diff mbox

[V3,2/2] ARM: dts: rockchip: add dts for RK3288-Tinker board

Message ID 1487066851-25142-3-git-send-email-eddie.cai.linux@gmail.com (mailing list archive)
State New, archived
Headers show

Commit Message

Eddie Cai Feb. 14, 2017, 10:07 a.m. UTC
This patch add basic support for RK3288-Tinker board. We can boot in to rootfs
with this patch.

Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
---
 arch/arm/boot/dts/Makefile          |   1 +
 arch/arm/boot/dts/rk3288-tinker.dts | 536 ++++++++++++++++++++++++++++++++++++
 2 files changed, 537 insertions(+)
 create mode 100644 arch/arm/boot/dts/rk3288-tinker.dts

Comments

Wadim Egorov Feb. 14, 2017, 2:12 p.m. UTC | #1
Hi Eddie,


On 14.02.2017 11:07, Eddie Cai wrote:
> This patch add basic support for RK3288-Tinker board. We can boot in to rootfs
> with this patch.
>
> Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
> ---
>  arch/arm/boot/dts/Makefile          |   1 +
>  arch/arm/boot/dts/rk3288-tinker.dts | 536 ++++++++++++++++++++++++++++++++++++
>  2 files changed, 537 insertions(+)
>  create mode 100644 arch/arm/boot/dts/rk3288-tinker.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 01d178a..0dfef24 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -679,6 +679,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
>  	rk3288-popmetal.dtb \
>  	rk3288-r89.dtb \
>  	rk3288-rock2-square.dtb \
> +	rk3288-tinker.dtb \
>  	rk3288-veyron-brain.dtb \
>  	rk3288-veyron-jaq.dtb \
>  	rk3288-veyron-jerry.dtb \
> diff --git a/arch/arm/boot/dts/rk3288-tinker.dts b/arch/arm/boot/dts/rk3288-tinker.dts
> new file mode 100644
> index 0000000..9600d1f
> --- /dev/null
> +++ b/arch/arm/boot/dts/rk3288-tinker.dts
> @@ -0,0 +1,536 @@
> +/*
> + * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "rk3288.dtsi"
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +	model = "Rockchip RK3288 Tinker Board";
> +	compatible = "asus,rk3288-tinker", "rockchip,rk3288";
> +
> +	memory {
> +		reg = <0x0 0x80000000>;
> +		device_type = "memory";
> +	};
> +
> +	ext_gmac: external-gmac-clock {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <125000000>;
> +		clock-output-names = "ext_gmac";
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		autorepeat;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pwrbtn>;
> +
> +		button@0 {
> +			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_POWER>;
> +			label = "GPIO Key Power";
> +			linux,input-type = <1>;
> +			gpio-key,wakeup = <1>;

you should replace this with wakeup-source as specified in
Documentation/devicetree/bindings/power/wakeup-source.txt

