@@ -7,6 +7,8 @@
#include "r8a77951.dtsi"
+#undef SOC_HAS_USB2_CH3
+
&audma0 {
iommus = <&ipmmu_mp1 0>, <&ipmmu_mp1 1>,
<&ipmmu_mp1 2>, <&ipmmu_mp1 3>,
@@ -47,44 +47,3 @@ &du {
clock-names = "du.0", "du.1", "du.2", "du.3",
"dclkin.0", "dclkin.1", "dclkin.2", "dclkin.3";
};
-
-&ehci3 {
- dr_mode = "otg";
- status = "okay";
-};
-
-&hsusb3 {
- dr_mode = "otg";
- status = "okay";
-};
-
-&ohci3 {
- dr_mode = "otg";
- status = "okay";
-};
-
-&pfc {
- /*
- * - On Salvator-X[S], GP6_3[01] are connected to ADV7482 as irq pins
- * (when SW31 is the default setting on Salvator-XS).
- * - If SW31 is the default setting, you cannot use USB2.0 ch3 on
- * r8a77951 with Salvator-XS.
- * Hence the SW31 setting must be changed like 2) below.
- * 1) Default setting of SW31: ON-ON-OFF-OFF-OFF-OFF:
- * - Connect GP6_3[01] to ADV7842.
- * 2) Changed setting of SW31: OFF-OFF-ON-ON-ON-ON:
- * - Connect GP6_3[01] to BD082065 (USB2.0 ch3's host power).
- * - Connect GP6_{04,21} to ADV7842.
- */
- usb2_ch3_pins: usb2_ch3 {
- groups = "usb2_ch3";
- function = "usb2_ch3";
- };
-};
-
-&usb2_phy3 {
- pinctrl-0 = <&usb2_ch3_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
@@ -14,6 +14,7 @@
#define SOC_HAS_HDMI1
#define SOC_HAS_SATA
#define SOC_HAS_USB2_CH2
+#define SOC_HAS_USB2_CH3
/ {
compatible = "renesas,r8a7795";
@@ -40,3 +40,46 @@ pcie-sata-switch-hog {
/* SW12-7 must be set 'Off' (MD12 set to 1) which is not the default! */
#endif /* SOC_HAS_SATA */
+
+#ifdef SOC_HAS_USB2_CH3
+&ehci3 {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&hsusb3 {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&ohci3 {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&pfc {
+ /*
+ * - On Salvator-X[S], GP6_3[01] are connected to ADV7482 as irq pins
+ * (when SW31 is the default setting on Salvator-XS).
+ * - If SW31 is the default setting, you cannot use USB2.0 ch3 on
+ * r8a77951 with Salvator-XS.
+ * Hence the SW31 setting must be changed like 2) below.
+ * 1) Default setting of SW31: ON-ON-OFF-OFF-OFF-OFF:
+ * - Connect GP6_3[01] to ADV7842.
+ * 2) Changed setting of SW31: OFF-OFF-ON-ON-ON-ON:
+ * - Connect GP6_3[01] to BD082065 (USB2.0 ch3's host power).
+ * - Connect GP6_{04,21} to ADV7842.
+ */
+ usb2_ch3_pins: usb2_ch3 {
+ groups = "usb2_ch3";
+ function = "usb2_ch3";
+ };
+};
+
+&usb2_phy3 {
+ pinctrl-0 = <&usb2_ch3_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+#endif /* SOC_HAS_USB2_CH3 */
Move the parts related to the fourth USB2 interface on Salvator-XS boards to salvator-xs.dtsi, to avoid future duplication of board descriptions. As this interface is not present on all SoCs that can be found on Salvator-X(S), but only on R-Car H3 ES2.0+, its descriptions are protected by the preprocessor symbol SOC_HAS_USB2_CH3, defined in r8a77951.dtsi, and undefined in r8a77950.dtsi. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> --- arch/arm64/boot/dts/renesas/r8a77950.dtsi | 2 + .../boot/dts/renesas/r8a77951-salvator-xs.dts | 41 ------------------ arch/arm64/boot/dts/renesas/r8a77951.dtsi | 1 + arch/arm64/boot/dts/renesas/salvator-xs.dtsi | 43 +++++++++++++++++++ 4 files changed, 46 insertions(+), 41 deletions(-)