diff mbox series

[v3,3/8] media: i2c: ov6650: Use new [g|s]_mbus_config op

Message ID 20200514164540.507233-5-jacopo+renesas@jmondi.org (mailing list archive)
State Superseded
Delegated to: Kieran Bingham
Headers show
Series v4l2-subdev: Introduce [g|s]et_mbus_format pad op | expand

Commit Message

Jacopo Mondi May 14, 2020, 4:45 p.m. UTC
Use the new get_mbus_config and set_mbus_config pad operation in place
of the video operations currently in use.

Compared to other drivers where the same conversion has been performed,
ov6650 proves to be a bit more tricky, as the existing g_mbus_config
implementation did not report the currently applied configuration but
the set of all possible configuration options.

Adapt the driver to support the semantic of the two newly introduced
operations:
- get_mbus_config reports the current media bus configuration
- set_mbus_config applies only changes explicitly requested and updates
  the provided cfg parameter to report what has actually been applied to
  the hardware.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
 drivers/media/i2c/ov6650.c | 56 ++++++++++++++++++++++++++------------
 1 file changed, 39 insertions(+), 17 deletions(-)

Comments

Kieran Bingham May 18, 2020, 10 a.m. UTC | #1
Hi Jacopo,

The $SUBJECT here references {g,s}_mbus instead of {get,set}_mbus... and
might also need updating.
--
Kieran

