@@ -540,6 +540,17 @@ config PWM_ROCKCHIP
Generic PWM framework driver for the PWM controller found on
Rockchip SoCs.
+config PWM_RZG2L_GPT
+ tristate "Renesas RZ/G2L General PWM Timer support"
+ depends on ARCH_RZG2L || COMPILE_TEST
+ depends on HAS_IOMEM
+ help
+ This driver exposes the General PWM Timer controller found in Renesas
+ RZ/G2L like chips through the PWM API.
+
+ To compile this driver as a module, choose M here: the module
+ will be called pwm-rzg2l-gpt.
+
config PWM_RZ_MTU3
tristate "Renesas RZ/G2L MTU3a PWM Timer support"
depends on RZ_MTU3
@@ -49,6 +49,7 @@ obj-$(CONFIG_PWM_RASPBERRYPI_POE) += pwm-raspberrypi-poe.o
obj-$(CONFIG_PWM_RCAR) += pwm-rcar.o
obj-$(CONFIG_PWM_RENESAS_TPU) += pwm-renesas-tpu.o
obj-$(CONFIG_PWM_ROCKCHIP) += pwm-rockchip.o
+obj-$(CONFIG_PWM_RZG2L_GPT) += pwm-rzg2l-gpt.o
obj-$(CONFIG_PWM_RZ_MTU3) += pwm-rz-mtu3.o
obj-$(CONFIG_PWM_SAMSUNG) += pwm-samsung.o
obj-$(CONFIG_PWM_SIFIVE) += pwm-sifive.o
new file mode 100644
@@ -0,0 +1,444 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Renesas RZ/G2L General PWM Timer (GPT) driver
+ *
+ * Copyright (C) 2024 Renesas Electronics Corporation
+ *
+ * Hardware manual for this IP can be found here
+ * https://www.renesas.com/eu/en/document/mah/rzg2l-group-rzg2lc-group-users-manual-hardware-0?language=en
+ *
+ * Limitations:
+ * - Counter must be stopped before modifying Mode and Prescaler.
+ * - When PWM is disabled, the output is driven to inactive.
+ * - While the hardware supports both polarities, the driver (for now)
+ * only handles normal polarity.
+ * - General PWM Timer (GPT) has 8 HW channels for PWM operations and
+ * each HW channel have 2 IOs.
+ * - Each IO is modelled as an independent PWM channel.
+ * - When both channels are used, disabling the channel on one stops the
+ * other.
+ * - When both channels are used, the period of both IOs in the HW channel
+ * must be same (for now).
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/limits.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pwm.h>
+#include <linux/reset.h>
+#include <linux/time.h>
+#include <linux/units.h>
+
+#define RZG2L_GET_CH(hwpwm) ((hwpwm) / 2)
+#define RZG2L_GET_CH_OFFS(ch) (0x100 * (ch))
+
+#define RZG2L_GTCR(ch) (0x2c + RZG2L_GET_CH_OFFS(ch))
+#define RZG2L_GTUDDTYC(ch) (0x30 + RZG2L_GET_CH_OFFS(ch))
+#define RZG2L_GTIOR(ch) (0x34 + RZG2L_GET_CH_OFFS(ch))
+#define RZG2L_GTBER(ch) (0x40 + RZG2L_GET_CH_OFFS(ch))
+#define RZG2L_GTCNT(ch) (0x48 + RZG2L_GET_CH_OFFS(ch))
+#define RZG2L_GTCCR(ch, sub_ch) (0x4c + RZG2L_GET_CH_OFFS(ch) + 4 * (sub_ch))
+#define RZG2L_GTPR(ch) (0x64 + RZG2L_GET_CH_OFFS(ch))
+
+#define RZG2L_GTCR_CST BIT(0)
+#define RZG2L_GTCR_MD GENMASK(18, 16)
+#define RZG2L_GTCR_TPCS GENMASK(26, 24)
+
+#define RZG2L_GTCR_MD_SAW_WAVE_PWM_MODE FIELD_PREP(RZG2L_GTCR_MD, 0)
+
+#define RZG2L_GTUDDTYC_UP BIT(0)
+#define RZG2L_GTUDDTYC_UDF BIT(1)
+#define RZG2L_GTUDDTYC_UP_COUNTING (RZG2L_GTUDDTYC_UP | RZG2L_GTUDDTYC_UDF)
+
+#define RZG2L_GTIOR_GTIOA GENMASK(4, 0)
+#define RZG2L_GTIOR_GTIOB GENMASK(20, 16)
+#define RZG2L_GTIOR_GTIOx(sub_ch) ((sub_ch) ? RZG2L_GTIOR_GTIOB : RZG2L_GTIOR_GTIOA)
+#define RZG2L_GTIOR_OAE BIT(8)
+#define RZG2L_GTIOR_OBE BIT(24)
