@@ -5038,4 +5038,2988 @@ void hfi1_read_link_quality(struct hfi1_devdata *dd, u8 *link_quality)
*link_quality = 0;
if (dd->pport->host_link_state & HLS_UP) {
- ret = read_8051_config(dd, LINK
\ No newline at end of file
+ ret = read_8051_config(dd, LINK_QUALITY_INFO, GENERAL_CONFIG,
+ &frame);
+ if (ret == 0)
+ *link_quality = (frame >> LINK_QUALITY_SHIFT)
+ & LINK_QUALITY_MASK;
+ }
+}
+
+static void read_planned_down_reason_code(struct hfi1_devdata *dd, u8 *pdrrc)
+{
+ u32 frame;
+
+ read_8051_config(dd, LINK_QUALITY_INFO, GENERAL_CONFIG, &frame);
+ *pdrrc = (frame >> DOWN_REMOTE_REASON_SHIFT) & DOWN_REMOTE_REASON_MASK;
+}
+
+static int read_tx_settings(struct hfi1_devdata *dd,
+ u8 *enable_lane_tx,
+ u8 *tx_polarity_inversion,
+ u8 *rx_polarity_inversion,
+ u8 *max_rate)
+{
+ u32 frame;
+ int ret;
+
+ ret = read_8051_config(dd, TX_SETTINGS, GENERAL_CONFIG, &frame);
+ *enable_lane_tx = (frame >> ENABLE_LANE_TX_SHIFT)
+ & ENABLE_LANE_TX_MASK;
+ *tx_polarity_inversion = (frame >> TX_POLARITY_INVERSION_SHIFT)
+ & TX_POLARITY_INVERSION_MASK;
+ *rx_polarity_inversion = (frame >> RX_POLARITY_INVERSION_SHIFT)
+ & RX_POLARITY_INVERSION_MASK;
+ *max_rate = (frame >> MAX_RATE_SHIFT) & MAX_RATE_MASK;
+ return ret;
+}
+
+static int write_tx_settings(struct hfi1_devdata *dd,
+ u8 enable_lane_tx,
+ u8 tx_polarity_inversion,
+ u8 rx_polarity_inversion,
+ u8 max_rate)
+{
+ u32 frame;
+
+ /* no need to mask, all variable sizes match field widths */
+ frame = enable_lane_tx << ENABLE_LANE_TX_SHIFT
+ | tx_polarity_inversion << TX_POLARITY_INVERSION_SHIFT
+ | rx_polarity_inversion << RX_POLARITY_INVERSION_SHIFT
+ | max_rate << MAX_RATE_SHIFT;
+ return load_8051_config(dd, TX_SETTINGS, GENERAL_CONFIG, frame);
+}
+
+static void check_fabric_firmware_versions(struct hfi1_devdata *dd)
+{
+ u32 frame, version, prod_id;
+ int ret, lane;
+
+ /* 4 lanes */
+ for (lane = 0; lane < 4; lane++) {
+ ret = read_8051_config(dd, SPICO_FW_VERSION, lane, &frame);
+ if (ret) {
+ dd_dev_err(
+ dd,
+ "Unable to read lane %d firmware details\n",
+ lane);
+ continue;
+ }
+ version = (frame >> SPICO_ROM_VERSION_SHIFT)
+ & SPICO_ROM_VERSION_MASK;
+ prod_id = (frame >> SPICO_ROM_PROD_ID_SHIFT)
+ & SPICO_ROM_PROD_ID_MASK;
+ dd_dev_info(dd,
+ "Lane %d firmware: version 0x%04x, prod_id 0x%04x\n",
+ lane, version, prod_id);
+ }
+}
+
+/*
+ * Read an idle LCB message.
+ *
+ * Returns 0 on success, -EINVAL on error
+ */
+static int read_idle_message(struct hfi1_devdata *dd, u64 type, u64 *data_out)
+{
+ int ret;
+
+ ret = do_8051_command(dd, HCMD_READ_LCB_IDLE_MSG,
+ type, data_out);
+ if (ret != HCMD_SUCCESS) {
+ dd_dev_err(dd, "read idle message: type %d, err %d\n",
+ (u32)type, ret);
+ return -EINVAL;
+ }
+ dd_dev_info(dd, "%s: read idle message 0x%llx\n", __func__, *data_out);
+ /* return only the payload as we already know the type */
+ *data_out >>= IDLE_PAYLOAD_SHIFT;
+ return 0;
+}
+
+/*
+ * Read an idle SMA message. To be done in response to a notification from
+ * the 8051.
+ *
+ * Returns 0 on success, -EINVAL on error
+ */
+static int read_idle_sma(struct hfi1_devdata *dd, u64 *data)
+{
+ return read_idle_message(dd,
+ (u64)IDLE_SMA << IDLE_MSG_TYPE_SHIFT, data);
+}
+
+/*
+ * Send an idle LCB message.
+ *
+ * Returns 0 on success, -EINVAL on error
+ */
+static int send_idle_message(struct hfi1_devdata *dd, u64 data)
+{
+ int ret;
+
+ dd_dev_info(dd, "%s: sending idle message 0x%llx\n", __func__, data);
+ ret = do_8051_command(dd, HCMD_SEND_LCB_IDLE_MSG, data, NULL);
+ if (ret != HCMD_SUCCESS) {
+ dd_dev_err(dd, "send idle message: data 0x%llx, err %d\n",
+ data, ret);
+ return -EINVAL;
+ }
+ return 0;
+}
+
+/*
+ * Send an idle SMA message.
+ *
+ * Returns 0 on success, -EINVAL on error
+ */
+int send_idle_sma(struct hfi1_devdata *dd, u64 message)
+{
+ u64 data;
+
+ data = ((message & IDLE_PAYLOAD_MASK) << IDLE_PAYLOAD_SHIFT)
+ | ((u64)IDLE_SMA << IDLE_MSG_TYPE_SHIFT);
+ return send_idle_message(dd, data);
+}
+
+/*
+ * Initialize the LCB then do a quick link up. This may or may not be
+ * in loopback.
+ *
+ * return 0 on success, -errno on error
+ */
+static int do_quick_linkup(struct hfi1_devdata *dd)
+{
+ u64 reg;
+ unsigned long timeout;
+ int ret;
+
+ lcb_shutdown(dd, 0);
+
+ if (loopback) {
+ /* LCB_CFG_LOOPBACK.VAL = 2 */
+ /* LCB_CFG_LANE_WIDTH.VAL = 0 */
+ write_csr(dd, DC_LCB_CFG_LOOPBACK,
+ IB_PACKET_TYPE << DC_LCB_CFG_LOOPBACK_VAL_SHIFT);
+ write_csr(dd, DC_LCB_CFG_LANE_WIDTH, 0);
+ }
+
+ /* start the LCBs */
+ /* LCB_CFG_TX_FIFOS_RESET.VAL = 0 */
+ write_csr(dd, DC_LCB_CFG_TX_FIFOS_RESET, 0);
+
+ /* simulator only loopback steps */
+ if (loopback && dd->icode == ICODE_FUNCTIONAL_SIMULATOR) {
+ /* LCB_CFG_RUN.EN = 1 */
+ write_csr(dd, DC_LCB_CFG_RUN,
+ 1ull << DC_LCB_CFG_RUN_EN_SHIFT);
+
+ /* watch LCB_STS_LINK_TRANSFER_ACTIVE */
+ timeout = jiffies + msecs_to_jiffies(10);
+ while (1) {
+ reg = read_csr(dd,
+ DC_LCB_STS_LINK_TRANSFER_ACTIVE);
+ if (reg)
+ break;
+ if (time_after(jiffies, timeout)) {
+ dd_dev_err(dd,
+ "timeout waiting for LINK_TRANSFER_ACTIVE\n");
+ return -ETIMEDOUT;
+ }
+ udelay(2);
+ }
+
+ write_csr(dd, DC_LCB_CFG_ALLOW_LINK_UP,
+ 1ull << DC_LCB_CFG_ALLOW_LINK_UP_VAL_SHIFT);
+ }
+
+ if (!loopback) {
+ /*
+ * When doing quick linkup and not in loopback, both
+ * sides must be done with LCB set-up before either
+ * starts the quick linkup. Put a delay here so that
+ * both sides can be started and have a chance to be
+ * done with LCB set up before resuming.
+ */
+ dd_dev_err(dd,
+ "Pausing for peer to be finished with LCB set up\n");
+ msleep(5000);
+ dd_dev_err(dd,
+ "Continuing with quick linkup\n");
+ }
+
+ write_csr(dd, DC_LCB_ERR_EN, 0); /* mask LCB errors */
+ set_8051_lcb_access(dd);
+
+ /*
+ * State "quick" LinkUp request sets the physical link state to
+ * LinkUp without a verify capability sequence.
+ * This state is in simulator v37 and later.
+ */
+ ret = set_physical_link_state(dd, PLS_QUICK_LINKUP);
+ if (ret != HCMD_SUCCESS) {
+ dd_dev_err(dd,
+ "%s: set physical link state to quick LinkUp failed with return %d\n",
+ __func__, ret);
+
+ set_host_lcb_access(dd);
+ write_csr(dd, DC_LCB_ERR_EN, ~0ull); /* watch LCB errors */
+
+ if (ret >= 0)
+ ret = -EINVAL;
+ return ret;
+ }
+
+ return 0; /* success */
+}
+
+/*
+ * Set the SerDes to internal loopback mode.
+ * Returns 0 on success, -errno on error.
+ */
+static int set_serdes_loopback_mode(struct hfi1_devdata *dd)
+{
+ int ret;
+
+ ret = set_physical_link_state(dd, PLS_INTERNAL_SERDES_LOOPBACK);
+ if (ret == HCMD_SUCCESS)
+ return 0;
+ dd_dev_err(dd,
+ "Set physical link state to SerDes Loopback failed with return %d\n",
+ ret);
+ if (ret >= 0)
+ ret = -EINVAL;
+ return ret;
+}
+
+/*
+ * Do all special steps to set up loopback.
+ */
+static int init_loopback(struct hfi1_devdata *dd)
+{
+ dd_dev_info(dd, "Entering loopback mode\n");
+
+ /* all loopbacks should disable self GUID check */
+ write_csr(dd, DC_DC8051_CFG_MODE,
+ (read_csr(dd, DC_DC8051_CFG_MODE) | DISABLE_SELF_GUID_CHECK));
+
+ /*
+ * The simulator has only one loopback option - LCB. Switch
+ * to that option, which includes quick link up.
+ *
+ * Accept all valid loopback values.
+ */
+ if ((dd->icode == ICODE_FUNCTIONAL_SIMULATOR)
+ && (loopback == LOOPBACK_SERDES
+ || loopback == LOOPBACK_LCB
+ || loopback == LOOPBACK_CABLE)) {
+ loopback = LOOPBACK_LCB;
+ quick_linkup = 1;
+ return 0;
+ }
+
+ /* handle serdes loopback */
+ if (loopback == LOOPBACK_SERDES) {
+ /* internal serdes loopack needs quick linkup on RTL */
+ if (dd->icode == ICODE_RTL_SILICON)
+ quick_linkup = 1;
+ return set_serdes_loopback_mode(dd);
+ }
+
+ /* LCB loopback - handled at poll time */
+ if (loopback == LOOPBACK_LCB) {
+ quick_linkup = 1; /* LCB is always quick linkup */
+
+ /* not supported in emulation due to emulation RTL changes */
+ if (dd->icode == ICODE_FPGA_EMULATION) {
+ dd_dev_err(dd,
+ "LCB loopback not supported in emulation\n");
+ return -EINVAL;
+ }
+ return 0;
+ }
+
+ /* external cable loopback requires no extra steps */
+ if (loopback == LOOPBACK_CABLE)
+ return 0;
+
+ dd_dev_err(dd, "Invalid loopback mode %d\n", loopback);
+ return -EINVAL;
+}
+
+/*
+ * Translate from the OPA_LINK_WIDTH handed to us by the FM to bits
+ * used in the Verify Capability link width attribute.
+ */
+static u16 opa_to_vc_link_widths(u16 opa_widths)
+{
+ int i;
+ u16 result = 0;
+
+ static const struct link_bits {
+ u16 from;
+ u16 to;
+ } opa_link_xlate[] = {
+ { OPA_LINK_WIDTH_1X, 1 << (1-1) },
+ { OPA_LINK_WIDTH_2X, 1 << (2-1) },
+ { OPA_LINK_WIDTH_3X, 1 << (3-1) },
+ { OPA_LINK_WIDTH_4X, 1 << (4-1) },
+ };
+
+ for (i = 0; i < ARRAY_SIZE(opa_link_xlate); i++) {
+ if (opa_widths & opa_link_xlate[i].from)
+ result |= opa_link_xlate[i].to;
+ }
+ return result;
+}
+
+/*
+ * Set link attributes before moving to polling.
+ */
+static int set_local_link_attributes(struct hfi1_pportdata *ppd)
+{
+ struct hfi1_devdata *dd = ppd->dd;
+ u8 enable_lane_tx;
+ u8 tx_polarity_inversion;
+ u8 rx_polarity_inversion;
+ int ret;
+
+ /* reset our fabric serdes to clear any lingering problems */
+ fabric_serdes_reset(dd);
+
+ /* set the local tx rate - need to read-modify-write */
+ ret = read_tx_settings(dd, &enable_lane_tx, &tx_polarity_inversion,
+ &rx_polarity_inversion, &ppd->local_tx_rate);
+ if (ret)
+ goto set_local_link_attributes_fail;
+
+ if (dd->dc8051_ver < dc8051_ver(0, 20)) {
+ /* set the tx rate to the fastest enabled */
+ if (ppd->link_speed_enabled & OPA_LINK_SPEED_25G)
+ ppd->local_tx_rate = 1;
+ else
+ ppd->local_tx_rate = 0;
+ } else {
+ /* set the tx rate to all enabled */
+ ppd->local_tx_rate = 0;
+ if (ppd->link_speed_enabled & OPA_LINK_SPEED_25G)
+ ppd->local_tx_rate |= 2;
+ if (ppd->link_speed_enabled & OPA_LINK_SPEED_12_5G)
+ ppd->local_tx_rate |= 1;
+ }
+ ret = write_tx_settings(dd, enable_lane_tx, tx_polarity_inversion,
+ rx_polarity_inversion, ppd->local_tx_rate);
+ if (ret != HCMD_SUCCESS)
+ goto set_local_link_attributes_fail;
+
+ /*
+ * DC supports continuous updates.
