| Message ID | 1485773044-31489-4-git-send-email-akdwived@codeaurora.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
On 01/30, Avaneesh Kumar Dwivedi wrote: > diff --git a/drivers/remoteproc/qcom_q6v5_pil.c b/drivers/remoteproc/qcom_q6v5_pil.c > index 35eee68..9c12a36 100644 > --- a/drivers/remoteproc/qcom_q6v5_pil.c > +++ b/drivers/remoteproc/qcom_q6v5_pil.c > @@ -485,35 +497,99 @@ static int q6v5_rmb_mba_wait(struct q6v5 *qproc, u32 status, int ms) > > static int q6v5proc_reset(struct q6v5 *qproc) > { > - u32 val; > + u64 val; Why u64? There isn't any readq/writeq usage here. > int ret; > + int i; > [...] > + if (qproc->version == MSS_MSM8996) { > + /* Override the ACC value if required */ > + writel(QDSP6SS_ACC_OVERRIDE_VAL, > + qproc->reg_base + QDSP6SS_STRAP_ACC); > + > + /* Assert resets, stop core */ > + val = readl(qproc->reg_base + QDSP6SS_RESET_REG); > + val |= (Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE); Useless parenthesis. > + writel(val, qproc->reg_base + QDSP6SS_RESET_REG); > + > + /* BHS require xo cbcr to be enabled */ > + val = readl(qproc->reg_base + QDSP6SS_XO_CBCR); > + val |= 0x1; > + writel(val, qproc->reg_base + QDSP6SS_XO_CBCR); > > + /* Read CLKOFF bit to go low indicating CLK is enabled */ > + ret = readl_poll_timeout(qproc->reg_base + QDSP6SS_XO_CBCR, > + val, !(val & BIT(31)), 1, HALT_CHECK_MAX_LOOPS); > + if (ret) { > + dev_err(qproc->dev, > + "xo cbcr enabling timed out (rc:%d)\n", ret); > + return ret; > + } > + /* Enable power block headswitch and wait for it to stabilize */ > + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); > + val |= QDSP6v56_BHS_ON; > + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); > + val |= readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); > + udelay(1); > + > + /* Put LDO in bypass mode */ > + val |= QDSP6v56_LDO_BYP; > + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); > + > + /* Deassert QDSP6 compiler memory clamp */ > + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); > + val &= ~QDSP6v56_CLAMP_QMC_MEM; > + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); > + > + /* Deassert memory peripheral sleep and L2 memory standby */ > + val |= (Q6SS_L2DATA_STBY_N | Q6SS_SLP_RET_N); Useless parenthesis. > + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); > + > + /* Turn on L1, L2, ETB and JU memories 1 at a time */ > + val = readl(qproc->reg_base + QDSP6SS_MEM_PWR_CTL); > + for (i = 19; i >= 0; i--) { > + val |= BIT(i); > + writel(val, qproc->reg_base + > + QDSP6SS_MEM_PWR_CTL); > + /* > + * Read back value to ensure the write is done then > + * wait for 1us for both memory peripheral and data > + * array to turn on. > + */ > + val |= readl(qproc->reg_base + QDSP6SS_MEM_PWR_CTL); > + udelay(1); > + } > + /* Remove word line clamp */ > + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); > + val &= ~QDSP6v56_CLAMP_WL; > + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); > + } else { > + /* Assert resets, stop core */ > + val = readl(qproc->reg_base + QDSP6SS_RESET_REG); > + val |= (Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE); Useless parenthesis. > + writel(val, qproc->reg_base + QDSP6SS_RESET_REG); > + > + /* Enable power block headswitch and wait for it to stabilize */ > + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); > + val |= QDSS_BHS_ON | QDSS_LDO_BYP; > + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); > + val |= readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); > + udelay(1); > @@ -849,6 +925,7 @@ static int q6v5_stop(struct rproc *rproc) > { > struct q6v5 *qproc = (struct q6v5 *)rproc->priv; > int ret; > + int val; u32 instead of int? > > qproc->running = false; > > @@ -866,6 +943,15 @@ static int q6v5_stop(struct rproc *rproc) > q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_modem); > q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_nc); > > + if (qproc->version == MSS_MSM8996) { > + /* > + * To avoid high MX current during LPASS/MSS restart. > + */ Three lines could be one line comment instead. > + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); > + val |= Q6SS_CLAMP_IO | QDSP6v56_CLAMP_WL | > + QDSP6v56_CLAMP_QMC_MEM; > + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); > + } > reset_control_assert(qproc->mss_restart); > q6v5_clk_disable(qproc->dev, qproc->active_clks, > qproc->active_clk_count); > @@ -1213,6 +1299,47 @@ static int q6v5_remove(struct platform_device *pdev) > return 0; > } > > +static const struct rproc_hexagon_res msm8996_mss = { > + .hexagon_mba_image = "mba.mbn", > + .proxy_supply = (struct qcom_mss_reg_res[]) { > + { > + .supply = "vdd_mx", > + .uV = 6, > + }, > + { > + .supply = "vdd_cx", > + .uV = 7, > + .uA = 100000, > + }, vdd cx and vdd mx are corners. The plan is to _not_ use the regulator framework for those, so treating them like supplies is incorrect here. > + { > + .supply = "vdd_pll", > + .uV = 1800000, > + .uA = 100000, > + }, > + {} > + },
On 2/28/2017 4:18 AM, Stephen Boyd wrote: > On 01/30, Avaneesh Kumar Dwivedi wrote: >> diff --git a/drivers/remoteproc/qcom_q6v5_pil.c b/drivers/remoteproc/qcom_q6v5_pil.c >> index 35eee68..9c12a36 100644 >> --- a/drivers/remoteproc/qcom_q6v5_pil.c >> +++ b/drivers/remoteproc/qcom_q6v5_pil.c >> @@ -485,35 +497,99 @@ static int q6v5_rmb_mba_wait(struct q6v5 *qproc, u32 status, int ms) >> >> static int q6v5proc_reset(struct q6v5 *qproc) >> { >> - u32 val; >> + u64 val; > Why u64? There isn't any readq/writeq usage here. OK > >> int ret; >> + int i; >> > [...] >> + if (qproc->version == MSS_MSM8996) { >> + /* Override the ACC value if required */ >> + writel(QDSP6SS_ACC_OVERRIDE_VAL, >> + qproc->reg_base + QDSP6SS_STRAP_ACC); >> + >> + /* Assert resets, stop core */ >> + val = readl(qproc->reg_base + QDSP6SS_RESET_REG); >> + val |= (Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE); > Useless parenthesis. ok > >> + writel(val, qproc->reg_base + QDSP6SS_RESET_REG); >> + >> + /* BHS require xo cbcr to be enabled */ >> + val = readl(qproc->reg_base + QDSP6SS_XO_CBCR); >> + val |= 0x1; >> + writel(val, qproc->reg_base + QDSP6SS_XO_CBCR); >> >> + /* Read CLKOFF bit to go low indicating CLK is enabled */ >> + ret = readl_poll_timeout(qproc->reg_base + QDSP6SS_XO_CBCR, >> + val, !(val & BIT(31)), 1, HALT_CHECK_MAX_LOOPS); >> + if (ret) { >> + dev_err(qproc->dev, >> + "xo cbcr enabling timed out (rc:%d)\n", ret); >> + return ret; >> + } >> + /* Enable power block headswitch and wait for it to stabilize */ >> + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); >> + val |= QDSP6v56_BHS_ON; >> + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); >> + val |= readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); >> + udelay(1); >> + >> + /* Put LDO in bypass mode */ >> + val |= QDSP6v56_LDO_BYP; >> + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); >> + >> + /* Deassert QDSP6 compiler memory clamp */ >> + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); >> + val &= ~QDSP6v56_CLAMP_QMC_MEM; >> + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); >> + >> + /* Deassert memory peripheral sleep and L2 memory standby */ >> + val |= (Q6SS_L2DATA_STBY_N | Q6SS_SLP_RET_N); > Useless parenthesis. ok > >> + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); >> + >> + /* Turn on L1, L2, ETB and JU memories 1 at a time */ >> + val = readl(qproc->reg_base + QDSP6SS_MEM_PWR_CTL); >> + for (i = 19; i >= 0; i--) { >> + val |= BIT(i); >> + writel(val, qproc->reg_base + >> + QDSP6SS_MEM_PWR_CTL); >> + /* >> + * Read