diff mbox series

arm64: dts: rockchip: Add PCIe node on rk3399-roc-pc

Message ID 09300c2d-4298-1b01-ac41-d1b2610589d4@fivetechno.de (mailing list archive)
State New, archived
Headers show
Series arm64: dts: rockchip: Add PCIe node on rk3399-roc-pc | expand

Commit Message

Markus Reichl Oct. 28, 2019, 2:47 p.m. UTC
rk3399-roc-pc has a PCIe interface. Enable it for use with
the M.2 NGFF M_KEY slot on roc-rk3399-mezzanine board.
Tested with Samsung 970 evo plus SSD.

Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
---
 .../arm64/boot/dts/rockchip/rk3399-roc-pc.dts | 38 +++++++++++++++++++
 1 file changed, 38 insertions(+)

Comments

Heiko Stübner Oct. 31, 2019, 4:57 p.m. UTC | #1
Hi,

Am Montag, 28. Oktober 2019, 15:47:27 CET schrieb Markus Reichl:
> rk3399-roc-pc has a PCIe interface. Enable it for use with
> the M.2 NGFF M_KEY slot on roc-rk3399-mezzanine board.
> Tested with Samsung 970 evo plus SSD.
> 
> Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
> ---
>  .../arm64/boot/dts/rockchip/rk3399-roc-pc.dts | 38 +++++++++++++++++++
>  1 file changed, 38 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
> index 9313251765c7..2d637d54994b 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
> @@ -158,6 +158,21 @@
>  		regulator-max-microvolt = <1400000>;
>  		vin-supply = <&vcc_sys>;
>  	};
> +
> +	/* on roc-rk3399-mezzanine board */

I'm undecided on this. From what I've seen that mezzanine board is some
sort of addon, like a raspberry pi hat. Therefore it's not always present,
so probably should not be part of the base board dts.

I'm thinking a dt-overlay that can then be activated might be the solution
of choice, but I've reached out to arm-soc poeple on irc to determine the
correct course.


Heiko

> +	vcc3v3_pcie: vcc3v3-pcie {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc3v3_pcie";
> +		enable-active-high;
> +		gpio = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vcc3v3_pcie_en>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&dc_12v>;
> +	};
>  };
>  
>  &cpu_l0 {
> @@ -514,6 +529,19 @@
>  	status = "okay";
>  };
>  
> +&pcie_phy {
> +	status = "okay";
> +};
> +
> +&pcie0 {
> +	ep-gpios = <&gpio4 RK_PD1 GPIO_ACTIVE_HIGH>;
> +	num-lanes = <4>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie_perst>;
> +	vpcie3v3-supply = <&vcc3v3_pcie>;
> +	status = "okay";
> +};
> +
>  &pinctrl {
>  	lcd-panel {
>  		lcd_panel_reset: lcd-panel-reset {
> @@ -535,6 +563,16 @@
>  		};
>  	};
>  
> +	pcie {
> +		vcc3v3_pcie_en: vcc3v3-pcie-en {
> +			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +		pcie_perst: pcie-perst {
> +			rockchip,pins = <4 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
>  	pmic {
>  		vsel1_gpio: vsel1-gpio {
>  			rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
>
Markus Reichl Oct. 31, 2019, 6:12 p.m. UTC | #2
Hi Heiko,
Am 31.10.19 um 17:57 schrieb Heiko Stuebner:
> Hi,
> 
> Am Montag, 28. Oktober 2019, 15:47:27 CET schrieb Markus Reichl:
>> rk3399-roc-pc has a PCIe interface. Enable it for use with
>> the M.2 NGFF M_KEY slot on roc-rk3399-mezzanine board.
>> Tested with Samsung 970 evo plus SSD.
>> 
>> Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
>> ---
>>  .../arm64/boot/dts/rockchip/rk3399-roc-pc.dts | 38 +++++++++++++++++++
>>  1 file changed, 38 insertions(+)
>> 
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
>> index 9313251765c7..2d637d54994b 100644
>> --- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
>> +++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
>> @@ -158,6 +158,21 @@
>>  		regulator-max-microvolt = <1400000>;
>>  		vin-supply = <&vcc_sys>;
>>  	};
>> +
>> +	/* on roc-rk3399-mezzanine board */
> 
> I'm undecided on this. From what I've seen that mezzanine board is some
> sort of addon, like a raspberry pi hat. Therefore it's not always present,
> so probably should not be part of the base board dts.
> 
> I'm thinking a dt-overlay that can then be activated might be the solution
> of choice, but I've reached out to arm-soc poeple on irc to determine the
> correct course.
> 
I have seen some board.dtsi with board_only.dts respective board_extension.dts
in the arch/arm64/boot/dts/rockchip directory. Would that be ok?

