diff --git a/arch/arm64/boot/dts/qcom/sm6115.dtsi b/arch/arm64/boot/dts/qcom/sm6115.dtsi
index 70a06249b130..dc78757a1ebb 100644
--- a/arch/arm64/boot/dts/qcom/sm6115.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6115.dtsi
@@ -10,6 +10,8 @@
 #include <dt-bindings/dma/qcom-gpi.h>
 #include <dt-bindings/firmware/qcom,scm.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interconnect/qcom,rpm-icc.h>
+#include <dt-bindings/interconnect/qcom,sm6115.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 
@@ -264,6 +266,8 @@ firmware {
 		scm: scm {
 			compatible = "qcom,scm-sm6115", "qcom,scm";
 			#reset-cells = <1>;
+			interconnects = <&system_noc MASTER_CRYPTO_CORE0 RPM_ALWAYS_TAG
+					 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>;
 		};
 	};
 
@@ -878,6 +882,43 @@ usb_qmpphy: phy@1615000 {
 			status = "disabled";
 		};
 
+		system_noc: interconnect@1880000 {
+			compatible = "qcom,sm6115-snoc";
+			reg = <0x0 0x01880000 0x0 0x5f080>;
+			clocks = <&gcc GCC_SYS_NOC_CPUSS_AHB_CLK>,
+				 <&gcc GCC_SYS_NOC_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_SYS_NOC_USB3_PRIM_AXI_CLK>,
+				 <&rpmcc RPM_SMD_IPA_CLK>;
+			clock-names = "cpu_axi",
+				      "ufs_axi",
+				      "usb_axi",
+				      "ipa";
+			#interconnect-cells = <2>;
+
+			clk_virt: interconnect-clk {
+				compatible = "qcom,sm6115-clk-virt";
+				#interconnect-cells = <2>;
+			};
+
+			mmrt_virt: interconnect-mmrt {
+				compatible = "qcom,sm6115-mmrt-virt";
+				#interconnect-cells = <2>;
+			};
+
+			mmnrt_virt: interconnect-mmnrt {
+				compatible = "qcom,sm6115-mmnrt-virt";
+				#interconnect-cells = <2>;
+			};
+		};
+
+		config_noc: interconnect@1900000 {
+			compatible = "qcom,sm6115-cnoc";
+			reg = <0x0 0x01900000 0x0 0x6200>;
+			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>;
+			clock-names = "usb_axi";
+			#interconnect-cells = <2>;
+		};
+
 		qfprom@1b40000 {
 			compatible = "qcom,sm6115-qfprom", "qcom,qfprom";
 			reg = <0x0 0x01b40000 0x0 0x7000>;
@@ -902,6 +943,60 @@ rng: rng@1b53000 {
 			clock-names = "core";
 		};
 
+		pmu@1b8e300 {
+			compatible = "qcom,sm6115-cpu-bwmon", "qcom,sdm845-bwmon";
+			reg = <0x0 0x01b8e300 0x0 0x600>;
+			interrupts = <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>;
+
+			operating-points-v2 = <&cpu_bwmon_opp_table>;
+			interconnects = <&bimc MASTER_AMPSS_M0 RPM_ACTIVE_TAG
+					 &bimc SLAVE_EBI_CH0 RPM_ACTIVE_TAG>;
+
+			cpu_bwmon_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-0 {
+					opp-peak-kBps = <(200 * 4 * 1000)>;
+				};
+
+				opp-1 {
+					opp-peak-kBps = <(300 * 4 * 1000)>;
+				};
+
+				opp-2 {
+					opp-peak-kBps = <(451 * 4 * 1000)>;
+				};
+
+				opp-3 {
+					opp-peak-kBps = <(547 * 4 * 1000)>;
+				};
+
+				opp-4 {
+					opp-peak-kBps = <(681 * 4 * 1000)>;
+				};
+
+				opp-5 {
+					opp-peak-kBps = <(768 * 4 * 1000)>;
+				};
+
+				opp-6 {
+					opp-peak-kBps = <(1017 * 4 * 1000)>;
+				};
+
+				opp-7 {
+					opp-peak-kBps = <(1353 * 4 * 1000)>;
+				};
+
+				opp-8 {
+					opp-peak-kBps = <(1555 * 4 * 1000)>;
+				};
+
+				opp-9 {
+					opp-peak-kBps = <(1804 * 4 * 1000)>;
+				};
+			};
+		};
+
 		spmi_bus: spmi@1c40000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0x0 0x01c40000 0x0 0x1100>,
@@ -931,6 +1026,12 @@ tsens0: thermal-sensor@4411000 {
 			#thermal-sensor-cells = <1>;
 		};
 
