sleep-state { > + pins = "gpio0", "gpio1"; > + function = "gpio"; > + Ditto. > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + pinctrl_lcd_iovcc_reg: lcd-iovcc-reg-state { > + pins = "gpio9"; > + function = "gpio"; > + }; > + > + pinctrl_lcd_avdd_reg: lcd-avdd-reg-state { > + pins = "gpio86"; > + function = "gpio"; > + }; > + > + pinctrl_lcd_avee_reg: lcd-avee-reg-state { > + pins = "gpio87"; > + function = "gpio"; > + }; > + > + pinctrl_backlight: backlight-state { > + pins = "gpio98"; > + function = "gpio"; > + }; > + > + pinctrl_lcd_rst: lcd-rst-state { > + pins = "gpio25"; > + function = "gpio"; > + }; > + > + msmgpio_spe_reg: msmgpio-spe-reg-state { > + pins = "gpio108"; > + function = "gpio"; > + output-high; > + }; > + > + sq_spe_enable: sq-spe-enable-state { > + pins = "gpio35"; > + function = "gpio"; > + output-low; > + }; > + > + msmgpio_crq_reg: msmgpio-crq-reg-state { > + function = "gpio"; > + pins = "gpio12"; > + output-high; > + }; > + > + typec_irq: typec-irq-state { > + function = "gpio"; > + pins = "gpio107"; > + bias-pull-up; > + input-enable; > + }; > + > + pinctrl_otg_default: otg-default-state { > + function = "gpio"; > + pins = "gpio17"; > + output-high; > + }; > + > + pinctrl_otg_host: otg-host-state { > + function = "gpio"; > + pins = "gpio17"; > + output-low; > + }; > + > + pinctrl_otg_device: otg-device-state { > + function = "gpio"; > + pins = "gpio17"; > + output-low; > + }; > + > + ext_buck_vsel_reg: ext-buck-vsel-reg-state { > + function = "gpio"; > + pins = "gpio111"; > + drive-strength = <2>; > + }; > +}; > + > +&pm8916_gpios { > + gpio-line-names = > + "PM_GPIO1", /* WIFI_GPIO1_PRE */ > + "PM_GPIO2", /* WIFI_GPIO2_PRE */ > + "PM_GPIO3", > + "PM_GPIO4"; > +}; > + > +&pronto { > + pinctrl-names = "default"; > + pinctrl-0 = <&wcnss_pin_a>; > + status = "okay"; > + > + iris { > + compatible = "qcom,wcn3680"; > + }; > +}; > + > +&smd_rpm_regulators { > + vdd_l1_l2_l3-supply = <&pm8916_s3>; > + vdd_l4_l5_l6-supply = <&pm8916_s4>; > + vdd_l7-supply = <&pm8916_s4>; > + > + pm8916_s3: s3 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1300000>; > + }; > + > + pm8916_s4: s4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2100000>; > + }; > + > + /* l1 is fixed to 1225000, but not connected in schematic */ > + > + pm8916_l2: l2 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + pm8916_l4: l4 { > + regulator-min-microvolt = <2050000>; > + regulator-max-microvolt = <2050000>; > + }; > + > + pm8916_l5: l5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + pm8916_l6: l6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + pm8916_l7: l7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + pm8916_l8: l8 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2900000>; > + }; > + > + pm8916_l9: l9 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + pm8916_l10: l10 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + pm8916_l11: l11 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + }; > + > + pm8916_l12: l12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + }; > + > + pm8916_l13: l13 { > + regulator-min-microvolt = <3075000>; > + regulator-max-microvolt = <3075000>; > + }; > + > + pm8916_l14: l14 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + pm8916_l15: l15 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + pm8916_l16: l16 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + pm8916_l17: l17 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2850000>; > + }; > + > + pm8916_l18: l18 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <2700000>; > + }; > +}; > + > +&sdhc_1 { > + vmmc-supply = <&pm8916_l8>; > + vqmmc-supply = <&pm8916_l5>; > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; > + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; > + status = "okay"; > +}; > + > +&sound { > + status = "okay"; Status should go last, seems like nodes following this one haven't been updated. > + pinctrl-0 = <&cdc_pdm_lines_act>; > + pinctrl-1 = <&cdc_pdm_lines_sus>; > + pinctrl-names = "default", "sleep"; You're not sorting pinctrl-N/names consistently, a recent suggestion was to keep pinctrl-N first, as with everything else (clocks/reg/power-domains/etc.) we do something and then something-names. Konrad > + model = "apq8039-square-sndcard"; > + audio-routing = "AMIC2", "MIC BIAS Internal2"; > + > + internal-codec-playback-dai-link { > + link-name = "WCD"; > + cpu { > + sound-dai = <&lpass MI2S_PRIMARY>; > + }; > + codec { > + sound-dai = <&lpass_codec 0>, <&wcd_codec 0>; > + }; > + }; > + > + internal-codec-capture-dai-link { > + link-name = "WCD-Capture"; > + cpu { > + sound-dai = <&lpass MI2S_TERTIARY>; > + }; > + codec { > + sound-dai = <&lpass_codec 1>, <&wcd_codec 1>; > + }; > + }; > +}; > + > +&usb { > + status = "okay"; > + usb-role-switch; > + > + pinctrl-names = "default", "host", "device"; > + pinctrl-0 = <&pinctrl_otg_default>; > + pinctrl-1 = <&pinctrl_otg_host>; > + pinctrl-2 = <&pinctrl_otg_device>; > + pin-switch-delay-us = <100000>; > + > + ulpi { > + usb_hs_phy: phy { > + v1p8-supply = <&pm8916_l7>; > + v3p3-supply = <&pm8916_l13>; > + }; > + }; > + port { > + otg_ep: endpoint { > + remote-endpoint = <&typec_ep>; > + }; > + }; > +}; > + > +&wcd_codec { > + status = "okay"; > + qcom,hphl-jack-type-normally-open; > + qcom,mbhc-vthreshold-low = <75 150 237 450 500>; > + qcom,mbhc-vthreshold-high = <75 150 237 450 500>; > +};
On 03/01/2023 02:09, Bryan O'Donoghue wrote: > The apq8039-t2 is an apq8039 based board paired with a wcn3680b WiFi > chipset. > > Co-developed-by: Shawn Guo <shawn.guo@linaro.org> > Signed-off-by: Shawn Guo <shawn.guo@linaro.org> > Co-developed-by: Jun Nie <jun.nie@linaro.org> > Signed-off-by: Jun Nie <jun.nie@linaro.org> > Co-developed-by: Benjamin Li <benl@squareup.com> (...) > + > +&blsp_i2c2 { > + status = "okay"; > +}; > + > +&blsp_i2c3 { > + status = "okay"; Blank line. > + tps6598x: tps6598x@38 { Node names should be generic. https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation > + compatible = "ti,tps6598x"; > + reg = <0x38>; > + Best regards, Krzysztof
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 3e79496292e7a..8d8dab62c66df 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -1,5 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb +dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb diff --git a/arch/arm64/boot/dts/qcom/apq8039-t2.dts b/arch/arm64/boot/dts/qcom/apq8039-t2.dts new file mode 100644 index 0000000000000..04a2fdd1b1194 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/apq8039-t2.dts @@ -0,0 +1,557 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2015, The Linux Foundation. All rights reserved. + * Copyright (c) 2020-2023, Linaro Ltd. + * + */ + +/dts-v1/; + +#include "msm8939.dtsi" +#include "msm8939-pm8916.