diff mbox series

[v5,08/18] arm64: dts: qcom: sm8650-qrd: add the Wifi node

Message ID 20240216203215.40870-9-brgl@bgdev.pl (mailing list archive)
State Handled Elsewhere, archived
Headers show
Series power: sequencing: implement the subsystem and add first users | expand

Commit Message

Bartosz Golaszewski Feb. 16, 2024, 8:32 p.m. UTC
From: Neil Armstrong <neil.armstrong@linaro.org>

Describe the ath12k WLAN on-board the WCN7850 module present on the
board.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
[Bartosz:
  - move the pcieport0 node into the .dtsi
  - make regulator naming consistent with existing DT code
  - add commit message]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8650-qrd.dts | 29 +++++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sm8650.dtsi    | 10 +++++++++
 2 files changed, 39 insertions(+)

Comments

Dmitry Baryshkov Feb. 16, 2024, 11:09 p.m. UTC | #1
On Fri, 16 Feb 2024 at 22:33, Bartosz Golaszewski <brgl@bgdev.pl> wrote:
>
> From: Neil Armstrong <neil.armstrong@linaro.org>
>
> Describe the ath12k WLAN on-board the WCN7850 module present on the
> board.

WCN7850 is the same combo WiFi + BT chip. Is there any reason for
describing its parts separately rather than using the same PMU
approach?

>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> [Bartosz:
>   - move the pcieport0 node into the .dtsi
>   - make regulator naming consistent with existing DT code
>   - add commit message]
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8650-qrd.dts | 29 +++++++++++++++++++++++++
>  arch/arm64/boot/dts/qcom/sm8650.dtsi    | 10 +++++++++
>  2 files changed, 39 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8650-qrd.dts b/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
> index b07cac2e5bc8..4623c358f634 100644
> --- a/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
> @@ -845,6 +845,28 @@ &pcie0 {
>         status = "okay";
>  };
>
> +&pcieport0 {
> +       wifi@0 {
> +               compatible = "pci17cb,1107";
> +               reg = <0x10000 0x0 0x0 0x0 0x0>;
> +
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&wlan_en>;
> +
> +               enable-gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>;
> +
> +               vdd-supply = <&vreg_s4i_0p85>;
> +               vddio-supply = <&vreg_l15b_1p8>;
> +               vddio1p2-supply = <&vreg_l3c_1p2>;
> +               vddaon-supply = <&vreg_s2c_0p8>;
> +               vdddig-supply = <&vreg_s3c_0p9>;
> +               vddrfa1p2-supply = <&vreg_s1c_1p2>;
> +               vddrfa1p8-supply = <&vreg_s6c_1p8>;
> +
> +               clocks = <&rpmhcc RPMH_RF_CLK1>;
> +       };
> +};
> +
>  &pcie0_phy {
>         vdda-phy-supply = <&vreg_l1i_0p88>;
>         vdda-pll-supply = <&vreg_l3i_1p2>;
> @@ -1139,6 +1161,13 @@ wcd_default: wcd-reset-n-active-state {
>                 bias-disable;
>                 output-low;
>         };
> +
> +       wlan_en: wlan-en-state {
> +               pins = "gpio16";
> +               function = "gpio";
> +               drive-strength = <8>;
> +               bias-pull-down;
> +       };
>  };
>
>  &uart14 {
> diff --git a/arch/arm64/boot/dts/qcom/sm8650.dtsi b/arch/arm64/boot/dts/qcom/sm8650.dtsi
> index d488b3b3265e..baf4932e460c 100644
> --- a/arch/arm64/boot/dts/qcom/sm8650.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8650.dtsi
> @@ -2293,6 +2293,16 @@ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
>                         dma-coherent;
>
>                         status = "disabled";
> +
> +                       pcieport0: pcie@0 {
> +                               device_type = "pci";
> +                               reg = <0x0 0x0 0x0 0x0 0x0>;
> +                               #address-cells = <3>;
> +                               #size-cells = <2>;
> +                               ranges;
> +
> +                               bus-range = <0x01 0xff>;
> +                       };
>                 };
>
>                 pcie0_phy: phy@1c06000 {
> --
> 2.40.1
>
Bartosz Golaszewski Feb. 17, 2024, 6:53 p.m. UTC | #2
On Sat, Feb 17, 2024 at 12:10 AM Dmitry Baryshkov
<dmitry.baryshkov@linaro.org> wrote:
>
> On Fri, 16 Feb 2024 at 22:33, Bartosz Golaszewski <brgl@bgdev.pl> wrote:
> >
> > From: Neil Armstrong <neil.armstrong@linaro.org>
> >
> > Describe the ath12k WLAN on-board the WCN7850 module present on the
> > board.
>
> WCN7850 is the same combo WiFi + BT chip. Is there any reason for
> describing its parts separately rather than using the same PMU
> approach?
>

Yes, I explained the rationale in the cover letter in detail in the
section describing the DTS changes for the series.

Bart

[snip]
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sm8650-qrd.dts b/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
index b07cac2e5bc8..4623c358f634 100644
--- a/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
@@ -845,6 +845,28 @@  &pcie0 {
 	status = "okay";
 };
 
+&pcieport0 {
+	wifi@0 {
+		compatible = "pci17cb,1107";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_en>;
+
+		enable-gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&vreg_s4i_0p85>;
+		vddio-supply = <&vreg_l15b_1p8>;
+		vddio1p2-supply = <&vreg_l3c_1p2>;
+		vddaon-supply = <&vreg_s2c_0p8>;
+		vdddig-supply = <&vreg_s3c_0p9>;
+		vddrfa1p2-supply = <&vreg_s1c_1p2>;
+		vddrfa1p8-supply = <&vreg_s6c_1p8>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK1>;
+	};
+};
+
 &pcie0_phy {
 	vdda-phy-supply = <&vreg_l1i_0p88>;
 	vdda-pll-supply = <&vreg_l3i_1p2>;
@@ -1139,6 +1161,13 @@  wcd_default: wcd-reset-n-active-state {
 		bias-disable;
 		output-low;
 	};
+
+	wlan_en: wlan-en-state {
+		pins = "gpio16";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-down;
+	};
 };
 
 &uart14 {
diff --git a/arch/arm64/boot/dts/qcom/sm8650.dtsi b/arch/arm64/boot/dts/qcom/sm8650.dtsi
index d488b3b3265e..baf4932e460c 100644
--- a/arch/arm64/boot/dts/qcom/sm8650.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8650.dtsi
@@ -2293,6 +2293,16 @@  &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
 			dma-coherent;
 
 			status = "disabled";
+
+			pcieport0: pcie@0 {
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+
+				bus-range = <0x01 0xff>;
+			};
 		};
 
 		pcie0_phy: phy@1c06000 {