diff --git a/drivers/infiniband/hw/qib/qib.h b/drivers/infiniband/hw/qib/qib.h
new file mode 100644
index 0000000..d715eeb
--- /dev/null
+++ b/drivers/infiniband/hw/qib/qib.h
@@ -0,0 +1,1437 @@
+#ifndef _QIB_KERNEL_H
+#define _QIB_KERNEL_H
+/*
+ * Copyright (c) 2006, 2007, 2008, 2009 QLogic Corporation. All rights reserved.
+ * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
+ *
+ * This software is available to you under a choice of one of two
+ * licenses.  You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the
+ * OpenIB.org BSD license below:
+ *
+ *     Redistribution and use in source and binary forms, with or
+ *     without modification, are permitted provided that the following
+ *     conditions are met:
+ *
+ *      - Redistributions of source code must retain the above
+ *        copyright notice, this list of conditions and the following
+ *        disclaimer.
+ *
+ *      - Redistributions in binary form must reproduce the above
+ *        copyright notice, this list of conditions and the following
+ *        disclaimer in the documentation and/or other materials
+ *        provided with the distribution.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
+ * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
+ * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+ * SOFTWARE.
+ */
+
+/*
+ * This header file is the base header file for qlogic_ib kernel code
+ * qib_user.h serves a similar purpose for user code.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/dma-mapping.h>
+#include <linux/mutex.h>
+#include <linux/list.h>
+#include <linux/scatterlist.h>
+#include <linux/io.h>
+#include <linux/fs.h>
+#include <linux/completion.h>
+#include <linux/kref.h>
+#include <linux/sched.h>
+
+#include "qib_common.h"
+#include "qib_debug.h"
+#include "qib_verbs.h"
+
+/* only s/w major version of QLogic_IB we can handle */
+#define QIB_CHIP_VERS_MAJ 2U
+
+/* don't care about this except printing */
+#define QIB_CHIP_VERS_MIN 0U
+
+/* The Organization Unique Identifier (Mfg code), and its position in GUID */
+#define QIB_OUI 0x001175
+#define QIB_OUI_LSB 40
+
+/*
+ * per driver stats, either not device nor port-specific, or
+ * summed over all of the devices and ports.
+ * They are described by name via ipathfs filesystem, so layout
+ * and number of elements can change without breaking compatibility.
+ * If members are added or deleted qib_statnames[] in qib_fs.c must
+ * change to match.
+ */
+struct qlogic_ib_stats {
+	__u64 sps_ints; /* number of interrupts handled */
+	__u64 sps_errints; /* number of error interrupts */
+	__u64 sps_txerrs; /* tx-related packet errors */
+	__u64 sps_rcverrs; /* non-crc rcv packet errors */
+	__u64 sps_hwerrs; /* hardware errors reported (parity, etc.) */
+	__u64 sps_nopiobufs; /* no pio bufs avail from kernel */
+	__u64 sps_ctxts; /* number of contexts currently open */
+	__u64 sps_lenerrs; /* number of kernel packets where RHF != LRH len */
+	__u64 sps_buffull;
+	__u64 sps_hdrfull;
+};
+
+extern struct qlogic_ib_stats qib_stats;
+extern struct pci_error_handlers qib_pci_err_handler;
+extern struct pci_driver qib_driver;
+
+#define QIB_CHIP_SWVERSION QIB_CHIP_VERS_MAJ
+/*
+ * First-cut critierion for "device is active" is
+ * two thousand dwords combined Tx, Rx traffic per
+ * 5-second interval. SMA packets are 64 dwords,
+ * and occur "a few per second", presumably each way.
+ */
+#define QIB_TRAFFIC_ACTIVE_THRESHOLD (2000)
+
+/*
+ * Struct used to indicate which errors are logged in each of the
+ * error-counters that are logged to EEPROM. A counter is incremented
+ * _once_ (saturating at 255) for each event with any bits set in
+ * the error or hwerror register masks below.
+ */
+#define QIB_EEP_LOG_CNT (4)
+struct qib_eep_log_mask {
+	u64 errs_to_log;
+	u64 hwerrs_to_log;
+};
+
+/*
+ * Below contains all data related to a single context (formerly called port).
+ */
+struct qib_ctxtdata {
+	void **rcvegrbuf;
+	dma_addr_t *rcvegrbuf_phys;
+	/* rcvhdrq base, needs mmap before useful */
+	void *rcvhdrq;
+	/* kernel virtual address where hdrqtail is updated */
+	void *rcvhdrtail_kvaddr;
+	/*
+	 * temp buffer for expected send setup, allocated at open, instead
+	 * of each setup call
+	 */
+	void *tid_pg_list;
+	/*
+	 * Shared page for kernel to signal user processes that send buffers
+	 * need disarming.  The process should call QIB_CMD_DISARM_BUFS
+	 * or QIB_CMD_ACK_EVENT with IPATH_EVENT_DISARM_BUFS set.
+	 */
+	unsigned long *user_event_mask;
+	/* when waiting for rcv or pioavail */
+	wait_queue_head_t wait;
+	/*
+	 * rcvegr bufs base, physical, must fit
+	 * in 44 bits so 32 bit programs mmap64 44 bit works)
+	 */
+	dma_addr_t rcvegr_phys;
+	/* mmap of hdrq, must fit in 44 bits */
+	dma_addr_t rcvhdrq_phys;
+	dma_addr_t rcvhdrqtailaddr_phys;
+
+	/*
+	 * number of opens (including slave sub-contexts) on this instance
+	 * (ignoring forks, dup, etc. for now)
+	 */
+	int cnt;
+	/*
+	 * how much space to leave at start of eager TID entries for
+	 * protocol use, on each TID
+	 */
+	/* instead of calculating it */
+	unsigned ctxt;
+	/* non-zero if ctxt is being shared. */
+	u16 subctxt_cnt;
+	/* non-zero if ctxt is being shared. */
+	u16 subctxt_id;
+	/* number of eager TID entries. */
+	u16 rcvegrcnt;
+	/* index of first eager TID entry. */
+	u16 rcvegr_tid_base;
+	/* number of pio bufs for this ctxt (all procs, if shared) */
+	u32 piocnt;
+	/* first pio buffer for this ctxt */
+	u32 pio_base;
+	/* chip offset of PIO buffers for this ctxt */
+	u32 piobufs;
+	/* how many alloc_pages() chunks in rcvegrbuf_pages */
+	u32 rcvegrbuf_chunks;
+	/* how many egrbufs per chunk */
+	u32 rcvegrbufs_perchunk;
+	/* order for rcvegrbuf_pages */
+	size_t rcvegrbuf_size;
+	/* rcvhdrq size (for freeing) */
+	size_t rcvhdrq_size;
+	/* per-context flags for fileops/intr communication */
+	unsigned long flag;
+	/* next expected TID to check when looking for free */
+	u32 tidcursor;
+	/* WAIT_RCV that timed out, no interrupt */
+	u32 rcvwait_to;
+	/* WAIT_PIO that timed out, no interrupt */
+	u32 piowait_to;
+	/* WAIT_RCV already happened, no wait */
+	u32 rcvnowait;
+	/* WAIT_PIO already happened, no wait */