+ */
+ ret = write_vc_local_phy(dd, 0 /* no power management */,
+ 1 /* continuous updates */);
+ if (ret != HCMD_SUCCESS)
+ goto set_local_link_attributes_fail;
+
+ /* z=1 in the next call: AU of 0 is not supported by the hardware */
+ ret = write_vc_local_fabric(dd, dd->vau, 1, dd->vcu, dd->vl15_init,
+ ppd->port_crc_mode_enabled);
+ if (ret != HCMD_SUCCESS)
+ goto set_local_link_attributes_fail;
+
+ ret = write_vc_local_link_width(dd, 0, 0,
+ opa_to_vc_link_widths(ppd->link_width_enabled));
+ if (ret != HCMD_SUCCESS)
+ goto set_local_link_attributes_fail;
+
+ /* let peer know who we are */
+ ret = write_local_device_id(dd, dd->pcidev->device, dd->minrev);
+ if (ret == HCMD_SUCCESS)
+ return 0;
+
+set_local_link_attributes_fail:
+ dd_dev_err(dd,
+ "Failed to set local link attributes, return 0x%x\n",
+ ret);
+ return ret;
+}
+
+/*
+ * Call this to start the link. Schedule a retry if the cable is not
+ * present or if unable to start polling. Do not do anything if the
+ * link is disabled. Returns 0 if link is disabled or moved to polling
+ */
+int start_link(struct hfi1_pportdata *ppd)
+{
+ if (!ppd->link_enabled) {
+ dd_dev_info(ppd->dd,
+ "%s: stopping link start because link is disabled\n",
+ __func__);
+ return 0;
+ }
+ if (!ppd->driver_link_ready) {
+ dd_dev_info(ppd->dd,
+ "%s: stopping link start because driver is not ready\n",
+ __func__);
+ return 0;
+ }
+
+ if (qsfp_mod_present(ppd) || loopback == LOOPBACK_SERDES ||
+ loopback == LOOPBACK_LCB ||
+ ppd->dd->icode == ICODE_FUNCTIONAL_SIMULATOR)
+ return set_link_state(ppd, HLS_DN_POLL);
+
+ dd_dev_info(ppd->dd,
+ "%s: stopping link start because no cable is present\n",
+ __func__);
+ return -EAGAIN;
+}
+
+static void reset_qsfp(struct hfi1_pportdata *ppd)
+{
+ struct hfi1_devdata *dd = ppd->dd;
+ u64 mask, qsfp_mask;
+
+ mask = (u64)QSFP_HFI0_RESET_N;
+ qsfp_mask = read_csr(dd,
+ dd->hfi1_id ? ASIC_QSFP2_OE : ASIC_QSFP1_OE);
+ qsfp_mask |= mask;
+ write_csr(dd,
+ dd->hfi1_id ? ASIC_QSFP2_OE : ASIC_QSFP1_OE,
+ qsfp_mask);
+
+ qsfp_mask = read_csr(dd,
+ dd->hfi1_id ? ASIC_QSFP2_OUT : ASIC_QSFP1_OUT);
+ qsfp_mask &= ~mask;
+ write_csr(dd,
+ dd->hfi1_id ? ASIC_QSFP2_OUT : ASIC_QSFP1_OUT,
+ qsfp_mask);
+
+ udelay(10);
+
+ qsfp_mask |= mask;
+ write_csr(dd,
+ dd->hfi1_id ? ASIC_QSFP2_OUT : ASIC_QSFP1_OUT,
+ qsfp_mask);
+}
+
+static int handle_qsfp_error_conditions(struct hfi1_pportdata *ppd,
+ u8 *qsfp_interrupt_status)
+{
+ struct hfi1_devdata *dd = ppd->dd;
+
+ if ((qsfp_interrupt_status[0] & QSFP_HIGH_TEMP_ALARM) ||
+ (qsfp_interrupt_status[0] & QSFP_HIGH_TEMP_WARNING))
+ dd_dev_info(dd,
+ "%s: QSFP cable on fire\n",
+ __func__);
+
+ if ((qsfp_interrupt_status[0] & QSFP_LOW_TEMP_ALARM) ||
+ (qsfp_interrupt_status[0] & QSFP_LOW_TEMP_WARNING))
+ dd_dev_info(dd,
+ "%s: QSFP cable temperature too low\n",
+ __func__);
+
+ if ((qsfp_interrupt_status[1] & QSFP_HIGH_VCC_ALARM) ||
+ (qsfp_interrupt_status[1] & QSFP_HIGH_VCC_WARNING))
+ dd_dev_info(dd,
+ "%s: QSFP supply voltage too high\n",
+ __func__);
+
+ if ((qsfp_interrupt_status[1] & QSFP_LOW_VCC_ALARM) ||
+ (qsfp_interrupt_status[1] & QSFP_LOW_VCC_WARNING))
+ dd_dev_info(dd,
+ "%s: QSFP supply voltage too low\n",
+ __func__);
+
+ /* Byte 2 is vendor specific */
+
+ if ((qsfp_interrupt_status[3] & QSFP_HIGH_POWER_ALARM) ||
+ (qsfp_interrupt_status[3] & QSFP_HIGH_POWER_WARNING))
+ dd_dev_info(dd,
+ "%s: Cable RX channel 1/2 power too high\n",
+ __func__);
+
+ if ((qsfp_interrupt_status[3] & QSFP_LOW_POWER_ALARM) ||
+ (qsfp_interrupt_status[3] & QSFP_LOW_POWER_WARNING))
+ dd_dev_info(dd,
+ "%s: Cable RX channel 1/2 power too low\n",
+ __func__);
+
+ if ((qsfp_interrupt_status[4] & QSFP_HIGH_POWER_ALARM) ||
+ (qsfp_interrupt_status[4] & QSFP_HIGH_POWER_WARNING))
+ dd_dev_info(dd,
+ "%s: Cable RX channel 3/4 power too high\n",
+ __func__);
+
+ if ((qsfp_interrupt_status[4] & QSFP_LOW_POWER_ALARM) ||
+ (qsfp_interrupt_status[4] & QSFP_LOW_POWER_WARNING))
+ dd_dev_info(dd,
+ "%s: Cable RX channel 3/4 power too low\n",
+ __func__);
+
+ if ((qsfp_interrupt_status[5] & QSFP_HIGH_BIAS_ALARM) ||
+ (qsfp_interrupt_status[5] & QSFP_HIGH_BIAS_WARNING))
+ dd_dev_info(dd,
+ "%s: Cable TX channel 1/2 bias too high\n",
+ __func__);
+
+ if ((qsfp_interrupt_status[5] & QSFP_LOW_BIAS_ALARM) ||
+ (qsfp_interrupt_status[5] & QSFP_LOW_BIAS_WARNING))
+ dd_dev_info(dd,
+ "%s: Cable TX channel 1/2 bias too low\n",
+ __func__);
+
+ if ((qsfp_interrupt_status[6] & QSFP_HIGH_BIAS_ALARM) ||
+ (qsfp_interrupt_status[6] & QSFP_HIGH_BIAS_WARNING))
+ dd_dev_info(dd,
+ "%s: Cable TX channel 3/4 bias too high\n",
+ __func__);
+
+ if ((qsfp_interrupt_status[6] & QSFP_LOW_BIAS_ALARM) ||
+ (qsfp_interrupt_status[6] & QSFP_LOW_BIAS_WARNING))
+ dd_dev_info(dd,
+ "%s: Cable TX channel 3/4 bias too low\n",
+ __func__);
+
+ if ((qsfp_interrupt_status[7] & QSFP_HIGH_POWER_ALARM) ||
+ (qsfp_interrupt_status[7] & QSFP_HIGH_POWER_WARNING))
+ dd_dev_info(dd,
+ "%s: Cable TX channel 1/2 power too high\n",
+ __func__);
+
+ if ((qsfp_interrupt_status[7] & QSFP_LOW_POWER_ALARM) ||
+ (qsfp_interrupt_status[7] & QSFP_LOW_POWER_WARNING))
+ dd_dev_info(dd,
+ "%s: Cable TX channel 1/2 power too low\n",
+ __func__);
+
+ if ((qsfp_interrupt_status[8] & QSFP_HIGH_POWER_ALARM) ||
+ (qsfp_interrupt_status[8] & QSFP_HIGH_POWER_WARNING))
+ dd_dev_info(dd,
+ "%s: Cable TX channel 3/4 power too high\n",
+ __func__);
+
+ if ((qsfp_interrupt_status[8] & QSFP_LOW_POWER_ALARM) ||
+ (qsfp_interrupt_status[8] & QSFP_LOW_POWER_WARNING))
+ dd_dev_info(dd,
+ "%s: Cable TX channel 3/4 power too low\n",
+ __func__);
+
+ /* Bytes 9-10 and 11-12 are reserved */
+ /* Bytes 13-15 are vendor specific */
+
+ return 0;
+}
+
+static int do_pre_lni_host_behaviors(struct hfi1_pportdata *ppd)
+{
+ refresh_qsfp_cache(ppd, &ppd->qsfp_info);
+
+ return 0;
+}
+
+static int do_qsfp_intr_fallback(struct hfi1_pportdata *ppd)
+{
+ struct hfi1_devdata *dd = ppd->dd;
+ u8 qsfp_interrupt_status = 0;
+
+ if (qsfp_read(ppd, dd->hfi1_id, 2, &qsfp_interrupt_status, 1)
+ != 1) {
+ dd_dev_info(dd,
+ "%s: Failed to read status of QSFP module\n",
+ __func__);
+ return -EIO;
+ }
+
+ /* We don't care about alarms & warnings with a non-functional INT_N */
+ if (!(qsfp_interrupt_status & QSFP_DATA_NOT_READY))
+ do_pre_lni_host_behaviors(ppd);
+
+ return 0;
+}
+
+/* This routine will only be scheduled if the QSFP module is present */
+static void qsfp_event(struct work_struct *work)
+{
+ struct qsfp_data *qd;
+ struct hfi1_pportdata *ppd;
+ struct hfi1_devdata *dd;
+
+ qd = container_of(work, struct qsfp_data, qsfp_work);
+ ppd = qd->ppd;
+ dd = ppd->dd;
+
+ /* Sanity check */
+ if (!qsfp_mod_present(ppd))
+ return;
+
+ /*
+ * Turn DC back on after cables has been
+ * re-inserted. Up until now, the DC has been in
+ * reset to save power.
+ */
+ dc_start(dd);
+
+ if (qd->cache_refresh_required) {
+ msleep(3000);
+ reset_qsfp(ppd);
+
+ /* Check for QSFP interrupt after t_init (SFF 8679)
+ * + extra
+ */
+ msleep(3000);
+ if (!qd->qsfp_interrupt_functional) {
+ if (do_qsfp_intr_fallback(ppd) < 0)
+ dd_dev_info(dd, "%s: QSFP fallback failed\n",
+ __func__);
+ ppd->driver_link_ready = 1;
+ start_link(ppd);
+ }
+ }
+
+ if (qd->check_interrupt_flags) {
+ u8 qsfp_interrupt_status[16] = {0,};
+
+ if (qsfp_read(ppd, dd->hfi1_id, 6,
+ &qsfp_interrupt_status[0], 16) != 16) {
+ dd_dev_info(dd,
+ "%s: Failed to read status of QSFP module\n",
+ __func__);
+ } else {
+ unsigned long flags;
+ u8 data_status;
+
+ spin_lock_irqsave(&ppd->qsfp_info.qsfp_lock, flags);
+ ppd->qsfp_info.check_interrupt_flags = 0;
+ spin_unlock_irqrestore(&ppd->qsfp_info.qsfp_lock,
+ flags);
+
+ if (qsfp_read(ppd, dd->hfi1_id, 2, &data_status, 1)
+ != 1) {
+ dd_dev_info(dd,
+ "%s: Failed to read status of QSFP module\n",
+ __func__);
+ }
+ if (!(data_status & QSFP_DATA_NOT_READY)) {
+ do_pre_lni_host_behaviors(ppd);
+ start_link(ppd);
+ } else
+ handle_qsfp_error_conditions(ppd,
+ qsfp_interrupt_status);
+ }
+ }
+}
+
+void init_qsfp(struct hfi1_pportdata *ppd)
+{
+ struct hfi1_devdata *dd = ppd->dd;
+ u64 qsfp_mask;
+
+ if (loopback == LOOPBACK_SERDES || loopback == LOOPBACK_LCB ||
+ ppd->dd->icode == ICODE_FUNCTIONAL_SIMULATOR ||
+ !HFI1_CAP_IS_KSET(QSFP_ENABLED)) {
+ ppd->driver_link_ready = 1;
+ return;
+ }
+
+ ppd->qsfp_info.ppd = ppd;
+ INIT_WORK(&ppd->qsfp_info.qsfp_work, qsfp_event);
+
+ qsfp_mask = (u64)(QSFP_HFI0_INT_N | QSFP_HFI0_MODPRST_N);
+ /* Clear current status to avoid spurious interrupts */
+ write_csr(dd,
+ dd->hfi1_id ?
+ ASIC_QSFP2_CLEAR :
+ ASIC_QSFP1_CLEAR,
+ qsfp_mask);
+
+ /* Handle active low nature of INT_N and MODPRST_N pins */
+ if (qsfp_mod_present(ppd))
+ qsfp_mask &= ~(u64)QSFP_HFI0_MODPRST_N;
+ write_csr(dd,
+ dd->hfi1_id ? ASIC_QSFP2_INVERT : ASIC_QSFP1_INVERT,
+ qsfp_mask);
+
+ /* Allow only INT_N and MODPRST_N to trigger QSFP interrupts */
+ qsfp_mask |= (u64)QSFP_HFI0_MODPRST_N;
+ write_csr(dd,
+ dd->hfi1_id ? ASIC_QSFP2_MASK : ASIC_QSFP1_MASK,
+ qsfp_mask);
+
+ if (qsfp_mod_present(ppd)) {
+ msleep(3000);
+ reset_qsfp(ppd);
+
+ /* Check for QSFP interrupt after t_init (SFF 8679)
+ * + extra
+ */
+ msleep(3000);
+ if (!ppd->qsfp_info.qsfp_interrupt_functional) {
+ if (do_qsfp_intr_fallback(ppd) < 0)
+ dd_dev_info(dd,
+ "%s: QSFP fallback failed\n",
+ __func__);
+ ppd->driver_link_ready = 1;
+ }
+ }
+}
+
+int bringup_serdes(struct hfi1_pportdata *ppd)
+{
+ struct hfi1_devdata *dd = ppd->dd;
+ u64 guid;
+ int ret;
+
+ if (HFI1_CAP_IS_KSET(EXTENDED_PSN))
+ add_rcvctrl(dd, RCV_CTRL_RCV_EXTENDED_PSN_ENABLE_SMASK);
+
+ guid = ppd->guid;
+ if (!guid) {
+ if (dd->base_guid)
+ guid = dd->base_guid + ppd->port - 1;
+ ppd->guid = guid;
+ }
+
+ /* the link defaults to enabled */
+ ppd->link_enabled = 1;
+ /* Set linkinit_reason on power up per OPA spec */
+ ppd->linkinit_reason = OPA_LINKINIT_REASON_LINKUP;
+
+ if (loopback) {
+ ret = init_loopback(dd);
+ if (ret < 0)
+ return ret;
+ }
+
+ return start_link(ppd);
+}
+
+void hfi1_quiet_serdes(struct hfi1_pportdata *ppd)
+{
+ struct hfi1_devdata *dd = ppd->dd;
+
+ /*
+ * Shut down the link and keep it down. First turn off that the
+ * driver wants to allow the link to be up (driver_link_ready).
+ * Then make sure the link is not automatically restarted
+ * (link_enabled). Cancel any pending restart. And finally
+ * go offline.
