| Message ID | 20250214-mt6359-accdet-dts-v1-1-677a151b9b4c@collabora.com (mailing list archive) |
|---|---|
| State | Handled Elsewhere, archived |
| Headers | show |
| Series | Get mt6359-accdet ready for usage in Devicetree | expand |
Il 14/02/25 18:18, Nícolas F. R. A. Prado ha scritto: > Add dt-binding for the MT6359 ACCDET hardware block. > > Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> > --- > .../bindings/sound/mediatek,mt6359-accdet.yaml | 293 +++++++++++++++++++++ > 1 file changed, 293 insertions(+) > > diff --git a/Documentation/devicetree/bindings/sound/mediatek,mt6359-accdet.yaml b/Documentation/devicetree/bindings/sound/mediatek,mt6359-accdet.yaml > new file mode 100644 > index 0000000000000000000000000000000000000000..8922003d3b9d039d2a0355add7a90cf42b1a9da6 > --- /dev/null > +++ b/Documentation/devicetree/bindings/sound/mediatek,mt6359-accdet.yaml > @@ -0,0 +1,293 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/sound/mediatek,mt6359-accdet.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: MT6359 Accessory Detection > + > +maintainers: > + - Nícolas F. R. A. Prado <nfraprado@collabora.com> > + > +description: | > + The MT6359 Accessory Detection block is part of the MT6359 PMIC and allows > + detecting audio jack insertion and removal, as well as identifying the type of > + events connected to the jack. > + > +properties: > + compatible: > + const: mediatek,mt6359-accdet > + > + mediatek,mic-vol: mediatek,micbias1-microvolts = <1700000>; enum: [1700000, 1800000 ... etc ] > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: MIC bias1 output voltage setting > + enum: > + - 0 # 1.7V > + - 1 # 1.8V > + - 2 # 1.9V > + - 3 # 2.0V > + - 4 # 2.1V > + - 5 # 2.5V > + - 6 # 2.6V > + - 7 # 2.7V > + - 8 # 2.8V > + - 9 # 2.85V > + > + mediatek,mic-mode: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Mic mode setting > + enum: > + - 1 # ACC > + - 2 # DCC mode. Low cost mode without internal bias > + - 6 # DCC mode. Low cost mode with internal bias This is already defined in mt6359.yaml....?! > + > + mediatek,eint-cmpmen-pwm-width: mediatek,eint-cmpm-pwm-width-ms: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: EINT CMPMEN PWM width P.S.: CMPMEN = CoMParator Monitor ENable description: EINT Comparator Monitor PWM Width enum: [50, 80, 100, 200, 400, 500, 800, 1000] > + enum: > + - 0 # 50ms > + - 1 # 80ms > + - 2 # 100ms > + - 3 # 200ms > + - 4 # 400ms > + - 5 # 500ms > + - 6 # 800ms > + - 7 # 1000ms > + > + mediatek,eint-cmpmen-pwm-thresh: mediatek,eint-cmpm-pwm-threshold-ms: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: EINT CMPMEN PWM threshold description: EINT Comparator Monitor PWM Threshold enum: [1, 2, 3, 4, 5, 8, 10, 20, 30] > + enum: > + - 0 # 1ms > + - 1 # 2ms > + - 2 # 4ms > + - 3 # 5ms > + - 4 # 8ms > + - 5 # 10ms > + - 6 # 20ms > + - 7 # 30ms > + > + mediatek,pwm-width: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: PWM width > + minimum: 0 > + maximum: 65535 > + > + mediatek,pwm-thresh: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: PWM threshold > + minimum: 0 > + maximum: 65535 You can simplify those two with one param "mediatek,pwm-duty-cycle", I think. But then, regardless, you still need to express this in decent units... make a few calculations - but the equation is... PWM Width = (32768 / (mediatek,pwm-width + 1)) [hertz] PWM Duty Cycle = ((mediatek,pwm-thresh + 1) / (mediatek,pwm-width + 1)) [ns?] PWM High Time = (mediatek,pwm-thresh + 1) / 32768 [seconds] > + > + mediatek,pwm-rise-delay: mediatek,pwm-rise-delay-cycle: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Rise delay for PWM description: Rising delay of PWM waveform in cycles > + minimum: 0 > + maximum: 65535 > + > + mediatek,pwm-fall-delay: same for the falling one > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Fall delay for PWM > + minimum: 0 > + maximum: 65535 > + > + mediatek,debounce0: mediatek,adc-debounce-ns = < debounce0 debounce1 debounce2 debounce3 > > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Debounce time for state 0 > + minimum: 0 > + maximum: 65535 > + > + mediatek,debounce1: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Debounce time for state 1 > + minimum: 0 > + maximum: 65535 > + > + mediatek,debounce3: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Debounce time for state 3 > + minimum: 0 > + maximum: 65535 > + > + mediatek,debounce-auxadc: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Debounce time for AUXADC > + minimum: 0 > + maximum: 65535 > + mediatek,eint-debounce-ns = < same as adc-debounce-ns > > + mediatek,eint-debounce0: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Debounce time for EINT state 0 > + enum: > + - 0 # 0ms > + - 1 # 0.12ms > + - 2 # 0.25ms > + - 3 # 0.5ms > + - 4 # 0.75ms > + - 5 # 1ms > + - 6 # 2ms > + - 7 # 4ms > + - 8 # 8ms > + - 9 # 16ms > + - 10 # 32ms > + - 11 # 48ms > + - 12 # 64ms > + - 13 # 128ms > + - 14 # 256ms > + - 15 # 512ms > + > + mediatek,eint-debounce1: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Debounce time for EINT state 1 > + enum: > + - 0 # 0ms > + - 1 # 0.5ms > + - 2 # 0.75ms > + - 3 # 0.9ms > + - 4 # 1.5ms > + - 5 # 1.8ms > + - 6 # 3ms > + - 7 # 3.5ms > + - 8 # 3.8ms > + - 9 # 16ms > + - 10 # 32ms > + - 11 # 48ms > + - 12 # 64ms > + - 13 # 128ms > + - 14 # 256ms > + - 15 # 512ms > + > + mediatek,eint-debounce2: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Debounce time for EINT state 2 > + enum: > + - 0 # 0ms > + - 1 # 0.5ms > + - 2 # 0.75ms > + - 3 # 0.9ms > + - 4 # 1.5ms > + - 5 # 1.8ms > + - 6 # 3ms > + - 7 # 3.5ms > + - 8 # 3.8ms > + - 9 # 4ms > + - 10 # 4.5ms > + - 11 # 5ms > + - 12 # 7ms > + - 13 # 9ms > + - 14 # 19ms > + - 15 # 25ms > + > + mediatek,eint-debounce3: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Debounce time for EINT state 3 > + enum: > + - 0 # 0ms > + - 1 # 0.12ms > + - 2 # 0.25ms > + - 3 # 0.5ms > + - 4 # 0.75ms > + - 5 # 1ms > + - 6 # 2ms > + - 7 # 4ms > + - 8 # 8ms > + - 9 # 16ms > + - 10 # 32ms > + - 11 # 48ms > + - 12 # 64ms > + - 13 # 128ms > + - 14 # 256ms > + - 15 # 512ms > + > + mediatek,eint-inverter-debounce: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: Debounce time for EINT inverter > + enum: > + - 0 # 0ms > + - 1 # 0.12ms > + - 2 # 0.25ms > + - 3 # 0.5ms > + - 4 # 0.75ms > + - 5 # 1ms > + - 6 # 2ms > + - 7 # 4ms > + - 8 # 8ms > + - 9 # 16ms > + - 10 # 32ms > + - 11 # 48ms > + - 12 # 64ms > + - 13 # 128ms > + - 14 # 256ms > + - 15 # 512ms > + > + mediatek,eint-detect-mode: This is fine, I think. > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: EINT detection mode > + enum: > + - 0 # Higher detection power > + - 1 # Lower detection power > + - 2 # SW moisture detection mode1 > + - 3 # HW moisture detection mode1 > + - 4 # HW moisture detection mode2 > + > + mediatek,eint-num: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: EINT interrupt that should be enabled > + enum: > + - 0 # EINT0 > + - 1 # EINT1 > + - 2 # EINT0 | EINT1 > + > + mediatek,eint-use-ext-res: > + type: boolean > + description: > + Whether an external resistor should be used for the HP_EINT signal. > + By default an internal pull-up resistor is used. > + > + mediatek,eint-comp-vth: mediatek,eint-comp-vth-microvolts = .... > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: EINT comparator threshold > + enum: > + - 0 # 2.4V > + - 1 # 2V > + - 2 # 1.6V > + - 3 # 1.2V > + - 4 # 0.8V > + ...and that's more or less it.... Cheers, Angelo > + mediatek,eint-level-pol: > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: EINT interrupt polarity > + > +required: > + - compatible > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/irq.h> > + > + accdet: accdet { > + compatible = "mediatek,mt6359-accdet"; > + mediatek,mic-vol = <8>; > + mediatek,mic-mode = <2>; > + mediatek,pwm-width = <0x500>; > + mediatek,pwm-thresh = <0x500>; > + mediatek,pwm-fall-delay = <1>; > + mediatek,pwm-rise-delay = <0x1f0>; > + mediatek,debounce0 = <0x800>; > + mediatek,debounce1 = <0x800>; > + mediatek,debounce3 = <0x20>; > + mediatek,debounce-auxadc = <0x44>; > + mediatek,eint-cmpmen-pwm-width = <4>; > + mediatek,eint-cmpmen-pwm-thresh = <1>; > + mediatek,eint-debounce0 = <5>; > + mediatek,eint-debounce1 = <3>; > + mediatek,eint-debounce2 = <3>; > + mediatek,eint-debounce3 = <5>; > + mediatek,eint-inverter-debounce = <0xe>; > + mediatek,eint-detect-mode = <4>; > + mediatek,eint-num = <0>; > + mediatek,eint-comp-vth = <2>; > + mediatek,eint-level-pol = <IRQ_TYPE_LEVEL_LOW>; > + }; >
diff --git a/Documentation/devicetree/bindings/sound/mediatek,mt6359-accdet.yaml b/Documentation/devicetree/bindings/sound/mediatek,mt6359-accdet.yaml new file mode 100644 index 0000000000000000000000000000000000000000..8922003d3b9d039d2a0355add7a90cf42b1a9da6 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mediatek,mt6359-accdet.yaml @@ -0,0 +1,293 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/mediatek,mt6359-accdet.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MT6359 Accessory Detection + +maintainers: + - Nícolas F. R. A. Prado <nfraprado@collabora.com> + +description: | + The MT6359 Accessory Detection block is part of the MT6359 PMIC and allows + detecting audio jack insertion and removal, as well as identifying the type of + events connected to the jack. + +properties: + compatible: + const: mediatek,mt6359-accdet + + mediatek,mic-vol: + $ref: /schemas/types.yaml#/definitions/uint32 + description: MIC bias1 output voltage setting + enum: + - 0 # 1.7V + - 1 # 1.8V + - 2 # 1.9V + - 3 # 2.0V + - 4 # 2.1V + - 5 # 2.5V + - 6 # 2.6V + - 7 # 2.7V + - 8 # 2.8V + - 9 # 2.85V + + mediatek,mic-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Mic mode setting + enum: + - 1 # ACC + - 2 # DCC mode. Low cost mode without internal bias + - 6 # DCC mode. Low cost mode with internal bias + + mediatek,eint-cmpmen-pwm-width: + $ref: /schemas/types.yaml#/definitions/uint32 + description: EINT CMPMEN PWM width + enum: + - 0 # 50ms + - 1 # 80ms + - 2 # 100ms + - 3 # 200ms + - 4 # 400ms + - 5 # 500ms + - 6 # 800ms + - 7 # 1000ms + + mediatek,eint-cmpmen-pwm-thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + description: EINT CMPMEN PWM threshold + enum: + - 0 # 1ms + - 1 # 2ms + - 2 # 4ms + - 3 # 5ms + - 4 # 8ms + - 5 # 10ms + - 6 # 20ms + - 7 # 30ms + + mediatek,pwm-width: + $ref: /schemas/types.yaml#/definitions/uint32 + description: PWM width + minimum: 0 + maximum: 65535 + + mediatek,pwm-thresh: + $ref: /schemas/types.yaml#/definitions/uint32 + description: PWM threshold + minimum: 0 + maximum: 65535 + + mediatek,pwm-rise-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Rise delay for PWM + minimum: 0 + maximum: 65535 + + mediatek,pwm-fall-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Fall delay for PWM + minimum: 0 + maximum: 65535 + + mediatek,debounce0: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Debounce time for state 0 + minimum: 0 + maximum: 65535 + + mediatek,debounce1: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Debounce time for state 1 + minimum: 0 + maximum: 65535 + + mediatek,debounce3: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Debounce time for state 3 + minimum: 0 + maximum: 65535 + + mediatek,debounce-auxadc: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Debounce time for AUXADC + minimum: 