+	u32 pionowait;
+	/* total number of polled urgent packets */
+	u32 urgent;
+	/* saved total number of polled urgent packets for poll edge trigger */
+	u32 urgent_poll;
+	/* pid of process using this ctxt */
+	pid_t pid;
+	pid_t subpid[QLOGIC_IB_MAX_SUBCTXT];
+	/* same size as task_struct .comm[], command that opened context */
+	char comm[16];
+	/* pkeys set by this use of this ctxt */
+	u16 pkeys[4];
+	/* so file ops can get at unit */
+	struct qib_devdata *dd;
+	/* so funcs that need physical port can get it easily */
+	struct qib_pportdata *ppd;
+	/* A page of memory for rcvhdrhead, rcvegrhead, rcvegrtail * N */
+	void *subctxt_uregbase;
+	/* An array of pages for the eager receive buffers * N */
+	void *subctxt_rcvegrbuf;
+	/* An array of pages for the eager header queue entries * N */
+	void *subctxt_rcvhdr_base;
+	/* The version of the library which opened this ctxt */
+	u32 userversion;
+	/* Bitmask of active slaves */
+	u32 active_slaves;
+	/* Type of packets or conditions we want to poll for */
+	u16 poll_type;
+	/* receive packet sequence counter */
+	u8 seq_cnt;
+	u8 redirect_seq_cnt;
+	/* ctxt rcvhdrq head offset */
+	u32 head;
+	u32 pkt_count;
+	/* QPs waiting for context processing */
+	struct list_head qp_wait_list;
+};
+
+struct qib_sge_state;
+
+struct qib_sdma_txreq {
+	int                 flags;
+	int                 sg_count;
+	dma_addr_t          addr;
+	void              (*callback)(struct qib_sdma_txreq *, int);
+	u16                 start_idx;  /* sdma private */
+	u16                 next_descq_idx;  /* sdma private */
+	struct list_head    list;       /* sdma private */
+};
+
+struct qib_sdma_desc {
+	__le64 qw[2];
+};
+
+struct qib_verbs_txreq {
+	struct qib_sdma_txreq   txreq;
+	struct qib_qp           *qp;
+	struct qib_swqe         *wqe;
+	u32                     dwords;
+	u16                     hdr_dwords;
+	u16                     hdr_inx;
+	struct qib_pio_header	*align_buf;
+	struct qib_mregion	*mr;
+	struct qib_sge_state    *ss;
+};
+
+#define QIB_SDMA_TXREQ_F_USELARGEBUF  0x1
+#define QIB_SDMA_TXREQ_F_HEADTOHOST   0x2
+#define QIB_SDMA_TXREQ_F_INTREQ       0x4
+#define QIB_SDMA_TXREQ_F_FREEBUF      0x8
+#define QIB_SDMA_TXREQ_F_FREEDESC     0x10
+
+#define QIB_SDMA_TXREQ_S_OK        0
+#define QIB_SDMA_TXREQ_S_SENDERROR 1
+#define QIB_SDMA_TXREQ_S_ABORTED   2
+#define QIB_SDMA_TXREQ_S_SHUTDOWN  3
+
+/*
+ * Get/Set IB link-level config parameters for f_get/set_ib_cfg()
+ * Mostly for MADs that set or query link parameters, also ipath
+ * config interfaces
+ */
+#define QIB_IB_CFG_LIDLMC 0 /* LID (LS16b) and Mask (MS16b) */
+#define QIB_IB_CFG_LWID_ENB 2 /* allowed Link-width */
+#define QIB_IB_CFG_LWID 3 /* currently active Link-width */
+#define QIB_IB_CFG_SPD_ENB 4 /* allowed Link speeds */
+#define QIB_IB_CFG_SPD 5 /* current Link spd */
+#define QIB_IB_CFG_RXPOL_ENB 6 /* Auto-RX-polarity enable */
+#define QIB_IB_CFG_LREV_ENB 7 /* Auto-Lane-reversal enable */
+#define QIB_IB_CFG_LINKLATENCY 8 /* Link Latency (IB1.2 only) */
+#define QIB_IB_CFG_HRTBT 9 /* IB heartbeat off/enable/auto; DDR/QDR only */
+#define QIB_IB_CFG_OP_VLS 10 /* operational VLs */
+#define QIB_IB_CFG_VL_HIGH_CAP 11 /* num of VL high priority weights */
+#define QIB_IB_CFG_VL_LOW_CAP 12 /* num of VL low priority weights */
+#define QIB_IB_CFG_OVERRUN_THRESH 13 /* IB overrun threshold */
+#define QIB_IB_CFG_PHYERR_THRESH 14 /* IB PHY error threshold */
+#define QIB_IB_CFG_LINKDEFAULT 15 /* IB link default (sleep/poll) */
+#define QIB_IB_CFG_PKEYS 16 /* update partition keys */
+#define QIB_IB_CFG_MTU 17 /* update MTU in IBC */
+#define QIB_IB_CFG_LSTATE 18 /* update linkcmd and linkinitcmd in IBC */
+#define QIB_IB_CFG_VL_HIGH_LIMIT 19
+#define QIB_IB_CFG_PMA_TICKS 20 /* PMA sample tick resolution */
+#define QIB_IB_CFG_PORT 21 /* switch port we are connected to */
+
+/*
+ * for CFG_LSTATE: LINKCMD in upper 16 bits, LINKINITCMD in lower 16
+ * IB_LINKINITCMD_POLL and SLEEP are also used as set/get values for
+ * QIB_IB_CFG_LINKDEFAULT cmd
+ */
+#define   IB_LINKCMD_DOWN   (0 << 16)
+#define   IB_LINKCMD_ARMED  (1 << 16)
+#define   IB_LINKCMD_ACTIVE (2 << 16)
+#define   IB_LINKINITCMD_NOP     0
+#define   IB_LINKINITCMD_POLL    1
+#define   IB_LINKINITCMD_SLEEP   2
+#define   IB_LINKINITCMD_DISABLE 3
+
+/*
+ * valid states passed to qib_set_linkstate() user call
+ */
+#define QIB_IB_LINKDOWN         0
+#define QIB_IB_LINKARM          1
+#define QIB_IB_LINKACTIVE       2
+#define QIB_IB_LINKDOWN_ONLY    3
+#define QIB_IB_LINKDOWN_SLEEP   4
+#define QIB_IB_LINKDOWN_DISABLE 5
+
+/*
+ * These 7 values (SDR, DDR, and QDR may be ORed for auto-speed
+ * negotiation) are used for the 3rd argument to path_f_set_ib_cfg
+ * with cmd QIB_IB_CFG_SPD_ENB, by direct calls or via sysfs.  They
+ * are also the the possible values for qib_link_speed_enabled and active
+ * The values were chosen to match values used within the IB spec.
+ */
+#define QIB_IB_SDR 1
+#define QIB_IB_DDR 2
+#define QIB_IB_QDR 4
+
+#define QIB_DEFAULT_MTU 4096
+
+/*
+ * Possible IB config parameters for f_get/set_ib_table()
+ */
+#define QIB_IB_TBL_VL_HIGH_ARB 1 /* Get/set VL high priority weights */
+#define QIB_IB_TBL_VL_LOW_ARB 2 /* Get/set VL low priority weights */
+
+/*
+ * Possible "operations" for f_rcvctrl(ppd, op, ctxt)
+ * these are bits so they can be combined, e.g.
+ * QIB_RCVCTRL_INTRAVAIL_ENB | QIB_RCVCTRL_CTXT_ENB
+ */
+#define QIB_RCVCTRL_TAILUPD_ENB 0x01
+#define QIB_RCVCTRL_TAILUPD_DIS 0x02
+#define QIB_RCVCTRL_CTXT_ENB 0x04
+#define QIB_RCVCTRL_CTXT_DIS 0x08
+#define QIB_RCVCTRL_INTRAVAIL_ENB 0x10
+#define QIB_RCVCTRL_INTRAVAIL_DIS 0x20
+#define QIB_RCVCTRL_PKEY_ENB 0x40  /* Note, default is enabled */
+#define QIB_RCVCTRL_PKEY_DIS 0x80
+#define QIB_RCVCTRL_BP_ENB 0x0100
+#define QIB_RCVCTRL_BP_DIS 0x0200
+#define QIB_RCVCTRL_TIDFLOW_ENB 0x0400
+#define QIB_RCVCTRL_TIDFLOW_DIS 0x0800
+
+/*
+ * Possible "operations" for f_sendctrl(ppd, op, var)
+ * these are bits so they can be combined, e.g.
+ * QIB_SENDCTRL_BUFAVAIL_ENB | QIB_SENDCTRL_ENB
+ * Some operations (e.g. DISARM, ABORT) are known to
+ * be "one-shot", so do not modify shadow.
