| Message ID | 1501833976-1100-5-git-send-email-rocky.hao@rock-chips.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
在 2017年08月04日 16:06, Rocky Hao 写道: > add thermal zone and dynamic CPU power coefficients for rk3328 > > Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com> > --- > Change in v2: > - remove gerrit Change-Id > > arch/arm64/boot/dts/rockchip/rk3328.dtsi | 43 ++++++++++++++++++++++++++++++++ > 1 file changed, 43 insertions(+) > > diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi > index 186fb93fdffd..68829f808320 100644 > --- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi > +++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi > @@ -47,6 +47,7 @@ > #include <dt-bindings/pinctrl/rockchip.h> > #include <dt-bindings/power/rk3328-power.h> > #include <dt-bindings/soc/rockchip,boot-mode.h> > +#include <dt-bindings/thermal/thermal.h> > > / { > compatible = "rockchip,rk3328"; > @@ -74,6 +75,8 @@ > compatible = "arm,cortex-a53", "arm,armv8"; > reg = <0x0 0x0>; > clocks = <&cru ARMCLK>; > + #cooling-cells = <2>; /* min followed by max */ > + dynamic-power-coefficient = <120>; > enable-method = "psci"; > next-level-cache = <&l2>; > }; > @@ -83,6 +86,7 @@ > compatible = "arm,cortex-a53", "arm,armv8"; > reg = <0x0 0x1>; > clocks = <&cru ARMCLK>; > + dynamic-power-coefficient = <120>; > enable-method = "psci"; > next-level-cache = <&l2>; > }; > @@ -92,6 +96,7 @@ > compatible = "arm,cortex-a53", "arm,armv8"; > reg = <0x0 0x2>; > clocks = <&cru ARMCLK>; > + dynamic-power-coefficient = <120>; > enable-method = "psci"; > next-level-cache = <&l2>; > }; > @@ -101,6 +106,7 @@ > compatible = "arm,cortex-a53", "arm,armv8"; > reg = <0x0 0x3>; > clocks = <&cru ARMCLK>; > + dynamic-power-coefficient = <120>; > enable-method = "psci"; > next-level-cache = <&l2>; > }; > @@ -308,6 +314,43 @@ > interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; > }; > > + thermal-zones { > + soc_thermal: soc-thermal { > + polling-delay-passive = <20>; /* milliseconds */ > + polling-delay = <1000>; /* milliseconds */ > + sustainable-power = <1000>; /* milliwatts */ > + > + thermal-sensors = <&tsadc 0>; > + > + trips { > + threshold: trip-point0 { > + temperature = <70000>; /* millicelsius */ > + hysteresis = <2000>; /* millicelsius */ > + type = "passive"; > + }; > + target: trip-point1 { > + temperature = <85000>; /* millicelsius */ > + hysteresis = <2000>; /* millicelsius */ > + type = "passive"; > + }; > + soc_crit: soc-crit { > + temperature = <95000>; /* millicelsius */ > + hysteresis = <2000>; /* millicelsius */ The document had already described, maybe we should remove the millicelsius/milliseconds/milliwatts here. > + type = "critical"; > + }; > + }; > + > + cooling-maps { > + map0 { > + trip = <&target>; > + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > + contribution = <4096>; > + }; > + }; > + }; > + > + }; > + > tsadc: tsadc@ff250000 { > compatible = "rockchip,rk3328-tsadc"; > reg = <0x0 0xff250000 0x0 0x100>;
Hi Caesar, Thanks for your comments. Best Regards, Rocky 在 2017/8/11 14:44, Caesar Wang 写道: > 在 2017年08月04日 16:06, Rocky Hao 写道: >> add thermal zone and dynamic CPU power coefficients for rk3328 >> >> Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com> >> --- >> Change in v2: >> - remove gerrit Change-Id >> >> arch/arm64/boot/dts/rockchip/rk3328.dtsi | 43 >> ++++++++++++++++++++++++++++++++ >> 1 file changed, 43 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi >> b/arch/arm64/boot/dts/rockchip/rk3328.dtsi >> index 186fb93fdffd..68829f808320 100644 >> --- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi >> +++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi >> @@ -47,6 +47,7 @@ >> #include <dt-bindings/pinctrl/rockchip.h> >> #include <dt-bindings/power/rk3328-power.h> >> #include <dt-bindings/soc/rockchip,boot-mode.h> >> +#include <dt-bindings/thermal/thermal.h> >> / { >> compatible = "rockchip,rk3328"; >> @@ -74,6 +75,8 @@ >> compatible = "arm,cortex-a53", "arm,armv8"; >> reg = <0x0 0x0>; >> clocks = <&cru ARMCLK>; >> + #cooling-cells = <2>; /* min followed