+ */
+ ppd->driver_link_ready = 0;
+ ppd->link_enabled = 0;
+
+ set_link_down_reason(ppd, OPA_LINKDOWN_REASON_SMA_DISABLED, 0,
+ OPA_LINKDOWN_REASON_SMA_DISABLED);
+ set_link_state(ppd, HLS_DN_OFFLINE);
+
+ /* disable the port */
+ clear_rcvctrl(dd, RCV_CTRL_RCV_PORT_ENABLE_SMASK);
+}
+
+static inline int init_cpu_counters(struct hfi1_devdata *dd)
+{
+ struct hfi1_pportdata *ppd;
+ int i;
+
+ ppd = (struct hfi1_pportdata *)(dd + 1);
+ for (i = 0; i < dd->num_pports; i++, ppd++) {
+ ppd->ibport_data.rc_acks = NULL;
+ ppd->ibport_data.rc_qacks = NULL;
+ ppd->ibport_data.rc_acks = alloc_percpu(u64);
+ ppd->ibport_data.rc_qacks = alloc_percpu(u64);
+ ppd->ibport_data.rc_delayed_comp = alloc_percpu(u64);
+ if ((ppd->ibport_data.rc_acks == NULL) ||
+ (ppd->ibport_data.rc_delayed_comp == NULL) ||
+ (ppd->ibport_data.rc_qacks == NULL))
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+static const char * const pt_names[] = {
+ "expected",
+ "eager",
+ "invalid"
+};
+
+static const char *pt_name(u32 type)
+{
+ return type >= ARRAY_SIZE(pt_names) ? "unknown" : pt_names[type];
+}
+
+/*
+ * index is the index into the receive array
+ */
+void hfi1_put_tid(struct hfi1_devdata *dd, u32 index,
+ u32 type, unsigned long pa, u16 order)
+{
+ u64 reg;
+ void __iomem *base = (dd->rcvarray_wc ? dd->rcvarray_wc :
+ (dd->kregbase + RCV_ARRAY));
+
+ if (!(dd->flags & HFI1_PRESENT))
+ goto done;
+
+ if (type == PT_INVALID) {
+ pa = 0;
+ } else if (type > PT_INVALID) {
+ dd_dev_err(dd,
+ "unexpected receive array type %u for index %u, not handled\n",
+ type, index);
+ goto done;
+ }
+
+ hfi1_cdbg(TID, "type %s, index 0x%x, pa 0x%lx, bsize 0x%lx",
+ pt_name(type), index, pa, (unsigned long)order);
+
+#define RT_ADDR_SHIFT 12 /* 4KB kernel address boundary */
+ reg = RCV_ARRAY_RT_WRITE_ENABLE_SMASK
+ | (u64)order << RCV_ARRAY_RT_BUF_SIZE_SHIFT
+ | ((pa >> RT_ADDR_SHIFT) & RCV_ARRAY_RT_ADDR_MASK)
+ << RCV_ARRAY_RT_ADDR_SHIFT;
+ writeq(reg, base + (index * 8));
+
+ if (type == PT_EAGER)
+ /*
+ * Eager entries are written one-by-one so we have to push them
+ * after we write the entry.
+ */
+ flush_wc();
+done:
+ return;
+}
+
+void hfi1_clear_tids(struct hfi1_ctxtdata *rcd)
+{
+ struct hfi1_devdata *dd = rcd->dd;
+ u32 i;
+
+ /* this could be optimized */
+ for (i = rcd->eager_base; i < rcd->eager_base +
+ rcd->egrbufs.alloced; i++)
+ hfi1_put_tid(dd, i, PT_INVALID, 0, 0);
+
+ for (i = rcd->expected_base;
+ i < rcd->expected_base + rcd->expected_count; i++)
+ hfi1_put_tid(dd, i, PT_INVALID, 0, 0);
+}
+
+int hfi1_get_base_kinfo(struct hfi1_ctxtdata *rcd,
+ struct hfi1_ctxt_info *kinfo)
+{
+ kinfo->runtime_flags = (HFI1_MISC_GET() << HFI1_CAP_USER_SHIFT) |
+ HFI1_CAP_UGET(MASK) | HFI1_CAP_KGET(K2U);
+ return 0;
+}
+
+struct hfi1_message_header *hfi1_get_msgheader(
+ struct hfi1_devdata *dd, __le32 *rhf_addr)
+{
+ u32 offset = rhf_hdrq_offset(rhf_to_cpu(rhf_addr));
+
+ return (struct hfi1_message_header *)
+ (rhf_addr - dd->rhf_offset + offset);
+}
+
+static const char * const ib_cfg_name_strings[] = {
+ "HFI1_IB_CFG_LIDLMC",
+ "HFI1_IB_CFG_LWID_DG_ENB",
+ "HFI1_IB_CFG_LWID_ENB",
+ "HFI1_IB_CFG_LWID",
+ "HFI1_IB_CFG_SPD_ENB",
+ "HFI1_IB_CFG_SPD",
+ "HFI1_IB_CFG_RXPOL_ENB",
+ "HFI1_IB_CFG_LREV_ENB",
+ "HFI1_IB_CFG_LINKLATENCY",
+ "HFI1_IB_CFG_HRTBT",
+ "HFI1_IB_CFG_OP_VLS",
+ "HFI1_IB_CFG_VL_HIGH_CAP",
+ "HFI1_IB_CFG_VL_LOW_CAP",
+ "HFI1_IB_CFG_OVERRUN_THRESH",
+ "HFI1_IB_CFG_PHYERR_THRESH",
+ "HFI1_IB_CFG_LINKDEFAULT",
+ "HFI1_IB_CFG_PKEYS",
+ "HFI1_IB_CFG_MTU",
+ "HFI1_IB_CFG_LSTATE",
+ "HFI1_IB_CFG_VL_HIGH_LIMIT",
+ "HFI1_IB_CFG_PMA_TICKS",
+ "HFI1_IB_CFG_PORT"
+};
+
+static const char *ib_cfg_name(int which)
+{
+ if (which < 0 || which >= ARRAY_SIZE(ib_cfg_name_strings))
+ return "invalid";
+ return ib_cfg_name_strings[which];
+}
+
+int hfi1_get_ib_cfg(struct hfi1_pportdata *ppd, int which)
+{
+ struct hfi1_devdata *dd = ppd->dd;
+ int val = 0;
+
+ switch (which) {
+ case HFI1_IB_CFG_LWID_ENB: /* allowed Link-width */
+ val = ppd->link_width_enabled;
+ break;
+ case HFI1_IB_CFG_LWID: /* currently active Link-width */
+ val = ppd->link_width_active;
+ break;
+ case HFI1_IB_CFG_SPD_ENB: /* allowed Link speeds */
+ val = ppd->link_speed_enabled;
+ break;
+ case HFI1_IB_CFG_SPD: /* current Link speed */
+ val = ppd->link_speed_active;
+ break;
+
+ case HFI1_IB_CFG_RXPOL_ENB: /* Auto-RX-polarity enable */
+ case HFI1_IB_CFG_LREV_ENB: /* Auto-Lane-reversal enable */
+ case HFI1_IB_CFG_LINKLATENCY:
+ goto unimplemented;
+
+ case HFI1_IB_CFG_OP_VLS:
+ val = ppd->vls_operational;
+ break;
+ case HFI1_IB_CFG_VL_HIGH_CAP: /* VL arb high priority table size */
+ val = VL_ARB_HIGH_PRIO_TABLE_SIZE;
+ break;
+ case HFI1_IB_CFG_VL_LOW_CAP: /* VL arb low priority table size */
+ val = VL_ARB_LOW_PRIO_TABLE_SIZE;
+ break;
+ case HFI1_IB_CFG_OVERRUN_THRESH: /* IB overrun threshold */
+ val = ppd->overrun_threshold;
+ break;
+ case HFI1_IB_CFG_PHYERR_THRESH: /* IB PHY error threshold */
+ val = ppd->phy_error_threshold;
+ break;
+ case HFI1_IB_CFG_LINKDEFAULT: /* IB link default (sleep/poll) */
+ val = dd->link_default;
+ break;
+
+ case HFI1_IB_CFG_HRTBT: /* Heartbeat off/enable/auto */
+ case HFI1_IB_CFG_PMA_TICKS:
+ default:
+unimplemented:
+ if (HFI1_CAP_IS_KSET(PRINT_UNIMPL))
+ dd_dev_info(
+ dd,
+ "%s: which %s: not implemented\n",
+ __func__,
+ ib_cfg_name(which));
+ break;
+ }
+
+ return val;
+}
+
+/*
+ * The largest MAD packet size.
+ */
+#define MAX_MAD_PACKET 2048
+
+/*
+ * Return the maximum header bytes that can go on the _wire_
+ * for this device. This count includes the ICRC which is
+ * not part of the packet held in memory but it is appended
+ * by the HW.
+ * This is dependent on the device's receive header entry size.
+ * HFI allows this to be set per-receive context, but the
+ * driver presently enforces a global value.
+ */
+u32 lrh_max_header_bytes(struct hfi1_devdata *dd)
+{
+ /*
+ * The maximum non-payload (MTU) bytes in LRH.PktLen are
+ * the Receive Header Entry Size minus the PBC (or RHF) size
+ * plus one DW for the ICRC appended by HW.
+ *
+ * dd->rcd[0].rcvhdrqentsize is in DW.
+ * We use rcd[0] as all context will have the same value. Also,
+ * the first kernel context would have been allocated by now so
+ * we are guaranteed a valid value.
+ */
+ return (dd->rcd[0]->rcvhdrqentsize - 2/*PBC/RHF*/ + 1/*ICRC*/) << 2;
+}
+
+/*
+ * Set Send Length
+ * @ppd - per port data
+ *
+ * Set the MTU by limiting how many DWs may be sent. The SendLenCheck*
+ * registers compare against LRH.PktLen, so use the max bytes included
+ * in the LRH.
+ *
+ * This routine changes all VL values except VL15, which it maintains at
+ * the same value.
+ */
+static void set_send_length(struct hfi1_pportdata *ppd)
+{
+ struct hfi1_devdata *dd = ppd->dd;
+ u32 max_hb = lrh_max_header_bytes(dd), maxvlmtu = 0, dcmtu;
+ u64 len1 = 0, len2 = (((dd->vld[15].mtu + max_hb) >> 2)
+ & SEND_LEN_CHECK1_LEN_VL15_MASK) <<
+ SEND_LEN_CHECK1_LEN_VL15_SHIFT;
+ int i;
+
+ for (i = 0; i < ppd->vls_supported; i++) {
+ if (dd->vld[i].mtu > maxvlmtu)
+ maxvlmtu = dd->vld[i].mtu;
+ if (i <= 3)
+ len1 |= (((dd->vld[i].mtu + max_hb) >> 2)
+ & SEND_LEN_CHECK0_LEN_VL0_MASK) <<
+ ((i % 4) * SEND_LEN_CHECK0_LEN_VL1_SHIFT);
+ else
+ len2 |= (((dd->vld[i].mtu + max_hb) >> 2)
+ & SEND_LEN_CHECK1_LEN_VL4_MASK) <<
+ ((i % 4) * SEND_LEN_CHECK1_LEN_VL5_SHIFT);
+ }
+ write_csr(dd, SEND_LEN_CHECK0, len1);
+ write_csr(dd, SEND_LEN_CHECK1, len2);
+ /* adjust kernel credit return thresholds based on new MTUs */
+ /* all kernel receive contexts have the same hdrqentsize */
+ for (i = 0; i < ppd->vls_supported; i++) {
+ sc_set_cr_threshold(dd->vld[i].sc,
+ sc_mtu_to_threshold(dd->vld[i].sc, dd->vld[i].mtu,
+ dd->rcd[0]->rcvhdrqentsize));
+ }
+ sc_set_cr_threshold(dd->vld[15].sc,
+ sc_mtu_to_threshold(dd->vld[15].sc, dd->vld[15].mtu,
+ dd->rcd[0]->rcvhdrqentsize));
+
+ /* Adjust maximum MTU for the port in DC */
+ dcmtu = maxvlmtu == 10240 ? DCC_CFG_PORT_MTU_CAP_10240 :
+ (ilog2(maxvlmtu >> 8) + 1);
+ len1 = read_csr(ppd->dd, DCC_CFG_PORT_CONFIG);
+ len1 &= ~DCC_CFG_PORT_CONFIG_MTU_CAP_SMASK;
+ len1 |= ((u64)dcmtu & DCC_CFG_PORT_CONFIG_MTU_CAP_MASK) <<
+ DCC_CFG_PORT_CONFIG_MTU_CAP_SHIFT;
+ write_csr(ppd->dd, DCC_CFG_PORT_CONFIG, len1);
+}
+
+static void set_lidlmc(struct hfi1_pportdata *ppd)
+{
+ int i;
+ u64 sreg = 0;
+ struct hfi1_devdata *dd = ppd->dd;
+ u32 mask = ~((1U << ppd->lmc) - 1);
+ u64 c1 = read_csr(ppd->dd, DCC_CFG_PORT_CONFIG1);
+
+ if (dd->hfi1_snoop.mode_flag)
+ dd_dev_info(dd, "Set lid/lmc while snooping");
+
+ c1 &= ~(DCC_CFG_PORT_CONFIG1_TARGET_DLID_SMASK
+ | DCC_CFG_PORT_CONFIG1_DLID_MASK_SMASK);
+ c1 |= ((ppd->lid & DCC_CFG_PORT_CONFIG1_TARGET_DLID_MASK)
+ << DCC_CFG_PORT_CONFIG1_TARGET_DLID_SHIFT)|
+ ((mask & DCC_CFG_PORT_CONFIG1_DLID_MASK_MASK)
+ << DCC_CFG_PORT_CONFIG1_DLID_MASK_SHIFT);
+ write_csr(ppd->dd, DCC_CFG_PORT_CONFIG1, c1);
+
+ /*
+ * Iterate over all the send contexts and set their SLID check
+ */
+ sreg = ((mask & SEND_CTXT_CHECK_SLID_MASK_MASK) <<
+ SEND_CTXT_CHECK_SLID_MASK_SHIFT) |
+ (((ppd->lid & mask) & SEND_CTXT_CHECK_SLID_VALUE_MASK) <<
+ SEND_CTXT_CHECK_SLID_VALUE_SHIFT);
+
+ for (i = 0; i < dd->chip_send_contexts; i++) {
+ hfi1_cdbg(LINKVERB, "SendContext[%d].SLID_CHECK = 0x%x",
+ i, (u32)sreg);
+ write_kctxt_csr(dd, i, SEND_CTXT_CHECK_SLID, sreg);
+ }
+
+ /* Now we have to do the same thing for the sdma engines */
+ sdma_update_lmc(dd, mask, ppd->lid);
+}
+
+static int wait_phy_linkstate(struct hfi1_devdata *dd, u32 state, u32 msecs)
+{
+ unsigned long timeout;
+ u32 curr_state;
+
+ timeout = jiffies + msecs_to_jiffies(msecs);
+ while (1) {
+ curr_state = read_physical_state(dd);
+ if (curr_state == state)
+ break;
+ if (time_after(jiffies, timeout)) {
+ dd_dev_err(dd,
+ "timeout waiting for phy link state 0x%x, current state is 0x%x\n",
+ state, curr_state);
+ return -ETIMEDOUT;
+ }
+ usleep_range(1950, 2050); /* sleep 2ms-ish */
+ }
+
+ return 0;
+}
+
+/*
+ * Helper for set_link_state(). Do not call except from that routine.