+ */
+#define QIB_SENDCTRL_DISARM       (0x1000)
+#define QIB_SENDCTRL_DISARM_BUF(bufn) ((bufn) | QIB_SENDCTRL_DISARM)
+	/* available (0x2000) */
+#define QIB_SENDCTRL_AVAIL_DIS    (0x4000)
+#define QIB_SENDCTRL_AVAIL_ENB    (0x8000)
+#define QIB_SENDCTRL_AVAIL_BLIP  (0x10000)
+#define QIB_SENDCTRL_SEND_DIS    (0x20000)
+#define QIB_SENDCTRL_SEND_ENB    (0x40000)
+#define QIB_SENDCTRL_FLUSH       (0x80000)
+#define QIB_SENDCTRL_CLEAR      (0x100000)
+#define QIB_SENDCTRL_DISARM_ALL (0x200000)
+
+/*
+ * These are the generic indices for requesting per-port
+ * counter values via the f_portcntr function.  They
+ * are always returned as 64 bit values, although most
+ * are 32 bit counters.
+ */
+/* send-related counters */
+#define QIBPORTCNTR_PKTSEND         0U
+#define QIBPORTCNTR_WORDSEND        1U
+#define QIBPORTCNTR_PSXMITDATA      2U
+#define QIBPORTCNTR_PSXMITPKTS      3U
+#define QIBPORTCNTR_PSXMITWAIT      4U
+#define QIBPORTCNTR_SENDSTALL       5U
+/* receive-related counters */
+#define QIBPORTCNTR_PKTRCV          6U
+#define QIBPORTCNTR_PSRCVDATA       7U
+#define QIBPORTCNTR_PSRCVPKTS       8U
+#define QIBPORTCNTR_RCVEBP          9U
+#define QIBPORTCNTR_RCVOVFL         10U
+#define QIBPORTCNTR_WORDRCV         11U
+/* IB link related error counters */
+#define QIBPORTCNTR_RXLOCALPHYERR   12U
+#define QIBPORTCNTR_RXVLERR         13U
+#define QIBPORTCNTR_ERRICRC         14U
+#define QIBPORTCNTR_ERRVCRC         15U
+#define QIBPORTCNTR_ERRLPCRC        16U
+#define QIBPORTCNTR_BADFORMAT       17U
+#define QIBPORTCNTR_ERR_RLEN        18U
+#define QIBPORTCNTR_IBSYMBOLERR     19U
+#define QIBPORTCNTR_INVALIDRLEN     20U
+#define QIBPORTCNTR_UNSUPVL         21U
+#define QIBPORTCNTR_EXCESSBUFOVFL   22U
+#define QIBPORTCNTR_ERRLINK         23U
+#define QIBPORTCNTR_IBLINKDOWN      24U
+#define QIBPORTCNTR_IBLINKERRRECOV  25U
+#define QIBPORTCNTR_LLI             26U
+/* other error counters */
+#define QIBPORTCNTR_RXDROPPKT       27U
+#define QIBPORTCNTR_VL15PKTDROP     28U
+#define QIBPORTCNTR_ERRPKEY         29U
+#define QIBPORTCNTR_KHDROVFL        30U
+/* sampling counters (these are actually control registers) */
+#define QIBPORTCNTR_PSINTERVAL      31U
+#define QIBPORTCNTR_PSSTART         32U
+#define QIBPORTCNTR_PSSTAT          33U
+
+/* how often we check for packet activity for "power on hours (in seconds) */
+#define ACTIVITY_TIMER 5
+
+/* Below is an opaque struct. Each chip (device) can maintain
+ * private data needed for its operation, but not germane to the
+ * rest of the driver.  For convenience, we define another that
+ * is chip-specific, per-port
+ */
+struct qib_chip_specific;
+struct qib_chipport_specific;
+
+enum qib_sdma_states {
+	qib_sdma_state_s00_hw_down,
+	qib_sdma_state_s10_hw_start_up_wait,
+	qib_sdma_state_s20_idle,
+	qib_sdma_state_s30_sw_clean_up_wait,
+	qib_sdma_state_s40_hw_clean_up_wait,
+	qib_sdma_state_s50_hw_halt_wait,
+	qib_sdma_state_s99_running,
+};
+
+enum qib_sdma_events {
+	qib_sdma_event_e00_go_hw_down,
+	qib_sdma_event_e10_go_hw_start,
+	qib_sdma_event_e20_hw_started,
+	qib_sdma_event_e30_go_running,
+	qib_sdma_event_e40_sw_cleaned,
+	qib_sdma_event_e50_hw_cleaned,
+	qib_sdma_event_e60_hw_halted,
+	qib_sdma_event_e70_go_idle,
+	qib_sdma_event_e7220_err_halted,
+	qib_sdma_event_e7322_err_halted,
+	qib_sdma_event_e90_timer_tick,
+};
+
+extern char *qib_sdma_state_names[];
+extern char *qib_sdma_event_names[];
+
+struct sdma_set_state_action {
+	unsigned op_enable:1;
+	unsigned op_intenable:1;
+	unsigned op_halt:1;
+	unsigned op_drain:1;
+	unsigned go_s99_running_tofalse:1;
+	unsigned go_s99_running_totrue:1;
+};
+
+struct qib_sdma_state {
+	struct kref          kref;
+	struct completion    comp;
+	enum qib_sdma_states current_state;
+	struct sdma_set_state_action *set_state_action;
+	unsigned             current_op;
+	unsigned             go_s99_running;
+	unsigned             first_sendbuf;
+	unsigned             last_sendbuf; /* really last +1 */
+	/* debugging/devel */
+	enum qib_sdma_states previous_state;
+	unsigned             previous_op;
+	enum qib_sdma_events last_event;
+};
+
+/*
+ * The structure below encapsulates data relevant to a physical IB Port.
+ * Current chips support only one such port, but the separation
+ * clarifies things a bit. Note that to conform to IB conventions,
+ * port-numbers are one-based. The first or only port is port1.
+ */
+struct qib_pportdata {
+	struct qib_ibport ibport_data;
+
+	struct qib_devdata *dd;
+	struct qib_chippport_specific *cpspec; /* chip-specific per-port */
+	struct kobject pport_kobj;
+	struct kobject sl2vl_kobj;
+
+	/* GUID for this interface, in network order */
+	__be64 guid;
+
+	/* QIB_POLL, etc. link-state specific flags, per port */
+	u32 lflags;
+	/* qib_lflags driver is waiting for */
+	u32 state_wanted;
+	spinlock_t lflags_lock;
+	/* number of (port-specific) interrupts for this port -- saturates... */
+	u32 int_counter;
+
+	/* ref count for each pkey */
+	atomic_t pkeyrefs[4];
+
+	/*
+	 * this address is mapped readonly into user processes so they can
+	 * get status cheaply, whenever they want.  One qword of status per port
+	 */
+	u64 *statusp;
+
+	/* SendDMA related entries */
+	spinlock_t            sdma_lock;
+	struct qib_sdma_state sdma_state;
+	unsigned long         sdma_buf_jiffies;
+	struct qib_sdma_desc *sdma_descq;
+	u64                   sdma_descq_added;
+	u64                   sdma_descq_removed;
+	u16                   sdma_descq_cnt;
+	u16                   sdma_descq_tail;
+	u16                   sdma_descq_head;
+	u16                   sdma_next_intr;
+	u16                   sdma_reset_wait;
+	u8                    sdma_generation;
+	struct tasklet_struct sdma_sw_clean_up_task;
+	struct list_head      sdma_activelist;
+
+	dma_addr_t       sdma_descq_phys;
+	volatile __le64 *sdma_head_dma; /* DMA'ed by chip */
+	dma_addr_t       sdma_head_phys;
+
+	wait_queue_head_t state_wait; /* for state_wanted */
+
+	/* HoL blocking for SMP replies */
+	unsigned          hol_state;
+	struct timer_list hol_timer;
+
+	/*
+	 * Shadow copies of registers; size indicates read access size.
+	 * Most of them are readonly, but some are write-only register,
+	 * where we manipulate the bits in the shadow copy, and then write
+	 * the shadow copy to qlogic_ib.
+	 *
+	 * We deliberately make most of these 32 bits, since they have
+	 * restricted range.  For any that we read, we won't to generate 32
+	 * bit accesses, since Opteron will generate 2 separate 32 bit HT
+	 * transactions for a 64 bit read, and we want to avoid unnecessary
+	 * bus transactions.