+#define RZG2L_GTIOR_OxE(sub_ch) ((sub_ch) ? RZG2L_GTIOR_OBE : RZG2L_GTIOR_OAE)
+
+#define RZG2L_INIT_OUT_HI_OUT_HI_END_TOGGLE 0x1b
+#define RZG2L_GTIOR_GTIOA_OUT_HI_END_TOGGLE_CMP_MATCH \
+ (RZG2L_INIT_OUT_HI_OUT_HI_END_TOGGLE | RZG2L_GTIOR_OAE)
+#define RZG2L_GTIOR_GTIOB_OUT_HI_END_TOGGLE_CMP_MATCH \
+ (FIELD_PREP(RZG2L_GTIOR_GTIOB, RZG2L_INIT_OUT_HI_OUT_HI_END_TOGGLE) | RZG2L_GTIOR_OBE)
+
+#define RZG2L_GTIOR_GTIOx_OUT_HI_END_TOGGLE_CMP_MATCH(sub_ch) \
+ ((sub_ch) ? RZG2L_GTIOR_GTIOB_OUT_HI_END_TOGGLE_CMP_MATCH : \
+ RZG2L_GTIOR_GTIOA_OUT_HI_END_TOGGLE_CMP_MATCH)
+
+#define RZG2L_MAX_HW_CHANNELS 8
+#define RZG2L_CHANNELS_PER_IO 2
+#define RZG2L_MAX_PWM_CHANNELS (RZG2L_MAX_HW_CHANNELS * RZG2L_CHANNELS_PER_IO)
+#define RZG2L_MAX_SCALE_FACTOR 1024
+#define RZG2L_MAX_TICKS ((u64)U32_MAX * RZG2L_MAX_SCALE_FACTOR)
+
+struct rzg2l_gpt_chip {
+ void __iomem *mmio;
+ struct mutex lock; /* lock to protect shared channel resources */
+ unsigned long rate_khz;
+ u32 period_ticks[RZG2L_MAX_HW_CHANNELS];
+ u32 channel_request_count[RZG2L_MAX_HW_CHANNELS];
+ u32 channel_enable_count[RZG2L_MAX_HW_CHANNELS];
+};
+
+static inline struct rzg2l_gpt_chip *to_rzg2l_gpt_chip(struct pwm_chip *chip)
+{
+ return pwmchip_get_drvdata(chip);
+}
+
+static inline unsigned int rzg2l_gpt_subchannel(unsigned int hwpwm)
+{
+ return hwpwm & 0x1;
+}
+
+static void rzg2l_gpt_write(struct rzg2l_gpt_chip *rzg2l_gpt, u32 reg, u32 data)
+{
+ writel(data, rzg2l_gpt->mmio + reg);
+}
+
+static u32 rzg2l_gpt_read(struct rzg2l_gpt_chip *rzg2l_gpt, u32 reg)
+{
+ return readl(rzg2l_gpt->mmio + reg);
+}
+
+static void rzg2l_gpt_modify(struct rzg2l_gpt_chip *rzg2l_gpt, u32 reg, u32 clr,
+ u32 set)
+{
+ rzg2l_gpt_write(rzg2l_gpt, reg,
+ (rzg2l_gpt_read(rzg2l_gpt, reg) & ~clr) | set);
+}
+
+static u8 rzg2l_gpt_calculate_prescale(struct rzg2l_gpt_chip *rzg2l_gpt,
+ u64 period_ticks)
+{
+ u32 prescaled_period_ticks;
+ u8 prescale;
+
+ prescaled_period_ticks = period_ticks >> 32;
+ if (prescaled_period_ticks >= 256)
+ prescale = 5;
+ else
+ prescale = (fls(prescaled_period_ticks) + 1) / 2;
+
+ return prescale;
+}
+
+static int rzg2l_gpt_request(struct pwm_chip *chip, struct pwm_device *pwm)
+{
+ struct rzg2l_gpt_chip *rzg2l_gpt = to_rzg2l_gpt_chip(chip);
+ u32 ch = RZG2L_GET_CH(pwm->hwpwm);
+
+ guard(mutex)(&rzg2l_gpt->lock);
+ rzg2l_gpt->channel_request_count[ch]++;
+
+ return 0;
+}
+
+static void rzg2l_gpt_free(struct pwm_chip *chip, struct pwm_device *pwm)
+{
+ struct rzg2l_gpt_chip *rzg2l_gpt = to_rzg2l_gpt_chip(chip);
+ u32 ch = RZG2L_GET_CH(pwm->hwpwm);
+
+ guard(mutex)(&rzg2l_gpt->lock);
+ rzg2l_gpt->channel_request_count[ch]--;
+}
+
+static bool rzg2l_gpt_is_ch_enabled(struct rzg2l_gpt_chip *rzg2l_gpt, u8 hwpwm)
+{
+ u8 ch = RZG2L_GET_CH(hwpwm);
+ u32 val;
+
+ val = rzg2l_gpt_read(rzg2l_gpt, RZG2L_GTCR(ch));
+ if (!(val & RZG2L_GTCR_CST))
+ return false;
+
+ val = rzg2l_gpt_read(rzg2l_gpt, RZG2L_GTIOR(ch));
+
+ return val & RZG2L_GTIOR_OxE(rzg2l_gpt_subchannel(hwpwm));
+}
+
+/* Caller holds the lock while calling rzg2l_gpt_enable() */
+static void rzg2l_gpt_enable(struct rzg2l_gpt_chip *rzg2l_gpt,
+ struct pwm_device *pwm)
+{
+ u8 sub_ch = rzg2l_gpt_subchannel(pwm->hwpwm);
+ u32 val = RZG2L_GTIOR_GTIOx(sub_ch) | RZG2L_GTIOR_OxE(sub_ch);