Regards,
Wadim
diff mbox

Patch

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 01d178a..0dfef24 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -679,6 +679,7 @@  dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rk3288-popmetal.dtb \
 	rk3288-r89.dtb \
 	rk3288-rock2-square.dtb \
+	rk3288-tinker.dtb \
 	rk3288-veyron-brain.dtb \
 	rk3288-veyron-jaq.dtb \
 	rk3288-veyron-jerry.dtb \
diff --git a/arch/arm/boot/dts/rk3288-tinker.dts b/arch/arm/boot/dts/rk3288-tinker.dts
new file mode 100644
index 0000000..9600d1f
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-tinker.dts
@@ -0,0 +1,536 @@ 
+/*
+ * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "rk3288.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Rockchip RK3288 Tinker Board";
+	compatible = "asus,rk3288-tinker", "rockchip,rk3288";
+
+	memory {
+		reg = <0x0 0x80000000>;
+		device_type = "memory";
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwrbtn>;
+
+		button@0 {
+			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			label = "GPIO Key Power";
+			linux,input-type = <1>;
+			gpio-key,wakeup = <1>;
+			debounce-interval = <100>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		pwr-led {
+			gpios = <&gpio0 RK_PA3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		act-led {
+			gpios=<&gpio1 RK_PD0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger="mmc0";
+		};
+
+
+		heartbeat-led {
+			gpios=<&gpio1 RK_PD1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger="heartbeat";
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,name = "rockchip,tinker-codec";
+		simple-audio-card,mclk-fs = <512>;
+		simple-audio-card,cpu {
+			sound-dai = <&i2s>;
+		};
+		simple-audio-card,codec {
+			sound-dai = <&hdmi>;
+		};
+	};
+
+	vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_sd: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc_pwr>;
+		regulator-name = "vcc_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		vin-supply = <&vcc_io>;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&gmac {
+	phy-supply = <&vcc33_lan>;
+	phy-mode = "rgmii";
+	clock_in_out = "input";
+	snps,reset-gpio = <&gpio4 7 0>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c5>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int &global_pwroff &dvs_1 &dvs_2>;
+		dvs-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
+				<&gpio0 12 GPIO_ACTIVE_HIGH>;
+
+		rockchip,system-power-controller;
+		wakeup-source;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_io>;
+		vcc9-supply = <&vcc_io>;
+		vcc10-supply = <&vcc_io>;
+		vcc11-supply = <&vcc_sys>;
+		vcc12-supply = <&vcc_io>;
+		vddio-supply = <&vcc_io>;
+
+		regulators {
+			vdd_cpu: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-name = "vdd_arm";
+				regulator-ramp-delay = <6000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-name = "vdd_gpu";
+				regulator-ramp-delay = <6000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_io";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc18_ldo1: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_ldo1";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc33_mipi: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc33_mipi";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd_10";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc18_codec: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_codec";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vdd10_lcd: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd10_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_18: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_18";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc18_lcd: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc33_sd: SWITCH_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc33_sd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc33_lan: SWITCH_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc33_lan";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	status = "okay";
+};
+
+&io_domains {
+	status = "okay";
+
+	sdcard-supply = <&vccio_sd>;
+};
+
+&pinctrl {
+	pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+		drive-strength = <8>;
+	};
+
+	pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	backlight {
+		bl_en: bl-en {
+			rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	buttons {
+		pwrbtn: pwrbtn {
+			rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	eth_phy {
+		eth_phy_pwr: eth-phy-pwr {
+			rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic-int {
+			rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO \
+					&pcfg_pull_up>;
+		};
+
+		dvs_1: dvs-1 {
+			rockchip,pins = <RK_GPIO0 11 RK_FUNC_GPIO \
+					&pcfg_pull_down>;
+		};
+
+		dvs_2: dvs-2 {
+			rockchip,pins = <RK_GPIO0 12 RK_FUNC_GPIO \
+					&pcfg_pull_down>;
+		};
+	};
+
+	sdmmc {
+		sdmmc_bus4: sdmmc-bus4 {
+			rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<6 17 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<6 18 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<6 19 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+		};
+
+		sdmmc_clk: sdmmc-clk {
+			rockchip,pins = <6 20 RK_FUNC_1 \
+					&pcfg_pull_none_drv_8ma>;
+		};
+
+		sdmmc_cmd: sdmmc-cmd {
+			rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+		};
+
+		sdmmc_pwr: sdmmc-pwr {
+			rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb {
+		host_vbus_drv: host-vbus-drv {
+			rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		pwr_3g: pwr-3g {
+			rockchip,pins = <7 8 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pwm0 {
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcc18_ldo1>;
+	status ="okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	disable-wp;			/* wp not hooked up */
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	status = "okay";
+	vmmc-supply = <&vcc33_sd>;
+	vqmmc-supply = <&vccio_sd>;
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
+	rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host1 {
+	status = "okay";
+};
+
+&usb_otg {
+	status= "okay";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};