+	 */
+
+	/* This is the 64 bit group */
+	/* last ibcstatus.  opaque outside chip-specific code */
+	u64 lastibcstat;
+
+	/* these are the "32 bit" regs */
+
+	/*
+	 * the following two are 32-bit bitmasks, but {test,clear,set}_bit
+	 * all expect bit fields to be "unsigned long"
+	 */
+	unsigned long p_rcvctrl; /* shadow per-port rcvctrl */
+	unsigned long p_sendctrl; /* shadow per-port sendctrl */
+
+	u32 ibmtu; /* The MTU programmed for this unit */
+	/*
+	 * Current max size IB packet (in bytes) including IB headers, that
+	 * we can send. Changes when ibmtu changes.
+	 */
+	u32 ibmaxlen;
+	/*
+	 * ibmaxlen at init time, limited by chip and by receive buffer
+	 * size.  Not changed after init.
+	 */
+	u32 init_ibmaxlen;
+	/* LID programmed for this instance */
+	u16 lid;
+	/* list of pkeys programmed; 0 if not set */
+	u16 pkeys[4];
+	/* LID mask control */
+	u8 lmc;
+	u8 link_width_supported;
+	u8 link_speed_supported;
+	u8 link_width_enabled;
+	u8 link_speed_enabled;
+	u8 link_width_active;
+	u8 link_speed_active;
+	u8 vls_supported;
+	u8 vls_operational;
+	/* Rx Polarity inversion (compensate for ~tx on partner) */
+	u8 rx_pol_inv;
+
+	u8 hw_pidx;     /* physical port index */
+	u8 port;        /* IB port number and index into dd->pports - 1 */
+
+	u8 delay_mult;
+
+	/* used to override LED behavior */
+	u8 led_override;  /* Substituted for normal value, if non-zero */
+	u16 led_override_timeoff; /* delta to next timer event */
+	u8 led_override_vals[2]; /* Alternates per blink-frame */
+	u8 led_override_phase; /* Just counts, LSB picks from vals[] */
+	atomic_t led_override_timer_active;
+	/* Used to flash LEDs in override mode */
+	struct timer_list led_override_timer;
+};
+
+/* Observers. Not to be taken lightly, possibly not to ship. */
+/*
+ * If a diag read or write is to (bottom <= offset <= top),
+ * the "hoook" is called, allowing, e.g. shadows to be
+ * updated in sync with the driver. struct diag_observer
+ * is the "visible" part.
+ */
+struct diag_observer;
+
+typedef int (*diag_hook) (struct qib_devdata *dd,
+	const struct diag_observer *op,
+	u32 offs, u64 *data, u64 mask, int only_32);
+
+struct diag_observer {
+	diag_hook hook;
+	u32 bottom;
+	u32 top;
+};
+
+extern int qib_register_observer(struct qib_devdata *dd,
+	const struct diag_observer *op);
+
+/* Only declared here, not defined. Private to diags */
+struct diag_observer_list_elt;
+
+/* device data struct now contains only "general per-device" info.
+ * fields related to a physical IB port are in a qib_pportdata struct,
+ * described above) while fields only used by a particualr chip-type are in
+ * a qib_chipdata struct, whose contents are opaque to this file.
+ */
+struct qib_devdata {
+	struct qib_ibdev verbs_dev;     /* must be first */
+	struct list_head list;
+	/* pointers to related structs for this device */
+	/* pci access data structure */
+	struct pci_dev *pcidev;
+	struct cdev *user_cdev;
+	struct cdev *diag_cdev;
+	struct device *user_device;
+	struct device *diag_device;
+
+	/* mem-mapped pointer to base of chip regs */
+	u64 __iomem *kregbase;
+	/* end of mem-mapped chip space excluding sendbuf and user regs */
+	u64 __iomem *kregend;
+	/* physical address of chip for io_remap, etc. */
+	resource_size_t physaddr;
+	/* qib_cfgctxts pointers */
+	struct qib_ctxtdata **rcd; /* Receive Context Data */
+
+	/* qib_pportdata, points to array of (physical) port-specific
+	 * data structs, indexed by pidx (0..n-1)
+	 */
+	struct qib_pportdata *pport;
+	struct qib_chip_specific *cspec; /* chip-specific */
+
+	/* kvirt address of 1st 2k pio buffer */
+	void __iomem *pio2kbase;
+	/* kvirt address of 1st 4k pio buffer */
+	void __iomem *pio4kbase;
+	/* mem-mapped pointer to base of PIO buffers (if using WC PAT) */
+	void __iomem *piobase;
+	/* mem-mapped pointer to base of user chip regs (if using WC PAT) */
+	u64 __iomem *userbase;
+	/*
+	 * points to area where PIOavail registers will be DMA'ed.
+	 * Has to be on a page of it's own, because the page will be
+	 * mapped into user program space.  This copy is *ONLY* ever
+	 * written by DMA, not by the driver!  Need a copy per device
+	 * when we get to multiple devices
+	 */
+	volatile __le64 *pioavailregs_dma; /* DMA'ed by chip */
+	/* physical address where updates occur */
+	dma_addr_t pioavailregs_phys;
+
+	/* device-specific implementations of functions needed by
+	 * common code. Contrary to previous consensus, we can't
+	 * really just point to a device-specific table, because we
+	 * may need to "bend", e.g. *_f_put_tid
+	 */
+	/* fallback to alternate interrupt type if possible */
+	int (*f_intr_fallback)(struct qib_devdata *);
+	/* hard reset chip */
+	int (*f_reset)(struct qib_devdata *);
+	void (*f_quiet_serdes)(struct qib_pportdata *);
+	int (*f_bringup_serdes)(struct qib_pportdata *);
+	int (*f_early_init)(struct qib_devdata *);
+	void (*f_clear_tids)(struct qib_devdata *, struct qib_ctxtdata *);
+	void (*f_put_tid)(struct qib_devdata *, u64 __iomem*,
+				u32, unsigned long);
+	void (*f_cleanup)(struct qib_devdata *);
+	void (*f_setextled)(struct qib_pportdata *, u32);
+	/* fill out chip-specific fields */
+	int (*f_get_base_info)(struct qib_ctxtdata *, struct qib_base_info *);
+	/* free irq */
+	void (*f_free_irq)(struct qib_devdata *);
+	struct qib_message_header *(*f_get_msgheader)
+					(struct qib_devdata *, __le32 *);
+	void (*f_config_ctxts)(struct qib_devdata *);
+	int (*f_get_ib_cfg)(struct qib_pportdata *, int);
+	int (*f_set_ib_cfg)(struct qib_pportdata *, int, u32);
+	int (*f_set_ib_loopback)(struct qib_pportdata *, const char *);
+	int (*f_get_ib_table)(struct qib_pportdata *, int, void *);
+	int (*f_set_ib_table)(struct qib_pportdata *, int, void *);
+	u32 (*f_iblink_state)(u64);
+	u8 (*f_ibphys_portstate)(u64);
+	void (*f_xgxs_reset)(struct qib_pportdata *);
+	/* per chip actions needed for IB Link up/down changes */
+	int (*f_ib_updown)(struct qib_pportdata *, int, u64);
+	u32 __iomem *(*f_getsendbuf)(struct qib_pportdata *, u64, u32 *);
+	/* Read/modify/write of GPIO pins (potentially chip-specific */
+	int (*f_gpio_mod)(struct qib_devdata *dd, u32 out, u32 dir,
+		u32 mask);
+	/* Enable writes to config EEPROM (if supported) */
+	int (*f_eeprom_wen)(struct qib_devdata *dd, int wen);
+	/*
+	 * modify rcvctrl shadow[s] and write to appropriate chip-regs.
+	 * see above QIB_RCVCTRL_xxx_ENB/DIS for operations.
+	 * (ctxt == -1) means "all contexts", only meaningful for
+	 * clearing. Could remove if chip_spec shutdown properly done.