Markus 

> 
> Heiko
> 
>> +	vcc3v3_pcie: vcc3v3-pcie {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vcc3v3_pcie";
>> +		enable-active-high;
>> +		gpio = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&vcc3v3_pcie_en>;
>> +		regulator-always-on;
>> +		regulator-boot-on;
>> +		regulator-min-microvolt = <3300000>;
>> +		regulator-max-microvolt = <3300000>;
>> +		vin-supply = <&dc_12v>;
>> +	};
>>  };
>>  
>>  &cpu_l0 {
>> @@ -514,6 +529,19 @@
>>  	status = "okay";
>>  };
>>  
>> +&pcie_phy {
>> +	status = "okay";
>> +};
>> +
>> +&pcie0 {
>> +	ep-gpios = <&gpio4 RK_PD1 GPIO_ACTIVE_HIGH>;
>> +	num-lanes = <4>;
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&pcie_perst>;
>> +	vpcie3v3-supply = <&vcc3v3_pcie>;
>> +	status = "okay";
>> +};
>> +
>>  &pinctrl {
>>  	lcd-panel {
>>  		lcd_panel_reset: lcd-panel-reset {
>> @@ -535,6 +563,16 @@
>>  		};
>>  	};
>>  
>> +	pcie {
>> +		vcc3v3_pcie_en: vcc3v3-pcie-en {
>> +			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
>> +		};
>> +
>> +		pcie_perst: pcie-perst {
>> +			rockchip,pins = <4 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
>> +		};
>> +	};
>> +
>>  	pmic {
>>  		vsel1_gpio: vsel1-gpio {
>>  			rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
>> 
> 
> 
> 
> 
> 
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
>
Heiko Stübner Nov. 1, 2019, 8:06 a.m. UTC | #3
Hi Markus,

Am Donnerstag, 31. Oktober 2019, 19:12:10 CET schrieb Markus Reichl:
> Am 31.10.19 um 17:57 schrieb Heiko Stuebner:
> > Am Montag, 28. Oktober 2019, 15:47:27 CET schrieb Markus Reichl:
> >> rk3399-roc-pc has a PCIe interface. Enable it for use with
> >> the M.2 NGFF M_KEY slot on roc-rk3399-mezzanine board.
> >> Tested with Samsung 970 evo plus SSD.
> >> 
> >> Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
> >> ---
> >>  .../arm64/boot/dts/rockchip/rk3399-roc-pc.dts | 38 +++++++++++++++++++
> >>  1 file changed, 38 insertions(+)
> >> 
> >> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
> >> index 9313251765c7..2d637d54994b 100644
> >> --- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
> >> +++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
> >> @@ -158,6 +158,21 @@
> >>  		regulator-max-microvolt = <1400000>;
> >>  		vin-supply = <&vcc_sys>;
> >>  	};
> >> +
> >> +	/* on roc-rk3399-mezzanine board */
> > 
> > I'm undecided on this. From what I've seen that mezzanine board is some
> > sort of addon, like a raspberry pi hat. Therefore it's not always present,
> > so probably should not be part of the base board dts.
> > 
> > I'm thinking a dt-overlay that can then be activated might be the solution
> > of choice, but I've reached out to arm-soc poeple on irc to determine the
> > correct course.
> > 
> I have seen some board.dtsi with board_only.dts respective board_extension.dts
> in the arch/arm64/boot/dts/rockchip directory. Would that be ok?

The answer is twofold I guess ;-)

(1) The 100% correct way would probably be to use a devicetree overlay
together with capemgr [0] to load the overlay from userspace, but

(2a) The distinction between system-on-module + baseboard and
board+cape is somewhat foggy I think and it really doesn't look like there
will be a big plethora of capes for the roc-rk3399-pc

(2b) People may actually want to boot of that nvme pcie drive attached
to the mezzanine, so it will be somewhat permanent connection anyway
and also the system then cannot wait for userspace to come up first, if
the userspace is sitting on that drive ;-) .

So I think, going the dts+dts-extension is the best way to go.

