diff mbox series

[05/13] dt-bindings: media: ov5640: Make bus-type mandatory

Message ID 20200717132859.237120-6-jacopo+renesas@jmondi.org (mailing list archive)
State New
Delegated to: Kieran Bingham
Headers show
Series dt-bindings: media: ov5640: Convert to json-schema | expand

Commit Message

Jacopo Mondi July 17, 2020, 1:28 p.m. UTC
The ov5640 driver supports both a parallel data interface and a
CSI-2 serial data interface.

Depending on which interface is in use, the required endpoint
properties are different. In order to be able to validate if a
device node is compliant with the dt-schema bindings, start by
making the bus-type a mandatory property, and add it to all the
existing users of ov5640 in mainline DTS.

On top of this, endpoint properties validation will be implemented,
conditionally to the reported bus type.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
 Documentation/devicetree/bindings/media/i2c/ov5640.yaml    | 6 ++++++
 arch/arm/boot/dts/dra72-evm-common.dtsi                    | 1 +
 arch/arm/boot/dts/dra76-evm.dts                            | 1 +
 arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi              | 1 +
 arch/arm/boot/dts/imx6qdl-icore.dtsi                       | 1 +
 arch/arm/boot/dts/imx6qdl-sabrelite.dtsi                   | 1 +
 arch/arm/boot/dts/imx6qdl-sabresd.dtsi                     | 1 +
 arch/arm/boot/dts/stm32mp157c-ev1.dts                      | 1 +
 arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts | 1 +
 arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts       | 1 +
 arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi                  | 1 +
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts             | 1 +
 12 files changed, 17 insertions(+)

--
2.27.0

Comments

Fabio Estevam July 17, 2020, 3:48 p.m. UTC | #1
Hi Jacopo,

On Fri, Jul 17, 2020 at 10:25 AM Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:

> diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.yaml b/Documentation/devicetree/bindings/media/i2c/ov5640.yaml
> index 503f8b78615c..16e6c2dc629a 100644
> --- a/Documentation/devicetree/bindings/media/i2c/ov5640.yaml
> +++ b/Documentation/devicetree/bindings/media/i2c/ov5640.yaml
> @@ -73,6 +73,9 @@ properties:
>            remote-endpoint:
>              description: A phandle to the bus receiver's endpoint node.
>
> +          bus-type:
> +            enum: [4, 5]

Can we have an explanation for what the values 4 and 5 mean in the yaml doc?

Looking at the series I see that 4 means MIPI-CSI2 and 5 means
parallel interface, but this is not too obvious (at least for me).

Or maybe we could use a string definition instead of hard coding 4 and 5?
Laurent Pinchart July 17, 2020, 7:48 p.m. UTC | #2
Hi Jacopo,

Thank you for the patch.

On Fri, Jul 17, 2020 at 03:28:51PM +0200, Jacopo Mondi wrote:
> The ov5640 driver supports both a parallel data interface and a
> CSI-2 serial data interface.
> 
> Depending on which interface is in use, the required endpoint
> properties are different. In order to be able to validate if a
> device node is compliant with the dt-schema bindings, start by
> making the bus-type a mandatory property, and add it to all the
> existing users of ov5640 in mainline DTS.
> 
> On top of this, endpoint properties validation will be implemented,
> conditionally to the reported bus type.
> 
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>

Rob may request this to be split in two, one patch for the binding, one
part for the DT sources. I think it's fine to have a temporary
validation breakage between the two patches, but if you want to avoid
that, it would also be possible to first add the property to the text
bindings, update the DT sources, and then convert to YAML. Up to you.

> ---
>  Documentation/devicetree/bindings/media/i2c/ov5640.yaml    | 6 ++++++
>  arch/arm/boot/dts/dra72-evm-common.dtsi                    | 1 +
>  arch/arm/boot/dts/dra76-evm.dts                            | 1 +
>  arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi              | 1 +
>  arch/arm/boot/dts/imx6qdl-icore.dtsi                       | 1 +
>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi                   | 1 +
>  arch/arm/boot/dts/imx6qdl-sabresd.dtsi                     | 1 +
>  arch/arm/boot/dts/stm32mp157c-ev1.dts                      | 1 +
>  arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts | 1 +
>  arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts       | 1 +
>  arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi                  | 1 +
>  arch/arm64/boot/dts/ti/k3-am654-base-board.dts             | 1 +
>  12 files changed, 17 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.yaml b/Documentation/devicetree/bindings/media/i2c/ov5640.yaml
> index 503f8b78615c..16e6c2dc629a 100644
> --- a/Documentation/devicetree/bindings/media/i2c/ov5640.yaml
> +++ b/Documentation/devicetree/bindings/media/i2c/ov5640.yaml
> @@ -73,6 +73,9 @@ properties:
>            remote-endpoint:
>              description: A phandle to the bus receiver's endpoint node.
> 
> +          bus-type:

You may want to add a comment referring to video-interfaces.txt. We
should really have a header file defining macros for the different bus
types. I wonder how that would work with YAML schemas though.