+	 */
+	void (*f_rcvctrl)(struct qib_pportdata *, unsigned int op,
+		int ctxt);
+	/* Read/modify/write sendctrl appropriately for op and port. */
+	void (*f_sendctrl)(struct qib_pportdata *, u32 op);
+	void (*f_set_intr_state)(struct qib_devdata *, u32);
+	void (*f_set_armlaunch)(struct qib_devdata *, u32);
+	void (*f_wantpiobuf_intr)(struct qib_devdata *, u32);
+	int (*f_late_initreg)(struct qib_devdata *);
+	void (*f_dump_sdma_state)(struct qib_pportdata *);
+	int (*f_init_sdma_regs)(struct qib_pportdata *);
+	u16 (*f_sdma_gethead)(struct qib_pportdata *);
+	int (*f_sdma_busy)(struct qib_pportdata *);
+	void (*f_sdma_update_tail)(struct qib_pportdata *, u16);
+	void (*f_sdma_set_desc_cnt)(struct qib_pportdata *, unsigned);
+	void (*f_sdma_sendctrl)(struct qib_pportdata *, unsigned);
+	void (*f_sdma_hw_clean_up)(struct qib_pportdata *);
+	void (*f_sdma_hw_start_up)(struct qib_pportdata *);
+	void (*f_sdma_init_early)(struct qib_pportdata *);
+	int (*f_sdma_flush_sends)(struct qib_pportdata *);
+	void (*f_set_cntr_sample)(struct qib_pportdata *, u32, u32);
+	void (*f_update_usrhead)(struct qib_ctxtdata *, u64, u32, u32);
+	u32 (*f_hdrqempty)(struct qib_ctxtdata *);
+	u64 (*f_portcntr)(struct qib_pportdata *, u32);
+	u32 (*f_read_cntrs)(struct qib_devdata *, loff_t, char **,
+		u64 **);
+	u32 (*f_read_portcntrs)(struct qib_devdata *, loff_t, u32,
+		char **, u64 **);
+	u32 (*f_setpbc_control)(struct qib_pportdata *, u32, u8, u8);
+	void (*f_initvl15_bufs)(struct qib_devdata *);
+	void (*f_init_ctxt)(struct qib_ctxtdata *);
+	void (*f_txchk_change)(struct qib_devdata *, u32, u32, u32,
+		struct qib_ctxtdata *);
+	void (*f_writescratch)(struct qib_devdata *, u32);
+	int (*f_tempsense_rd)(struct qib_devdata *, int regnum);
+
+	char *boardname; /* human readable board info */
+
+	/* template for writing TIDs  */
+	u64 tidtemplate;
+	/* value to write to free TIDs */
+	u64 tidinvalid;
+
+	/* number of registers used for pioavail */
+	u32 pioavregs;
+	/* device (not port) flags, basically device capabilities */
+	u32 flags;
+	/* last buffer for user use */
+	u32 lastctxt_piobuf;
+
+	/* saturating counter of (non-port-specific) device interrupts */
+	u32 int_counter;
+
+	/* pio bufs allocated per ctxt */
+	u32 pbufsctxt;
+	/* if remainder on bufs/ctxt, ctxts < extrabuf get 1 extra */
+	u32 ctxts_extrabuf;
+	/*
+	 * number of ctxts configured as max; zero is set to number chip
+	 * supports, less gives more pio bufs/ctxt, etc.
+	 */
+	u32 cfgctxts;
+
+	/*
+	 * hint that we should update pioavailshadow before
+	 * looking for a PIO buffer
+	 */
+	u32 upd_pio_shadow;
+
+	/* internal debugging stats */
+	u32 maxpkts_call;
+	u32 avgpkts_call;
+	u64 nopiobufs;
+
+	/* PCI Vendor ID (here for NodeInfo) */
+	u16 vendorid;
+	/* PCI Device ID (here for NodeInfo) */
+	u16 deviceid;
+	/* for write combining settings */
+	unsigned long wc_cookie;
+	unsigned long wc_base;
+	unsigned long wc_len;
+
+	/* shadow copy of struct page *'s for exp tid pages */
+	struct page **pageshadow;
+	/* shadow copy of dma handles for exp tid pages */
+	dma_addr_t *physshadow;
+	u64 __iomem *egrtidbase;
+	spinlock_t sendctrl_lock; /* protect changes to sendctrl shadow */
+	/* around rcd and (user ctxts) ctxt_cnt use (intr vs free) */
+	spinlock_t uctxt_lock; /* rcd and user context changes */
+	/*
+	 * per unit status, see also portdata statusp
+	 * mapped readonly into user processes so they can get unit and
+	 * IB link status cheaply
+	 */
+	u64 *devstatusp;
+	char *freezemsg; /* freeze msg if hw error put chip in freeze */
+	u32 freezelen; /* max length of freezemsg */
+	/* timer used to prevent stats overflow, error throttling, etc. */
+	struct timer_list stats_timer;
+
+	/* timer to verify interrupts work, and fallback if possible */
+	struct timer_list intrchk_timer;
+	unsigned long ureg_align; /* user register alignment */
+
+	/*
+	 * Protects pioavailshadow, pioavailkernel, pio_need_disarm, and
+	 * pio_writing.
+	 */
+	spinlock_t pioavail_lock;
+
+	/*
+	 * Shadow copies of registers; size indicates read access size.
+	 * Most of them are readonly, but some are write-only register,
+	 * where we manipulate the bits in the shadow copy, and then write
+	 * the shadow copy to qlogic_ib.
+	 *
+	 * We deliberately make most of these 32 bits, since they have
+	 * restricted range.  For any that we read, we won't to generate 32
+	 * bit accesses, since Opteron will generate 2 separate 32 bit HT
+	 * transactions for a 64 bit read, and we want to avoid unnecessary
+	 * bus transactions.