+ * Expects ppd->hls_mutex to be held.
+ *
+ * @rem_reason value to be sent to the neighbor
+ *
+ * LinkDownReasons only set if transition succeeds.
+ */
+static int goto_offline(struct hfi1_pportdata *ppd, u8 rem_reason)
+{
+ struct hfi1_devdata *dd = ppd->dd;
+ u32 pstate, previous_state;
+ u32 last_local_state;
+ u32 last_remote_state;
+ int ret;
+ int do_transition;
+ int do_wait;
+
+ previous_state = ppd->host_link_state;
+ ppd->host_link_state = HLS_GOING_OFFLINE;
+ pstate = read_physical_state(dd);
+ if (pstate == PLS_OFFLINE) {
+ do_transition = 0; /* in right state */
+ do_wait = 0; /* ...no need to wait */
+ } else if ((pstate & 0xff) == PLS_OFFLINE) {
+ do_transition = 0; /* in an offline transient state */
+ do_wait = 1; /* ...wait for it to settle */
+ } else {
+ do_transition = 1; /* need to move to offline */
+ do_wait = 1; /* ...will need to wait */
+ }
+
+ if (do_transition) {
+ ret = set_physical_link_state(dd,
+ PLS_OFFLINE | (rem_reason << 8));
+
+ if (ret != HCMD_SUCCESS) {
+ dd_dev_err(dd,
+ "Failed to transition to Offline link state, return %d\n",
+ ret);
+ return -EINVAL;
+ }
+ if (ppd->offline_disabled_reason == OPA_LINKDOWN_REASON_NONE)
+ ppd->offline_disabled_reason =
+ OPA_LINKDOWN_REASON_TRANSIENT;
+ }
+
+ if (do_wait) {
+ /* it can take a while for the link to go down */
+ ret = wait_phy_linkstate(dd, PLS_OFFLINE, 5000);
+ if (ret < 0)
+ return ret;
+ }
+
+ /* make sure the logical state is also down */
+ wait_logical_linkstate(ppd, IB_PORT_DOWN, 1000);
+
+ /*
+ * Now in charge of LCB - must be after the physical state is
+ * offline.quiet and before host_link_state is changed.
+ */
+ set_host_lcb_access(dd);
+ write_csr(dd, DC_LCB_ERR_EN, ~0ull); /* watch LCB errors */
+ ppd->host_link_state = HLS_LINK_COOLDOWN; /* LCB access allowed */
+
+ /*
+ * The LNI has a mandatory wait time after the physical state
+ * moves to Offline.Quiet. The wait time may be different
+ * depending on how the link went down. The 8051 firmware
+ * will observe the needed wait time and only move to ready
+ * when that is completed. The largest of the quiet timeouts
+ * is 2.5s, so wait that long and then a bit more.
+ */
+ ret = wait_fm_ready(dd, 3000);
+ if (ret) {
+ dd_dev_err(dd,
+ "After going offline, timed out waiting for the 8051 to become ready to accept host requests\n");
+ /* state is really offline, so make it so */
+ ppd->host_link_state = HLS_DN_OFFLINE;
+ return ret;
+ }
+
+ /*
+ * The state is now offline and the 8051 is ready to accept host
+ * requests.
+ * - change our state
+ * - notify others if we were previously in a linkup state
+ */
+ ppd->host_link_state = HLS_DN_OFFLINE;
+ if (previous_state & HLS_UP) {
+ /* went down while link was up */
+ handle_linkup_change(dd, 0);
+ } else if (previous_state
+ & (HLS_DN_POLL | HLS_VERIFY_CAP | HLS_GOING_UP)) {
+ /* went down while attempting link up */
+ /* byte 1 of last_*_state is the failure reason */
+ read_last_local_state(dd, &last_local_state);
+ read_last_remote_state(dd, &last_remote_state);
+ dd_dev_err(dd,
+ "LNI failure last states: local 0x%08x, remote 0x%08x\n",
+ last_local_state, last_remote_state);
+ }
+
+ /* the active link width (downgrade) is 0 on link down */
+ ppd->link_width_active = 0;
+ ppd->link_width_downgrade_tx_active = 0;
+ ppd->link_width_downgrade_rx_active = 0;
+ ppd->current_egress_rate = 0;
+ return 0;
+}
+
+/* return the link state name */
+static const char *link_state_name(u32 state)
+{
+ const char *name;
+ int n = ilog2(state);
+ static const char * const names[] = {
+ [__HLS_UP_INIT_BP] = "INIT",
+ [__HLS_UP_ARMED_BP] = "ARMED",
+ [__HLS_UP_ACTIVE_BP] = "ACTIVE",
+ [__HLS_DN_DOWNDEF_BP] = "DOWNDEF",
+ [__HLS_DN_POLL_BP] = "POLL",
+ [__HLS_DN_DISABLE_BP] = "DISABLE",
+ [__HLS_DN_OFFLINE_BP] = "OFFLINE",
+ [__HLS_VERIFY_CAP_BP] = "VERIFY_CAP",
+ [__HLS_GOING_UP_BP] = "GOING_UP",
+ [__HLS_GOING_OFFLINE_BP] = "GOING_OFFLINE",
+ [__HLS_LINK_COOLDOWN_BP] = "LINK_COOLDOWN"
+ };
+
+ name = n < ARRAY_SIZE(names) ? names[n] : NULL;
+ return name ? name : "unknown";
+}
+
+/* return the link state reason name */
+static const char *link_state_reason_name(struct hfi1_pportdata *ppd, u32 state)
+{
+ if (state == HLS_UP_INIT) {
+ switch (ppd->linkinit_reason) {
+ case OPA_LINKINIT_REASON_LINKUP:
+ return "(LINKUP)";
+ case OPA_LINKINIT_REASON_FLAPPING:
+ return "(FLAPPING)";
+ case OPA_LINKINIT_OUTSIDE_POLICY:
+ return "(OUTSIDE_POLICY)";
+ case OPA_LINKINIT_QUARANTINED:
+ return "(QUARANTINED)";
+ case OPA_LINKINIT_INSUFIC_CAPABILITY:
+ return "(INSUFIC_CAPABILITY)";
+ default:
+ break;
+ }
+ }
+ return "";
+}
+
+/*
+ * driver_physical_state - convert the driver's notion of a port's
+ * state (an HLS_*) into a physical state (a {IB,OPA}_PORTPHYSSTATE_*).
+ * Return -1 (converted to a u32) to indicate error.
+ */
+u32 driver_physical_state(struct hfi1_pportdata *ppd)
+{
+ switch (ppd->host_link_state) {
+ case HLS_UP_INIT:
+ case HLS_UP_ARMED:
+ case HLS_UP_ACTIVE:
+ return IB_PORTPHYSSTATE_LINKUP;
+ case HLS_DN_POLL:
+ return IB_PORTPHYSSTATE_POLLING;
+ case HLS_DN_DISABLE:
+ return IB_PORTPHYSSTATE_DISABLED;
+ case HLS_DN_OFFLINE:
+ return OPA_PORTPHYSSTATE_OFFLINE;
+ case HLS_VERIFY_CAP:
+ return IB_PORTPHYSSTATE_POLLING;
+ case HLS_GOING_UP:
+ return IB_PORTPHYSSTATE_POLLING;
+ case HLS_GOING_OFFLINE:
+ return OPA_PORTPHYSSTATE_OFFLINE;
+ case HLS_LINK_COOLDOWN:
+ return OPA_PORTPHYSSTATE_OFFLINE;
+ case HLS_DN_DOWNDEF:
+ default:
+ dd_dev_err(ppd->dd, "invalid host_link_state 0x%x\n",
+ ppd->host_link_state);
+ return -1;
+ }
+}
+
+/*
+ * driver_logical_state - convert the driver's notion of a port's
+ * state (an HLS_*) into a logical state (a IB_PORT_*). Return -1
+ * (converted to a u32) to indicate error.
+ */
+u32 driver_logical_state(struct hfi1_pportdata *ppd)
+{
+ if (ppd->host_link_state && !(ppd->host_link_state & HLS_UP))
+ return IB_PORT_DOWN;
+
+ switch (ppd->host_link_state & HLS_UP) {
+ case HLS_UP_INIT:
+ return IB_PORT_INIT;
+ case HLS_UP_ARMED:
+ return IB_PORT_ARMED;
+ case HLS_UP_ACTIVE:
+ return IB_PORT_ACTIVE;
+ default:
+ dd_dev_err(ppd->dd, "invalid host_link_state 0x%x\n",
+ ppd->host_link_state);
+ return -1;
+ }
+}
+
+void set_link_down_reason(struct hfi1_pportdata *ppd, u8 lcl_reason,
+ u8 neigh_reason, u8 rem_reason)
+{
+ if (ppd->local_link_down_reason.latest == 0 &&
+ ppd->neigh_link_down_reason.latest == 0) {
+ ppd->local_link_down_reason.latest = lcl_reason;
+ ppd->neigh_link_down_reason.latest = neigh_reason;
+ ppd->remote_link_down_reason = rem_reason;
+ }
+}
+
+/*
+ * Change the physical and/or logical link state.
+ *
+ * Do not call this routine while inside an interrupt. It contains
+ * calls to routines that can take multiple seconds to finish.
+ *
+ * Returns 0 on success, -errno on failure.
+ */
+int set_link_state(struct hfi1_pportdata *ppd, u32 state)
+{
+ struct hfi1_devdata *dd = ppd->dd;
+ struct ib_event event = {.device = NULL};
+ int ret1, ret = 0;
+ int was_up, is_down;
+ int orig_new_state, poll_bounce;
+
+ mutex_lock(&ppd->hls_lock);
+
+ orig_new_state = state;
+ if (state == HLS_DN_DOWNDEF)
+ state = dd->link_default;
+
+ /* interpret poll -> poll as a link bounce */
+ poll_bounce = ppd->host_link_state == HLS_DN_POLL
+ && state == HLS_DN_POLL;
+
+ dd_dev_info(dd, "%s: current %s, new %s %s%s\n", __func__,
+ link_state_name(ppd->host_link_state),
+ link_state_name(orig_new_state),
+ poll_bounce ? "(bounce) " : "",
+ link_state_reason_name(ppd, state));
+
+ was_up = !!(ppd->host_link_state & HLS_UP);
+
+ /*
+ * If we're going to a (HLS_*) link state that implies the logical
+ * link state is neither of (IB_PORT_ARMED, IB_PORT_ACTIVE), then
+ * reset is_sm_config_started to 0.
+ */
+ if (!(state & (HLS_UP_ARMED | HLS_UP_ACTIVE)))
+ ppd->is_sm_config_started = 0;
+
+ /*
+ * Do nothing if the states match. Let a poll to poll link bounce
+ * go through.
+ */
+ if (ppd->host_link_state == state && !poll_bounce)
+ goto done;
+
+ switch (state) {
+ case HLS_UP_INIT:
+ if (ppd->host_link_state == HLS_DN_POLL && (quick_linkup
+ || dd->icode == ICODE_FUNCTIONAL_SIMULATOR)) {
+ /*
+ * Quick link up jumps from polling to here.
+ *
+ * Whether in normal or loopback mode, the
+ * simulator jumps from polling to link up.
+ * Accept that here.
+ */
+ /* OK */;
+ } else if (ppd->host_link_state != HLS_GOING_UP) {
+ goto unexpected;
+ }
+
+ ppd->host_link_state = HLS_UP_INIT;
+ ret = wait_logical_linkstate(ppd, IB_PORT_INIT, 1000);
+ if (ret) {
+ /* logical state didn't change, stay at going_up */
+ ppd->host_link_state = HLS_GOING_UP;
+ dd_dev_err(dd,
+ "%s: logical state did not change to INIT\n",
+ __func__);
+ } else {
+ /* clear old transient LINKINIT_REASON code */
+ if (ppd->linkinit_reason >= OPA_LINKINIT_REASON_CLEAR)
+ ppd->linkinit_reason =
+ OPA_LINKINIT_REASON_LINKUP;
+
+ /* enable the port */
+ add_rcvctrl(dd, RCV_CTRL_RCV_PORT_ENABLE_SMASK);
+
+ handle_linkup_change(dd, 1);
+ }
+ break;
+ case HLS_UP_ARMED:
+ if (ppd->host_link_state != HLS_UP_INIT)
+ goto unexpected;
+
+ ppd->host_link_state = HLS_UP_ARMED;
+ set_logical_state(dd, LSTATE_ARMED);
+ ret = wait_logical_linkstate(ppd, IB_PORT_ARMED, 1000);
+ if (ret) {
+ /* logical state didn't change, stay at init */
+ ppd->host_link_state = HLS_UP_INIT;
+ dd_dev_err(dd,
+ "%s: logical state did not change to ARMED\n",
+ __func__);
+ }
+ /*
+ * The simulator does not currently implement SMA messages,
+ * so neighbor_normal is not set. Set it here when we first
+ * move to Armed.
+ */
+ if (dd->icode == ICODE_FUNCTIONAL_SIMULATOR)
+ ppd->neighbor_normal = 1;
+ break;
+ case HLS_UP_ACTIVE:
+ if (ppd->host_link_state != HLS_UP_ARMED)
+ goto unexpected;
+
+ ppd->host_link_state = HLS_UP_ACTIVE;
+ set_logical_state(dd, LSTATE_ACTIVE);
+ ret = wait_logical_linkstate(ppd, IB_PORT_ACTIVE, 1000);
+ if (ret) {
+ /* logical state didn't change, stay at armed */
+ ppd->host_link_state = HLS_UP_ARMED;
+ dd_dev_err(dd,
+ "%s: logical state did not change to ACTIVE\n",
+ __func__);
+ } else {
+
+ /* tell all engines to go running */
+ sdma_all_running(dd);
+
+ /* Signal the IB layer that the port has went active */
+ event.device = &dd->verbs_dev.ibdev;
+ event.element.port_num = ppd->port;
+ event.event = IB_EVENT_PORT_ACTIVE;
+ }
+ break;
+ case HLS_DN_POLL:
+ if ((ppd->host_link_state == HLS_DN_DISABLE ||
+ ppd->host_link_state == HLS_DN_OFFLINE) &&
+ dd->dc_shutdown)
+ dc_start(dd);
+ /* Hand LED control to the DC */
+ write_csr(dd, DCC_CFG_LED_CNTRL, 0);
+
+ if (ppd->host_link_state != HLS_DN_OFFLINE) {
+ u8 tmp = ppd->link_enabled;
+
+ ret = goto_offline(ppd, ppd->remote_link_down_reason);
+ if (ret) {
+ ppd->link_enabled = tmp;
+ break;
+ }
+ ppd->remote_link_down_reason = 0;
+
+ if (ppd->driver_link_ready)
+ ppd->link_enabled = 1;
+ }
+
+ ret = set_local_link_attributes(ppd);
+ if (ret)
+ break;
+
+ ppd->port_error_action = 0;
+ ppd->host_link_state = HLS_DN_POLL;
+
+ if (quick_linkup) {
+ /* quick linkup does not go into polling */
+ ret = do_quick_linkup(dd);
+ } else {
+ ret1 = set_physical_link_state(dd, PLS_POLLING);
+ if (ret1 != HCMD_SUCCESS) {
+ dd_dev_err(dd,
+ "Failed to transition to Polling link state, return 0x%x\n",
+ ret1);
+ ret = -EINVAL;
+ }
+ }
+ ppd->offline_disabled_reason = OPA_LINKDOWN_REASON_NONE;
+ /*
+ * If an error occurred above, go back to offline. The
+ * caller may reschedule another attempt.