On 14/05/2020 17:45, Jacopo Mondi wrote:
> Use the new get_mbus_config and set_mbus_config pad operation in place
> of the video operations currently in use.
> 
> Compared to other drivers where the same conversion has been performed,
> ov6650 proves to be a bit more tricky, as the existing g_mbus_config
> implementation did not report the currently applied configuration but
> the set of all possible configuration options.
> 
> Adapt the driver to support the semantic of the two newly introduced
> operations:
> - get_mbus_config reports the current media bus configuration
> - set_mbus_config applies only changes explicitly requested and updates
>   the provided cfg parameter to report what has actually been applied to
>   the hardware.
> 
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> ---
>  drivers/media/i2c/ov6650.c | 56 ++++++++++++++++++++++++++------------
>  1 file changed, 39 insertions(+), 17 deletions(-)
> 
> diff --git a/drivers/media/i2c/ov6650.c b/drivers/media/i2c/ov6650.c
> index 91906b94f978..efc798bac3a4 100644
> --- a/drivers/media/i2c/ov6650.c
> +++ b/drivers/media/i2c/ov6650.c
> @@ -921,46 +921,68 @@ static const struct v4l2_subdev_core_ops ov6650_core_ops = {
>  };
>  
>  /* Request bus settings on camera side */
> -static int ov6650_g_mbus_config(struct v4l2_subdev *sd,
> -				struct v4l2_mbus_config *cfg)
> +static int ov6650_get_mbus_config(struct v4l2_subdev *sd,
> +				  unsigned int pad,
> +				  struct v4l2_mbus_config *cfg)
>  {
> +	struct i2c_client *client = v4l2_get_subdevdata(sd);
> +	u8 comj, comf;
> +	int ret;
> +
> +	ret = ov6650_reg_read(client, REG_COMJ, &comj);
> +	if (ret)
> +		return ret;
>  
> -	cfg->flags = V4L2_MBUS_MASTER |
> -		V4L2_MBUS_PCLK_SAMPLE_RISING | V4L2_MBUS_PCLK_SAMPLE_FALLING |
> -		V4L2_MBUS_HSYNC_ACTIVE_HIGH | V4L2_MBUS_HSYNC_ACTIVE_LOW |
> -		V4L2_MBUS_VSYNC_ACTIVE_HIGH | V4L2_MBUS_VSYNC_ACTIVE_LOW |
> -		V4L2_MBUS_DATA_ACTIVE_HIGH;
> +	ret = ov6650_reg_read(client, REG_COMF, &comf);
> +	if (ret)
> +		return ret;
> +
> +	cfg->flags = V4L2_MBUS_MASTER
> +		   |  (comj & COMJ_VSYNC_HIGH  ? V4L2_MBUS_VSYNC_ACTIVE_HIGH
> +					       : V4L2_MBUS_VSYNC_ACTIVE_LOW)
> +		   |  (comf & COMF_HREF_LOW    ? V4L2_MBUS_HSYNC_ACTIVE_LOW
> +					       : V4L2_MBUS_HSYNC_ACTIVE_HIGH)
> +		   |  (comj & COMJ_PCLK_RISING ? V4L2_MBUS_PCLK_SAMPLE_RISING
> +					       : V4L2_MBUS_PCLK_SAMPLE_FALLING);
>  	cfg->type = V4L2_MBUS_PARALLEL;
>  
>  	return 0;
>  }
>  
>  /* Alter bus settings on camera side */
> -static int ov6650_s_mbus_config(struct v4l2_subdev *sd,
> -				const struct v4l2_mbus_config *cfg)
> +static int ov6650_set_mbus_config(struct v4l2_subdev *sd,
> +				  unsigned int pad,
> +				  struct v4l2_mbus_config *cfg)
>  {
>  	struct i2c_client *client = v4l2_get_subdevdata(sd);
> -	int ret;
> +	int ret = 0;
>  
>  	if (cfg->flags & V4L2_MBUS_PCLK_SAMPLE_RISING)
>  		ret = ov6650_reg_rmw(client, REG_COMJ, COMJ_PCLK_RISING, 0);
> -	else
> +	else if (cfg->flags & V4L2_MBUS_PCLK_SAMPLE_FALLING)
>  		ret = ov6650_reg_rmw(client, REG_COMJ, 0, COMJ_PCLK_RISING);
>  	if (ret)
> -		return ret;
> +		goto error;
>  
>  	if (cfg->flags & V4L2_MBUS_HSYNC_ACTIVE_LOW)
>  		ret = ov6650_reg_rmw(client, REG_COMF, COMF_HREF_LOW, 0);
> -	else
> +	else if (cfg->flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH)
>  		ret = ov6650_reg_rmw(client, REG_COMF, 0, COMF_HREF_LOW);
>  	if (ret)
> -		return ret;
> +		goto error;
>  
>  	if (cfg->flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH)
>  		ret = ov6650_reg_rmw(client, REG_COMJ, COMJ_VSYNC_HIGH, 0);
> -	else
> +	else if (cfg->flags & V4L2_MBUS_VSYNC_ACTIVE_LOW)
>  		ret = ov6650_reg_rmw(client, REG_COMJ, 0, COMJ_VSYNC_HIGH);
>  
> +error:
> +	/*
> +	 * Update the configuration to report what is actually applied to
> +	 * the hardware.
> +	 */
> +	ov6650_get_mbus_config(sd, pad, cfg);
> +
>  	return ret;
>  }
>  
> @@ -968,8 +990,6 @@ static const struct v4l2_subdev_video_ops ov6650_video_ops = {
>  	.s_stream	= ov6650_s_stream,
>  	.g_frame_interval = ov6650_g_frame_interval,
>  	.s_frame_interval = ov6650_s_frame_interval,
> -	.g_mbus_config	= ov6650_g_mbus_config,
> -	.s_mbus_config	= ov6650_s_mbus_config,
>  };
>  
>  static const struct v4l2_subdev_pad_ops ov6650_pad_ops = {
> @@ -978,6 +998,8 @@ static const struct v4l2_subdev_pad_ops ov6650_pad_ops = {
>  	.set_selection	= ov6650_set_selection,
>  	.get_fmt	= ov6650_get_fmt,
>  	.set_fmt	= ov6650_set_fmt,
> +	.get_mbus_config = ov6650_get_mbus_config,
> +	.set_mbus_config = ov6650_set_mbus_config,
>  };
>  
>  static const struct v4l2_subdev_ops ov6650_subdev_ops = {
>
diff mbox series

Patch

diff --git a/drivers/media/i2c/ov6650.c b/drivers/media/i2c/ov6650.c
index 91906b94f978..efc798bac3a4 100644
--- a/drivers/media/i2c/ov6650.c
+++ b/drivers/media/i2c/ov6650.c
@@ -921,46 +921,68 @@  static const struct v4l2_subdev_core_ops ov6650_core_ops = {
 };
 
 /* Request bus settings on camera side */
-static int ov6650_g_mbus_config(struct v4l2_subdev *sd,
-				struct v4l2_mbus_config *cfg)
+static int ov6650_get_mbus_config(struct v4l2_subdev *sd,
+				  unsigned int pad,
+				  struct v4l2_mbus_config *cfg)
 {
+	struct i2c_client *client = v4l2_get_subdevdata(sd);
+	u8 comj, comf;
+	int ret;
+
+	ret = ov6650_reg_read(client, REG_COMJ, &comj);
+	if (ret)
+		return ret;
 