+	 */
+
+	/* This is the 64 bit group */
+
+	unsigned long pioavailshadow[6];
+	/* bitmap of send buffers available for the kernel to use with PIO. */
+	unsigned long pioavailkernel[6];
+	/* bitmap of send buffers which need to be disarmed. */
+	unsigned long pio_need_disarm[3];
+	/* bitmap of send buffers which are being written to. */
+	unsigned long pio_writing[3];
+	/* kr_revision shadow */
+	u64 revision;
+	/* Base GUID for device (from eeprom, network order) */
+	__be64 base_guid;
+
+	/*
+	 * kr_sendpiobufbase value (chip offset of pio buffers), and the
+	 * base of the 2KB buffer s(user processes only use 2K)
+	 */
+	u64 piobufbase;
+	u32 pio2k_bufbase;
+
+	/* these are the "32 bit" regs */
+
+	/* number of GUIDs in the flash for this interface */
+	u32 nguid;
+	/*
+	 * the following two are 32-bit bitmasks, but {test,clear,set}_bit
+	 * all expect bit fields to be "unsigned long"
+	 */
+	unsigned long rcvctrl; /* shadow per device rcvctrl */
+	unsigned long sendctrl; /* shadow per device sendctrl */
+
+	/* value we put in kr_rcvhdrcnt */
+	u32 rcvhdrcnt;
+	/* value we put in kr_rcvhdrsize */
+	u32 rcvhdrsize;
+	/* value we put in kr_rcvhdrentsize */
+	u32 rcvhdrentsize;
+	/* kr_ctxtcnt value */
+	u32 ctxtcnt;
+	/* kr_pagealign value */
+	u32 palign;
+	/* number of "2KB" PIO buffers */
+	u32 piobcnt2k;
+	/* size in bytes of "2KB" PIO buffers */
+	u32 piosize2k;
+	/* max usable size in dwords of a "2KB" PIO buffer before going "4KB" */
+	u32 piosize2kmax_dwords;
+	/* number of "4KB" PIO buffers */
+	u32 piobcnt4k;
+	/* size in bytes of "4KB" PIO buffers */
+	u32 piosize4k;
+	/* kr_rcvegrbase value */
+	u32 rcvegrbase;
+	/* kr_rcvtidbase value */
+	u32 rcvtidbase;
+	/* kr_rcvtidcnt value */
+	u32 rcvtidcnt;
+	/* kr_userregbase */
+	u32 uregbase;
+	/* shadow the control register contents */
+	u32 control;
+
+	/* chip address space used by 4k pio buffers */
+	u32 align4k;
+	/* size of each rcvegrbuffer */
+	u32 rcvegrbufsize;
+	/* localbus width (1, 2,4,8,16,32) from config space  */
+	u32 lbus_width;
+	/* localbus speed in MHz */
+	u32 lbus_speed;
+	int unit; /* unit # of this chip */
+
+	/* start of CHIP_SPEC move to chipspec, but need code changes */
+	/* low and high portions of MSI capability/vector */
+	u32 msi_lo;
+	/* saved after PCIe init for restore after reset */
+	u32 msi_hi;
+	/* MSI data (vector) saved for restore */
+	u16 msi_data;
+	/* so we can rewrite it after a chip reset */
+	u32 pcibar0;
+	/* so we can rewrite it after a chip reset */
+	u32 pcibar1;
+	u64 rhdrhead_intr_off;
+
+	/*
+	 * ASCII serial number, from flash, large enough for original
+	 * all digit strings, and longer QLogic serial number format
+	 */
+	u8 serial[16];
+	/* human readable board version */
+	u8 boardversion[96];
+	u8 lbus_info[32]; /* human readable localbus info */
+	/* chip major rev, from qib_revision */
+	u8 majrev;
+	/* chip minor rev, from qib_revision */
+	u8 minrev;
+
+	/* Misc small ints */
+	/* Number of physical ports available */
+	u8 num_pports;
+	/* Lowest context number which can be used by user processes */
+	u8 first_user_ctxt;
+	u8 n_krcv_queues;
+	u8 qpn_mask;
+	u8 skip_kctxt_mask;
+
+	u16 rhf_offset; /* offset of RHF within receive header entry */
+
+	/*
+	 * GPIO pins for twsi-connected devices, and device code for eeprom
+	 */
+	u8 gpio_sda_num;
+	u8 gpio_scl_num;
+	u8 twsi_eeprom_dev;
+
+	/* Support (including locks) for EEPROM logging of errors and time */
+	/* control access to actual counters, timer */
+	spinlock_t eep_st_lock;
+	/* control high-level access to EEPROM */
+	struct mutex eep_lock;
+	uint64_t traffic_wds;
+	/* active time is kept in seconds, but logged in hours */
+	atomic_t active_time;
+	/* Below are nominal shadow of EEPROM, new since last EEPROM update */
+	uint8_t eep_st_errs[QIB_EEP_LOG_CNT];
+	uint8_t eep_st_new_errs[QIB_EEP_LOG_CNT];
+	uint16_t eep_hrs;
+	/*
+	 * masks for which bits of errs, hwerrs that cause
+	 * each of the counters to increment.
+	 */
+	struct qib_eep_log_mask eep_st_masks[QIB_EEP_LOG_CNT];
+	struct qib_diag_client *diag_client;
+	spinlock_t qib_diag_trans_lock; /* protect diag observer ops */
+	struct diag_observer_list_elt *diag_observer_list;
+};
+
+/* hol_state values */
+#define QIB_HOL_UP       0
+#define QIB_HOL_INIT     1
+
+#define QIB_SDMA_SENDCTRL_OP_ENABLE    (1U << 0)
+#define QIB_SDMA_SENDCTRL_OP_INTENABLE (1U << 1)
+#define QIB_SDMA_SENDCTRL_OP_HALT      (1U << 2)
+#define QIB_SDMA_SENDCTRL_OP_CLEANUP   (1U << 3)
+#define QIB_SDMA_SENDCTRL_OP_DRAIN     (1U << 4)
+
+/* operation types for f_txchk_change() */
+#define TXCHK_CHG_TYPE_DIS1  3
+#define TXCHK_CHG_TYPE_ENAB1 2
+#define TXCHK_CHG_TYPE_KERN  1
+#define TXCHK_CHG_TYPE_USER  0
+
+#define QIB_CHASE_TIME msecs_to_jiffies(145)
+#define QIB_CHASE_DIS_TIME msecs_to_jiffies(160)
+
+/* Private data for file operations */
+struct qib_filedata {
+	struct qib_ctxtdata *rcd;
+	unsigned subctxt;
+	unsigned tidcursor;
+	struct qib_user_sdma_queue *pq;
+};
+
+extern struct list_head qib_dev_list;
+extern spinlock_t qib_devs_lock;
+extern struct qib_devdata *qib_lookup(int unit);
+
+extern unsigned qib_wc_pat;
+int qib_init(struct qib_devdata *, int);
+int init_chip_wc_pat(struct qib_devdata *dd, u32);
+int qib_enable_wc(struct qib_devdata *dd);
+void qib_disable_wc(struct qib_devdata *dd);
+int qib_count_units(int *npresentp, int *nupp);
+int qib_count_active_units(void);
+
+int qib_cdev_init(int minor, const char *name,
+		  const struct file_operations *fops,
+		  struct cdev **cdevp, struct device **devp);
+void qib_cdev_cleanup(struct cdev **cdevp, struct device **devp);
+int qib_dev_init(void);
+void qib_dev_cleanup(void);
+
+int qib_diag_add(struct qib_devdata *);
+void qib_diag_remove(struct qib_devdata *);
+void qib_handle_e_ibstatuschanged(struct qib_pportdata *, u64);
+void qib_sdma_update_tail(struct qib_pportdata *, u16); /* hold sdma_lock */
+
+int qib_decode_err(struct qib_devdata *dd, char *buf, size_t blen, u64 err);
+void qib_bad_intrstatus(struct qib_devdata *);
+void qib_handle_urcv(struct qib_devdata *, u64);
+
+/* clean up any per-chip chip-specific stuff */
+void qib_chip_cleanup(struct qib_devdata *);
+/* clean up any chip type-specific stuff */
+void qib_chip_done(void);
+
+/* check to see if we have to force ordering for write combining */
+int qib_unordered_wc(void);
+void qib_pio_copy(void __iomem *to, const void *from, size_t count);
+
+void qib_disarm_piobufs(struct qib_devdata *, unsigned, unsigned);
+int qib_disarm_piobufs_ifneeded(struct qib_ctxtdata *);
+void qib_disarm_piobufs_set(struct qib_devdata *, unsigned long *, unsigned);
+void qib_cancel_sends(struct qib_pportdata *);
+
+int qib_create_rcvhdrq(struct qib_devdata *, struct qib_ctxtdata *);
+int qib_setup_eagerbufs(struct qib_ctxtdata *);
+void qib_set_ctxtcnt(struct qib_devdata *);
+int qib_create_ctxts(struct qib_devdata *dd);
+struct qib_ctxtdata *qib_create_ctxtdata(struct qib_pportdata *, u32);
+void qib_init_pportdata(struct qib_pportdata *, struct qib_devdata *, u8, u8);
+void qib_free_ctxtdata(struct qib_devdata *, struct qib_ctxtdata *);
+
+u32 qib_kreceive(struct qib_ctxtdata *, u32 *, u32 *);
+int qib_reset_device(int);
+int qib_wait_linkstate(struct qib_pportdata *, u32, int);