+ */
+ if (ret)
+ goto_offline(ppd, 0);
+ break;
+ case HLS_DN_DISABLE:
+ /* link is disabled */
+ ppd->link_enabled = 0;
+
+ /* allow any state to transition to disabled */
+
+ /* must transition to offline first */
+ if (ppd->host_link_state != HLS_DN_OFFLINE) {
+ ret = goto_offline(ppd, ppd->remote_link_down_reason);
+ if (ret)
+ break;
+ ppd->remote_link_down_reason = 0;
+ }
+
+ ret1 = set_physical_link_state(dd, PLS_DISABLED);
+ if (ret1 != HCMD_SUCCESS) {
+ dd_dev_err(dd,
+ "Failed to transition to Disabled link state, return 0x%x\n",
+ ret1);
+ ret = -EINVAL;
+ break;
+ }
+ ppd->host_link_state = HLS_DN_DISABLE;
+ dc_shutdown(dd);
+ break;
+ case HLS_DN_OFFLINE:
+ if (ppd->host_link_state == HLS_DN_DISABLE)
+ dc_start(dd);
+
+ /* allow any state to transition to offline */
+ ret = goto_offline(ppd, ppd->remote_link_down_reason);
+ if (!ret)
+ ppd->remote_link_down_reason = 0;
+ break;
+ case HLS_VERIFY_CAP:
+ if (ppd->host_link_state != HLS_DN_POLL)
+ goto unexpected;
+ ppd->host_link_state = HLS_VERIFY_CAP;
+ break;
+ case HLS_GOING_UP:
+ if (ppd->host_link_state != HLS_VERIFY_CAP)
+ goto unexpected;
+
+ ret1 = set_physical_link_state(dd, PLS_LINKUP);
+ if (ret1 != HCMD_SUCCESS) {
+ dd_dev_err(dd,
+ "Failed to transition to link up state, return 0x%x\n",
+ ret1);
+ ret = -EINVAL;
+ break;
+ }
+ ppd->host_link_state = HLS_GOING_UP;
+ break;
+
+ case HLS_GOING_OFFLINE: /* transient within goto_offline() */
+ case HLS_LINK_COOLDOWN: /* transient within goto_offline() */
+ default:
+ dd_dev_info(dd, "%s: state 0x%x: not supported\n",
+ __func__, state);
+ ret = -EINVAL;
+ break;
+ }
+
+ is_down = !!(ppd->host_link_state & (HLS_DN_POLL |
+ HLS_DN_DISABLE | HLS_DN_OFFLINE));
+
+ if (was_up && is_down && ppd->local_link_down_reason.sma == 0 &&
+ ppd->neigh_link_down_reason.sma == 0) {
+ ppd->local_link_down_reason.sma =
+ ppd->local_link_down_reason.latest;
+ ppd->neigh_link_down_reason.sma =
+ ppd->neigh_link_down_reason.latest;
+ }
+
+ goto done;
+
+unexpected:
+ dd_dev_err(dd, "%s: unexpected state transition from %s to %s\n",
+ __func__, link_state_name(ppd->host_link_state),
+ link_state_name(state));
+ ret = -EINVAL;
+
+done:
+ mutex_unlock(&ppd->hls_lock);
+
+ if (event.device)
+ ib_dispatch_event(&event);
+
+ return ret;
+}
+
+int hfi1_set_ib_cfg(struct hfi1_pportdata *ppd, int which, u32 val)
+{
+ u64 reg;
+ int ret = 0;
+
+ switch (which) {
+ case HFI1_IB_CFG_LIDLMC:
+ set_lidlmc(ppd);
+ break;
+ case HFI1_IB_CFG_VL_HIGH_LIMIT:
+ /*
+ * The VL Arbitrator high limit is sent in units of 4k
+ * bytes, while HFI stores it in units of 64 bytes.
+ */
+ val *= 4096/64;
+ reg = ((u64)val & SEND_HIGH_PRIORITY_LIMIT_LIMIT_MASK)
+ << SEND_HIGH_PRIORITY_LIMIT_LIMIT_SHIFT;
+ write_csr(ppd->dd, SEND_HIGH_PRIORITY_LIMIT, reg);
+ break;
+ case HFI1_IB_CFG_LINKDEFAULT: /* IB link default (sleep/poll) */
+ /* HFI only supports POLL as the default link down state */
+ if (val != HLS_DN_POLL)
+ ret = -EINVAL;
+ break;
+ case HFI1_IB_CFG_OP_VLS:
+ if (ppd->vls_operational != val) {
+ ppd->vls_operational = val;
+ if (!ppd->port)
+ ret = -EINVAL;
+ else
+ ret = sdma_map_init(
+ ppd->dd,
+ ppd->port - 1,
+ val,
+ NULL);
+ }
+ break;
+ /*
+ * For link width, link width downgrade, and speed enable, always AND
+ * the setting with what is actually supported. This has two benefits.
+ * First, enabled can't have unsupported values, no matter what the
+ * SM or FM might want. Second, the ALL_SUPPORTED wildcards that mean
+ * "fill in with your supported value" have all the bits in the
+ * field set, so simply ANDing with supported has the desired result.
+ */
+ case HFI1_IB_CFG_LWID_ENB: /* set allowed Link-width */
+ ppd->link_width_enabled = val & ppd->link_width_supported;
+ break;
+ case HFI1_IB_CFG_LWID_DG_ENB: /* set allowed link width downgrade */
+ ppd->link_width_downgrade_enabled =
+ val & ppd->link_width_downgrade_supported;
+ break;
+ case HFI1_IB_CFG_SPD_ENB: /* allowed Link speeds */
+ ppd->link_speed_enabled = val & ppd->link_speed_supported;
+ break;
+ case HFI1_IB_CFG_OVERRUN_THRESH: /* IB overrun threshold */
+ /*
+ * HFI does not follow IB specs, save this value
+ * so we can report it, if asked.
+ */
+ ppd->overrun_threshold = val;
+ break;
+ case HFI1_IB_CFG_PHYERR_THRESH: /* IB PHY error threshold */
+ /*
+ * HFI does not follow IB specs, save this value
+ * so we can report it, if asked.
+ */
+ ppd->phy_error_threshold = val;
+ break;
+
+ case HFI1_IB_CFG_MTU:
+ set_send_length(ppd);
+ break;
+
+ case HFI1_IB_CFG_PKEYS:
+ if (HFI1_CAP_IS_KSET(PKEY_CHECK))
+ set_partition_keys(ppd);
+ break;
+
+ default:
+ if (HFI1_CAP_IS_KSET(PRINT_UNIMPL))
+ dd_dev_info(ppd->dd,
+ "%s: which %s, val 0x%x: not implemented\n",
+ __func__, ib_cfg_name(which), val);
+ break;
+ }
+ return ret;
+}
+
+/* begin functions related to vl arbitration table caching */
+static void init_vl_arb_caches(struct hfi1_pportdata *ppd)
+{
+ int i;
+
+ BUILD_BUG_ON(VL_ARB_TABLE_SIZE !=
+ VL_ARB_LOW_PRIO_TABLE_SIZE);
+ BUILD_BUG_ON(VL_ARB_TABLE_SIZE !=
+ VL_ARB_HIGH_PRIO_TABLE_SIZE);
+
+ /*
+ * Note that we always return values directly from the
+ * 'vl_arb_cache' (and do no CSR reads) in response to a
+ * 'Get(VLArbTable)'. This is obviously correct after a
+ * 'Set(VLArbTable)', since the cache will then be up to
+ * date. But it's also correct prior to any 'Set(VLArbTable)'
+ * since then both the cache, and the relevant h/w registers
+ * will be zeroed.
+ */
+
+ for (i = 0; i < MAX_PRIO_TABLE; i++)
+ spin_lock_init(&ppd->vl_arb_cache[i].lock);
+}
+
+/*
+ * vl_arb_lock_cache
+ *
+ * All other vl_arb_* functions should be called only after locking
+ * the cache.
+ */
+static inline struct vl_arb_cache *
+vl_arb_lock_cache(struct hfi1_pportdata *ppd, int idx)
+{
+ if (idx != LO_PRIO_TABLE && idx != HI_PRIO_TABLE)
+ return NULL;
+ spin_lock(&ppd->vl_arb_cache[idx].lock);
+ return &ppd->vl_arb_cache[idx];
+}
+
+static inline void vl_arb_unlock_cache(struct hfi1_pportdata *ppd, int idx)
+{
+ spin_unlock(&ppd->vl_arb_cache[idx].lock);
+}
+
+static void vl_arb_get_cache(struct vl_arb_cache *cache,
+ struct ib_vl_weight_elem *vl)
+{
+ memcpy(vl, cache->table, VL_ARB_TABLE_SIZE * sizeof(*vl));
+}
+
+static void vl_arb_set_cache(struct vl_arb_cache *cache,
+ struct ib_vl_weight_elem *vl)
+{
+ memcpy(cache->table, vl, VL_ARB_TABLE_SIZE * sizeof(*vl));
+}
+
+static int vl_arb_match_cache(struct vl_arb_cache *cache,
+ struct ib_vl_weight_elem *vl)
+{
+ return !memcmp(cache->table, vl, VL_ARB_TABLE_SIZE * sizeof(*vl));
+}
+/* end functions related to vl arbitration table caching */
+
+static int set_vl_weights(struct hfi1_pportdata *ppd, u32 target,
+ u32 size, struct ib_vl_weight_elem *vl)
+{
+ struct hfi1_devdata *dd = ppd->dd;
+ u64 reg;
+ unsigned int i, is_up = 0;
+ int drain, ret = 0;
+
+ mutex_lock(&ppd->hls_lock);
+
+ if (ppd->host_link_state & HLS_UP)
+ is_up = 1;
+
+ drain = !is_ax(dd) && is_up;
+
+ if (drain)
+ /*
+ * Before adjusting VL arbitration weights, empty per-VL
+ * FIFOs, otherwise a packet whose VL weight is being
+ * set to 0 could get stuck in a FIFO with no chance to
+ * egress.
+ */
+ ret = stop_drain_data_vls(dd);
+
+ if (ret) {
+ dd_dev_err(
+ dd,
+ "%s: cannot stop/drain VLs - refusing to change VL arbitration weights\n",
+ __func__);
+ goto err;
+ }
+
+ for (i = 0; i < size; i++, vl++) {
+ /*
+ * NOTE: The low priority shift and mask are used here, but
+ * they are the same for both the low and high registers.
+ */
+ reg = (((u64)vl->vl & SEND_LOW_PRIORITY_LIST_VL_MASK)
+ << SEND_LOW_PRIORITY_LIST_VL_SHIFT)
+ | (((u64)vl->weight
+ & SEND_LOW_PRIORITY_LIST_WEIGHT_MASK)
+ << SEND_LOW_PRIORITY_LIST_WEIGHT_SHIFT);
+ write_csr(dd, target + (i * 8), reg);
+ }
+ pio_send_control(dd, PSC_GLOBAL_VLARB_ENABLE);
+
+ if (drain)
+ open_fill_data_vls(dd); /* reopen all VLs */
+
+err:
+ mutex_unlock(&ppd->hls_lock);
+
+ return ret;
+}
+
+/*
+ * Read one credit merge VL register.
+ */
+static void read_one_cm_vl(struct hfi1_devdata *dd, u32 csr,
+ struct vl_limit *vll)
+{
+ u64 reg = read_csr(dd, csr);
+
+ vll->dedicated = cpu_to_be16(
+ (reg >> SEND_CM_CREDIT_VL_DEDICATED_LIMIT_VL_SHIFT)
+ & SEND_CM_CREDIT_VL_DEDICATED_LIMIT_VL_MASK);
+ vll->shared = cpu_to_be16(
+ (reg >> SEND_CM_CREDIT_VL_SHARED_LIMIT_VL_SHIFT)
+ & SEND_CM_CREDIT_VL_SHARED_LIMIT_VL_MASK);
+}
+
+/*
+ * Read the current credit merge limits.