+ u8 ch = RZG2L_GET_CH(pwm->hwpwm);
+
+ /* Enable pin output */
+ rzg2l_gpt_modify(rzg2l_gpt, RZG2L_GTIOR(ch), val,
+ RZG2L_GTIOR_GTIOx_OUT_HI_END_TOGGLE_CMP_MATCH(sub_ch));
+
+ if (!rzg2l_gpt->channel_enable_count[ch])
+ rzg2l_gpt_modify(rzg2l_gpt, RZG2L_GTCR(ch), 0, RZG2L_GTCR_CST);
+
+ rzg2l_gpt->channel_enable_count[ch]++;
+}
+
+/* Caller holds the lock while calling rzg2l_gpt_disable() */
+static void rzg2l_gpt_disable(struct rzg2l_gpt_chip *rzg2l_gpt,
+ struct pwm_device *pwm)
+{
+ u8 sub_ch = rzg2l_gpt_subchannel(pwm->hwpwm);
+ u8 ch = RZG2L_GET_CH(pwm->hwpwm);
+
+ /* Stop count, Output low on GTIOCx pin when counting stops */
+ rzg2l_gpt->channel_enable_count[ch]--;
+
+ if (!rzg2l_gpt->channel_enable_count[ch])
+ rzg2l_gpt_modify(rzg2l_gpt, RZG2L_GTCR(ch), RZG2L_GTCR_CST, 0);
+
+ /* Disable pin output */
+ rzg2l_gpt_modify(rzg2l_gpt, RZG2L_GTIOR(ch), RZG2L_GTIOR_OxE(sub_ch), 0);
+}
+
+static u64 rzg2l_gpt_calculate_period_or_duty(struct rzg2l_gpt_chip *rzg2l_gpt,
+ u32 val, u8 prescale)
+{
+ u64 tmp;
+
+ /*
+ * The calculation doesn't overflow an u64 because prescale ≤ 5 and so
+ * tmp = val << (2 * prescale) * USEC_PER_SEC
+ * < 2^32 * 2^10 * 10^6
+ * < 2^32 * 2^10 * 2^20
+ * = 2^62
+ */
+ tmp = (u64)val << (2 * prescale);
+ tmp *= USEC_PER_SEC;
+
+ return DIV64_U64_ROUND_UP(tmp, rzg2l_gpt->rate_khz);
+}
+
+static int rzg2l_gpt_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
+ struct pwm_state *state)
+{
+ struct rzg2l_gpt_chip *rzg2l_gpt = to_rzg2l_gpt_chip(chip);
+
+ state->enabled = rzg2l_gpt_is_ch_enabled(rzg2l_gpt, pwm->hwpwm);
+ if (state->enabled) {
+ u32 sub_ch = rzg2l_gpt_subchannel(pwm->hwpwm);
+ u32 ch = RZG2L_GET_CH(pwm->hwpwm);
+ u8 prescale;
+ u32 val;
+
+ val = rzg2l_gpt_read(rzg2l_gpt, RZG2L_GTCR(ch));
+ prescale = FIELD_GET(RZG2L_GTCR_TPCS, val);
+
+ val = rzg2l_gpt_read(rzg2l_gpt, RZG2L_GTPR(ch));
+ state->period = rzg2l_gpt_calculate_period_or_duty(rzg2l_gpt, val, prescale);
+
+ val = rzg2l_gpt_read(rzg2l_gpt, RZG2L_GTCCR(ch, sub_ch));
+ state->duty_cycle = rzg2l_gpt_calculate_period_or_duty(rzg2l_gpt, val, prescale);
+ if (state->duty_cycle > state->period)
+ state->duty_cycle = state->period;
+ }
+
+ state->polarity = PWM_POLARITY_NORMAL;
+
+ return 0;
+}
+
+static u32 rzg2l_gpt_calculate_pv_or_dc(u64 period_or_duty_cycle, u8 prescale)
+{
+ return min_t(u64, DIV_ROUND_DOWN_ULL(period_or_duty_cycle, 1 << (2 * prescale)),
+ U32_MAX);
+}
+
+/* Caller holds the lock while calling rzg2l_gpt_config() */
+static int rzg2l_gpt_config(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state)
+{
+ struct rzg2l_gpt_chip *rzg2l_gpt = to_rzg2l_gpt_chip(chip);
+ u8 sub_ch = rzg2l_gpt_subchannel(pwm->hwpwm);
+ u8 ch = RZG2L_GET_CH(pwm->hwpwm);
+ u64 period_ticks, duty_ticks;
+ unsigned long pv, dc;
+ u8 prescale;
+
+ /* Limit period/duty cycle to max value supported by the HW */
+ period_ticks = mul_u64_u64_div_u64(state->period, rzg2l_gpt->rate_khz, USEC_PER_SEC);
+ if (period_ticks > RZG2L_MAX_TICKS)
+ period_ticks = RZG2L_MAX_TICKS;
+ /*
+ * GPT counter is shared by the two IOs of a single channel, so
+ * prescale and period can NOT be modified when there are multiple IOs
+ * in use with different settings.