Heiko


[0] https://elinux.org/Capemgr



> >> +	vcc3v3_pcie: vcc3v3-pcie {
> >> +		compatible = "regulator-fixed";
> >> +		regulator-name = "vcc3v3_pcie";
> >> +		enable-active-high;
> >> +		gpio = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
> >> +		pinctrl-names = "default";
> >> +		pinctrl-0 = <&vcc3v3_pcie_en>;
> >> +		regulator-always-on;
> >> +		regulator-boot-on;
> >> +		regulator-min-microvolt = <3300000>;
> >> +		regulator-max-microvolt = <3300000>;
> >> +		vin-supply = <&dc_12v>;
> >> +	};
> >>  };
> >>  
> >>  &cpu_l0 {
> >> @@ -514,6 +529,19 @@
> >>  	status = "okay";
> >>  };
> >>  
> >> +&pcie_phy {
> >> +	status = "okay";
> >> +};
> >> +
> >> +&pcie0 {
> >> +	ep-gpios = <&gpio4 RK_PD1 GPIO_ACTIVE_HIGH>;
> >> +	num-lanes = <4>;
> >> +	pinctrl-names = "default";
> >> +	pinctrl-0 = <&pcie_perst>;
> >> +	vpcie3v3-supply = <&vcc3v3_pcie>;
> >> +	status = "okay";
> >> +};
> >> +
> >>  &pinctrl {
> >>  	lcd-panel {
> >>  		lcd_panel_reset: lcd-panel-reset {
> >> @@ -535,6 +563,16 @@
> >>  		};
> >>  	};
> >>  
> >> +	pcie {
> >> +		vcc3v3_pcie_en: vcc3v3-pcie-en {
> >> +			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
> >> +		};
> >> +
> >> +		pcie_perst: pcie-perst {
> >> +			rockchip,pins = <4 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
> >> +		};
> >> +	};
> >> +
> >>  	pmic {
> >>  		vsel1_gpio: vsel1-gpio {
> >>  			rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
> >> 
> > 
> > 
> > 
> > 
> > 
> > _______________________________________________
> > Linux-rockchip mailing list
> > Linux-rockchip@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-rockchip
> > 
>
Peter Geis Nov. 1, 2019, 11:47 a.m. UTC | #4
On Fri, Nov 1, 2019 at 4:06 AM Heiko Stuebner <heiko@sntech.de> wrote:
>
> Hi Markus,
>
> Am Donnerstag, 31. Oktober 2019, 19:12:10 CET schrieb Markus Reichl:
> > Am 31.10.19 um 17:57 schrieb Heiko Stuebner:
> > > Am Montag, 28. Oktober 2019, 15:47:27 CET schrieb Markus Reichl:
> > >> rk3399-roc-pc has a PCIe interface. Enable it for use with
> > >> the M.2 NGFF M_KEY slot on roc-rk3399-mezzanine board.
> > >> Tested with Samsung 970 evo plus SSD.
> > >>
> > >> Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
> > >> ---
> > >>  .../arm64/boot/dts/rockchip/rk3399-roc-pc.dts | 38 +++++++++++++++++++
> > >>  1 file changed, 38 insertions(+)
> > >>
> > >> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
> > >> index 9313251765c7..2d637d54994b 100644
> > >> --- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
> > >> +++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
> > >> @@ -158,6 +158,21 @@
> > >>            regulator-max-microvolt = <1400000>;
> > >>            vin-supply = <&vcc_sys>;
> > >>    };
> > >> +
> > >> +  /* on roc-rk3399-mezzanine board */
> > >
> > > I'm undecided on this. From what I've seen that mezzanine board is some
> > > sort of addon, like a raspberry pi hat. Therefore it's not always present,
> > > so probably should not be part of the base board dts.
> > >
> > > I'm thinking a dt-overlay that can then be activated might be the solution
> > > of choice, but I've reached out to arm-soc poeple on irc to determine the
> > > correct course.
> > >
> > I have seen some board.dtsi with board_only.dts respective board_extension.dts
> > in the arch/arm64/boot/dts/rockchip directory. Would that be ok?
>
> The answer is twofold I guess ;-)
>
> (1) The 100% correct way would probably be to use a devicetree overlay
> together with capemgr [0] to load the overlay from userspace, but

I think this also illustrates the current lack of a device-tree
overlay loading mechanism in the current upstream kernel.
I've now seen two implementations, a sysfs based one, and now capemgr.
Reading the capemgr implementation, I like this better because it
addresses both the boot and runtime applications.