> +            enum: [4, 5]
> +
>            clock-lanes:
>              const: 0
> 
> @@ -109,6 +112,7 @@ properties:
> 
>          required:
>            - remote-endpoint
> +          - bus-type
> 
>      additionalProperties: false
> 

allOf:
  - if:
      properties:
        bus-type:
          const: 4
      then:
        ...
  - if:
      properties:
        bus-type:
          const: 5
      then:
        ...

It's really time to convert video-interfaces.txt... As that's a big
task, how about doing so piece by piece, moving the bus-type rules
first, and leaving the ports and endpoints (and other pieces) for later
? I think nobody wants to touch video-interfaces.txt because it's lots
of work, starting with a smaller piece may help setting the train in
motion.

I'm also fine doing this on top of this series, yak shaving is not
required.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> @@ -146,6 +150,7 @@ examples:
>              port {
>                  ov5640_to_mipi_csi2: endpoint {
>                      remote-endpoint = <&mipi_csi2_from_ov5640>;
> +                    bus-type = <4>;
>                      clock-lanes = <0>;
>                      data-lanes = <1 2>;
>                  };
> @@ -172,6 +177,7 @@ examples:
>              port {
>                  ov5640_to_parallel: endpoint {
>                      remote-endpoint = <&parallel_from_ov5640>;
> +                    bus-type = <5>;
>                      bus-width = <10>;
>                  };
>              };
> diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi
> index c84b63bf0fc8..aba7eb55525d 100644
> --- a/arch/arm/boot/dts/dra72-evm-common.dtsi
> +++ b/arch/arm/boot/dts/dra72-evm-common.dtsi
> @@ -287,6 +287,7 @@ ov5640@3c {
>  		port {
>  			csi2_cam0: endpoint {
>  				remote-endpoint = <&csi2_phy0>;
> +				bus-type = <4>;
>  				clock-lanes = <0>;
>  				data-lanes = <1 2>;
>  			};
> diff --git a/arch/arm/boot/dts/dra76-evm.dts b/arch/arm/boot/dts/dra76-evm.dts
> index 820a0ece20d4..ddf16e65ec7f 100644
> --- a/arch/arm/boot/dts/dra76-evm.dts
> +++ b/arch/arm/boot/dts/dra76-evm.dts
> @@ -420,6 +420,7 @@ ov5640@3c {
>  		port {
>  			csi2_cam0: endpoint {
>  				remote-endpoint = <&csi2_phy0>;
> +				bus-type = <4>;
>  				clock-lanes = <0>;
>  				data-lanes = <1 2>;
>  			};
> diff --git a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi b/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
> index 9e027b9a5f91..dd5765778e87 100644
> --- a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
> +++ b/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
> @@ -274,6 +274,7 @@ ov5640: camera@10 {
>  		port {
>  			ov5640_to_mipi_csi2: endpoint {
>  				remote-endpoint = <&mipi_csi2_in>;
> +				bus-type = <4>;
>  				clock-lanes = <0>;
>  				data-lanes = <1 2>;
>  			};
> diff --git a/arch/arm/boot/dts/imx6qdl-icore.dtsi b/arch/arm/boot/dts/imx6qdl-icore.dtsi
> index 756f3a9f1b4f..2b1f275b8cc4 100644
> --- a/arch/arm/boot/dts/imx6qdl-icore.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-icore.dtsi
> @@ -213,6 +213,7 @@ ov5640: camera@3c {
>  		port {
>  			ov5640_to_mipi_csi2: endpoint {
>  				remote-endpoint = <&mipi_csi2_in>;
> +				bus-type = <4>;
>  				clock-lanes = <0>;
>  				data-lanes = <1 2>;
>  			};
> diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> index 8468216dae9b..5752abb48e68 100644
> --- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
> @@ -382,6 +382,7 @@ ov5640: camera@40 {
>  		port {
>  			ov5640_to_mipi_csi2: endpoint {
>  				remote-endpoint = <&mipi_csi2_in>;
> +				bus-type = <4>;
>  				clock-lanes = <0>;
>  				data-lanes = <1 2>;
>  			};
> diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
> index 28b35ccb3757..990f4cc345da 100644
> --- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
> @@ -313,6 +313,7 @@ rev B board is VGEN5 */
>  		port {
>  			ov5640_to_mipi_csi2: endpoint {
>  				remote-endpoint = <&mipi_csi2_in>;
> +				bus-type = <4>;
>  				clock-lanes = <0>;
>  				data-lanes = <1 2>;
>  			};
> diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
> index b19056557ef0..613ede73b65b 100644
> --- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
> +++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
> @@ -190,6 +190,7 @@ ov5640: camera@3c {
>  		port {
>  			ov5640_0: endpoint {
>  				remote-endpoint = <&dcmi_0>;
> +				bus-type = <5>;
>  				bus-width = <8>;
>  				data-shift = <2>; /* lines 9:2 are used */
>  				hsync-active = <0>;
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
> index c7bd73f35ed8..6ef528bb5564 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
> @@ -46,6 +46,7 @@ ov5640: camera@3c {
>  			port {
>  				ov5640_ep: endpoint {
>  					remote-endpoint = <&csi_ep>;
> +					bus-type = <5>;
>  					bus-width = <8>;
>  					hsync-active = <1>; /* Active high */
>  					vsync-active = <0>; /* Active low */
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
> index dc4ab6b434f9..8ebd6547786e 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
> @@ -61,6 +61,7 @@ ov5640: camera@3c {
>  			port {
>  				ov5640_ep: endpoint {
>  					remote-endpoint = <&csi_ep>;
> +					bus-type = <5>;
>  					bus-width = <8>;
>  					hsync-active = <1>; /* Active high */
>  					vsync-active = <0>; /* Active low */
> diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
> index fe6613676e45..5c79ad5e7b5d 100644
> --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
> +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
> @@ -627,6 +627,7 @@ camera_rear@3b {
> 
>  		port {
>  			ov5640_ep: endpoint {
> +				bus-type = <4>;
>  				clock-lanes = <0>;
>  				data-lanes = <1 2>;
>  				remote-endpoint = <&csiphy0_ep>;
> diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> index 2f3d3316a1cf..33f4eceffbe5 100644
> --- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> @@ -254,6 +254,7 @@ ov5640@3c {
>  		port {
>  			csi2_cam0: endpoint {
>  				remote-endpoint = <&csi2_phy0>;
> +				bus-type = <4>;
>  				clock-lanes = <0>;
>  				data-lanes = <1 2>;
>  			};
Rob Herring July 20, 2020, 7:45 p.m. UTC | #3
On Fri, Jul 17, 2020 at 03:28:51PM +0200, Jacopo Mondi wrote:
> The ov5640 driver supports both a parallel data interface and a
> CSI-2 serial data interface.
> 
> Depending on which interface is in use, the required endpoint
> properties are different. In order to be able to validate if a
> device node is compliant with the dt-schema bindings, start by
> making the bus-type a mandatory property, and add it to all the
> existing users of ov5640 in mainline DTS.