+ */
+ if (rzg2l_gpt->channel_request_count[ch] > 1 && period_ticks != rzg2l_gpt->period_ticks[ch])
+ return -EBUSY;
+
+ prescale = rzg2l_gpt_calculate_prescale(rzg2l_gpt, period_ticks);
+ pv = rzg2l_gpt_calculate_pv_or_dc(period_ticks, prescale);
+
+ duty_ticks = mul_u64_u64_div_u64(state->duty_cycle, rzg2l_gpt->rate_khz, USEC_PER_SEC);
+ if (duty_ticks > RZG2L_MAX_TICKS)
+ duty_ticks = RZG2L_MAX_TICKS;
+ dc = rzg2l_gpt_calculate_pv_or_dc(duty_ticks, prescale);
+
+ /*
+ * GPT counter is shared by multiple channels, we cache the period ticks
+ * from the first enabled channel and use the same value for both
+ * channels.
+ */
+ rzg2l_gpt->period_ticks[ch] = period_ticks;
+
+ /*
+ * Counter must be stopped before modifying mode, prescaler, timer
+ * counter and buffer enable registers. These registers are shared
+ * between both channels. So allow updating these registers only for the
+ * first enabled channel.
+ */
+ if (rzg2l_gpt->channel_enable_count[ch] <= 1) {
+ rzg2l_gpt_modify(rzg2l_gpt, RZG2L_GTCR(ch), RZG2L_GTCR_CST, 0);
+
+ /* GPT set operating mode (saw-wave up-counting) */
+ rzg2l_gpt_modify(rzg2l_gpt, RZG2L_GTCR(ch), RZG2L_GTCR_MD,
+ RZG2L_GTCR_MD_SAW_WAVE_PWM_MODE);
+
+ /* Set count direction */
+ rzg2l_gpt_write(rzg2l_gpt, RZG2L_GTUDDTYC(ch), RZG2L_GTUDDTYC_UP_COUNTING);
+
+ /* Select count clock */
+ rzg2l_gpt_modify(rzg2l_gpt, RZG2L_GTCR(ch), RZG2L_GTCR_TPCS,
+ FIELD_PREP(RZG2L_GTCR_TPCS, prescale));
+
+ /* Set period */
+ rzg2l_gpt_write(rzg2l_gpt, RZG2L_GTPR(ch), pv);
+ }
+
+ /* Set duty cycle */
+ rzg2l_gpt_write(rzg2l_gpt, RZG2L_GTCCR(ch, sub_ch), dc);
+
+ if (rzg2l_gpt->channel_enable_count[ch] <= 1) {
+ /* Set initial value for counter */
+ rzg2l_gpt_write(rzg2l_gpt, RZG2L_GTCNT(ch), 0);
+
+ /* Set no buffer operation */
+ rzg2l_gpt_write(rzg2l_gpt, RZG2L_GTBER(ch), 0);
+
+ /* Restart the counter after updating the registers */
+ rzg2l_gpt_modify(rzg2l_gpt, RZG2L_GTCR(ch),
+ RZG2L_GTCR_CST, RZG2L_GTCR_CST);
+ }
+
+ return 0;
+}
+
+static int rzg2l_gpt_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state)
+{
+ struct rzg2l_gpt_chip *rzg2l_gpt = to_rzg2l_gpt_chip(chip);
+ bool enabled = pwm->state.enabled;
+ int ret;
+
+ if (state->polarity != PWM_POLARITY_NORMAL)
+ return -EINVAL;
+
+ guard(mutex)(&rzg2l_gpt->lock);
+ if (!state->enabled) {
+ if (enabled)
+ rzg2l_gpt_disable(rzg2l_gpt, pwm);
+
+ return 0;
+ }
+
+ ret = rzg2l_gpt_config(chip, pwm, state);
+ if (!ret && !enabled)
+ rzg2l_gpt_enable(rzg2l_gpt, pwm);
+
+ return ret;
+}
+
+static const struct pwm_ops rzg2l_gpt_ops = {
+ .request = rzg2l_gpt_request,
+ .free = rzg2l_gpt_free,
+ .get_state = rzg2l_gpt_get_state,
+ .apply = rzg2l_gpt_apply,
+};
+
+static int rzg2l_gpt_probe(struct platform_device *pdev)
+{
+ struct rzg2l_gpt_chip *rzg2l_gpt;
+ struct device *dev = &pdev->dev;
+ struct reset_control *rstc;
+ struct pwm_chip *chip;
+ unsigned long rate;
+ struct clk *clk;
+ int ret;
+ u32 i;
+
+ chip = devm_pwmchip_alloc(dev, RZG2L_MAX_PWM_CHANNELS, sizeof(*rzg2l_gpt));
+ if (IS_ERR(chip))
+ return PTR_ERR(chip);
+ rzg2l_gpt = to_rzg2l_gpt_chip(chip);
+
+ rzg2l_gpt->mmio = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(rzg2l_gpt->mmio))
+ return PTR_ERR(rzg2l_gpt->mmio);
+
+ rstc = devm_reset_control_get_exclusive_deasserted(dev, NULL);
+ if (IS_ERR(rstc))
+ return dev_err_probe(dev, PTR_ERR(rstc), "Cannot deassert reset control\n");
+
+ clk = devm_clk_get_enabled(dev, NULL);
+ if (IS_ERR(clk))
+ return dev_err_probe(dev, PTR_ERR(clk), "Cannot get clock\n");
+
+ ret = devm_clk_rate_exclusive_get(dev, clk);
+ if (ret)
+ return ret;
+
+ rate = clk_get_rate(clk);
+ if (!rate)
+ return dev_err_probe(dev, -EINVAL, "The gpt clk rate is 0");
+
+ /*
+ * Refuse clk rates > 1 GHz to prevent overflow later for computing
+ * period and duty cycle.