>
> (2a) The distinction between system-on-module + baseboard and
> board+cape is somewhat foggy I think and it really doesn't look like there
> will be a big plethora of capes for the roc-rk3399-pc
>
> (2b) People may actually want to boot of that nvme pcie drive attached
> to the mezzanine, so it will be somewhat permanent connection anyway
> and also the system then cannot wait for userspace to come up first, if
> the userspace is sitting on that drive ;-) .
>
> So I think, going the dts+dts-extension is the best way to go.
>
> Heiko
>
>
> [0] https://elinux.org/Capemgr
>
>
>
> > >> +  vcc3v3_pcie: vcc3v3-pcie {
> > >> +          compatible = "regulator-fixed";
> > >> +          regulator-name = "vcc3v3_pcie";
> > >> +          enable-active-high;
> > >> +          gpio = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
> > >> +          pinctrl-names = "default";
> > >> +          pinctrl-0 = <&vcc3v3_pcie_en>;
> > >> +          regulator-always-on;
> > >> +          regulator-boot-on;
> > >> +          regulator-min-microvolt = <3300000>;
> > >> +          regulator-max-microvolt = <3300000>;
> > >> +          vin-supply = <&dc_12v>;
> > >> +  };
> > >>  };
> > >>
> > >>  &cpu_l0 {
> > >> @@ -514,6 +529,19 @@
> > >>    status = "okay";
> > >>  };
> > >>
> > >> +&pcie_phy {
> > >> +  status = "okay";
> > >> +};
> > >> +
> > >> +&pcie0 {
> > >> +  ep-gpios = <&gpio4 RK_PD1 GPIO_ACTIVE_HIGH>;
> > >> +  num-lanes = <4>;
> > >> +  pinctrl-names = "default";
> > >> +  pinctrl-0 = <&pcie_perst>;
> > >> +  vpcie3v3-supply = <&vcc3v3_pcie>;
> > >> +  status = "okay";
> > >> +};
> > >> +
> > >>  &pinctrl {
> > >>    lcd-panel {
> > >>            lcd_panel_reset: lcd-panel-reset {
> > >> @@ -535,6 +563,16 @@
> > >>            };
> > >>    };
> > >>
> > >> +  pcie {
> > >> +          vcc3v3_pcie_en: vcc3v3-pcie-en {
> > >> +                  rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
> > >> +          };
> > >> +
> > >> +          pcie_perst: pcie-perst {
> > >> +                  rockchip,pins = <4 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
> > >> +          };
> > >> +  };
> > >> +
> > >>    pmic {
> > >>            vsel1_gpio: vsel1-gpio {
> > >>                    rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
> > >>
> > >
> > >
> > >
> > >
> > >
> > > _______________________________________________
> > > Linux-rockchip mailing list
> > > Linux-rockchip@lists.infradead.org
> > > http://lists.infradead.org/mailman/listinfo/linux-rockchip
> > >
> >
>
>
>
>
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
index 9313251765c7..2d637d54994b 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dts
@@ -158,6 +158,21 @@ 
 		regulator-max-microvolt = <1400000>;
 		vin-supply = <&vcc_sys>;
 	};
+
+	/* on roc-rk3399-mezzanine board */
+	vcc3v3_pcie: vcc3v3-pcie {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_pcie";
+		enable-active-high;
+		gpio = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc3v3_pcie_en>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_12v>;
+	};
 };
 
 &cpu_l0 {
@@ -514,6 +529,19 @@ 
 	status = "okay";
 };
 
+&pcie_phy {
+	status = "okay";
+};
+
+&pcie0 {
+	ep-gpios = <&gpio4 RK_PD1 GPIO_ACTIVE_HIGH>;
+	num-lanes = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_perst>;
+	vpcie3v3-supply = <&vcc3v3_pcie>;
+	status = "okay";
+};
+
 &pinctrl {
 	lcd-panel {
 		lcd_panel_reset: lcd-panel-reset {
@@ -535,6 +563,16 @@ 
 		};
 	};
 
+	pcie {
+		vcc3v3_pcie_en: vcc3v3-pcie-en {
+			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		pcie_perst: pcie-perst {
+			rockchip,pins = <4 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	pmic {
 		vsel1_gpio: vsel1-gpio {
 			rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;