back value to ensure the write is done then >> + * wait for 1us for both memory peripheral and data >> + * array to turn on. >> + */ >> + val |= readl(qproc->reg_base + QDSP6SS_MEM_PWR_CTL); >> + udelay(1); >> + } >> + /* Remove word line clamp */ >> + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); >> + val &= ~QDSP6v56_CLAMP_WL; >> + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); >> + } else { >> + /* Assert resets, stop core */ >> + val = readl(qproc->reg_base + QDSP6SS_RESET_REG); >> + val |= (Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE); > Useless parenthesis. ok > >> + writel(val, qproc->reg_base + QDSP6SS_RESET_REG); >> + >> + /* Enable power block headswitch and wait for it to stabilize */ >> + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); >> + val |= QDSS_BHS_ON | QDSS_LDO_BYP; >> + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); >> + val |= readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); >> + udelay(1); >> @@ -849,6 +925,7 @@ static int q6v5_stop(struct rproc *rproc) >> { >> struct q6v5 *qproc = (struct q6v5 *)rproc->priv; >> int ret; >> + int val; > u32 instead of int? ok > >> >> qproc->running = false; >> >> @@ -866,6 +943,15 @@ static int q6v5_stop(struct rproc *rproc) >> q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_modem); >> q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_nc); >> >> + if (qproc->version == MSS_MSM8996) { >> + /* >> + * To avoid high MX current during LPASS/MSS restart. >> + */ > Three lines could be one line comment instead. ok. > >> + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); >> + val |= Q6SS_CLAMP_IO | QDSP6v56_CLAMP_WL | >> + QDSP6v56_CLAMP_QMC_MEM; >> + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); >> + } >> reset_control_assert(qproc->mss_restart); >> q6v5_clk_disable(qproc->dev, qproc->active_clks, >> qproc->active_clk_count); >> @@ -1213,6 +1299,47 @@ static int q6v5_remove(struct platform_device *pdev) >> return 0; >> } >> >> +static const struct rproc_hexagon_res msm8996_mss = { >> + .hexagon_mba_image = "mba.mbn", >> + .proxy_supply = (struct qcom_mss_reg_res[]) { >> + { >> + .supply = "vdd_mx", >> + .uV = 6, >> + }, >> + { >> + .supply = "vdd_cx", >> + .uV = 7, >> + .uA = 100000, >> + }, > vdd cx and vdd mx are corners. The plan is to _not_ use the > regulator framework for those, so treating them like supplies is > incorrect here. vdd cx and mx though in downstream are voted for corner but they are always ON domain upstream as per regulator team when i discussed with them. should i drop them altogether? > >> + { >> + .supply = "vdd_pll", >> + .uV = 1800000, >> + .uA = 100000, >> + }, >> + {} >> + },
On 03/03, Dwivedi, Avaneesh Kumar (avani) wrote: > On 2/28/2017 4:18 AM, Stephen Boyd wrote: > >On 01/30, Avaneesh Kumar Dwivedi wrote: > >>@@ -1213,6 +1299,47 @@ static int q6v5_remove(struct platform_device *pdev) > >> return 0; > >> } > >>+static const struct rproc_hexagon_res msm8996_mss = { > >>+ .hexagon_mba_image = "mba.mbn", > >>+ .proxy_supply = (struct qcom_mss_reg_res[]) { > >>+ { > >>+ .supply = "vdd_mx", > >>+ .uV = 6, > >>+ }, > >>+ { > >>+ .supply = "vdd_cx", > >>+ .uV = 7, > >>+ .uA = 100000, > >>+ }, > >vdd cx and vdd mx are corners. The plan is to _not_ use the > >regulator framework for those, so treating them like supplies is > >incorrect here. > vdd cx and mx though in downstream are voted for corner but they are > always ON domain upstream as per regulator team when i discussed > with them. > should i drop them altogether? I would say yes, drop them. The on/off state doesn't matter here. This code wants to max out the corner for a period of time until the remote processor has booted far enough to make their own vote on these RPM resources.
diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt index 674ebc6..06f51a6 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt @@ -10,6 +10,7 @@ on the Qualcomm Hexagon core. "qcom,q6v5-pil" "qcom,msm8916-mss-pil" "qcom,msm8974-mss-pil" + "qcom,msm8996-mss-pil" - reg: Usage: required diff --git a/drivers/remoteproc/qcom_q6v5_pil.c b/drivers/remoteproc/qcom_q6v5_pil.c index 35eee68..9c12a36 100644 --- a/drivers/remoteproc/qcom_q6v5_pil.c +++ b/drivers/remoteproc/qcom_q6v5_pil.c @@ -31,6 +31,7 @@ #include <linux/soc/qcom/smem.h> #include <linux/soc/qcom/smem_state.h> #include <linux/of_device.h> +#include <linux/iopoll.h> #include "remoteproc_internal.h" #include "qcom_mdt_loader.h" @@ -65,6 +66,8 @@ #define QDSP6SS_RESET_REG 0x014 #define QDSP6SS_GFMUX_CTL_REG 0x020 #define QDSP6SS_PWR_CTL_REG 0x030 +#define QDSP6SS_MEM_PWR_CTL 0x0B0 +#define QDSP6SS_STRAP_ACC 0x110 /* AXI Halt Register Offsets */ #define AXI_HALTREQ_REG 0x0 @@ -93,6 +96,15 @@ #define QDSS_BHS_ON BIT(21) #define QDSS_LDO_BYP BIT(22) +/* QDSP6v56 parameters */ +#define QDSP6v56_LDO_BYP BIT(25) +#define QDSP6v56_BHS_ON BIT(24) +#define QDSP6v56_CLAMP_WL BIT(21) +#define QDSP6v56_CLAMP_QMC_MEM BIT(22) +#define HALT_CHECK_MAX_LOOPS 200 +#define QDSP6SS_XO_CBCR 0x0038 +#define QDSP6SS_ACC_OVERRIDE_VAL 0x20 + struct dest_vm_and_perm_info { __le32 vm; __le32 perm; @@ -485,35 +497,99 @@ static int q6v5_rmb_mba_wait(struct q6v5 *qproc, u32 status, int ms) static int q6v5proc_reset(struct q6v5 *qproc) { - u32 val; + u64 val; int ret; + int i; - /* Assert resets, stop core */ - val = readl(qproc->reg_base + QDSP6SS_RESET_REG); - val |= (Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE); - writel(val, qproc->reg_base + QDSP6SS_RESET_REG); - /* Enable power block headswitch, and wait for it to stabilize */ - val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); - val |= QDSS_BHS_ON | QDSS_LDO_BYP; - writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); - udelay(1); - - /* - * Turn on memories. L2 banks should be done individually - * to minimize inrush current. - */ - val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); - val |= Q6SS_SLP_RET_N | Q6SS_L2TAG_SLP_NRET_N | - Q6SS_ETB_SLP_NRET_N | Q6SS_L2DATA_STBY_N; - writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); - val |= Q6SS_L2DATA_SLP_NRET_N_2; - writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); - val |= Q6SS_L2DATA_SLP_NRET_N_1; - writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); - val |= Q6SS_L2DATA_SLP_NRET_N_0; - writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + if (qproc->version == MSS_MSM8996) { + /* Override the ACC value if required */ + writel(QDSP6SS_ACC_OVERRIDE_VAL, + qproc->reg_base + QDSP6SS_STRAP_ACC); + + /* Assert resets, stop core */ + val = readl(qproc->reg_base + QDSP6SS_RESET_REG); + val |= (Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE); + writel(val, qproc->reg_base + QDSP6SS_RESET_REG); + + /* BHS require xo cbcr to be enabled */ + val = readl(qproc->reg_base + QDSP6SS_XO_CBCR); + val |= 0x1; + writel(val, qproc->reg_base + QDSP6SS_XO_CBCR); + /* Read CLKOFF bit to go low indicating CLK is enabled */ + ret = readl_poll_timeout(qproc->reg_base + QDSP6SS_XO_CBCR, + val, !(val & BIT(31)), 1, HALT_CHECK_MAX_LOOPS); + if (ret) { + dev_err(qproc->dev, + "xo cbcr enabling timed out (rc:%d)\n", ret); + return ret; + } + /* Enable power block headswitch and wait for it to stabilize */ + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val |= QDSP6v56_BHS_ON; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val |= readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); + udelay(1); + + /* Put LDO in bypass mode */ + val |= QDSP6v56_LDO_BYP; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + + /* Deassert QDSP6 compiler memory clamp */ + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val &= ~QDSP6v56_CLAMP_QMC_MEM; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + + /* Deassert memory peripheral sleep and L2 memory standby */ + val |= (Q6SS_L2DATA_STBY_N | Q6SS_SLP_RET_N); + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + + /* Turn on L1, L2, ETB and JU memories 1 at a time */ + val = readl(qproc->reg_base + QDSP6SS_MEM_PWR_CTL); + for (i = 19; i >= 0; i--) { + val |= BIT(i); + writel(val, qproc->reg_base + + QDSP6SS_MEM_PWR_CTL); + /* + * Read back value to ensure the write is done then + * wait for 1us for both memory peripheral and data + * array to turn on. + */ + val |= readl(qproc->reg_base + QDSP6SS_MEM_PWR_CTL); + udelay(1); + } + /* Remove word line clamp */ + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val &= ~QDSP6v56_CLAMP_WL; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + } else { + /* Assert resets, stop core */ + val = readl(qproc->reg_base + QDSP6SS_RESET_REG); + val |= (Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE); + writel(val, qproc->reg_base + QDSP6SS_RESET_REG); + + /* Enable power block headswitch and wait for it to stabilize */ + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val |= QDSS_BHS_ON | QDSS_LDO_BYP; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val |= readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); + udelay(1); + /* + * Turn on memories. L2 banks should be done individually + * to minimize inrush current. + */ + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val |= Q6SS_SLP_RET_N | Q6SS_L2TAG_SLP_NRET_N | + Q6SS_ETB_SLP_NRET_N | Q6SS_L2DATA_STBY_N; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val |= Q6SS_L2DATA_SLP_NRET_N_2; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val |= Q6SS_L2DATA_SLP_NRET_N_1; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val |= Q6SS_L2DATA_SLP_NRET_N_0; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + } /* Remove IO clamp */ val &= ~Q6SS_CLAMP_IO; writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); @@ -849,6 +925,7 @@ static int q6v5_stop(struct rproc *rproc) { struct q6v5 *qproc = (struct q6v5 *)rproc->priv; int ret; + int val; qproc->running = false; @@ -866,6 +943,15 @@ static int q6v5_stop(struct rproc *rproc) q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_modem); q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_nc); + if (qproc->version == MSS_MSM8996) { + /* + * To avoid high MX current during LPASS/MSS restart. + */ + val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); + val |= Q6SS_CLAMP_IO | QDSP6v56_CLAMP_WL | + QDSP6v56_CLAMP_QMC_MEM; + writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); + } reset_control_assert(qproc->mss_restart); q6v5_clk_disable(qproc->dev, qproc->active_clks, qproc->active_clk_count); @@ -1213,6 +1299,47 @@ static int q6v5_remove(struct platform_device *pdev) return 0; } +static const struct rproc_hexagon_res msm8996_mss = { + .hexagon_mba_image = "mba.mbn", + .proxy_supply = (struct qcom_mss_reg_res[]) { + { + .supply = "vdd_mx", + .uV = 6, + }, + { + .supply = "vdd_cx", + .uV = 7, + .uA = 100000, + }, + { + .supply = "vdd_pll", + .uV = 1800000, + .uA = 100000, + }, + {} + }, + .active_supply = (struct qcom_mss_reg_res[]) { + {}, + {} + }, + .proxy_clk_names = (char*[]){ + "xo", + "pnoc", + "qdss", + NULL + }, + .active_clk_names = (char*[]){ + "iface", + "bus", + "mem", + "gpll0_mss_clk", + "snoc_axi_clk", + "mnoc_axi_clk", + NULL + }, + .version = MSS_MSM8996, +}; + static const struct rproc_hexagon_res msm8916_mss = { .hexagon_mba_image = "mba.mbn", .proxy_supply = (struct qcom_mss_reg_res[]) { @@ -1292,6 +1419,7 @@ static int q6v5_remove(struct platform_device *pdev) { .compatible = "qcom,q6v5-pil", .data = &msm8916_mss}, { .compatible = "qcom,msm8916-mss-pil", .data = &msm8916_mss}, { .compatible = "qcom,msm8974-mss-pil", .data = &msm8974_mss}, + { .compatible = "qcom,msm8996-mss-pil", .data = &msm8996_mss}, { }, }; MODULE_DEVICE_TABLE(of, q6v5_of_match);
This patch add msm8996 support in existing mss rproc driver. Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org> --- .../devicetree/bindings/remoteproc/qcom,q6v5.txt | 1 + drivers/remoteproc/qcom_q6v5_pil.c | 178 ++++++++++++++++++--- 2 files changed, 154 insertions(+), 25 deletions(-)