+int qib_set_linkstate(struct qib_pportdata *, u8);
+int qib_set_mtu(struct qib_pportdata *, u16);
+int qib_set_lid(struct qib_pportdata *, u32, u8);
+void qib_hol_down(struct qib_pportdata *);
+void qib_hol_init(struct qib_pportdata *);
+void qib_hol_up(struct qib_pportdata *);
+void qib_hol_event(unsigned long);
+void qib_disable_after_error(struct qib_devdata *);
+int qib_set_uevent_bits(struct qib_pportdata *, const int);
+
+/* for use in system calls, where we want to know device type, etc. */
+#define ctxt_fp(fp) \
+	(((struct qib_filedata *)(fp)->private_data)->rcd)
+#define subctxt_fp(fp) \
+	(((struct qib_filedata *)(fp)->private_data)->subctxt)
+#define tidcursor_fp(fp) \
+	(((struct qib_filedata *)(fp)->private_data)->tidcursor)
+#define user_sdma_queue_fp(fp) \
+	(((struct qib_filedata *)(fp)->private_data)->pq)
+
+static inline struct qib_devdata *dd_from_ppd(struct qib_pportdata *ppd)
+{
+	return ppd->dd;
+}
+
+static inline struct qib_devdata *dd_from_dev(struct qib_ibdev *dev)
+{
+	return container_of(dev, struct qib_devdata, verbs_dev);
+}
+
+static inline struct qib_devdata *dd_from_ibdev(struct ib_device *ibdev)
+{
+	return dd_from_dev(to_idev(ibdev));
+}
+
+static inline struct qib_pportdata *ppd_from_ibp(struct qib_ibport *ibp)
+{
+	return container_of(ibp, struct qib_pportdata, ibport_data);
+}
+
+static inline struct qib_ibport *to_iport(struct ib_device *ibdev, u8 port)
+{
+	struct qib_devdata *dd = dd_from_ibdev(ibdev);
+	unsigned pidx = port - 1; /* IB number port from 1, hdw from 0 */
+
+	WARN_ON(pidx >= dd->num_pports);
+	return &dd->pport[pidx].ibport_data;
+}
+
+/*
+ * values for dd->flags (_device_ related flags) and
+ */
+#define QIB_HAS_LINK_LATENCY  0x1 /* supports link latency (IB 1.2) */
+#define QIB_INITTED           0x2 /* chip and driver up and initted */
+#define QIB_DOING_RESET       0x4  /* in the middle of doing chip reset */
+#define QIB_PRESENT           0x8  /* chip accesses can be done */
+#define QIB_PIO_FLUSH_WC      0x10 /* Needs Write combining flush for PIO */
+#define QIB_HAS_THRESH_UPDATE 0x40
+#define QIB_HAS_SDMA_TIMEOUT  0x80
+#define QIB_USE_SPCL_TRIG     0x100 /* SpecialTrigger launch enabled */
+#define QIB_NODMA_RTAIL       0x200 /* rcvhdrtail register DMA enabled */
+#define QIB_HAS_INTX          0x800 /* Supports INTx interrupts */
+#define QIB_HAS_SEND_DMA      0x1000 /* Supports Send DMA */
+#define QIB_HAS_VLSUPP        0x2000 /* Supports multiple VLs; PBC different */
+#define QIB_HAS_HDRSUPP       0x4000 /* Supports header suppression */
+#define QIB_BADINTR           0x8000 /* severe interrupt problems */
+#define QIB_DCA_ENABLED       0x10000 /* Direct Cache Access enabled */
+#define QIB_HAS_QSFP          0x20000 /* device (card instance) has QSFP */
+
+/*
+ * values for ppd->lflags (_ib_port_ related flags)
+ */
+#define QIBL_LINKV             0x1 /* IB link state valid */
+#define QIBL_LINKDOWN          0x8 /* IB link is down */
+#define QIBL_LINKINIT          0x10 /* IB link level is up */
+#define QIBL_LINKARMED         0x20 /* IB link is ARMED */
+#define QIBL_LINKACTIVE        0x40 /* IB link is ACTIVE */
+/* leave a gap for more IB-link state */
+#define QIBL_IB_AUTONEG_INPROG 0x1000 /* non-IBTA DDR/QDR neg active */
+#define QIBL_IB_AUTONEG_FAILED 0x2000 /* non-IBTA DDR/QDR neg failed */
+#define QIBL_IB_LINK_DISABLED  0x4000 /* Linkdown-disable forced,
+				       * Do not try to bring up */
+#define QIBL_IB_FORCE_NOTIFY   0x8000 /* force notify on next ib change */
+
+/* IB dword length mask in PBC (lower 11 bits); same for all chips */
+#define QIB_PBC_LENGTH_MASK                     ((1 << 11) - 1)
+
+
+/* ctxt_flag bit offsets */
+		/* waiting for a packet to arrive */
+#define QIB_CTXT_WAITING_RCV   2
+		/* master has not finished initializing */
+#define QIB_CTXT_MASTER_UNINIT 4
+		/* waiting for an urgent packet to arrive */
+#define QIB_CTXT_WAITING_URG 5
+
+/* free up any allocated data at closes */
+void qib_free_data(struct qib_ctxtdata *dd);
+void qib_chg_pioavailkernel(struct qib_devdata *, unsigned, unsigned,
+			    u32, struct qib_ctxtdata *);
+struct qib_devdata *qib_init_iba7322_funcs(struct pci_dev *,
+					   const struct pci_device_id *);
+struct qib_devdata *qib_init_iba7220_funcs(struct pci_dev *,
+					   const struct pci_device_id *);
+struct qib_devdata *qib_init_iba6120_funcs(struct pci_dev *,
+					   const struct pci_device_id *);
+void qib_free_devdata(struct qib_devdata *);
+struct qib_devdata *qib_alloc_devdata(struct pci_dev *pdev, size_t extra);
+
+#define QIB_TWSI_NO_DEV 0xFF
+/* Below qib_twsi_ functions must be called with eep_lock held */
+int qib_twsi_reset(struct qib_devdata *dd);
+int qib_twsi_blk_rd(struct qib_devdata *dd, int dev, int addr, void *buffer,
+		    int len);
+int qib_twsi_blk_wr(struct qib_devdata *dd, int dev, int addr,
+		    const void *buffer, int len);
+void qib_get_eeprom_info(struct qib_devdata *);
+int qib_update_eeprom_log(struct qib_devdata *dd);
+void qib_inc_eeprom_err(struct qib_devdata *dd, u32 eidx, u32 incr);
+void qib_dump_lookup_output_queue(struct qib_devdata *);
+void qib_force_pio_avail_update(struct qib_devdata *);
+
+/*
+ * Set LED override, only the two LSBs have "public" meaning, but
+ * any non-zero value substitutes them for the Link and LinkTrain
+ * LED states.
+ */
+#define QIB_LED_PHYS 1 /* Physical (linktraining) GREEN LED */
+#define QIB_LED_LOG 2  /* Logical (link) YELLOW LED */
+void qib_set_led_override(struct qib_pportdata *ppd, unsigned int val);
+
+/* send dma routines */
+int qib_setup_sdma(struct qib_pportdata *);
+void qib_teardown_sdma(struct qib_pportdata *);
+void __qib_sdma_intr(struct qib_pportdata *);
+void qib_sdma_intr(struct qib_pportdata *);
+int qib_sdma_verbs_send(struct qib_pportdata *, struct qib_sge_state *,
+			u32, struct qib_verbs_txreq *);
+/* ppd->sdma_lock should be locked before calling this. */
+int qib_sdma_make_progress(struct qib_pportdata *dd);
+
+/* must be called under qib_sdma_lock */
+static inline u16 qib_sdma_descq_freecnt(const struct qib_pportdata *ppd)
+{
+	return ppd->sdma_descq_cnt -
+		(ppd->sdma_descq_added - ppd->sdma_descq_removed) - 1;
+}
+
+static inline int __qib_sdma_running(struct qib_pportdata *ppd)
+{
+	return ppd->sdma_state.current_state == qib_sdma_state_s99_running;
+}
+int qib_sdma_running(struct qib_pportdata *);
+
+void dump_sdma_state(struct qib_pportdata *ppd);
+void __qib_sdma_process_event(struct qib_pportdata *, enum qib_sdma_events);
+void qib_sdma_process_event(struct qib_pportdata *, enum qib_sdma_events);
+
+/*
+ * number of words used for protocol header if not set by qib_userinit();
+ */
+#define QIB_DFLT_RCVHDRSIZE 9
+
+/*
+ * We need to be able to handle an IB header of at least 24 dwords.
+ * We need the rcvhdrq large enough to handle largest IB header, but
+ * still have room for a 2KB MTU standard IB packet.
+ * Additionally, some processor/memory controller combinations
+ * benefit quite strongly from having the DMA'ed data be cacheline
+ * aligned and a cacheline multiple, so we set the size to 32 dwords
+ * (2 64-byte primary cachelines for pretty much all processors of
+ * interest).  The alignment hurts nothing, other than using somewhat
+ * more memory.