+ */
+static int get_buffer_control(struct hfi1_devdata *dd,
+ struct buffer_control *bc, u16 *overall_limit)
+{
+ u64 reg;
+ int i;
+
+ /* not all entries are filled in */
+ memset(bc, 0, sizeof(*bc));
+
+ /* OPA and HFI have a 1-1 mapping */
+ for (i = 0; i < TXE_NUM_DATA_VL; i++)
+ read_one_cm_vl(dd, SEND_CM_CREDIT_VL + (8*i), &bc->vl[i]);
+
+ /* NOTE: assumes that VL* and VL15 CSRs are bit-wise identical */
+ read_one_cm_vl(dd, SEND_CM_CREDIT_VL15, &bc->vl[15]);
+
+ reg = read_csr(dd, SEND_CM_GLOBAL_CREDIT);
+ bc->overall_shared_limit = cpu_to_be16(
+ (reg >> SEND_CM_GLOBAL_CREDIT_SHARED_LIMIT_SHIFT)
+ & SEND_CM_GLOBAL_CREDIT_SHARED_LIMIT_MASK);
+ if (overall_limit)
+ *overall_limit = (reg
+ >> SEND_CM_GLOBAL_CREDIT_TOTAL_CREDIT_LIMIT_SHIFT)
+ & SEND_CM_GLOBAL_CREDIT_TOTAL_CREDIT_LIMIT_MASK;
+ return sizeof(struct buffer_control);
+}
+
+static int get_sc2vlnt(struct hfi1_devdata *dd, struct sc2vlnt *dp)
+{
+ u64 reg;
+ int i;
+
+ /* each register contains 16 SC->VLnt mappings, 4 bits each */
+ reg = read_csr(dd, DCC_CFG_SC_VL_TABLE_15_0);
+ for (i = 0; i < sizeof(u64); i++) {
+ u8 byte = *(((u8 *)®) + i);
+
+ dp->vlnt[2 * i] = byte & 0xf;
+ dp->vlnt[(2 * i) + 1] = (byte & 0xf0) >> 4;
+ }
+
+ reg = read_csr(dd, DCC_CFG_SC_VL_TABLE_31_16);
+ for (i = 0; i < sizeof(u64); i++) {
+ u8 byte = *(((u8 *)®) + i);
+
+ dp->vlnt[16 + (2 * i)] = byte & 0xf;
+ dp->vlnt[16 + (2 * i) + 1] = (byte & 0xf0) >> 4;
+ }
+ return sizeof(struct sc2vlnt);
+}
+
+static void get_vlarb_preempt(struct hfi1_devdata *dd, u32 nelems,
+ struct ib_vl_weight_elem *vl)
+{
+ unsigned int i;
+
+ for (i = 0; i < nelems; i++, vl++) {
+ vl->vl = 0xf;
+ vl->weight = 0;
+ }
+}
+
+static void set_sc2vlnt(struct hfi1_devdata *dd, struct sc2vlnt *dp)
+{
+ write_csr(dd, DCC_CFG_SC_VL_TABLE_15_0,
+ DC_SC_VL_VAL(15_0,
+ 0, dp->vlnt[0] & 0xf,
+ 1, dp->vlnt[1] & 0xf,
+ 2, dp->vlnt[2] & 0xf,
+ 3, dp->vlnt[3] & 0xf,
+ 4, dp->vlnt[4] & 0xf,
+ 5, dp->vlnt[5] & 0xf,
+ 6, dp->vlnt[6] & 0xf,
+ 7, dp->vlnt[7] & 0xf,
+ 8, dp->vlnt[8] & 0xf,
+ 9, dp->vlnt[9] & 0xf,
+ 10, dp->vlnt[10] & 0xf,
+ 11, dp->vlnt[11] & 0xf,
+ 12, dp->vlnt[12] & 0xf,
+ 13, dp->vlnt[13] & 0xf,
+ 14, dp->vlnt[14] & 0xf,
+ 15, dp->vlnt[15] & 0xf));
+ write_csr(dd, DCC_CFG_SC_VL_TABLE_31_16,
+ DC_SC_VL_VAL(31_16,
+ 16, dp->vlnt[16] & 0xf,
+ 17, dp->vlnt[17] & 0xf,
+ 18, dp->vlnt[18] & 0xf,
+ 19, dp->vlnt[19] & 0xf,
+ 20, dp->vlnt[20] & 0xf,
+ 21, dp->vlnt[21] & 0xf,
+ 22, dp->vlnt[22] & 0xf,
+ 23, dp->vlnt[23] & 0xf,
+ 24, dp->vlnt[24] & 0xf,
+ 25, dp->vlnt[25] & 0xf,
+ 26, dp->vlnt[26] & 0xf,
+ 27, dp->vlnt[27] & 0xf,
+ 28, dp->vlnt[28] & 0xf,
+ 29, dp->vlnt[29] & 0xf,
+ 30, dp->vlnt[30] & 0xf,
+ 31, dp->vlnt[31] & 0xf));
+}
+
+static void nonzero_msg(struct hfi1_devdata *dd, int idx, const char *what,
+ u16 limit)
+{
+ if (limit != 0)
+ dd_dev_info(dd, "Invalid %s limit %d on VL %d, ignoring\n",
+ what, (int)limit, idx);
+}
+
+/* change only the shared limit portion of SendCmGLobalCredit */
+static void set_global_shared(struct hfi1_devdata *dd, u16 limit)
+{
+ u64 reg;
+
+ reg = read_csr(dd, SEND_CM_GLOBAL_CREDIT);
+ reg &= ~SEND_CM_GLOBAL_CREDIT_SHARED_LIMIT_SMASK;
+ reg |= (u64)limit << SEND_CM_GLOBAL_CREDIT_SHARED_LIMIT_SHIFT;
+ write_csr(dd, SEND_CM_GLOBAL_CREDIT, reg);
+}
+
+/* change only the total credit limit portion of SendCmGLobalCredit */
+static void set_global_limit(struct hfi1_devdata *dd, u16 limit)
+{
+ u64 reg;
+
+ reg = read_csr(dd, SEND_CM_GLOBAL_CREDIT);
+ reg &= ~SEND_CM_GLOBAL_CREDIT_TOTAL_CREDIT_LIMIT_SMASK;
+ reg |= (u64)limit << SEND_CM_GLOBAL_CREDIT_TOTAL_CREDIT_LIMIT_SHIFT;
+ write_csr(dd, SEND_CM_GLOBAL_CREDIT, reg);
+}
+
+/* set the given per-VL shared limit */
+static void set_vl_shared(struct hfi1_devdata *dd, int vl, u16 limit)
+{
+ u64 reg;
+ u32 addr;
+
+ if (vl < TXE_NUM_DATA_VL)
+ addr = SEND_CM_CREDIT_VL + (8 * vl);
+ else
+ addr = SEND_CM_CREDIT_VL15;
+
+ reg = read_csr(dd, addr);
+ reg &= ~SEND_CM_CREDIT_VL_SHARED_LIMIT_VL_SMASK;
+ reg |= (u64)limit << SEND_CM_CREDIT_VL_SHARED_LIMIT_VL_SHIFT;
+ write_csr(dd, addr, reg);
+}
+
+/* set the given per-VL dedicated limit */
+static void set_vl_dedicated(struct hfi1_devdata *dd, int vl, u16 limit)
+{
+ u64 reg;
+ u32 addr;
+
+ if (vl < TXE_NUM_DATA_VL)
+ addr = SEND_CM_CREDIT_VL + (8 * vl);
+ else
+ addr = SEND_CM_CREDIT_VL15;
+
+ reg = read_csr(dd, addr);
+ reg &= ~SEND_CM_CREDIT_VL_DEDICATED_LIMIT_VL_SMASK;
+ reg |= (u64)limit << SEND_CM_CREDIT_VL_DEDICATED_LIMIT_VL_SHIFT;
+ write_csr(dd, addr, reg);
+}
+
+/* spin until the given per-VL status mask bits clear */
+static void wait_for_vl_status_clear(struct hfi1_devdata *dd, u64 mask,
+ const char *which)
+{
+ unsigned long timeout;
+ u64 reg;
+
+ timeout = jiffies + msecs_to_jiffies(VL_STATUS_CLEAR_TIMEOUT);
+ while (1) {
+ reg = read_csr(dd, SEND_CM_CREDIT_USED_STATUS) & mask;
+
+ if (reg == 0)
+ return; /* success */
+ if (time_after(jiffies, timeout))
+ break; /* timed out */
+ udelay(1);
+ }
+
+ dd_dev_err(dd,
+ "%s credit change status not clearing after %dms, mask 0x%llx, not clear 0x%llx\n",
+ which, VL_STATUS_CLEAR_TIMEOUT, mask, reg);
+ /*
+ * If this occurs, it is likely there was a credit loss on the link.
+ * The only recovery from that is a link bounce.
+ */
+ dd_dev_err(dd,
+ "Continuing anyway. A credit loss may occur. Suggest a link bounce\n");
+}
+
+/*
+ * The number of credits on the VLs may be changed while everything
+ * is "live", but the following algorithm must be followed due to
+ * how the hardware is actually implemented. In particular,
+ * Return_Credit_Status[] is the only correct status check.
+ *
+ * if (reducing Global_Shared_Credit_Limit or any shared limit changing)
+ * set Global_Shared_Credit_Limit = 0
+ * use_all_vl = 1
+ * mask0 = all VLs that are changing either dedicated or shared limits
+ * set Shared_Limit[mask0] = 0
+ * spin until Return_Credit_Status[use_all_vl ? all VL : mask0] == 0
+ * if (changing any dedicated limit)
+ * mask1 = all VLs that are lowering dedicated limits
+ * lower Dedicated_Limit[mask1]
+ * spin until Return_Credit_Status[mask1] == 0
+ * raise Dedicated_Limits
+ * raise Shared_Limits
+ * raise Global_Shared_Credit_Limit
+ *
+ * lower = if the new limit is lower, set the limit to the new value
+ * raise = if the new limit is higher than the current value (may be changed
+ * earlier in the algorithm), set the new limit to the new value
+ */
+static int set_buffer_control(struct hfi1_devdata *dd,
+ struct buffer_control *new_bc)
+{
+ u64 changing_mask, ld_mask, stat_mask;
+ int change_count;
+ int i, use_all_mask;
+ int this_shared_changing;
+ /*
+ * A0: add the variable any_shared_limit_changing below and in the
+ * algorithm above. If removing A0 support, it can be removed.
+ */
+ int any_shared_limit_changing;
+ struct buffer_control cur_bc;
+ u8 changing[OPA_MAX_VLS];
+ u8 lowering_dedicated[OPA_MAX_VLS];
+ u16 cur_total;
+ u32 new_total = 0;
+ const u64 all_mask =
+ SEND_CM_CREDIT_USED_STATUS_VL0_RETURN_CREDIT_STATUS_SMASK
+ | SEND_CM_CREDIT_USED_STATUS_VL1_RETURN_CREDIT_STATUS_SMASK
+ | SEND_CM_CREDIT_USED_STATUS_VL2_RETURN_CREDIT_STATUS_SMASK
+ | SEND_CM_CREDIT_USED_STATUS_VL3_RETURN_CREDIT_STATUS_SMASK
+ | SEND_CM_CREDIT_USED_STATUS_VL4_RETURN_CREDIT_STATUS_SMASK
+ | SEND_CM_CREDIT_USED_STATUS_VL5_RETURN_CREDIT_STATUS_SMASK
+ | SEND_CM_CREDIT_USED_STATUS_VL6_RETURN_CREDIT_STATUS_SMASK
+ | SEND_CM_CREDIT_USED_STATUS_VL7_RETURN_CREDIT_STATUS_SMASK
+ | SEND_CM_CREDIT_USED_STATUS_VL15_RETURN_CREDIT_STATUS_SMASK;
+
+#define valid_vl(idx) ((idx) < TXE_NUM_DATA_VL || (idx) == 15)
+#define NUM_USABLE_VLS 16 /* look at VL15 and less */
+
+
+ /* find the new total credits, do sanity check on unused VLs */
+ for (i = 0; i < OPA_MAX_VLS; i++) {
+ if (valid_vl(i)) {
+ new_total += be16_to_cpu(new_bc->vl[i].dedicated);
+ continue;
+ }
+ nonzero_msg(dd, i, "dedicated",
+ be16_to_cpu(new_bc->vl[i].dedicated));
+ nonzero_msg(dd, i, "shared",
+ be16_to_cpu(new_bc->vl[i].shared));
+ new_bc->vl[i].dedicated = 0;
+ new_bc->vl[i].shared = 0;
+ }
+ new_total += be16_to_cpu(new_bc->overall_shared_limit);
+ if (new_total > (u32)dd->link_credits)
+ return -EINVAL;
+ /* fetch the current values */
+ get_buffer_control(dd, &cur_bc, &cur_total);
+
+ /*
+ * Create the masks we will use.
+ */
+ memset(changing, 0, sizeof(changing));
+ memset(lowering_dedicated, 0, sizeof(lowering_dedicated));
+ /* NOTE: Assumes that the individual VL bits are adjacent and in
+ increasing order */
+ stat_mask =
+ SEND_CM_CREDIT_USED_STATUS_VL0_RETURN_CREDIT_STATUS_SMASK;
+ changing_mask = 0;
+ ld_mask = 0;
+ change_count = 0;
+ any_shared_limit_changing = 0;
+ for (i = 0; i < NUM_USABLE_VLS; i++, stat_mask <<= 1) {
+ if (!valid_vl(i))
+ continue;
+ this_shared_changing = new_bc->vl[i].shared
+ != cur_bc.vl[i].shared;
+ if (this_shared_changing)
+ any_shared_limit_changing = 1;
+ if (new_bc->vl[i].dedicated != cur_bc.vl[i].dedicated
+ || this_shared_changing) {
+ changing[i] = 1;
+ changing_mask |= stat_mask;
+ change_count++;
+ }
+ if (be16_to_cpu(new_bc->vl[i].dedicated) <
+ be16_to_cpu(cur_bc.vl[i].dedicated)) {
+ lowering_dedicated[i] = 1;
+ ld_mask |= stat_mask;
+ }
+ }
+
+ /* bracket the credit change with a total adjustment */
+ if (new_total > cur_total)
+ set_global_limit(dd, new_total);
+
+ /*
+ * Start the credit change algorithm.
+ */
+ use_all_mask = 0;
+ if ((be16_to_cpu(new_bc->overall_shared_limit) <
+ be16_to_cpu(cur_bc.overall_shared_limit))
+ || (is_a0(dd) && any_shared_limit_changing)) {
+ set_global_shared(dd, 0);
+ cur_bc.overall_shared_limit = 0;
+ use_all_mask = 1;
+ }
+
+ for (i = 0; i < NUM_USABLE_VLS; i++) {
+ if (!valid_vl(i))
+ continue;
+
+ if (changing[i]) {
+ set_vl_shared(dd, i, 0);
+ cur_bc.vl[i].shared = 0;
+ }
+ }
+
+ wait_for_vl_status_clear(dd, use_all_mask ? all_mask : changing_mask,
+ "shared");
+
+ if (change_count > 0) {
+ for (i = 0; i < NUM_USABLE_VLS; i++) {
+ if (!valid_vl(i))
+ continue;
+
+ if (lowering_dedicated[i]) {
+ set_vl_dedicated(dd, i,
+ be16_to_cpu(new_bc->vl[i].dedicated));
+ cur_bc.vl[i].dedicated =
+ new_bc->vl[i].dedicated;
+ }
+ }
+
+ wait_for_vl_status_clear(dd, ld_mask, "dedicated");
+
+ /* now raise all dedicated that are going up */
+ for (i = 0; i < NUM_USABLE_VLS; i++) {
+ if (!valid_vl(i))
+ continue;
+
+ if (be16_to_cpu(new_bc->vl[i].dedicated) >
+ be16_to_cpu(cur_bc.vl[i].dedicated))
+ set_vl_dedicated(dd, i,
+ be16_to_cpu(new_bc->vl[i].dedicated));
+ }
+ }
+
+ /* next raise all shared that are going up */
+ for (i = 0; i < NUM_USABLE_VLS; i++) {
+ if (!valid_vl(i))
+ continue;
+
+ if (be16_to_cpu(new_bc->vl[i].shared) >
+ be16_to_cpu(cur_bc.vl[i].shared))
+ set_vl_shared(dd, i, be16_to_cpu(new_bc->vl[i].shared));
+ }
+
+ /* finally raise the global shared */
+ if (be16_to_cpu(new_bc->overall_shared_limit) >
+ be16_to_cpu(cur_bc.overall_shared_limit))
+ set_global_shared(dd,
+ be16_to_cpu(new_bc->overall_shared_limit));
+
+ /* bracket the credit change with a total adjustment */
+ if (new_total < cur_total)
+ set_global_limit(dd, new_total);
+ return 0;
+}
+
+/*
+ * Read the given fabric manager table. Return the size of the
+ * table (in bytes) on success, and a negative error code on
+ * failure.
+ */
+int fm_get_table(struct hfi1_pportdata *ppd, int which, void *t)
+
+{
+ int size;
+ struct vl_arb_cache *vlc;
+
+ switch (which) {
+ case FM_TBL_VL_HIGH_ARB:
+ size = 256;
+ /*
+ * OPA specifies 128 elements (of 2 bytes each), though
+ * HFI supports only 16 elements in h/w.
+ */
+ vlc = vl_arb_lock_cache(ppd, HI_PRIO_TABLE);
+ vl_arb_get_cache(vlc, t);
+ vl_arb_unlock_cache(ppd, HI_PRIO_TABLE);
+ break;
+ case FM_TBL_VL_LOW_ARB:
+ size = 256;
+ /*
+ * OPA specifies 128 elements (of 2 bytes each), though
+ * HFI supports only 16 elements in h/w.