0 + maximum: 65535 + + mediatek,eint-debounce0: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Debounce time for EINT state 0 + enum: + - 0 # 0ms + - 1 # 0.12ms + - 2 # 0.25ms + - 3 # 0.5ms + - 4 # 0.75ms + - 5 # 1ms + - 6 # 2ms + - 7 # 4ms + - 8 # 8ms + - 9 # 16ms + - 10 # 32ms + - 11 # 48ms + - 12 # 64ms + - 13 # 128ms + - 14 # 256ms + - 15 # 512ms + + mediatek,eint-debounce1: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Debounce time for EINT state 1 + enum: + - 0 # 0ms + - 1 # 0.5ms + - 2 # 0.75ms + - 3 # 0.9ms + - 4 # 1.5ms + - 5 # 1.8ms + - 6 # 3ms + - 7 # 3.5ms + - 8 # 3.8ms + - 9 # 16ms + - 10 # 32ms + - 11 # 48ms + - 12 # 64ms + - 13 # 128ms + - 14 # 256ms + - 15 # 512ms + + mediatek,eint-debounce2: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Debounce time for EINT state 2 + enum: + - 0 # 0ms + - 1 # 0.5ms + - 2 # 0.75ms + - 3 # 0.9ms + - 4 # 1.5ms + - 5 # 1.8ms + - 6 # 3ms + - 7 # 3.5ms + - 8 # 3.8ms + - 9 # 4ms + - 10 # 4.5ms + - 11 # 5ms + - 12 # 7ms + - 13 # 9ms + - 14 # 19ms + - 15 # 25ms + + mediatek,eint-debounce3: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Debounce time for EINT state 3 + enum: + - 0 # 0ms + - 1 # 0.12ms + - 2 # 0.25ms + - 3 # 0.5ms + - 4 # 0.75ms + - 5 # 1ms + - 6 # 2ms + - 7 # 4ms + - 8 # 8ms + - 9 # 16ms + - 10 # 32ms + - 11 # 48ms + - 12 # 64ms + - 13 # 128ms + - 14 # 256ms + - 15 # 512ms + + mediatek,eint-inverter-debounce: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Debounce time for EINT inverter + enum: + - 0 # 0ms + - 1 # 0.12ms + - 2 # 0.25ms + - 3 # 0.5ms + - 4 # 0.75ms + - 5 # 1ms + - 6 # 2ms + - 7 # 4ms + - 8 # 8ms + - 9 # 16ms + - 10 # 32ms + - 11 # 48ms + - 12 # 64ms + - 13 # 128ms + - 14 # 256ms + - 15 # 512ms + + mediatek,eint-detect-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + description: EINT detection mode + enum: + - 0 # Higher detection power + - 1 # Lower detection power + - 2 # SW moisture detection mode1 + - 3 # HW moisture detection mode1 + - 4 # HW moisture detection mode2 + + mediatek,eint-num: + $ref: /schemas/types.yaml#/definitions/uint32 + description: EINT interrupt that should be enabled + enum: + - 0 # EINT0 + - 1 # EINT1 + - 2 # EINT0 | EINT1 + + mediatek,eint-use-ext-res: + type: boolean + description: + Whether an external resistor should be used for the HP_EINT signal. + By default an internal pull-up resistor is used. + + mediatek,eint-comp-vth: + $ref: /schemas/types.yaml#/definitions/uint32 + description: EINT comparator threshold + enum: + - 0 # 2.4V + - 1 # 2V + - 2 # 1.6V + - 3 # 1.2V + - 4 # 0.8V + + mediatek,eint-level-pol: + $ref: /schemas/types.yaml#/definitions/uint32 + description: EINT interrupt polarity + +required: + - compatible + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + accdet: accdet { + compatible = "mediatek,mt6359-accdet"; + mediatek,mic-vol = <8>; + mediatek,mic-mode = <2>; + mediatek,pwm-width = <0x500>; + mediatek,pwm-thresh = <0x500>; + mediatek,pwm-fall-delay = <1>; + mediatek,pwm-rise-delay = <0x1f0>; + mediatek,debounce0 = <0x800>; + mediatek,debounce1 = <0x800>; + mediatek,debounce3 = <0x20>; + mediatek,debounce-auxadc = <0x44>; + mediatek,eint-cmpmen-pwm-width = <4>; + mediatek,eint-cmpmen-pwm-thresh = <1>; + mediatek,eint-debounce0 = <5>; + mediatek,eint-debounce1 = <3>; + mediatek,eint-debounce2 = <3>; + mediatek,eint-debounce3 = <5>; + mediatek,eint-inverter-debounce = <0xe>; + mediatek,eint-detect-mode = <4>; + mediatek,eint-num = <0>; + mediatek,eint-comp-vth = <2>; + mediatek,eint-level-pol = <IRQ_TYPE_LEVEL_LOW>; + };
Add dt-binding for the MT6359 ACCDET hardware block. Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> --- .../bindings/sound/mediatek,mt6359-accdet.yaml | 293 +++++++++++++++++++++ 1 file changed, 293 insertions(+)