+ */
+ if (rate > NSEC_PER_SEC)
+ return dev_err_probe(dev, -EINVAL, "The gpt clk rate is > 1GHz");
+
+ /*
+ * Rate is in MHz and is always integer for peripheral clk
+ * 2^32 * 2^10 (prescalar) * 10^6 (rate_khz) < 2^64
+ * So make sure rate is multiple of 1000.
+ */
+ rzg2l_gpt->rate_khz = rate / KILO;
+ if (rzg2l_gpt->rate_khz * KILO != rate)
+ return dev_err_probe(dev, -EINVAL, "Rate is not multiple of 1000");
+
+ mutex_init(&rzg2l_gpt->lock);
+
+ chip->ops = &rzg2l_gpt_ops;
+ ret = devm_pwmchip_add(dev, chip);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to add PWM chip\n");
+
+ return 0;
+}
+
+static const struct of_device_id rzg2l_gpt_of_table[] = {
+ { .compatible = "renesas,rzg2l-gpt", },
+ { /* Sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rzg2l_gpt_of_table);
+
+static struct platform_driver rzg2l_gpt_driver = {
+ .driver = {
+ .name = "pwm-rzg2l-gpt",
+ .of_match_table = rzg2l_gpt_of_table,
+ },
+ .probe = rzg2l_gpt_probe,
+};
+module_platform_driver(rzg2l_gpt_driver);
+
+MODULE_AUTHOR("Biju Das <biju.das.jz@bp.renesas.com>");
+MODULE_DESCRIPTION("Renesas RZ/G2L General PWM Timer (GPT) Driver");
+MODULE_LICENSE("GPL");
RZ/G2L General PWM Timer (GPT) composed of 8 channels with 32-bit timer (GPT32E). It supports the following functions * 32 bits x 8 channels * Up-counting or down-counting (saw waves) or up/down-counting (triangle waves) for each counter. * Clock sources independently selectable for each channel * Two I/O pins per channel * Two output compare/input capture registers per channel * For the two output compare/input capture registers of each channel, four registers are provided as buffer registers and are capable of operating as comparison registers when buffering is not in use. * In output compare operation, buffer switching can be at crests or troughs, enabling the generation of laterally asymmetric PWM waveforms. * Registers for setting up frame cycles in each channel (with capability for generating interrupts at overflow or underflow) * Generation of dead times in PWM operation * Synchronous starting, stopping and clearing counters for arbitrary channels * Starting, stopping, clearing and up/down counters in response to input level comparison * Starting, clearing, stopping and up/down counters in response to a maximum of four external triggers * Output pin disable function by dead time error and detected short-circuits between output pins * A/D converter start triggers can be generated (GPT32E0 to GPT32E3) * Enables the noise filter for input capture and external trigger operation Add basic pwm support for RZ/G2L GPT driver by creating separate logical channels for each IOs. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> --- v22->v23: * Updated Limitation section supporting only same period for both IOs of a hardware channel. * Updated parameter of RZG2L_GET_CH from a->hwpwm * Updated parameter of RZG2L_GET_CH_OFFS from i->ch * Updated parameter of RZG2L_GTIOR_{GTIOx,OxE,OUT_HI_END_TOGGLE_CMP_MATCH from a->sub_ch * Replaced variables user_count->channel_request_count and enable_count->channel_enable_count in struct rzg2l_gpt_chip. * Added missing prefix for calculate_period_or_duty(). * Updated comment section in rzg2l_gpt_config() * Added check for period in rzg2l_gpt_config() and return error if there is mismatch in period of both IOs. * Started using devm_reset_control_get_exclusive_deasserted() and dropped rzg2l_gpt_reset_assert() * Dropped unnecessary bootloader enabled channel code from probe. * All error messages now start with a capital letter. v21->v22: * Started using guard(mutex)calls. * Replaced round up->down operation in rzg2l_gpt_calculate_pv_or_dc() as it converts a nanosecond value to a register value. * Replaced devm_clk_get->devm_clk_get_enabled() to make clock on during the lifetime of driver and get rid of bootloader_enabled_channels variable. Also dropped rzg2l_gpt_rpm_put(), pm_runtime.h header and pm runtime calls, that simplified the probe() and other functions. * Replaced return type of the rzg2l_gpt_enable() as void as it is not returning any error. * Dropped lock from enable() and disable() as caller is holding the lock. this way we won't release the lock just to allow a called function to retake it. v20->v21: * Added documentation about the relation between channels and outputs and subchannels. * Dropped using the local variable offs for calculating channel regs and instead start using macros. * Replaced u8->bool for the bootloader_enabled_channels variable in struct rzg2l_gpt_chip * Replaced duty_cycles->duty_ticks and period_cycles->period_ticks as it represent hw ticks. * Introduced RZG2L_MAX_TICKS macro for max hw ticks and dropped the variable max_val from struct rzg2l_gpt_chip. * Updated