+ */
+ vlc = vl_arb_lock_cache(ppd, LO_PRIO_TABLE);
+ vl_arb_get_cache(vlc, t);
+ vl_arb_unlock_cache(ppd, LO_PRIO_TABLE);
+ break;
+ case FM_TBL_BUFFER_CONTROL:
+ size = get_buffer_control(ppd->dd, t, NULL);
+ break;
+ case FM_TBL_SC2VLNT:
+ size = get_sc2vlnt(ppd->dd, t);
+ break;
+ case FM_TBL_VL_PREEMPT_ELEMS:
+ size = 256;
+ /* OPA specifies 128 elements, of 2 bytes each */
+ get_vlarb_preempt(ppd->dd, OPA_MAX_VLS, t);
+ break;
+ case FM_TBL_VL_PREEMPT_MATRIX:
+ size = 256;
+ /*
+ * OPA specifies that this is the same size as the VL
+ * arbitration tables (i.e., 256 bytes).
+ */
+ break;
+ default:
+ return -EINVAL;
+ }
+ return size;
+}
+
+/*
+ * Write the given fabric manager table.
+ */
+int fm_set_table(struct hfi1_pportdata *ppd, int which, void *t)
+{
+ int ret = 0;
+ struct vl_arb_cache *vlc;
+
+ switch (which) {
+ case FM_TBL_VL_HIGH_ARB:
+ vlc = vl_arb_lock_cache(ppd, HI_PRIO_TABLE);
+ if (vl_arb_match_cache(vlc, t)) {
+ vl_arb_unlock_cache(ppd, HI_PRIO_TABLE);
+ break;
+ }
+ vl_arb_set_cache(vlc, t);
+ vl_arb_unlock_cache(ppd, HI_PRIO_TABLE);
+ ret = set_vl_weights(ppd, SEND_HIGH_PRIORITY_LIST,
+ VL_ARB_HIGH_PRIO_TABLE_SIZE, t);
+ break;
+ case FM_TBL_VL_LOW_ARB:
+ vlc = vl_arb_lock_cache(ppd, LO_PRIO_TABLE);
+ if (vl_arb_match_cache(vlc, t)) {
+ vl_arb_unlock_cache(ppd, LO_PRIO_TABLE);
+ break;
+ }
+ vl_arb_set_cache(vlc, t);
+ vl_arb_unlock_cache(ppd, LO_PRIO_TABLE);
+ ret = set_vl_weights(ppd, SEND_LOW_PRIORITY_LIST,
+ VL_ARB_LOW_PRIO_TABLE_SIZE, t);
+ break;
+ case FM_TBL_BUFFER_CONTROL:
+ ret = set_buffer_control(ppd->dd, t);
+ break;
+ case FM_TBL_SC2VLNT:
+ set_sc2vlnt(ppd->dd, t);
+ break;
+ default:
+ ret = -EINVAL;
+ }
+ return ret;
+}
+
+/*
+ * Disable all data VLs.
+ *
+ * Return 0 if disabled, non-zero if the VLs cannot be disabled.
+ */
+static int disable_data_vls(struct hfi1_devdata *dd)
+{
+ if (is_a0(dd))
+ return 1;
+
+ pio_send_control(dd, PSC_DATA_VL_DISABLE);
+
+ return 0;
+}
+
+/*
+ * open_fill_data_vls() - the counterpart to stop_drain_data_vls().
+ * Just re-enables all data VLs (the "fill" part happens
+ * automatically - the name was chosen for symmetry with
+ * stop_drain_data_vls()).
+ *
+ * Return 0 if successful, non-zero if the VLs cannot be enabled.
+ */
+int open_fill_data_vls(struct hfi1_devdata *dd)
+{
+ if (is_a0(dd))
+ return 1;
+
+ pio_send_control(dd, PSC_DATA_VL_ENABLE);
+
+ return 0;
+}
+
+/*
+ * drain_data_vls() - assumes that disable_data_vls() has been called,
+ * wait for occupancy (of per-VL FIFOs) for all contexts, and SDMA
+ * engines to drop to 0.
+ */
+static void drain_data_vls(struct hfi1_devdata *dd)
+{
+ sc_wait(dd);
+ sdma_wait(dd);
+ pause_for_credit_return(dd);
+}
+
+/*
+ * stop_drain_data_vls() - disable, then drain all per-VL fifos.
+ *
+ * Use open_fill_data_vls() to resume using data VLs. This pair is
+ * meant to be used like this:
+ *
+ * stop_drain_data_vls(dd);
+ * // do things with per-VL resources
+ * open_fill_data_vls(dd);
+ */
+int stop_drain_data_vls(struct hfi1_devdata *dd)
+{
+ int ret;
+
+ ret = disable_data_vls(dd);
+ if (ret == 0)
+ drain_data_vls(dd);
+
+ return ret;
+}
+
+/*
+ * Convert a nanosecond time to a cclock count. No matter how slow
+ * the cclock, a non-zero ns will always have a non-zero result.
+ */
+u32 ns_to_cclock(struct hfi1_devdata *dd, u32 ns)
+{
+ u32 cclocks;
+
+ if (dd->icode == ICODE_FPGA_EMULATION)
+ cclocks = (ns * 1000) / FPGA_CCLOCK_PS;
+ else /* simulation pretends to be ASIC */
+ cclocks = (ns * 1000) / ASIC_CCLOCK_PS;
+ if (ns && !cclocks) /* if ns nonzero, must be at least 1 */
+ cclocks = 1;
+ return cclocks;
+}
+
+/*
+ * Convert a cclock count to nanoseconds. Not matter how slow
+ * the cclock, a non-zero cclocks will always have a non-zero result.
+ */
+u32 cclock_to_ns(struct hfi1_devdata *dd, u32 cclocks)
+{
+ u32 ns;
+
+ if (dd->icode == ICODE_FPGA_EMULATION)
+ ns = (cclocks * FPGA_CCLOCK_PS) / 1000;
+ else /* simulation pretends to be ASIC */
+ ns = (cclocks * ASIC_CCLOCK_PS) / 1000;
+ if (cclocks && !ns)
+ ns = 1;
+ return ns;
+}
+
+/*
+ * Dynamically adjust the receive interrupt timeout for a context based on
+ * incoming packet rate.
+ *
+ * NOTE: Dynamic adjustment does not allow rcv_intr_count to be zero.
+ */
+static void adjust_rcv_timeout(struct hfi1_ctxtdata *rcd, u32 npkts)
+{
+ struct hfi1_devdata *dd = rcd->dd;
+ u32 timeout = rcd->rcvavail_timeout;
+
+ /*
+ * This algorithm doubles or halves the timeout depending on whether
+ * the number of packets received in this interrupt were less than or
+ * greater equal the interrupt count.
+ *
+ * The calculations below do not allow a steady state to be achieved.
+ * Only at the endpoints it is possible to have an unchanging
+ * timeout.
+ */
+ if (npkts < rcv_intr_count) {
+ /*
+ * Not enough packets arrived before the timeout, adjust
+ * timeout downward.
+ */
+ if (timeout < 2) /* already at minimum? */
+ return;
+ timeout >>= 1;
+ } else {
+ /*
+ * More than enough packets arrived before the timeout, adjust
+ * timeout upward.
+ */
+ if (timeout >= dd->rcv_intr_timeout_csr) /* already at max? */
+ return;
+ timeout = min(timeout << 1, dd->rcv_intr_timeout_csr);
+ }
+
+ rcd->rcvavail_timeout = timeout;
+ /* timeout cannot be larger than rcv_intr_timeout_csr which has already
+ been verified to be in range */
+ write_kctxt_csr(dd, rcd->ctxt, RCV_AVAIL_TIME_OUT,
+ (u64)timeout << RCV_AVAIL_TIME_OUT_TIME_OUT_RELOAD_SHIFT);
+}
+
+void update_usrhead(struct hfi1_ctxtdata *rcd, u32 hd, u32 updegr, u32 egrhd,
+ u32 intr_adjust, u32 npkts)
+{
+ struct hfi1_devdata *dd = rcd->dd;
+ u64 reg;
+ u32 ctxt = rcd->ctxt;
+
+ /*
+ * Need to write timeout register before updating RcvHdrHead to ensure
+ * that a new value is used when the HW decides to restart counting.
+ */
+ if (intr_adjust)
+ adjust_rcv_timeout(rcd, npkts);
+ if (updegr) {
+ reg = (egrhd & RCV_EGR_INDEX_HEAD_HEAD_MASK)
+ << RCV_EGR_INDEX_HEAD_HEAD_SHIFT;
+ write_uctxt_csr(dd, ctxt, RCV_EGR_INDEX_HEAD, reg);
+ }
+ mmiowb();
+ reg = ((u64)rcv_intr_count << RCV_HDR_HEAD_COUNTER_SHIFT) |
+ (((u64)hd & RCV_HDR_HEAD_HEAD_MASK)
+ << RCV_HDR_HEAD_HEAD_SHIFT);
+ write_uctxt_csr(dd, ctxt, RCV_HDR_HEAD, reg);
+ mmiowb();
+}
+
+u32 hdrqempty(struct hfi1_ctxtdata *rcd)
+{
+ u32 head, tail;
+
+ head = (read_uctxt_csr(rcd->dd, rcd->ctxt, RCV_HDR_HEAD)
+ & RCV_HDR_HEAD_HEAD_SMASK) >> RCV_HDR_HEAD_HEAD_SHIFT;
+
+ if (rcd->rcvhdrtail_kvaddr)
+ tail = get_rcvhdrtail(rcd);
+ else
+ tail = read_uctxt_csr(rcd->dd, rcd->ctxt, RCV_HDR_TAIL);
+
+ return head == tail;
+}
+
+/*
+ * Context Control and Receive Array encoding for buffer size:
+ * 0x0 invalid
+ * 0x1 4 KB
+ * 0x2 8 KB
+ * 0x3 16 KB
+ * 0x4 32 KB
+ * 0x5 64 KB
+ * 0x6 128 KB
+ * 0x7 256 KB
+ * 0x8 512 KB (Receive Array only)
+ * 0x9 1 MB (Receive Array only)
+ * 0xa 2 MB (Receive Array only)
+ *
+ * 0xB-0xF - reserved (Receive Array only)
+ *
+ *
+ * This routine assumes that the value has already been sanity checked.
+ */
+static u32 encoded_size(u32 size)
+{
+ switch (size) {
+ case 4*1024: return 0x1;
+ case 8*1024: return 0x2;
+ case 16*1024: return 0x3;
+ case 32*1024: return 0x4;
+ case 64*1024: return 0x5;
+ case 128*1024: return 0x6;
+ case 256*1024: return 0x7;
+ case 512*1024: return 0x8;
+ case 1*1024*1024: return 0x9;
+ case 2*1024*1024: return 0xa;
+ }
+ return 0x1; /* if invalid, go with the minimum size */
+}
+
+void hfi1_rcvctrl(struct hfi1_devdata *dd, unsigned int op, int ctxt)
+{
+ struct hfi1_ctxtdata *rcd;
+ u64 rcvctrl, reg;
+ int did_enable = 0;
+
+ rcd = dd->rcd[ctxt];
+ if (!rcd)
+ return;
+
+ hfi1_cdbg(RCVCTRL, "ctxt %d op 0x%x", ctxt, op);
+
+ rcvctrl = read_kctxt_csr(dd, ctxt, RCV_CTXT_CTRL);
+ /* if the context already enabled, don't do the extra steps */
+ if ((op & HFI1_RCVCTRL_CTXT_ENB)
+ && !(rcvctrl & RCV_CTXT_CTRL_ENABLE_SMASK)) {
+ /* reset the tail and hdr addresses, and sequence count */
+ write_kctxt_csr(dd, ctxt, RCV_HDR_ADDR,
+ rcd->rcvhdrq_phys);
+ if (HFI1_CAP_KGET_MASK(rcd->flags, DMA_RTAIL))
+ write_kctxt_csr(dd, ctxt, RCV_HDR_TAIL_ADDR,
+ rcd->rcvhdrqtailaddr_phys);
+ rcd->seq_cnt = 1;
+
+ /* reset the cached receive header queue head value */
+ rcd->head = 0;
+
+ /*
+ * Zero the receive header queue so we don't get false
+ * positives when checking the sequence number. The
+ * sequence numbers could land exactly on the same spot.
+ * E.g. a rcd restart before the receive header wrapped.
+ */
+ memset(rcd->rcvhdrq, 0, rcd->rcvhdrq_size);
+
+ /* starting timeout */
+ rcd->rcvavail_timeout = dd->rcv_intr_timeout_csr;
+
+ /* enable the context */
+ rcvctrl |= RCV_CTXT_CTRL_ENABLE_SMASK;
+
+ /* clean the egr buffer size first */
+ rcvctrl &= ~RCV_CTXT_CTRL_EGR_BUF_SIZE_SMASK;
+ rcvctrl |= ((u64)encoded_size(rcd->egrbufs.rcvtid_size)
+ & RCV_CTXT_CTRL_EGR_BUF_SIZE_MASK)
+ << RCV_CTXT_CTRL_EGR_BUF_SIZE_SHIFT;
+
+ /* zero RcvHdrHead - set RcvHdrHead.Counter after enable */
+ write_uctxt_csr(dd, ctxt, RCV_HDR_HEAD, 0);
+ did_enable = 1;
+
+ /* zero RcvEgrIndexHead */
+ write_uctxt_csr(dd, ctxt, RCV_EGR_INDEX_HEAD, 0);
+
+ /* set eager count and base index */
+ reg = (((u64)(rcd->egrbufs.alloced >> RCV_SHIFT)
+ & RCV_EGR_CTRL_EGR_CNT_MASK)
+ << RCV_EGR_CTRL_EGR_CNT_SHIFT) |
+ (((rcd->eager_base >> RCV_SHIFT)
+ & RCV_EGR_CTRL_EGR_BASE_INDEX_MASK)
+ << RCV_EGR_CTRL_EGR_BASE_INDEX_SHIFT);
+ write_kctxt_csr(dd, ctxt, RCV_EGR_CTRL, reg);
+
+ /*
+ * Set TID (expected) count and base index.
+ * rcd->expected_count is set to individual RcvArray entries,
+ * not pairs, and the CSR takes a pair-count in groups of
+ * four, so divide by 8.