+		bimc: interconnect@4480000 {
+			compatible = "qcom,sm6115-bimc";
+			reg = <0x0 0x04480000 0x0 0x80000>;
+			#interconnect-cells = <2>;
+		};
+
 		rpm_msg_ram: sram@45f0000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0x0 0x045f0000 0x0 0x7000>;
@@ -958,8 +1059,42 @@ sdhc_1: mmc@4744000 {
 				 <&gcc GCC_SDCC1_ICE_CORE_CLK>;
 			clock-names = "iface", "core", "xo", "ice";
 
+			power-domains = <&rpmpd SM6115_VDDCX>;
+			operating-points-v2 = <&sdhc1_opp_table>;
+			interconnects = <&system_noc MASTER_SDCC_1 RPM_ALWAYS_TAG
+					 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>,
+					<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+					 &config_noc SLAVE_SDCC_1 RPM_ALWAYS_TAG>;
+			interconnect-names = "sdhc-ddr",
+					     "cpu-sdhc";
+
 			bus-width = <8>;
 			status = "disabled";
+
+			sdhc1_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmpd_opp_low_svs>;
+					opp-peak-kBps = <250000 133320>;
+					opp-avg-kBps = <102400 65000>;
+				};
+
+				opp-192000000 {
+					opp-hz = /bits/ 64 <192000000>;
+					required-opps = <&rpmpd_opp_low_svs>;
+					opp-peak-kBps = <800000 300000>;
+					opp-avg-kBps = <204800 200000>;
+				};
+
+				opp-384000000 {
+					opp-hz = /bits/ 64 <384000000>;
+					required-opps = <&rpmpd_opp_svs_plus>;
+					opp-peak-kBps = <800000 300000>;
+					opp-avg-kBps = <204800 200000>;
+				};
+			};
 		};
 
 		sdhc_2: mmc@4784000 {
@@ -980,6 +1115,12 @@ sdhc_2: mmc@4784000 {
 			operating-points-v2 = <&sdhc2_opp_table>;
 			iommus = <&apps_smmu 0x00a0 0x0>;
 			resets = <&gcc GCC_SDCC2_BCR>;
+			interconnects = <&system_noc MASTER_SDCC_2 RPM_ALWAYS_TAG
+					 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>,
+					<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+					 &config_noc SLAVE_SDCC_2 RPM_ALWAYS_TAG>;
+			interconnect-names = "sdhc-ddr",
+					     "cpu-sdhc";
 
 			bus-width = <4>;
 			qcom,dll-config = <0x0007642c>;
@@ -992,11 +1133,15 @@ sdhc2_opp_table: opp-table {
 				opp-100000000 {
 					opp-hz = /bits/ 64 <100000000>;
 					required-opps = <&rpmpd_opp_low_svs>;
+					opp-peak-kBps = <250000 133320>;
+					opp-avg-kBps = <261438 150000>;
 				};
 