comment related to 64-bit overflow calculation in calculate_period_or_duty(). * Simplified handling of bootloader_enabled_channels[pwm->hwpwm] == true in a single place in rzg2l_gpt_apply() * For config error case, don't call pm_runtime_put_sync() and with enable()->acquire pm_runtime reference and disable()-->release the pm_runtime reference * Split the cleanups into two. One for reset_control_deassert() earlier in .probe() and dropped rstc variable from struct rzg2l_gpt_chip. * Added warn_once() message in probe() for bootloader setting wrong prescale values. v19->v20: * Added locks for rmw operations in rzg2l_gpt_{en,dis}able(). * Dropped decremeng enable_count based ch_en_bits in rzg2l_gpt_disable(). * Added a comment in calculate_period_or_duty() related to overflow. * Replaced ch_en_bits->bootloader_enabled_channels and used this variable in probe(), apply() and remove() for simplification * Replaced pm_runtime_enable()->devm_pm_runtime_enable() v18->v19: * Replaced RZG2L_UP_COUNTING->RZG2L_GTUDDTYC_UP_COUNTING macro. * Aligned RZG2L_GET_CH and RZG2L_GET_CH_OFFS macro * Dropped chip and clk from struct rzg2l_gpt_chip as started using devm_pwmchip_alloc() and devm_clk_rate_exclusive_get() to replace it. * Replaced rate->rate_khz in struct rzg2l_gpt_chip and added a check in probe() to make sure rate is multiple of 1000. * Replaced container_of->pwmchip_get_drvdata() to get device data. * Added a check in rzg2l_gpt_disable() not to decrement enable_count if ch_en_bits is set by the probe. * Dropped rzg2l_gpt_mul_u64_u64_div_u64() * Simplified calculate_period_or_duty() using rate_khz * Simplified rzg2l_gpt_config() using min macro for calculating period and duty_cycle. * Added checks in rzg2l_gpt_config() to prevent second channel setting shared register. * Updated error handling rzg2l_gpt_apply() * Added local variable dev for &pdev->dev in probe() * Added local varibles rate, chip and clk in probe() * Dropped err_clk_rate_put label as started using devm_clk_rate_exclusive_get() * Replaced rzg2l_gpt->chip as data for devm_add_action_or_reset(). * Added error message for rate > 1GHz in probe. v17->v18: * Updated copyright from 2023->2024. * Added units.h for KILO macro. * Replaced RZG2L_GTCCR{A,B}->RZG2L_GTCCR(i) * Introduced macros RZG2L_GTIOR_{GTIOx,OxE} to handle subchannels. * Replaced RZG2L_IS_IOB()->rzg2l_gpt_subchannel() * Replaced the cache period->period_cycles. * Updated rzg2l_gpt_is_ch_enabled() to return early if counter is not running. * Updated calculate_period_or_duty() for avoiding overflows. * Updated rzg2l_gpt_calculate_pv_or_dc() with simplified calculation for DIV64_U64_ROUND_UP() and dropped the cast for U32_MAX in min_t. * Replaced mul_u64_u32_div->rzg2l_gpt_mul_u64_u64_div_u64() helper. * Dropped pm pointer from struct rzg2l_gpt_driver() and simplified clk handling in probe(). v16->v17: * Added ret = dev_err_probe() to avoid return success in probe(). * Dropped unneeded MODULE_ALIAS(). * Dropped .owner from struct rzg2l_gpt_ops. * Fixed build issue reported by kernel test robot <lkp@intel.com> by replacing DIV_ROUND_UP()->DIV64_U64_ROUND_UP() in rzg2l_gpt_calculate_pv_or_dc(). * Added max_val to struct rzg2l_gpt_chip to compute maximum period supported by the HW in probe() and limit its value in apply() to avoid 64-bit overflow with computation. * Added helper function calculate_period_or_duty() to avoid losing precision for smaller period/duty cycle values ((2^32 * 10^9 << 2) < 2^64), by not processing the rounded values. * Replaced mul_u64_u64_div_u64()->mul_u64_u32_div() as the former is giving warnings with CONFIG_PWM_DEBUG enabled for very high values. eg: echo "###### Medium setting 11000 sec = 3hours ##" echo 11000000000000 > /sys/class/pwm/$PWMCHIP/pwm${IO_1}/period echo 5500000000000 > /sys/class/pwm/$PWMCHIP/pwm${IO_1}/duty_cycle dumpgptreg echo "###### High setting##" echo 43980465100800 > /sys/class/pwm/$PWMCHIP/pwm${IO_1}/period echo 23980465100800 > /sys/class/pwm/$PWMCHIP/pwm${IO_1}/duty_cycle dumpgptreg with mul_u64_u32_div(): ###### Medium setting 11000 sec = 3hours ## Read at address 0x10048464 (0xffffb9426464): 0x400746FE Read at address 0x1004844C (0xffff8fdfb44c): 0x2003A37F Read at address 0x1004842C (0xffff9855b42c): 0x05000001 ###### High setting## Read at address 0x10048464 (0xffff9101b464): 0xFFFFFFFF Read at address 0x1004844C (0xffffaee0544c): 0x8B95AD77 Read at address 0x1004842C (0xffffbbc8a42c): 0x05000001 with mul_u64_u64_div_u64(): ###### Medium setting 11000 sec = 3hours ## Read at address 0x10048464 (0xffffb3185464): 0x400746FE Read at address 0x1004844C (0xffff81ebb44c): 0x2003A37F Read at address 0x1004842C (0xffff904fd42c): 0x05000001 ######[ 304.213944] pwm-rzg2l-gpt 10048000.pwm: .apply is not idempotent (ena=1 pol=0 5500000000000/43980352512000) -> (ena=1 pol=0 5500000000000/43980239923200) High setting## [ 304.230854] pwm-rzg2l-gpt 10048000.pwm: .apply is not idempotent (ena=1 pol=0 23980465100800/43980352512000) -> (ena=1 pol=0 23980465100800/43980239923200) Read at address 0x10048464 (0xffffb5bb3464): 0xFFFFAA19 Read at address 0x1004844C (0xffff99b8c44c): 0x8B95AD77 Read at address 0x1004842C (0xffffbba2342c): 0x05000001 v15->v16: * Replaced the macro DIV_ROUND_UP_ULL->DIV64_U64_ROUND_UP * Added DIV_ROUND_UP in rzg2l_gpt_calculate_pv_or_dc() to avoid loss of precision. * Replaced min->min_t() in rzg2l_gpt_calculate_pv_or_dc(). * Added a comment for rzg2l_gpt_config() * Replaced mul_u64_u32_div()->mul_u64_u64_div_u64() in rzg2l_gpt_config() * Fixed the logical condition related to counter stop in rzg2l_gpt_config(). * Dropped pm_runtime_resume_*() from rzg2l_gpt_config() as it is managed by rzg2l_gpt_apply(). * Moved pm_runtime_resume_*() from rzg2l_gpt_{en,dis}able() to rzg2l_gpt_apply(). v14->v15: * Added enable_count and ch_en_bits variables to struct rzg2l_gpt_chip based on feedback for pwm_mtu3 driver. * Updated copyright header and commit description by replacing "This patch adds"-> "Add" * Replaced macro RZG2L_GET_CH_INDEX->RZG2L_GET_CH and replaced ch_index->ch throughout * rzg2l_gpt_{enable,disable}() enables/disables PWM based on the enable_count. * Replaced pm_runtime_get_sync->pm_runtime_resume_and_get and propogated the error in rzg2l_gpt_get_state() and rzg2l_gpt_config() * Reduced variable scope in rzg2l_gpt_get_state() by moving most of variables inside the if statement. * Updated rzg2l_gpt_get_state() by moving duty > period check inside the top if block. * Added helper functions rzg2l_gpt_calculate_pv_or_dc()to simplify config. Also Improved the logic in rzg2l_gpt_calculate_pv_or_dc() by using min(period_or_duty_cycle >> (2 * prescale), (u64)U32_MAX); * Updated rzg2l_gpt_get_state() by moving duty > period check inside the top if block. * Simplified rzg2l_gpt_config() for updating registers * Dropped pm_runtime_get_sync() and used bitmap variable "ch_en_bits" to make balanced PM usage count in rzg2l_gpt_reset_assert_pm_disable() For case were unbind is called before apply where pwm is enabled by bootloader. * Added error check for clk_rate_exclusive_get() and clk_get_rate() in probe(). * Dropped prescale from struct rzg2l_gpt_chip. * Replaced of_match_ptr(rzg2l_gpt_of_table)->rzg2l_gpt_of_table in struct rzg2l_gpt_driver v13->v14: * Removed parenthesis for RZG2L_MAX_HW_CHANNELS and RZG2L_CHANNELS_PER_IO * Removed duty_cycle variable from struct rzg2l_gpt_chip and added comment for cache for prescale variable. * Fixed a bug in rzg2l_gpt_cntr_need_stop(). * Reordered rzg2l_gpt_config() just above apply() * Replaced pwm_is_enabled()->pwm->state.enabled in config * Replaced pm_runtime_resume_and_get with unconditional pm_runtime_get_sync() in config(). * Restored duty_cycle > period check in rzg2l_gpt_get_state(). * Added error check for clk_prepare_enable() in probe() and propagating error to the caller for pm_runtime_resume() * clk_get_rate() is called after enabling the clock and clk_rate_exclusive_get() * Simplified rzg2l_gpt_probe() by removing bitmap variables. * Added pm_runtime_idle() to suspend the device during probe. * Moved overflow condition check from config->probe(). * Simplified rzg2l_gpt_reset_assert_pm_disable(). v12->v13: * Replaced Kconfig dependency from ARCH_RENESAS->ARCH_RZG2L * Sorted #include <linux/limits.h> alphabetically * Added a comment for mutex_lock to fix check patch warning * Replaced data type of duty_cycle from unsigned int->u32 as the maximum value stored is U32_MAX. * Improved rzg2l_gpt_config() by removing unwanted duty_cycle related code. * Improved rzg2l_gpt_get_state() by setting "val = rzg2l_gpt->duty_cycle[pwm->hwpwm];", and factor "tmp = NSEC_PER_SEC * (u64)val;" out of the if-statement. * Started using DEFINE_RUNTIME_DEV_PM_OPS(), and dropped __maybe_unused from the callbacks. v11->v12: * Added return code for get_state() * Cache duty cycle/prescale as the driver cannot read the current duty cycle/prescale from the hardware if the hardware is disabled. Cache the last programmed duty cycle/prescale value to return in that case. * Updated rzg2l_gpt_enable to enable the clocks. * Updated rzg2l_gpt_disable to disable the clocks. * Updated rzg2l_gpt_config() to cache duty cucle/prescale value * Updated rzg2l_gpt_get_state to use cached value of duty cycle/prescale,If the PWM is disabled. * Simplified rzg2l_gpt_apply() * Added comments in rzg2l_gpt_reset_assert_pm_disable() v10->v11: * Used bitmap_zero for initializing bitmap varable. * Fixed clock imbalance during remove for the case bootloader turning on PWM