+ */
+ reg = (((rcd->expected_count >> RCV_SHIFT)
+ & RCV_TID_CTRL_TID_PAIR_CNT_MASK)
+ << RCV_TID_CTRL_TID_PAIR_CNT_SHIFT) |
+ (((rcd->expected_base >> RCV_SHIFT)
+ & RCV_TID_CTRL_TID_BASE_INDEX_MASK)
+ << RCV_TID_CTRL_TID_BASE_INDEX_SHIFT);
+ write_kctxt_csr(dd, ctxt, RCV_TID_CTRL, reg);
+ if (ctxt == VL15CTXT)
+ write_csr(dd, RCV_VL15, VL15CTXT);
+ }
+ if (op & HFI1_RCVCTRL_CTXT_DIS) {
+ write_csr(dd, RCV_VL15, 0);
+ rcvctrl &= ~RCV_CTXT_CTRL_ENABLE_SMASK;
+ }
+ if (op & HFI1_RCVCTRL_INTRAVAIL_ENB)
+ rcvctrl |= RCV_CTXT_CTRL_INTR_AVAIL_SMASK;
+ if (op & HFI1_RCVCTRL_INTRAVAIL_DIS)
+ rcvctrl &= ~RCV_CTXT_CTRL_INTR_AVAIL_SMASK;
+ if (op & HFI1_RCVCTRL_TAILUPD_ENB && rcd->rcvhdrqtailaddr_phys)
+ rcvctrl |= RCV_CTXT_CTRL_TAIL_UPD_SMASK;
+ if (op & HFI1_RCVCTRL_TAILUPD_DIS)
+ rcvctrl &= ~RCV_CTXT_CTRL_TAIL_UPD_SMASK;
+ if (op & HFI1_RCVCTRL_TIDFLOW_ENB)
+ rcvctrl |= RCV_CTXT_CTRL_TID_FLOW_ENABLE_SMASK;
+ if (op & HFI1_RCVCTRL_TIDFLOW_DIS)
+ rcvctrl &= ~RCV_CTXT_CTRL_TID_FLOW_ENABLE_SMASK;
+ if (op & HFI1_RCVCTRL_ONE_PKT_EGR_ENB) {
+ /* In one-packet-per-eager mode, the size comes from
+ the RcvArray entry. */
+ rcvctrl &= ~RCV_CTXT_CTRL_EGR_BUF_SIZE_SMASK;
+ rcvctrl |= RCV_CTXT_CTRL_ONE_PACKET_PER_EGR_BUFFER_SMASK;
+ }
+ if (op & HFI1_RCVCTRL_ONE_PKT_EGR_DIS)
+ rcvctrl &= ~RCV_CTXT_CTRL_ONE_PACKET_PER_EGR_BUFFER_SMASK;
+ if (op & HFI1_RCVCTRL_NO_RHQ_DROP_ENB)
+ rcvctrl |= RCV_CTXT_CTRL_DONT_DROP_RHQ_FULL_SMASK;
+ if (op & HFI1_RCVCTRL_NO_RHQ_DROP_DIS)
+ rcvctrl &= ~RCV_CTXT_CTRL_DONT_DROP_RHQ_FULL_SMASK;
+ if (op & HFI1_RCVCTRL_NO_EGR_DROP_ENB)
+ rcvctrl |= RCV_CTXT_CTRL_DONT_DROP_EGR_FULL_SMASK;
+ if (op & HFI1_RCVCTRL_NO_EGR_DROP_DIS)
+ rcvctrl &= ~RCV_CTXT_CTRL_DONT_DROP_EGR_FULL_SMASK;
+ rcd->rcvctrl = rcvctrl;
+ hfi1_cdbg(RCVCTRL, "ctxt %d rcvctrl 0x%llx\n", ctxt, rcvctrl);
+ write_kctxt_csr(dd, ctxt, RCV_CTXT_CTRL, rcd->rcvctrl);
+
+ /* work around sticky RcvCtxtStatus.BlockedRHQFull */
+ if (did_enable
+ && (rcvctrl & RCV_CTXT_CTRL_DONT_DROP_RHQ_FULL_SMASK)) {
+ reg = read_kctxt_csr(dd, ctxt, RCV_CTXT_STATUS);
+ if (reg != 0) {
+ dd_dev_info(dd, "ctxt %d status %lld (blocked)\n",
+ ctxt, reg);
+ read_uctxt_csr(dd, ctxt, RCV_HDR_HEAD);
+ write_uctxt_csr(dd, ctxt, RCV_HDR_HEAD, 0x10);
+ write_uctxt_csr(dd, ctxt, RCV_HDR_HEAD, 0x00);
+ read_uctxt_csr(dd, ctxt, RCV_HDR_HEAD);
+ reg = read_kctxt_csr(dd, ctxt, RCV_CTXT_STATUS);
+ dd_dev_info(dd, "ctxt %d status %lld (%s blocked)\n",
+ ctxt, reg, reg == 0 ? "not" : "still");
+ }
+ }
+
+ if (did_enable) {
+ /*
+ * The interrupt timeout and count must be set after
+ * the context is enabled to take effect.
+ */
+ /* set interrupt timeout */
+ write_kctxt_csr(dd, ctxt, RCV_AVAIL_TIME_OUT,
+ (u64)rcd->rcvavail_timeout <<
+ RCV_AVAIL_TIME_OUT_TIME_OUT_RELOAD_SHIFT);
+
+ /* set RcvHdrHead.Counter, zero RcvHdrHead.Head (again) */
+ reg = (u64)rcv_intr_count << RCV_HDR_HEAD_COUNTER_SHIFT;
+ write_uctxt_csr(dd, ctxt, RCV_HDR_HEAD, reg);
+ }
+
+ if (op & (HFI1_RCVCTRL_TAILUPD_DIS | HFI1_RCVCTRL_CTXT_DIS))
+ /*
+ * If the context has been disabled and the Tail Update has
+ * been cleared, clear the RCV_HDR_TAIL_ADDR CSR so
+ * it doesn't contain an address that is invalid.
+ */
+ write_kctxt_csr(dd, ctxt, RCV_HDR_TAIL_ADDR, 0);
+}
+
+u32 hfi1_read_cntrs(struct hfi1_devdata *dd, loff_t pos, char **namep,
+ u64 **cntrp)
+{
+ int ret;
+ u64 val = 0;
+
+ if (namep) {
+ ret = dd->cntrnameslen;
+ if (pos != 0) {
+ dd_dev_err(dd, "read_cntrs does not support indexing");
+ return 0;
+ }
+ *namep = dd->cntrnames;
+ } else {
+ const struct cntr_entry *entry;
+ int i, j;
+
+ ret = (dd->ndevcntrs) * sizeof(u64);
+ if (pos != 0) {
+ dd_dev_err(dd, "read_cntrs does not support indexing");
+ return 0;
+ }
+
+ /* Get the start of the block of counters */
+ *cntrp = dd->cntrs;
+
+ /*
+ * Now go and fill in each counter in the block.
+ */
+ for (i = 0; i < DEV_CNTR_LAST; i++) {
+ entry = &dev_cntrs[i];
+ hfi1_cdbg(CNTR, "reading %s", entry->name);
+ if (entry->flags & CNTR_DISABLED) {
+ /* Nothing */
+ hfi1_cdbg(CNTR, "\tDisabled\n");
+ } else {
+ if (entry->flags & CNTR_VL) {
+ hfi1_cdbg(CNTR, "\tPer VL\n");
+ for (j = 0; j < C_VL_COUNT; j++) {
+ val = entry->rw_cntr(entry,
+ dd, j,
+ CNTR_MODE_R,
+ 0);
+ hfi1_cdbg(
+ CNTR,
+ "\t\tRead 0x%llx for %d\n",
+ val, j);
+ dd->cntrs[entry->offset + j] =
+ val;
+ }
+ } else {
+ val = entry->rw_cntr(entry, dd,
+ CNTR_INVALID_VL,
+ CNTR_MODE_R, 0);
+ dd->cntrs[entry->offset] = val;
+ hfi1_cdbg(CNTR, "\tRead 0x%llx", val);
+ }
+ }
+ }
+ }
+ return ret;
+}
+
+/*
+ * Used by sysfs to create files for hfi stats to read
+ */
+u32 hfi1_read_portcntrs(struct hfi1_devdata *dd, loff_t pos, u32 port,
+ char **namep, u64 **cntrp)
+{
+ int ret;
+ u64 val = 0;
+
+ if (namep) {
+ ret = dd->portcntrnameslen;
+ if (pos != 0) {
+ dd_dev_err(dd, "index not supported");
+ return 0;
+ }
+ *namep = dd->portcntrnames;
+ } else {
+ const struct cntr_entry *entry;
+ struct hfi1_pportdata *ppd;
+ int i, j;
+
+ ret = (dd->nportcntrs) * sizeof(u64);
+ if (pos != 0) {
+ dd_dev_err(dd, "indexing not supported");
+ return 0;
+ }
+ ppd = (struct hfi1_pportdata *)(dd + 1 + port);
+ *cntrp = ppd->cntrs;
+
+ for (i = 0; i < PORT_CNTR_LAST; i++) {
+ entry = &port_cntrs[i];
+ hfi1_cdbg(CNTR, "reading %s", entry->name);
+ if (entry->flags & CNTR_DISABLED) {
+ /* Nothing */
+ hfi1_cdbg(CNTR, "\tDisabled\n");
+ continue;
+ }
+
+ if (entry->flags & CNTR_VL) {
+ hfi1_cdbg(CNTR, "\tPer VL");
+ for (j = 0; j < C_VL_COUNT; j++) {
+ val = entry->rw_cntr(entry, ppd, j,
+ CNTR_MODE_R,
+ 0);
+ hfi1_cdbg(
+ CNTR,
+ "\t\tRead 0x%llx for %d",
+ val, j);
+ ppd->cntrs[entry->offset + j] = val;
+ }
+ } else {
+ val = entry->rw_cntr(entry, ppd,
+ CNTR_INVALID_VL,
+ CNTR_MODE_R,
+ 0);
+ ppd->cntrs[entry->offset] = val;
+ hfi1_cdbg(CNTR, "\tRead 0x%llx", val);
+ }
+ }
+ }
+ return ret;
+}
+
+static void free_cntrs(struct hfi1_devdata *dd)
+{
+ struct hfi1_pportdata *ppd;
+ int i;
+
+ if (dd->synth_stats_timer.data)
+ del_timer_sync(&dd->synth_stats_timer);
+ dd->synth_stats_timer.data = 0;
+ ppd = (struct hfi1_pportdata *)(dd + 1);
+ for (i = 0; i < dd->num_pports; i++, ppd++) {
+ kfree(ppd->cntrs);
+ kfree(ppd->scntrs);
+ free_percpu(ppd->ibport_data.rc_acks);
+ free_percpu(ppd->ibport_data.rc_qacks);
+ free_percpu(ppd->ibport_data.rc_delayed_comp);
+ ppd->cntrs = NULL;
+ ppd->scntrs = NULL;
+ ppd->ibport_data.rc_acks = NULL;
+ ppd->ibport_data.rc_qacks = NULL;
+ ppd->ibport_data.rc_delayed_comp = NULL;
+ }
+ kfree(dd->portcntrnames);
+ dd->portcntrnames = NULL;
+ kfree(dd->cntrs);
+ dd->cntrs = NULL;
+ kfree(dd->scntrs);
+ dd->scntrs = NULL;
+ kfree(dd->cntrnames);
+ dd->cntrnames = NULL;
+}
+
+#define CNTR_MAX 0xFFFFFFFFFFFFFFFFULL
+#define CNTR_32BIT_MAX 0x00000000FFFFFFFF
+
+static u64 read_dev_port_cntr(struct hfi1_devdata *dd, struct cntr_entry *entry,
+ u64 *psval, void *context, int vl)
+{
+ u64 val;
+ u64 sval = *psval;
+
+ if (entry->flags & CNTR_DISABLED) {
+ dd_dev_err(dd, "Counter %s not enabled", entry->name);
+ return 0;
+ }
+
+ hfi1_cdbg(CNTR, "cntr: %s vl %d psval 0x%llx", entry->name, vl, *psval);
+
+ val = entry->rw_cntr(entry, context, vl, CNTR_MODE_R, 0);
+
+ /* If its a synthetic counter there is more work we need to do */
+ if (entry->flags & CNTR_SYNTH) {
+ if (sval == CNTR_MAX) {
+ /* No need to read already saturated */
+ return CNTR_MAX;
+ }
+
+ if (entry->flags & CNTR_32BIT) {
+ /* 32bit counters can wrap multiple times */
+ u64 upper = sval >> 32;
+ u64 lower = (sval << 32) >> 32;
+
+ if (lower > val) { /* hw wrapped */
+ if (upper == CNTR_32BIT_MAX)
+ val = CNTR_MAX;
+ else
+ upper++;
+ }
+
+ if (val != CNTR_MAX)
+ val = (upper << 32) | val;
+
+ } else {
+ /* If we rolled we are saturated */
+ if ((val < sval) || (val > CNTR_MAX))
+ val = CNTR_MAX;
+ }
+ }
+
+ *psval = val;
+
+ hfi1_cdbg(CNTR, "\tNew val=0x%llx", val);
+
+ return val;
+}
+
+static u64 write_dev_port_cntr(struct hfi1_devdata *dd,
+ struct cntr_entry *entry,
+ u64 *psval, void *context, int vl, u64 data)
+{
+ u64 val;
+
+ if (entry->flags & CNTR_DISABLED) {
+ dd_dev_err(dd, "Counter %s not enabled", entry->name);
+ return 0;
+ }
+
+ hfi1_cdbg(CNTR, "cntr: %s vl %d psval 0x%llx", entry->name, vl, *psval);
+
+ if (entry->flags & CNTR_SYNTH) {
+ *psval = data;
+ if (entry->flags & CNTR_32BIT) {
+ val = entry->rw_cntr(entry, context, vl, CNTR_MODE_W,
+ (data << 32) >> 32);
+ val = data; /* return the full 64bit value */
+ } else {
+ val = entry->rw_cntr(entry, context, vl, CNTR_MODE_W,
+ data);
+ }
+ } else {
+ val = entry->rw_cntr(entry, context, vl, CNTR_MODE_W, data);
+ }
+
+ *psval = val;
+
+ hfi1_cdbg(CNTR, "\tNew val=0x%llx", val);
+
+ return val;
+}
+
+u64 read_dev_cntr(struct hfi1_devdata *dd, int index, int vl)
+{
+ struct cntr_entry *entry;
+ u64 *sval;
+
+ entry = &dev_cntrs[index];
+ sval = dd->scntrs + entry->offset;
+
+ if (vl != CNTR_INVALID_VL)
+ sval += vl;
+
+ return read_dev_port_cntr(dd, entry, sval, dd, vl);
+}
+
+u64 write_dev_cntr(struct hfi1_devdata *dd, int index, int vl, u64 data)
+{
+ struct cntr_entry *entry;
+ u64 *sval;
+
+ entry = &dev_cntrs[index];
+ sval = dd->scntrs + entry->offset;
+
+ if (vl != CNTR_INVALID_VL)
+ sval += vl;
+
+ return write_dev_port_cntr(dd, entry, sval, dd, vl, data);
+}
+
+u64 read_port_cntr(struct hfi1_pportdata *ppd, int index, int vl)
+{
+ struct cntr_entry *entry;
+ u64 *sval;
+
+ entry = &port_cntrs[index];
+ sval = ppd->scntrs + entry->offset;
+
+ if (vl != CNTR_INVALID_VL)
+ sval += vl;
+
+ if ((index >= C_RCV_HDR_OVF_FIRST + ppd->dd->num_rcv_contexts) &&
+ (index <= C_RCV_HDR_OVF_LAST)) {
+ /* We do not want to bother for d