Message ID | 1476694990-1887-1-git-send-email-chenjh@rock-chips.com (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
Hi Jianhong, with this patch a poweroff causes a restart on our board. In our design a 5V USB voltage is supplied on the USB supply input pins. After setting DEV_OFF bit, the RK818 restart automatically. The ON_SOURCE_REG (Address AEH) is 0x40 after the automatic restart which says that the RK818 was started by ON_PLUG_IN event. Is there a possibility to configure the RK818 that it will not start automatically in this case? Regards, Wadim On 17.10.2016 11:03, Jianhong Chen wrote: > DEV_OFF and DEV_OFF_RST functions for RK808 are designed error that > only DEV_OFF_RST can power off supplies. RK818 has been fixed this > issue, so that DEV_OFF is used to power off supplies. > > Signed-off-by: Jianhong Chen <chenjh@rock-chips.com> > --- > drivers/mfd/rk808.c | 23 ++++++++++++++++++++++- > include/linux/mfd/rk808.h | 1 + > 2 files changed, 23 insertions(+), 1 deletion(-) > > diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk808.c > index 0f8acc5..2c9acdb 100644 > --- a/drivers/mfd/rk808.c > +++ b/drivers/mfd/rk808.c > @@ -290,6 +290,24 @@ static void rk808_device_shutdown(void) > dev_err(&rk808_i2c_client->dev, "power off error!\n"); > } > > +static void rk818_device_shutdown(void) > +{ > + int ret; > + struct rk808 *rk808 = i2c_get_clientdata(rk808_i2c_client); > + > + if (!rk808) { > + dev_warn(&rk808_i2c_client->dev, > + "have no rk818, so do nothing here\n"); > + return; > + } > + > + ret = regmap_update_bits(rk808->regmap, > + RK818_DEVCTRL_REG, > + DEV_OFF, DEV_OFF); > + if (ret) > + dev_err(&rk808_i2c_client->dev, "power off error!\n"); > +} > + > static const struct of_device_id rk808_of_match[] = { > { .compatible = "rockchip,rk808" }, > { .compatible = "rockchip,rk818" }, > @@ -304,6 +322,7 @@ static int rk808_probe(struct i2c_client *client, > struct rk808 *rk808; > const struct rk808_reg_data *pre_init_reg; > const struct mfd_cell *cells; > + void (*pm_pwroff_fn)(void); > int nr_pre_init_regs; > int nr_cells; > int pm_off = 0; > @@ -331,6 +350,7 @@ static int rk808_probe(struct i2c_client *client, > nr_pre_init_regs = ARRAY_SIZE(rk808_pre_init_reg); > cells = rk808s; > nr_cells = ARRAY_SIZE(rk808s); > + pm_pwroff_fn = rk808_device_shutdown; > break; > case RK818_ID: > rk808->regmap_cfg = &rk818_regmap_config; > @@ -339,6 +359,7 @@ static int rk808_probe(struct i2c_client *client, > nr_pre_init_regs = ARRAY_SIZE(rk818_pre_init_reg); > cells = rk818s; > nr_cells = ARRAY_SIZE(rk818s); > + pm_pwroff_fn = rk818_device_shutdown; > break; > default: > dev_err(&client->dev, "Unsupported RK8XX ID %lu\n", > @@ -393,7 +414,7 @@ static int rk808_probe(struct i2c_client *client, > "rockchip,system-power-controller"); > if (pm_off && !pm_power_off) { > rk808_i2c_client = client; > - pm_power_off = rk808_device_shutdown; > + pm_power_off = pm_pwroff_fn; > } > > return 0; > diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h > index 6d435a3..83701ef 100644 > --- a/include/linux/mfd/rk808.h > +++ b/include/linux/mfd/rk808.h > @@ -290,6 +290,7 @@ enum rk818_reg { > #define SWITCH2_EN BIT(6) > #define SWITCH1_EN BIT(5) > #define DEV_OFF_RST BIT(3) > +#define DEV_OFF BIT(0) > > #define VB_LO_ACT BIT(4) > #define VB_LO_SEL_3500MV (7 << 0)