and module unload is called just after the boot. * Fixed over flow condition in get_state() for a prescale value of 2 & more. * Improved rzg2l_gpt_cntr_need_stop() based on prescale as it is the only runtime variable. * Added array for Cache variables state_period and prescale * Probe caches the prescale value set by the bootloader. * Updated rzg2l_gpt_config() to make use of array variables. v9->v10: * Updated the error handling in probe(), clk_disable_unprepare called on the error path. * Removed ch_en array and started using bitmask instead. v8->v9: * deassert after devm_clk_get() to avoid reset stays deasserted,in case clk_get() fails. * Removed ch_offs from struct rzg2l_gpt_chip and use macro instead. * Updated error handling in probe() v7->v8: * Modelled as single PWM device handling multiple channels * Replaced shared reset->devm_reset_control_get_exclusive() * Replaced iowrite32->writel and ioread32->readl * Updated prescale calculation * Added PM runtime callbacks * Updated PM handling and removed "pwm_enabled_by_bootloader" variable * Introduced rzg2l_gpt_is_ch_enabled for checking enable status on both IO's * Moved enable/disable output pins from config->enable/disable. * Added rzg2l_gpt_cntr_need_stop() for caching prescalar/mode values. v6->v7: * Added the comment for cacheing rzg2l_gpt->state_period. * Fixed boundary values for pv and dc. * Added comment for modifying mode, prescaler, timer counter and buffer enable registers. * Fixed buffer overflow in get_state() * Removed unnecessary assignment of state->period value in get_state(). * Fixed state->duty_cycle value in get_state(). * Added a limitation for disabling the channels. v5->v6: * Updated macros RZG2L_GTIOR_GTIOB_OUT_HI_END_TOGGLE_CMP_MATCH and RZG2L_GTIOR_GTIOB_OUT_LO_END_TOGGLE_CMP_MATCH with computation involving FIELD_PREP macro. * Removed struct rzg2l_gpt_phase and started using RZG2L_GTCCR macro for duty_offset. * replaced misnomer real_period->state_period. * Added handling for values >= (1024 << 32) for both period and duty cycle. * Added comments for pwm {en,dis}abled by bootloader during probe. v4->v5: * Added Hardware manual details * Replaced the comment GTCNT->Counter * Removed the macros RZG2L_GPT_IO_PER_CHANNEL and chip.npwm directly used in probe. * Removed the unsed macro RZG2L_GTPR_MAX_VALUE * Added driver prefix for the type name and the variable. * Initialization of per_channel data moved from request->probe. * Updated clr parameter for rzg2l_gpt_modify for Start count. * Started using mutex and usage_count for handling shared period and prescalar for the 2 channels. * Updated the comment cycle->period. * Removed clk_disable from rzg2l_gpt_reset_assert_pm_disable() * Replaced pc->rzg2l_gpt. * Updated prescale calculation. * Moved pm_runtime_{get_sync,put} from {request,free}->{enable,disable} * Removed platform_set_drvdata as it is unused * Removed the variable pwm_enabled_by_bootloader * Added dev_err_probe in various error paths in probe. * Added an error message, if devm_pwmchip_add() fails. v3->v4: * Changed the local variable type i from u16->u8 and prescaled_period_ cycles from u64->u32 in calculate_prescale(). * Replaced mul_u64_u64_div_u64()->mul_u64_u32_div() * Dropped the comma after the sentinel. * Add a variable to track pwm enabled by bootloader and added comments in probe(). * Removed unnecessary rzg2l_gpt_reset_assert_pm_disable() from probe. * Replaced devm_clk_get()->devm_clk_get_prepared() * Removed devm_clk_get_optional_enabled() v2->v3: * Updated limitation section * Added prefix "RZG2L_" for all macros * Modified prescale calculation * Removed pwm_set_chip_data * Updated comment related to modifying Mode and Prescaler * Updated setting of prescale value in rzg2l_gpt_config() * Removed else branch from rzg2l_gpt_get_state() * removed the err label from rzg2l_gpt_apply() * Added devm_clk_get_optional_enabled() to retain clk on status, in case bootloader turns on the clk of pwm. * Replaced devm_reset_control_get_exclusive->devm_reset_control_get_shared as single reset shared between 8 channels. v1->v2: * Added Limitations section * dropped "_MASK" from the define names. * used named initializer for struct phase * Added gpt_pwm_device into a flexible array member in rzg2l_gpt_chip * Revised the logic for prescale * Added .get_state callback * Improved error handling in rzg2l_gpt_apply * Removed .remove callback * Tested driver with PWM_DEBUG enabled RFC->V1: * Updated macros * replaced rzg2l_gpt_write_mask()->rzg2l_gpt_modify() * Added rzg2l_gpt_read() --- drivers/pwm/Kconfig | 11 + drivers/pwm/Makefile | 1 + drivers/pwm/pwm-rzg2l-gpt.c | 444 ++++++++++++++++++++++++++++++++++++ 3 files changed, 456 insertions(+) create mode 100644 drivers/pwm/pwm-rzg2l-gpt.c