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> +#include <dt-bindings/sound/apq8016-lpass.h> + +/ { + model = "Square, Inc. T2 Devkit"; + compatible = "square,apq8039-t2", "qcom,msm8939"; + qcom,board-id = <0x53 0x54>; + + aliases { + serial0 = &blsp1_uart1; + serial1 = &blsp1_uart2; + }; + + bl: backlight { + compatible = "gpio-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_backlight>; + gpios = <&msmgpio 98 GPIO_ACTIVE_HIGH>; + }; + + chosen { + stdout-path = "serial1:115200n8"; + }; + + lcd_iovcc_reg: lcd-iovcc-regulator { + compatible = "regulator-fixed"; + regulator-name = "lcd_iovcc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_iovcc_reg>; + gpio = <&msmgpio 9 GPIO_ACTIVE_HIGH>; + startup-delay-us = <300>; + enable-active-high; + }; + + lcd_avdd_reg: lcd-avdd-regulator { + compatible = "regulator-fixed"; + regulator-name = "lcd_avdd"; + regulator-min-microvolt = <5600000>; + regulator-max-microvolt = <5600000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_avdd_reg>; + gpio = <&msmgpio 86 GPIO_ACTIVE_HIGH>; + startup-delay-us = <300>; + enable-active-high; + }; + + lcd_avee_reg: lcd-avee-regulator { + compatible = "regulator-fixed"; + regulator-name = "lcd_avee"; + regulator-min-microvolt = <5600000>; + regulator-max-microvolt = <5600000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_avee_reg>; + gpio = <&msmgpio 87 GPIO_ACTIVE_HIGH>; + startup-delay-us = <300>; + enable-active-high; + }; + + pp_spe_3v3_reg: pp-spe-3v3-regulator { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&msmgpio_spe_reg>; + regulator-name = "pp_spe_3v3"; + gpio = <&msmgpio 108 GPIO_ACTIVE_HIGH>; + startup-delay-us = <0>; + enable-active-high; + }; + + pp_crq_3v3_reg: pp-crq-3v3-regulator { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&msmgpio_crq_reg>; + regulator-name = "pp_crq_3v3"; + gpio = <&msmgpio 12 GPIO_ACTIVE_HIGH>; + startup-delay-us = <0>; + enable-active-high; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp_i2c1 { + status = "okay"; +}; + +&blsp_i2c2 { + status = "okay"; +}; + +&blsp_i2c3 { + status = "okay"; + tps6598x: tps6598x@38 { + compatible = "ti,tps6598x"; + reg = <0x38>; + + interrupt-parent = <&msmgpio>; + interrupts = <107 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "irq"; + + pinctrl-names = "default"; + pinctrl-0 = <&typec_irq>; + + typec_con: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + port { + typec_ep: endpoint { + remote-endpoint = <&otg_ep>; + }; + }; + }; + }; +}; + +&blsp_i2c5 { + status = "okay"; +}; + +&blsp1_uart1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_uart1_default>; + pinctrl-1 = <&blsp1_uart1_sleep>; + status = "okay"; +}; + +&blsp1_uart2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_uart2_default>; + pinctrl-1 = <&blsp1_uart2_sleep>; + status = "okay"; +}; + +&lpass { + status = "okay"; +}; + +/* + * Line names are taken from the schematic of T2, Ver X03. + * July 14, 2018. Page 4 in particular. + */ + +&msmgpio { + gpio-line-names = + "APQ_UART1_TX", /* GPIO_0 */ + "APQ_UART1_RX", + "APQ_I2C1_SDA", + "APQ_I2C1_SCL", + "APQ_UART2_TX_1V8", + "APQ_UART2_RX_1V8", + "APQ_I2C2_SDA", + "APQ_I2C2_SCL", + "NC", + "APQ_LCD_IOVCC_EN", + "APQ_I2C3_SDA", /* GPIO_10 */ + "APQ_I2C3_SCL", + "TOUCH_RST_1V8_L", + "NC", + "APQ_I2C4_SDA", + "APQ_I2C4_SCL", + "APQ_ID5", + "USB_DISCONNECT", + "APQ_I2C5_SDA", + "APQ_I2C5_SCL", + "APQ_USBC_SPI_MOSI", /* GPIO_20 */ + "APQ_USBC_SPI_MISO", + "APQ_USBC_SPI_SS_L", + "APQ_USBC_SPI_CLK", + "APQ_LCD_TE0", + "APQ_LCD_RST_L", + "NC", + "NC", + "ACCELEROMETER_INT1", + "APQ_CAM_I2C0_SDA", + "APQ_CAM_I2C0_SCL", /* GPIO_30 */ + "ACCELEROMETER_INT2", + "NC", + "NC", + "NC", + "APQ_K21_RST_1V8_L", + "NC", + "APQ_EDL_1V8", + "TP145", + "BT_SSBI", + "NC", /* GPIO_40 */ + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "BT_CTRL", + "BT_DAT", + "PWR_GPIO_IN", + "PWR_GPIO_OUT", /* GPIO_50 */ + "CARD_DET_MLB_L", + "HALL_SENSOR", + "TP63", + "TP64", + "TP65", + "NC", + "NC", + "NC", + "NC", + "NC", /* GPIO_60 */ + "NC", + "APQ_K21_GPIO0_1V8", + "CDC_PDM_CLK", + "CDC_PDM_SYNC", + "CDC_PDM_TX", + "CDC_PDM_RX0", + "CDC_PDM_RX1", + "CDC_PDM_RX2", + "APQ_K21_GPIO1_1V8", + "NC", /* GPIO_70 */ + "APQ_HUB_SEL_1V8", + "APQ_K21_GPIO2_1V8", + "APQ_K21_GPIO3_1V8", + "APQ_ID0", + "APQ_ID1", + "APQ_ID2", + "APQ_ID3", + "APQ_ID4", + "APQ_HUB_SUSP_IND", + "BOOT_CONFIG_0", /* GPIO_80 */ + "BOOT_CONFIG_1", + "BOOT_CONFIG_2", + "BOOT_CONFIG_3", + "NC", + "NC", + "APQ_LCD_AVDD_EN", + "APQ_LCD_AVEE_EN", + "TP70", + "NC", + "APQ_DEBUG0", /* GPIO_90 */ + "APQ_DEBUG1", + "APQ_DEBUG2", + "APQ_DEBUG3", + "TP165", + "NC", + "APQ_LNA_PWR_EN", + "NC", + "APQ_LCD_BL_EN", + "NC", + "APQ_LCD_ID0", /* GPIO_100 */ + "APQ_LCD_ID1", + "USBC_GPIO5_1V8", + "NC", + "NC", + "NC", + "APQ_HUB_RST_1V8_L", + "USBC_I2C_IRQ_1V8_L", + "SPE_PWR_EN", + "NC", + "APQ_USB_ID", /* GPIO_110 */ + "APQ_EXT_BUCK_VSEL", + "APQ_USB_ID_OUT", + "NC", + "PRNT_RST_L", + "APQ_CRQ_I2C_RDY_1V8", + "TYPEC_RST_1V8_H", + "CHG_BACKPWR_EN", + "CHG_PROCHOT_L", + "NC", + "USBC_GPIO7_1V8", /* GPIO_120 */ + "NC"; + + blsp1_uart1_default: blsp1-uart1-default-state { + pins = "gpio0", "gpio1"; + function = "blsp_uart1"; + + drive-strength = <16>; + bias-disable; + }; + + blsp1_uart1_sleep: blsp1-uart1-sleep-state { + pins = "gpio0", "gpio1"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-down; + }; + + pinctrl_lcd_iovcc_reg: lcd-iovcc-reg-state { + pins = "gpio9"; + function = "gpio"; + }; + + pinctrl_lcd_avdd_reg: lcd-avdd-reg-state { + pins = "gpio86"; + function = "gpio"; + }; + + pinctrl_lcd_avee_reg: lcd-avee-reg-state { + pins = "gpio87"; + function = "gpio"; + }; + + pinctrl_backlight: backlight-state { + pins = "gpio98"; + function = "gpio"; + }; + + pinctrl_lcd_rst: lcd-rst-state { + pins = "gpio25"; + function = "gpio"; + }; + + msmgpio_spe_reg: msmgpio-spe-reg-state { + pins = "gpio108"; + function = "gpio"; + output-high; + }; + + sq_spe_enable: sq-spe-enable-state { + pins = "gpio35"; + function = "gpio"; + output-low; + }; + + msmgpio_crq_reg: msmgpio-crq-reg-state { + function = "gpio"; + pins = "gpio12"; + output-high; + }; + + typec_irq: typec-irq-state { + function = "gpio"; + pins = "gpio107"; + bias-pull-up; + input-enable; + }; + + pinctrl_otg_default: otg-default-state { + function = "gpio"; + pins = "gpio17"; + output-high; + }; + + pinctrl_otg_host: otg-host-state { + function = "gpio"; + pins = "gpio17"; + output-low; + }; + + pinctrl_otg_device: otg-device-state { + function = "gpio"; + pins = "gpio17"; + output-low; + }; + + ext_buck_vsel_reg: ext-buck-vsel-reg-state { + function = "gpio"; + pins = "gpio111"; + drive-strength = <2>; + }; +}; + +&pm8916_gpios { + gpio-line-names = + "PM_GPIO1", /* WIFI_GPIO1_PRE */ + "PM_GPIO2", /* WIFI_GPIO2_PRE */ + "PM_GPIO3", + "PM_GPIO4"; +}; + +&pronto { + pinctrl-names = "default"; + pinctrl-0 = <&wcnss_pin_a>; + status = "okay"; + + iris { + compatible = "qcom,wcn3680"; + }; +}; + +&smd_rpm_regulators { + vdd_l1_l2_l3-supply = <&pm8916_s3>; + vdd_l4_l5_l6-supply = <&pm8916_s4>; + vdd_l7-supply = <&pm8916_s4>; + + pm8916_s3: s3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + }; + + pm8916_s4: s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2100000>; + }; + + /* l1 is fixed to 1225000, but not connected in schematic */ + + pm8916_l2: l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + pm8916_l4: l4 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + pm8916_l5: l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8916_l6: l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8916_l7: l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8916_l8: l8 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2900000>; + }; + + pm8916_l9: l9 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + pm8916_l10: l10 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + pm8916_l11: l11 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + pm8916_l12: l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + pm8916_l13: l13 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + }; + + pm8916_l14: l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + pm8916_l15: l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + pm8916_l16: l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + pm8916_l17: l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + pm8916_l18: l18 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; +}; + +&sdhc_1 { + vmmc-supply = <&pm8916_l8>; + vqmmc-supply = <&pm8916_l5>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; + status = "okay"; +}; + +&sound { + status = "okay"; + pinctrl-0 = <&cdc_pdm_lines_act>; + pinctrl-1 = <&cdc_pdm_lines_sus>; + pinctrl-names = "default", "sleep"; + model = "apq8039-square-sndcard"; + audio-routing = "AMIC2", "MIC BIAS Internal2"; + + internal-codec-playback-dai-link { + link-name = "WCD"; + cpu { + sound-dai = <&lpass MI2S_PRIMARY>; + }; + codec { + sound-dai = <&lpass_codec 0>, <&wcd_codec 0>; + }; + }; + + internal-codec-capture-dai-link { + link-name = "WCD-Capture"; + cpu { + sound-dai = <&lpass MI2S_TERTIARY>; + }; + codec { + sound-dai = <&lpass_codec 1>, <&wcd_codec 1>; + }; + }; +}; + +&usb { + status = "okay"; + usb-role-switch; + + pinctrl-names = "default", "host", "device"; + pinctrl-0 = <&pinctrl_otg_default>; + pinctrl-1 = <&pinctrl_otg_host>; + pinctrl-2 = <&pinctrl_otg_device>; + pin-switch-delay-us = <100000>; + + ulpi { + usb_hs_phy: phy { + v1p8-supply = <&pm8916_l7>; + v3p3-supply = <&pm8916_l13>; + }; + }; + port { + otg_ep: endpoint { + remote-endpoint = <&typec_ep>; + }; + }; +}; + +&wcd_codec { + status = "okay"; + qcom,hphl-jack-type-normally-open; + qcom,mbhc-vthreshold-low = <75 150 237 450 500>; + qcom,mbhc-vthreshold-high = <75 150 237 450 500>; +};