by max */ >> + dynamic-power-coefficient = <120>; >> enable-method = "psci"; >> next-level-cache = <&l2>; >> }; >> @@ -83,6 +86,7 @@ >> compatible = "arm,cortex-a53", "arm,armv8"; >> reg = <0x0 0x1>; >> clocks = <&cru ARMCLK>; >> + dynamic-power-coefficient = <120>; >> enable-method = "psci"; >> next-level-cache = <&l2>; >> }; >> @@ -92,6 +96,7 @@ >> compatible = "arm,cortex-a53", "arm,armv8"; >> reg = <0x0 0x2>; >> clocks = <&cru ARMCLK>; >> + dynamic-power-coefficient = <120>; >> enable-method = "psci"; >> next-level-cache = <&l2>; >> }; >> @@ -101,6 +106,7 @@ >> compatible = "arm,cortex-a53", "arm,armv8"; >> reg = <0x0 0x3>; >> clocks = <&cru ARMCLK>; >> + dynamic-power-coefficient = <120>; >> enable-method = "psci"; >> next-level-cache = <&l2>; >> }; >> @@ -308,6 +314,43 @@ >> interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; >> }; >> + thermal-zones { >> + soc_thermal: soc-thermal { >> + polling-delay-passive = <20>; /* milliseconds */ >> + polling-delay = <1000>; /* milliseconds */ >> + sustainable-power = <1000>; /* milliwatts */ >> + >> + thermal-sensors = <&tsadc 0>; >> + >> + trips { >> + threshold: trip-point0 { >> + temperature = <70000>; /* millicelsius */ >> + hysteresis = <2000>; /* millicelsius */ >> + type = "passive"; >> + }; >> + target: trip-point1 { >> + temperature = <85000>; /* millicelsius */ >> + hysteresis = <2000>; /* millicelsius */ >> + type = "passive"; >> + }; >> + soc_crit: soc-crit { >> + temperature = <95000>; /* millicelsius */ >> + hysteresis = <2000>; /* millicelsius */ > > The document had already described, maybe we should remove the > millicelsius/milliseconds/milliwatts here. It is ok for me. >> + type = "critical"; >> + }; >> + }; >> + >> + cooling-maps { >> + map0 { >> + trip = <&target>; >> + cooling-device = <&cpu0 THERMAL_NO_LIMIT >> THERMAL_NO_LIMIT>; >> + contribution = <4096>; >> + }; >> + }; >> + }; >> + >> + }; >> + >> tsadc: tsadc@ff250000 { >> compatible = "rockchip,rk3328-tsadc"; >> reg = <0x0 0xff250000 0x0 0x100>; > > > >
Hi Rocky, Am Freitag, 11. August 2017, 17:46:55 CEST schrieb rocky.hao: > Hi Caesar, > Thanks for your comments. just to add, there is no need to resend, I can drop the comments here myself when applying :-) Heiko > Best Regards, > Rocky > > 在 2017/8/11 14:44, Caesar Wang 写道: > > 在 2017年08月04日 16:06, Rocky Hao 写道: > >> add thermal zone and dynamic CPU power coefficients for rk3328 > >> > >> Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com> > >> --- > >> Change in v2: > >> - remove gerrit Change-Id > >> > >> arch/arm64/boot/dts/rockchip/rk3328.dtsi | 43 > >> ++++++++++++++++++++++++++++++++ > >> 1 file changed, 43 insertions(+) > >> > >> diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi > >> b/arch/arm64/boot/dts/rockchip/rk3328.dtsi > >> index 186fb93fdffd..68829f808320 100644 > >> --- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi > >> +++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi > >> @@ -47,6 +47,7 @@ > >> #include <dt-bindings/pinctrl/rockchip.h> > >> #include <dt-bindings/power/rk3328-power.h> > >> #include <dt-bindings/soc/rockchip,boot-mode.h> > >> +#include <dt-bindings/thermal/thermal.h> > >> / { > >> compatible = "rockchip,rk3328"; > >> @@ -74,6 +75,8 @@ > >> compatible = "arm,cortex-a53", "arm,armv8"; > >> reg = <0x0 0x0>; > >> clocks = <&cru ARMCLK>; > >> + #cooling-cells = <2>; /* min followed by max */ > >> + dynamic-power-coefficient = <120>; > >> enable-method = "psci"; > >> next-level-cache = <&l2>; > >> }; > >> @@ -83,6 +86,7 @@ > >> compatible = "arm,cortex-a53", "arm,armv8"; > >> reg = <0x0 0x1>; > >> clocks = <&cru ARMCLK>; > >> + dynamic-power-coefficient = <120>; > >> enable-method = "psci"; > >> next-level-cache = <&l2>; > >> }; > >> @@ -92,6 +96,7 @@ > >> compatible = "arm,cortex-a53", "arm,armv8"; > >> reg = <0x0 0x2>; > >> clocks = <&cru ARMCLK>; > >> + dynamic-power-coefficient = <120>; > >> enable-method = "psci"; > >> next-level-cache = <&l2>; > >> }; > >> @@ -101,6 +106,7 @@ > >> compatible = "arm,cortex-a53", "arm,armv8"; > >> reg = <0x0 0x3>; > >> clocks = <&cru ARMCLK>; > >> + dynamic-power-coefficient = <120>; > >> enable-method = "psci"; > >> next-level-cache = <&l2>; > >> }; > >> @@ -308,6 +314,43 @@ > >> interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; > >> }; > >> + thermal-zones { > >> + soc_thermal: soc-thermal { > >> + polling-delay-passive = <20>; /* milliseconds */ > >> + polling-delay = <1000>; /* milliseconds */ > >> + sustainable-power = <1000>; /* milliwatts */ > >> + > >> + thermal-sensors = <&tsadc 0>; > >> + > >> + trips { > >> + threshold: trip-point0 { > >> + temperature = <70000>; /* millicelsius */ > >> + hysteresis = <2000>; /* millicelsius */ > >> + type = "passive"; > >> + }; > >> + target: trip-point1 { > >> + temperature = <85000>; /* millicelsius */ > >> + hysteresis = <2000>; /* millicelsius */ > >> + type = "passive"; > >> + }; > >> + soc_crit: soc-crit { > >> + temperature = <95000>; /* millicelsius */ > >> + hysteresis = <2000>; /* millicelsius */ > > > > The document had already described, maybe we should remove the > > millicelsius/milliseconds/milliwatts here. > It is ok for me. > >> + type = "critical"; > >> + }; > >> + }; > >> + > >> + cooling-maps { > >> + map0 { > >> + trip = <&target>; > >> + cooling-device = <&cpu0 THERMAL_NO_LIMIT > >> THERMAL_NO_LIMIT>; > >> + contribution = <4096>; > >> + }; > >> + }; > >> + }; > >> + > >> + }; > >> + > >> tsadc: tsadc@ff250000 { > >> compatible = "rockchip,rk3328-tsadc"; > >> reg = <0x0 0xff250000 0x0 0x100>; > > > > > > > > > > >
Am Freitag, 4. August 2017, 16:06:15 CEST schrieb Rocky Hao: > add thermal zone and dynamic CPU power coefficients for rk3328 > > Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com> applied for 4.14 after dropping the unnecessary property-comments. Thanks Heiko
diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi index 186fb93fdffd..68829f808320 100644 --- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi @@ -47,6 +47,7 @@ #include <dt-bindings/pinctrl/rockchip.h> #include <dt-bindings/power/rk3328-power.h> #include <dt-bindings/soc/rockchip,boot-mode.h> +#include <dt-bindings/thermal/thermal.h> / { compatible = "rockchip,rk3328"; @@ -74,6 +75,8 @@ compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x0 0x0>; clocks = <&cru ARMCLK>; + #cooling-cells = <2>; /* min followed by max */ + dynamic-power-coefficient = <120>; enable-method = "psci"; next-level-cache = <&l2>; }; @@ -83,6 +86,7 @@ compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x0 0x1>; clocks = <&cru ARMCLK>; + dynamic-power-coefficient = <120>; enable-method = "psci"; next-level-cache = <&l2>; }; @@ -92,6 +96,7 @@ compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x0 0x2>; clocks = <&cru ARMCLK>; + dynamic-power-coefficient = <120>; enable-method = "psci"; next-level-cache = <&l2>; }; @@ -101,6 +106,7 @@ compatible = "arm,cortex-a53", "arm,armv8"; reg = <0x0 0x3>; clocks = <&cru ARMCLK>; + dynamic-power-coefficient = <120>; enable-method = "psci"; next-level-cache = <&l2>; }; @@ -308,6 +314,43 @@ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; }; + thermal-zones { + soc_thermal: soc-thermal { + polling-delay-passive = <20>; /* milliseconds */ + polling-delay = <1000>; /* milliseconds */ + sustainable-power = <1000>; /* milliwatts */ + + thermal-sensors = <&tsadc 0>; + + trips { + threshold: trip-point0 { + temperature = <70000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + target: trip-point1 { + temperature = <85000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + soc_crit: soc-crit { + temperature = <95000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&target>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + contribution = <4096>; + }; + }; + }; + + }; + tsadc: tsadc@ff250000 { compatible = "rockchip,rk3328-tsadc"; reg = <0x0 0xff250000 0x0 0x100>;
add thermal zone and dynamic CPU power coefficients for rk3328 Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com> --- Change in v2: - remove gerrit Change-Id arch/arm64/boot/dts/rockchip/rk3328.dtsi | 43 ++++++++++++++++++++++++++++++++ 1 file changed, 43 insertions(+)