You can't really make a property required on an existing binding. That 
breaks compatibility. Are all the users of the below boards okay with 
that?

There should be a default defined if 'bus-type' is not present.

> 
> On top of this, endpoint properties validation will be implemented,
> conditionally to the reported bus type.
> 
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> ---
>  Documentation/devicetree/bindings/media/i2c/ov5640.yaml    | 6 ++++++
>  arch/arm/boot/dts/dra72-evm-common.dtsi                    | 1 +
>  arch/arm/boot/dts/dra76-evm.dts                            | 1 +
>  arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi              | 1 +
>  arch/arm/boot/dts/imx6qdl-icore.dtsi                       | 1 +
>  arch/arm/boot/dts/imx6qdl-sabrelite.dtsi                   | 1 +
>  arch/arm/boot/dts/imx6qdl-sabresd.dtsi                     | 1 +
>  arch/arm/boot/dts/stm32mp157c-ev1.dts                      | 1 +
>  arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts | 1 +
>  arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts       | 1 +
>  arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi                  | 1 +
>  arch/arm64/boot/dts/ti/k3-am654-base-board.dts             | 1 +
>  12 files changed, 17 insertions(+)
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.yaml b/Documentation/devicetree/bindings/media/i2c/ov5640.yaml
index 503f8b78615c..16e6c2dc629a 100644
--- a/Documentation/devicetree/bindings/media/i2c/ov5640.yaml
+++ b/Documentation/devicetree/bindings/media/i2c/ov5640.yaml
@@ -73,6 +73,9 @@  properties:
           remote-endpoint:
             description: A phandle to the bus receiver's endpoint node.

