diff mbox series

[v2,15/15] arm64: dts: renesas: rzg3s-smarc: Enable USB support

Message ID 20241126092050.1825607-16-claudiu.beznea.uj@bp.renesas.com (mailing list archive)
State New
Delegated to: Geert Uytterhoeven
Headers show
Series Add initial USB support for the Renesas RZ/G3S SoC | expand

Commit Message

Claudiu Nov. 26, 2024, 9:20 a.m. UTC 
From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>

Enable USB support (host, device, USB PHYs).

Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
---

Changes in v2:
- this was patch 15/16 in v1:
- dropped sysc enablement as it is now done in SoC dtsi file

 arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi | 57 ++++++++++++++++++++
 1 file changed, 57 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi b/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi
index 4509151344c4..84523e771ebf 100644
--- a/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg3s-smarc.dtsi
@@ -64,12 +64,35 @@  vccq_sdhi1: regulator-vccq-sdhi1 {
 	};
 };
 
+&ehci0 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&hsusb {
+	dr_mode = "otg";
+	status = "okay";
+};
+
 &i2c0 {
 	status = "okay";
 
 	clock-frequency = <1000000>;
 };
 
+&ohci0 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
 &pinctrl {
 	key-1-gpio-hog {
 		gpio-hog;
@@ -128,6 +151,27 @@  cd {
 			pinmux = <RZG2L_PORT_PINMUX(0, 2, 1)>; /* SD1_CD */
 		};
 	};
+
+	usb0_pins: usb0 {
+		peri {
+			pinmux = <RZG2L_PORT_PINMUX(5, 0, 1)>, /* VBUS */
+				 <RZG2L_PORT_PINMUX(5, 2, 1)>; /* OVC */
+		};
+
+		otg {
+			pinmux = <RZG2L_PORT_PINMUX(5, 3, 1)>; /* OTG_ID */
+			bias-pull-up;
+		};
+	};
+
+	usb1_pins: usb1 {
+		pinmux = <RZG2L_PORT_PINMUX(5, 4, 5)>, /* OVC */
+			 <RZG2L_PORT_PINMUX(6, 0, 1)>; /* VBUS */
+	};
+};
+
+&phyrst {
+	status = "okay";
 };
 
 &scif0 {
@@ -148,3 +192,16 @@  &sdhi1 {
 	max-frequency = <125000000>;
 	status = "okay";
 };
+
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+	vbus-supply = <&usb0_vbus_otg>;
+	status = "okay";
+};
+
+&usb2_phy1 {
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};