+ */
+#define QIB_RCVHDR_ENTSIZE 32
+
+int qib_get_user_pages(unsigned long, size_t, struct page **);
+void qib_release_user_pages(struct page **, size_t);
+int qib_eeprom_read(struct qib_devdata *, u8, void *, int);
+int qib_eeprom_write(struct qib_devdata *, u8, const void *, int);
+u32 __iomem *qib_getsendbuf_range(struct qib_devdata *, u32 *, u32, u32);
+void qib_sendbuf_done(struct qib_devdata *, unsigned);
+
+static inline void qib_clear_rcvhdrtail(const struct qib_ctxtdata *rcd)
+{
+	*((u64 *) rcd->rcvhdrtail_kvaddr) = 0ULL;
+}
+
+static inline u32 qib_get_rcvhdrtail(const struct qib_ctxtdata *rcd)
+{
+	/*
+	 * volatile because it's a DMA target from the chip, routine is
+	 * inlined, and don't want register caching or reordering.
+	 */
+	return (u32) le64_to_cpu(
+		*((volatile __le64 *)rcd->rcvhdrtail_kvaddr)); /* DMA'ed */
+}
+
+static inline u32 qib_get_hdrqtail(const struct qib_ctxtdata *rcd)
+{
+	const struct qib_devdata *dd = rcd->dd;
+	u32 hdrqtail;
+
+	if (dd->flags & QIB_NODMA_RTAIL) {
+		__le32 *rhf_addr;
+		u32 seq;
+
+		rhf_addr = (__le32 *) rcd->rcvhdrq +
+			rcd->head + dd->rhf_offset;
+		seq = qib_hdrget_seq(rhf_addr);
+		hdrqtail = rcd->head;
+		if (seq == rcd->seq_cnt)
+			hdrqtail++;
+	} else
+		hdrqtail = qib_get_rcvhdrtail(rcd);
+
+	return hdrqtail;
+}
+
+/*
+ * sysfs interface.
+ */
+
+extern const char ib_qib_version[];
+
+int qib_device_create(struct qib_devdata *);
+void qib_device_remove(struct qib_devdata *);
+
+int qib_verbs_register_sysfs(struct qib_devdata *);
+void qib_verbs_unregister_sysfs(struct qib_devdata *);
+/* Hook for sysfs read of QSFP */
+extern int qib_qsfp_dump(struct qib_pportdata *ppd, char *buf, int len);
+
+int __init qib_init_qibfs(void);
+int __exit qib_exit_qibfs(void);
+
+int qibfs_add(struct qib_devdata *);
+int qibfs_remove(struct qib_devdata *);
+
+int qib_pcie_init(struct pci_dev *, const struct pci_device_id *);
+int qib_pcie_ddinit(struct qib_devdata *, struct pci_dev *,
+		    const struct pci_device_id *);
+void qib_pcie_ddcleanup(struct qib_devdata *);
+int qib_pcie_params(struct qib_devdata *, u32, u32 *, struct msix_entry *);
+int qib_reinit_intr(struct qib_devdata *);
+void qib_enable_intx(struct pci_dev *);
+void qib_nomsi(struct qib_devdata *);
+void qib_nomsix(struct qib_devdata *);
+void qib_pcie_getcmd(struct qib_devdata *, u16 *, u8 *, u8 *);
+void qib_pcie_reenable(struct qib_devdata *, u16, u8, u8);
+
+/*
+ * dma_addr wrappers - all 0's invalid for hw
+ */
+dma_addr_t qib_map_page(struct pci_dev *, struct page *, unsigned long,
+			  size_t, int);
+const char *qib_get_unit_name(int unit);
+
+/*
+ * Flush write combining store buffers (if present) and perform a write
+ * barrier.
+ */
+#if defined(CONFIG_X86_64)
+#define qib_flush_wc() asm volatile("sfence" : : : "memory")
+#else
+#define qib_flush_wc() wmb() /* no reorder around wc flush */
+#endif
+
+/* global module parameter variables */
+extern unsigned qib_debug; /* debugging bit mask */
+extern unsigned qib_ibmtu;
+extern ushort qib_cfgctxts;
+extern ushort qib_num_cfg_vls;
+extern ushort qib_mini_init; /* If set, do few (ideally 0) writes to chip */
+extern unsigned qib_n_krcv_queues;
+extern unsigned qib_sdma_fetch_arb;
+extern unsigned qib_compat_ddr_negotiate;
+extern int qib_special_trigger;
+
+extern struct mutex qib_mutex;
+
+/* Number of seconds before our card status check...  */
+#define STATUS_TIMEOUT 60
+
+#define QIB_DRV_NAME            "ib_qib"
+#define QIB_USER_MINOR_BASE     0
+#define QIB_TRACE_MINOR         127
+#define QIB_DIAGPKT_MINOR       128
+#define QIB_DIAG_MINOR_BASE     129
+#define QIB_NMINORS             255
+
+#define PCI_VENDOR_ID_PATHSCALE 0x1fc1
+#define PCI_VENDOR_ID_QLOGIC 0x1077
+#define PCI_DEVICE_ID_QLOGIC_IB_6120 0x10
+#define PCI_DEVICE_ID_QLOGIC_IB_7220 0x7220
+#define PCI_DEVICE_ID_QLOGIC_IB_7322 0x7322
+
+/*
+ * qib_early_err is used (only!) to print early errors before devdata is
+ * allocated, or when dd->pcidev may not be valid, and at the tail end of
+ * cleanup when devdata may have been freed, etc.  qib_dev_porterr is
+ * the same as qib_dev_err, but is used when the message really needs
+ * the IB port# to be definitive as to what's happening..
+ * All of these go to the trace log, and the trace log entry is done
+ * first to avoid possible serial port delays from printk.
+ */
+#define qib_early_err(dev, fmt, ...) \
+	do { \
+		dev_info(dev, KERN_ERR QIB_DRV_NAME ": " fmt, ##__VA_ARGS__); \
+	} while (0)
+
+#define qib_dev_err(dd, fmt, ...) \
+	do { \
+		dev_err(&(dd)->pcidev->dev, "%s: " fmt, \
+			qib_get_unit_name((dd)->unit), ##__VA_ARGS__); \
+	} while (0)
+
+#define qib_dev_porterr(dd, port, fmt, ...) \
+	do { \
+		dev_err(&(dd)->pcidev->dev, "%s: IB%u:%u " fmt, \
+			qib_get_unit_name((dd)->unit), (dd)->unit, (port), \
+			##__VA_ARGS__); \
+	} while (0)
+
+#define qib_devinfo(pcidev, fmt, ...) \
+	do { \
+		dev_info(&(pcidev)->dev, fmt, ##__VA_ARGS__); \
+	} while (0)
+
+#if _QIB_DEBUGGING
+
+# define __QIB_DBG_WHICH(which, fmt, ...) \
+	do { \
+		if (unlikely(qib_debug & (which))) \
+			printk(KERN_DEBUG QIB_DRV_NAME ": " fmt, \
+				##__VA_ARGS__); \
+	} while (0)
+
+# define qib_dbg(fmt, ...) \
+	__QIB_DBG_WHICH(__QIB_DBG, fmt, ##__VA_ARGS__)
+# define qib_cdbg(which, fmt, ...) \
+	__QIB_DBG_WHICH(__QIB_##which##DBG, fmt, ##__VA_ARGS__)
+
+#else /* ! _QIB_DEBUGGING */
+
+# define qib_dbg(fmt, ...)
+# define qib_cdbg(which, fmt, ...)
+
+#endif /* _QIB_DEBUGGING */
+
+/*
+ * this is used for formatting hw error messages...
+ */
+struct qib_hwerror_msgs {
+	u64 mask;
+	const char *msg;
+};
+
+#define QLOGIC_IB_HWE_MSG(a, b) { .mask = a, .msg = b }
+
+/* in qib_intr.c... */
+void qib_format_hwerrors(u64 hwerrs,
+			 const struct qib_hwerror_msgs *hwerrmsgs,
+			 size_t nhwerrmsgs, char *msg, size_t lmsg);
+#endif                          /* _QIB_KERNEL_H */