+          bus-type:
+            enum: [4, 5]
+
           clock-lanes:
             const: 0

@@ -109,6 +112,7 @@  properties:

         required:
           - remote-endpoint
+          - bus-type

     additionalProperties: false

@@ -146,6 +150,7 @@  examples:
             port {
                 ov5640_to_mipi_csi2: endpoint {
                     remote-endpoint = <&mipi_csi2_from_ov5640>;
+                    bus-type = <4>;
                     clock-lanes = <0>;
                     data-lanes = <1 2>;
                 };
@@ -172,6 +177,7 @@  examples:
             port {
                 ov5640_to_parallel: endpoint {
                     remote-endpoint = <&parallel_from_ov5640>;
+                    bus-type = <5>;
                     bus-width = <10>;
                 };
             };
diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi
index c84b63bf0fc8..aba7eb55525d 100644
--- a/arch/arm/boot/dts/dra72-evm-common.dtsi
+++ b/arch/arm/boot/dts/dra72-evm-common.dtsi
@@ -287,6 +287,7 @@  ov5640@3c {
 		port {
 			csi2_cam0: endpoint {
 				remote-endpoint = <&csi2_phy0>;
+				bus-type = <4>;
 				clock-lanes = <0>;
 				data-lanes = <1 2>;
 			};
diff --git a/arch/arm/boot/dts/dra76-evm.dts b/arch/arm/boot/dts/dra76-evm.dts
index 820a0ece20d4..ddf16e65ec7f 100644
--- a/arch/arm/boot/dts/dra76-evm.dts
+++ b/arch/arm/boot/dts/dra76-evm.dts
@@ -420,6 +420,7 @@  ov5640@3c {
 		port {
 			csi2_cam0: endpoint {
 				remote-endpoint = <&csi2_phy0>;
+				bus-type = <4>;
 				clock-lanes = <0>;
 				data-lanes = <1 2>;
 			};
diff --git a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi b/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
index 9e027b9a5f91..dd5765778e87 100644
--- a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
+++ b/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
@@ -274,6 +274,7 @@  ov5640: camera@10 {
 		port {
 			ov5640_to_mipi_csi2: endpoint {
 				remote-endpoint = <&mipi_csi2_in>;
+				bus-type = <4>;
 				clock-lanes = <0>;
 				data-lanes = <1 2>;
 			};
diff --git a/arch/arm/boot/dts/imx6qdl-icore.dtsi b/arch/arm/boot/dts/imx6qdl-icore.dtsi
index 756f3a9f1b4f..2b1f275b8cc4 100644
--- a/arch/arm/boot/dts/imx6qdl-icore.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-icore.dtsi
@@ -213,6 +213,7 @@  ov5640: camera@3c {
 		port {
 			ov5640_to_mipi_csi2: endpoint {
 				remote-endpoint = <&mipi_csi2_in>;
+				bus-type = <4>;
 				clock-lanes = <0>;
 				data-lanes = <1 2>;
 			};
diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
index 8468216dae9b..5752abb48e68 100644
--- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
@@ -382,6 +382,7 @@  ov5640: camera@40 {
 		port {
 			ov5640_to_mipi_csi2: endpoint {
 				remote-endpoint = <&mipi_csi2_in>;
+				bus-type = <4>;
 				clock-lanes = <0>;
 				data-lanes = <1 2>;
 			};
diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
index 28b35ccb3757..990f4cc345da 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -313,6 +313,7 @@  rev B board is VGEN5 */
 		port {
 			ov5640_to_mipi_csi2: endpoint {
 				remote-endpoint = <&mipi_csi2_in>;
+				bus-type = <4>;
 				clock-lanes = <0>;
 				data-lanes = <1 2>;
 			};
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index b19056557ef0..613ede73b65b 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -190,6 +190,7 @@  ov5640: camera@3c {
 		port {
 			ov5640_0: endpoint {
 				remote-endpoint = <&dcmi_0>;
+				bus-type = <5>;
 				bus-width = <8>;
 				data-shift = <2>; /* lines 9:2 are used */
 				hsync-active = <0>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
index c7bd73f35ed8..6ef528bb5564 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
@@ -46,6 +46,7 @@  ov5640: camera@3c {
 			port {
 				ov5640_ep: endpoint {
 					remote-endpoint = <&csi_ep>;
+					bus-type = <5>;
 					bus-width = <8>;
 					hsync-active = <1>; /* Active high */
 					vsync-active = <0>; /* Active low */
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
index dc4ab6b434f9..8ebd6547786e 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
@@ -61,6 +61,7 @@  ov5640: camera@3c {
 			port {
 				ov5640_ep: endpoint {
 					remote-endpoint = <&csi_ep>;
+					bus-type = <5>;
 					bus-width = <8>;
 					hsync-active = <1>; /* Active high */
 					vsync-active = <0>; /* Active low */
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
index fe6613676e45..5c79ad5e7b5d 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
@@ -627,6 +627,7 @@  camera_rear@3b {

 		port {
 			ov5640_ep: endpoint {
+				bus-type = <4>;
 				clock-lanes = <0>;
 				data-lanes = <1 2>;
 				remote-endpoint = <&csiphy0_ep>;
diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index 2f3d3316a1cf..33f4eceffbe5 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -254,6 +254,7 @@  ov5640@3c {
 		port {
 			csi2_cam0: endpoint {
 				remote-endpoint = <&csi2_phy0>;
+				bus-type = <4>;
 				clock-lanes = <0>;
 				data-lanes = <1 2>;
 			};