-	cfg->flags = V4L2_MBUS_MASTER |
-		V4L2_MBUS_PCLK_SAMPLE_RISING | V4L2_MBUS_PCLK_SAMPLE_FALLING |
-		V4L2_MBUS_HSYNC_ACTIVE_HIGH | V4L2_MBUS_HSYNC_ACTIVE_LOW |
-		V4L2_MBUS_VSYNC_ACTIVE_HIGH | V4L2_MBUS_VSYNC_ACTIVE_LOW |
-		V4L2_MBUS_DATA_ACTIVE_HIGH;
+	ret = ov6650_reg_read(client, REG_COMF, &comf);
+	if (ret)
+		return ret;
+
+	cfg->flags = V4L2_MBUS_MASTER
+		   |  (comj & COMJ_VSYNC_HIGH  ? V4L2_MBUS_VSYNC_ACTIVE_HIGH
+					       : V4L2_MBUS_VSYNC_ACTIVE_LOW)
+		   |  (comf & COMF_HREF_LOW    ? V4L2_MBUS_HSYNC_ACTIVE_LOW
+					       : V4L2_MBUS_HSYNC_ACTIVE_HIGH)
+		   |  (comj & COMJ_PCLK_RISING ? V4L2_MBUS_PCLK_SAMPLE_RISING
+					       : V4L2_MBUS_PCLK_SAMPLE_FALLING);
 	cfg->type = V4L2_MBUS_PARALLEL;
 
 	return 0;
 }
 
 /* Alter bus settings on camera side */
-static int ov6650_s_mbus_config(struct v4l2_subdev *sd,
-				const struct v4l2_mbus_config *cfg)
+static int ov6650_set_mbus_config(struct v4l2_subdev *sd,
+				  unsigned int pad,
+				  struct v4l2_mbus_config *cfg)
 {
 	struct i2c_client *client = v4l2_get_subdevdata(sd);
-	int ret;
+	int ret = 0;
 
 	if (cfg->flags & V4L2_MBUS_PCLK_SAMPLE_RISING)
 		ret = ov6650_reg_rmw(client, REG_COMJ, COMJ_PCLK_RISING, 0);
-	else
+	else if (cfg->flags & V4L2_MBUS_PCLK_SAMPLE_FALLING)
 		ret = ov6650_reg_rmw(client, REG_COMJ, 0, COMJ_PCLK_RISING);
 	if (ret)
-		return ret;
+		goto error;
 
 	if (cfg->flags & V4L2_MBUS_HSYNC_ACTIVE_LOW)
 		ret = ov6650_reg_rmw(client, REG_COMF, COMF_HREF_LOW, 0);
-	else
+	else if (cfg->flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH)
 		ret = ov6650_reg_rmw(client, REG_COMF, 0, COMF_HREF_LOW);
 	if (ret)
-		return ret;
+		goto error;
 
 	if (cfg->flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH)
 		ret = ov6650_reg_rmw(client, REG_COMJ, COMJ_VSYNC_HIGH, 0);
-	else
+	else if (cfg->flags & V4L2_MBUS_VSYNC_ACTIVE_LOW)
 		ret = ov6650_reg_rmw(client, REG_COMJ, 0, COMJ_VSYNC_HIGH);
 
+error:
+	/*
+	 * Update the configuration to report what is actually applied to
+	 * the hardware.
+	 */
+	ov6650_get_mbus_config(sd, pad, cfg);
+
 	return ret;
 }
 
@@ -968,8 +990,6 @@  static const struct v4l2_subdev_video_ops ov6650_video_ops = {
 	.s_stream	= ov6650_s_stream,
 	.g_frame_interval = ov6650_g_frame_interval,
 	.s_frame_interval = ov6650_s_frame_interval,
-	.g_mbus_config	= ov6650_g_mbus_config,
-	.s_mbus_config	= ov6650_s_mbus_config,
 };
 
 static const struct v4l2_subdev_pad_ops ov6650_pad_ops = {
@@ -978,6 +998,8 @@  static const struct v4l2_subdev_pad_ops ov6650_pad_ops = {
 	.set_selection	= ov6650_set_selection,
 	.get_fmt	= ov6650_get_fmt,
 	.set_fmt	= ov6650_set_fmt,
+	.get_mbus_config = ov6650_get_mbus_config,
+	.set_mbus_config = ov6650_set_mbus_config,
 };
 
 static const struct v4l2_subdev_ops ov6650_subdev_ops = {