Hi Wadim: It's impossible not to restart automatically, this situation is normal for RK818. Because it is hardware designed that RK818 can't power off when a voltage is supplies on the USB supply input pins. Best Regards 在 2016/10/21 15:44, Wadim Egorov 写道: > Hi Jianhong, > > with this patch a poweroff causes a restart on our board. > In our design a 5V USB voltage is supplied on the USB supply input pins. > After setting DEV_OFF bit, the RK818 restart automatically. The > ON_SOURCE_REG (Address AEH) is 0x40 after the automatic restart which > says that the RK818 was started by ON_PLUG_IN event. > Is there a possibility to configure the RK818 that it will not start > automatically in this case? > > Regards, > Wadim > > On 17.10.2016 11:03, Jianhong Chen wrote: >> DEV_OFF and DEV_OFF_RST functions for RK808 are designed error that >> only DEV_OFF_RST can power off supplies. RK818 has been fixed this >> issue, so that DEV_OFF is used to power off supplies. >> >> Signed-off-by: Jianhong Chen <chenjh@rock-chips.com> >> --- >> drivers/mfd/rk808.c | 23 ++++++++++++++++++++++- >> include/linux/mfd/rk808.h | 1 + >> 2 files changed, 23 insertions(+), 1 deletion(-) >> >> diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk808.c >> index 0f8acc5..2c9acdb 100644 >> --- a/drivers/mfd/rk808.c >> +++ b/drivers/mfd/rk808.c >> @@ -290,6 +290,24 @@ static void rk808_device_shutdown(void) >> dev_err(&rk808_i2c_client->dev, "power off error!\n"); >> } >> >> +static void rk818_device_shutdown(void) >> +{ >> + int ret; >> + struct rk808 *rk808 = i2c_get_clientdata(rk808_i2c_client); >> + >> + if (!rk808) { >> + dev_warn(&rk808_i2c_client->dev, >> + "have no rk818, so do nothing here\n"); >> + return; >> + } >> + >> + ret = regmap_update_bits(rk808->regmap, >> + RK818_DEVCTRL_REG, >> + DEV_OFF, DEV_OFF); >> + if (ret) >> + dev_err(&rk808_i2c_client->dev, "power off error!\n"); >> +} >> + >> static const struct of_device_id rk808_of_match[] = { >> { .compatible = "rockchip,rk808" }, >> { .compatible = "rockchip,rk818" }, >> @@ -304,6 +322,7 @@ static int rk808_probe(struct i2c_client *client, >> struct rk808 *rk808; >> const struct rk808_reg_data *pre_init_reg; >> const struct mfd_cell *cells; >> + void (*pm_pwroff_fn)(void); >> int nr_pre_init_regs; >> int nr_cells; >> int pm_off = 0; >> @@ -331,6 +350,7 @@ static int rk808_probe(struct i2c_client *client, >> nr_pre_init_regs = ARRAY_SIZE(rk808_pre_init_reg); >> cells = rk808s; >> nr_cells = ARRAY_SIZE(rk808s); >> + pm_pwroff_fn = rk808_device_shutdown; >> break; >> case RK818_ID: >> rk808->regmap_cfg = &rk818_regmap_config; >> @@ -339,6 +359,7 @@ static int rk808_probe(struct i2c_client *client, >> nr_pre_init_regs = ARRAY_SIZE(rk818_pre_init_reg); >> cells = rk818s; >> nr_cells = ARRAY_SIZE(rk818s); >> + pm_pwroff_fn = rk818_device_shutdown; >> break; >> default: >> dev_err(&client->dev, "Unsupported RK8XX ID %lu\n", >> @@ -393,7 +414,7 @@ static int rk808_probe(struct i2c_client *client, >> "rockchip,system-power-controller"); >> if (pm_off && !pm_power_off) { >> rk808_i2c_client = client; >> - pm_power_off = rk808_device_shutdown; >> + pm_power_off = pm_pwroff_fn; >> } >> >> return 0; >> diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h >> index 6d435a3..83701ef 100644 >> --- a/include/linux/mfd/rk808.h >> +++ b/include/linux/mfd/rk808.h >> @@ -290,6 +290,7 @@ enum rk818_reg { >> #define SWITCH2_EN BIT(6) >> #define SWITCH1_EN BIT(5) >> #define DEV_OFF_RST BIT(3) >> +#define DEV_OFF BIT(0) >> >> #define VB_LO_ACT BIT(4) >> #define VB_LO_SEL_3500MV (7 << 0) > > >
On Mon, 17 Oct 2016, Jianhong Chen wrote: > DEV_OFF and DEV_OFF_RST functions for RK808 are designed error that > only DEV_OFF_RST can power off supplies. RK818 has been fixed this > issue, so that DEV_OFF is used to power off supplies. > > Signed-off-by: Jianhong Chen <chenjh@rock-chips.com> > --- > drivers/mfd/rk808.c | 23 ++++++++++++++++++++++- > include/linux/mfd/rk808.h | 1 + > 2 files changed, 23 insertions(+), 1 deletion(-) Applied, thanks. > diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk808.c > index 0f8acc5..2c9acdb 100644 > --- a/drivers/mfd/rk808.c > +++ b/drivers/mfd/rk808.c > @@ -290,6 +290,24 @@ static void rk808_device_shutdown(void) > dev_err(&rk808_i2c_client->dev, "power off error!\n"); > } > > +static void rk818_device_shutdown(void) > +{ > + int ret; > + struct rk808 *rk808 = i2c_get_clientdata(rk808_i2c_client); > + > + if (!rk808) { > + dev_warn(&rk808_i2c_client->dev, > + "have no rk818, so do nothing here\n"); > + return; > + } > + > + ret = regmap_update_bits(rk808->regmap, > + RK818_DEVCTRL_REG, > + DEV_OFF, DEV_OFF); > + if (ret) > + dev_err(&rk808_i2c_client->dev, "power off error!\n"); > +} > + > static const struct of_device_id rk808_of_match[] = { > { .compatible = "rockchip,rk808" }, > { .compatible = "rockchip,rk818" }, > @@ -304,6 +322,7 @@ static int rk808_probe(struct i2c_client *client, > struct rk808 *rk808; > const struct rk808_reg_data *pre_init_reg; > const struct mfd_cell *cells; > + void (*pm_pwroff_fn)(void); > int nr_pre_init_regs; > int nr_cells; > int pm_off = 0; > @@ -331,6 +350,7 @@ static int rk808_probe(struct i2c_client *client, > nr_pre_init_regs = ARRAY_SIZE(rk808_pre_init_reg); > cells = rk808s; > nr_cells = ARRAY_SIZE(rk808s); > + pm_pwroff_fn = rk808_device_shutdown; > break; > case RK818_ID: > rk808->regmap_cfg = &rk818_regmap_config; > @@ -339,6 +359,7 @@ static int rk808_probe(struct i2c_client *client, > nr_pre_init_regs = ARRAY_SIZE(rk818_pre_init_reg); > cells = rk818s; > nr_cells = ARRAY_SIZE(rk818s); > + pm_pwroff_fn = rk818_device_shutdown; > break; > default: > dev_err(&client->dev, "Unsupported RK8XX ID %lu\n", > @@ -393,7 +414,7 @@ static int rk808_probe(struct i2c_client *client, > "rockchip,system-power-controller"); > if (pm_off && !pm_power_off) { > rk808_i2c_client = client; > - pm_power_off = rk808_device_shutdown; > + pm_power_off = pm_pwroff_fn; > } > > return 0; > diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h > index 6d435a3..83701ef 100644 > --- a/include/linux/mfd/rk808.h > +++ b/include/linux/mfd/rk808.h > @@ -290,6 +290,7 @@ enum rk818_reg { > #define SWITCH2_EN BIT(6) > #define SWITCH1_EN BIT(5) > #define DEV_OFF_RST BIT(3) > +#define DEV_OFF BIT(0) > > #define VB_LO_ACT BIT(4) > #define VB_LO_SEL_3500MV (7 << 0)
diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk808.c index 0f8acc5..2c9acdb 100644 --- a/drivers/mfd/rk808.c +++ b/drivers/mfd/rk808.c @@ -290,6 +290,24 @@ static void rk808_device_shutdown(void) dev_err(&rk808_i2c_client->dev, "power off error!\n"); } +static void rk818_device_shutdown(void) +{ + int ret; + struct rk808 *rk808 = i2c_get_clientdata(rk808_i2c_client); + + if (!rk808) { + dev_warn(&rk808_i2c_client->dev, + "have no rk818, so do nothing here\n"); + return; + } + + ret = regmap_update_bits(rk808->regmap, + RK818_DEVCTRL_REG, + DEV_OFF, DEV_OFF); + if (ret) + dev_err(&rk808_i2c_client->dev, "power off error!\n"); +} + static const struct of_device_id rk808_of_match[] = { { .compatible = "rockchip,rk808" }, { .compatible = "rockchip,rk818" }, @@ -304,6 +322,7 @@ static int rk808_probe(struct i2c_client *client, struct rk808 *rk808; const struct rk808_reg_data *pre_init_reg; const struct mfd_cell *cells; + void (*pm_pwroff_fn)(void); int nr_pre_init_regs; int nr_cells; int pm_off = 0; @@ -331,6 +350,7 @@ static int rk808_probe(struct i2c_client *client, nr_pre_init_regs = ARRAY_SIZE(rk808_pre_init_reg); cells = rk808s; nr_cells = ARRAY_SIZE(rk808s); + pm_pwroff_fn = rk808_device_shutdown; break; case RK818_ID: rk808->regmap_cfg = &rk818_regmap_config; @@ -339,6 +359,7 @@ static int rk808_probe(struct i2c_client *client, nr_pre_init_regs = ARRAY_SIZE(rk818_pre_init_reg); cells = rk818s; nr_cells = ARRAY_SIZE(rk818s); + pm_pwroff_fn = rk818_device_shutdown; break; default: dev_err(&client->dev, "Unsupported RK8XX ID %lu\n", @@ -393,7 +414,7 @@ static int rk808_probe(struct i2c_client *client, "rockchip,system-power-controller"); if (pm_off && !pm_power_off) { rk808_i2c_client = client; - pm_power_off = rk808_device_shutdown; + pm_power_off = pm_pwroff_fn; } return 0; diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h index 6d435a3..83701ef 100644 --- a/include/linux/mfd/rk808.h +++ b/include/linux/mfd/rk808.h @@ -290,6 +290,7 @@ enum rk818_reg { #define SWITCH2_EN BIT(6) #define SWITCH1_EN BIT(5) #define DEV_OFF_RST BIT(3) +#define DEV_OFF BIT(0) #define VB_LO_ACT BIT(4) #define VB_LO_SEL_3500MV (7 << 0)
DEV_OFF and DEV_OFF_RST functions for RK808 are designed error that only DEV_OFF_RST can power off supplies. RK818 has been fixed this issue, so that DEV_OFF is used to power off supplies. Signed-off-by: Jianhong Chen <chenjh@rock-chips.com> --- drivers/mfd/rk808.c | 23 ++++++++++++++++++++++- include/linux/mfd/rk808.h | 1 + 2 files changed, 23 insertions(+), 1 deletion(-)