 				opp-202000000 {
 					opp-hz = /bits/ 64 <202000000>;
 					required-opps = <&rpmpd_opp_nom>;
+					opp-peak-kBps = <800000 300000>;
+					opp-avg-kBps = <261438 300000>;
 				};
 			};
 		};
@@ -1110,6 +1255,15 @@ i2c0: i2c@4a80000 {
 				dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
 				       <&gpi_dma0 1 0 QCOM_GPI_I2C>;
 				dma-names = "tx", "rx";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+						 &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+						<&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+						 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1126,6 +1280,15 @@ spi0: spi@4a80000 {
 				dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
 				       <&gpi_dma0 1 0 QCOM_GPI_SPI>;
 				dma-names = "tx", "rx";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+						 &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+						<&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+						 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1142,6 +1305,12 @@ i2c1: i2c@4a84000 {
 				dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
 				       <&gpi_dma0 1 1 QCOM_GPI_I2C>;
 				dma-names = "tx", "rx";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+						 &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+						<&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+						 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1158,6 +1327,15 @@ spi1: spi@4a84000 {
 				dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
 				       <&gpi_dma0 1 1 QCOM_GPI_SPI>;
 				dma-names = "tx", "rx";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+						 &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+						<&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+						 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1174,6 +1352,15 @@ i2c2: i2c@4a88000 {
 				dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
 				       <&gpi_dma0 1 2 QCOM_GPI_I2C>;
 				dma-names = "tx", "rx";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+						 &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+						<&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+						 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1190,6 +1377,15 @@ spi2: spi@4a88000 {
 				dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
 				       <&gpi_dma0 1 2 QCOM_GPI_SPI>;
 				dma-names = "tx", "rx";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+						 &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+						<&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+						 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1206,6 +1402,15 @@ i2c3: i2c@4a8c000 {
 				dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
 				       <&gpi_dma0 1 3 QCOM_GPI_I2C>;
 				dma-names = "tx", "rx";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+						 &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+						<&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+						 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1222,6 +1427,15 @@ spi3: spi@4a8c000 {
 				dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
 				       <&gpi_dma0 1 3 QCOM_GPI_SPI>;
 				dma-names = "tx", "rx";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+						 &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+						<&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+						 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1235,6 +1449,12 @@ uart3: serial@4a8c000 {
 				clock-names = "se";
 				power-domains = <&rpmpd SM6115_VDDCX>;
 				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+						 &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>;
+				interconnect-names = "qup-core",
+						     "qup-config";
 				status = "disabled";
 			};
 
@@ -1249,6 +1469,15 @@ i2c4: i2c@4a90000 {
 				dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
 				       <&gpi_dma0 1 4 QCOM_GPI_I2C>;
 				dma-names = "tx", "rx";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+						 &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+						<&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+						 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1265,6 +1494,15 @@ spi4: spi@4a90000 {
 				dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
 				       <&gpi_dma0 1 4 QCOM_GPI_SPI>;
 				dma-names = "tx", "rx";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+						 &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+						<&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+						 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1276,6 +1514,12 @@ uart4: serial@4a90000 {
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
 				interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+						 &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>;
+				interconnect-names = "qup-core",
+						     "qup-config";
 				status = "disabled";
 			};
 
@@ -1290,6 +1534,15 @@ i2c5: i2c@4a94000 {
 				dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
 				       <&gpi_dma0 1 5 QCOM_GPI_I2C>;
 				dma-names = "tx", "rx";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+						 &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+						<&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+						 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1306,6 +1559,15 @@ spi5: spi@4a94000 {
 				dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
 				       <&gpi_dma0 1 5 QCOM_GPI_SPI>;
 				dma-names = "tx", "rx";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
+						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
+						<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+						 &config_noc SLAVE_QUP_0 RPM_ALWAYS_TAG>,
+						<&system_noc MASTER_QUP_0 RPM_ALWAYS_TAG
+						 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -1337,6 +1599,14 @@ usb: usb@4ef8800 {
 
 			resets = <&gcc GCC_USB30_PRIM_BCR>;
 			power-domains = <&gcc GCC_USB30_PRIM_GDSC>;
+			 /* TODO: USB<->IPA path */
+			interconnects = <&system_noc MASTER_USB3 RPM_ALWAYS_TAG
+					 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>,
+					<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+					 &config_noc SLAVE_USB3 RPM_ALWAYS_TAG>;
+			interconnect-names = "usb-ddr",
+					     "apps-usb";
+
 			qcom,select-utmi-as-pipe-clk;
 			status = "disabled";
 
@@ -1508,6 +1778,13 @@ mdss: display-subsystem@5e00000 {
 			iommus = <&apps_smmu 0x420 0x2>,
 				 <&apps_smmu 0x421 0x0>;
 
+			interconnects = <&mmrt_virt MASTER_MDP_PORT0 RPM_ALWAYS_TAG
+					 &bimc SLAVE_EBI_CH0 RPM_ALWAYS_TAG>,
+					<&bimc MASTER_AMPSS_M0 RPM_ALWAYS_TAG
+					 &config_noc SLAVE_DISPLAY_CFG RPM_ALWAYS_TAG>;
+			interconnect-names = "mdp0-mem",
+					     "cpu-cfg";
+
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
