diff mbox series

[4/4] dt-bindings: phy-rockchip-inno-usb2: add new rockchip, force-bvalid property.

Message ID 20180815095934.11205-5-enric.balletbo@collabora.com (mailing list archive)
State New, archived
Headers show
Series phy: rockchip-inno-usb2: document improvements and allow to force B-device valid session bit. | expand

Commit Message

Enric Balletbo i Serra Aug. 15, 2018, 9:59 a.m. UTC
This property is used when the otg-id pin is not connected. When this
property is set it forces to set the B-Device Session Valid bit when the
port works as device and clears that bit when the port works as host.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 .../devicetree/bindings/phy/phy-rockchip-inno-usb2.txt       | 5 +++++
 1 file changed, 5 insertions(+)

Comments

Heiko Stübner Aug. 15, 2018, 10:34 a.m. UTC | #1
Am Mittwoch, 15. August 2018, 11:59:34 CEST schrieb Enric Balletbo i Serra:
> This property is used when the otg-id pin is not connected. When this
> property is set it forces to set the B-Device Session Valid bit when the
> port works as device and clears that bit when the port works as host.
> 
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> ---
> 
>  .../devicetree/bindings/phy/phy-rockchip-inno-usb2.txt       | 5 +++++
>  1 file changed, 5 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> index 2d4808d3920b..55761f466c41 100644
> --- a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> @@ -48,6 +48,11 @@ Optional properties:
>  		See ./phy-bindings.txt for details.
>   - rockchip,utmi-avalid : boolean, use the avalid register to get vbus status.
>  			  Otherwise, use the bvalid register.
> + - rockchip,force-bvalid : boolean, set this to force the B-Device Session
> +			  Valid bit when the usb port is in device mode. This
> +			  is used when the otg-id pin is not connected.
> +			  Only supported in case of compatible being:
> +			  * "rockchip,rk3399-usb2phy"

I guess you could drop that rk3399 mention instead make the
driver complain? Trying to keep that list up to date will get hard
and I guess the other socs may very well hide that setting somewhere
in their undocumented phy registers as well.

I guess a bit of alphabetical ordering might also be nice,
rockchip,force-bvalid above rockchip,utmi-avalid
Makes it easier to read ;-)

Heiko
Rob Herring (Arm) Aug. 15, 2018, 10:26 p.m. UTC | #2
On Wed, Aug 15, 2018 at 11:59:34AM +0200, Enric Balletbo i Serra wrote:
> This property is used when the otg-id pin is not connected. When this
> property is set it forces to set the B-Device Session Valid bit when the
> port works as device and clears that bit when the port works as host.
> 
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> ---
> 
>  .../devicetree/bindings/phy/phy-rockchip-inno-usb2.txt       | 5 +++++
>  1 file changed, 5 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> index 2d4808d3920b..55761f466c41 100644
> --- a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> @@ -48,6 +48,11 @@ Optional properties:
>  		See ./phy-bindings.txt for details.
>   - rockchip,utmi-avalid : boolean, use the avalid register to get vbus status.
>  			  Otherwise, use the bvalid register.
> + - rockchip,force-bvalid : boolean, set this to force the B-Device Session
> +			  Valid bit when the usb port is in device mode. This
> +			  is used when the otg-id pin is not connected.
> +			  Only supported in case of compatible being:
> +			  * "rockchip,rk3399-usb2phy"

Shouldn't you describe the property of the h/w that ID pin is not 
connected, rather than what you do with that information.

Is the pin not connected because it's a connector without ID pin? If so, 
that should be a property of the connector (or inferred from the 
connector compatible string).

Rob
Enric Balletbo Serra Jan. 10, 2019, 9:06 a.m. UTC | #3
Hi Rob,

Missatge de Rob Herring <robh@kernel.org> del dia dj., 16 d’ag. 2018 a les 0:26:
>
> On Wed, Aug 15, 2018 at 11:59:34AM +0200, Enric Balletbo i Serra wrote:
> > This property is used when the otg-id pin is not connected. When this
> > property is set it forces to set the B-Device Session Valid bit when the
> > port works as device and clears that bit when the port works as host.
> >
> > Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> > ---
> >
> >  .../devicetree/bindings/phy/phy-rockchip-inno-usb2.txt       | 5 +++++
> >  1 file changed, 5 insertions(+)
> >
> > diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> > index 2d4808d3920b..55761f466c41 100644
> > --- a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> > +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> > @@ -48,6 +48,11 @@ Optional properties:
> >               See ./phy-bindings.txt for details.
> >   - rockchip,utmi-avalid : boolean, use the avalid register to get vbus status.
> >                         Otherwise, use the bvalid register.
> > + - rockchip,force-bvalid : boolean, set this to force the B-Device Session
> > +                       Valid bit when the usb port is in device mode. This
> > +                       is used when the otg-id pin is not connected.
> > +                       Only supported in case of compatible being:
> > +                       * "rockchip,rk3399-usb2phy"
>
> Shouldn't you describe the property of the h/w that ID pin is not
> connected, rather than what you do with that information.
>

What about "rockchip, otg-id-not-connected"?

> Is the pin not connected because it's a connector without ID pin? If so,
> that should be a property of the connector (or inferred from the
> connector compatible string).
>

No, it's not the connector. it is not wired on the phy and the cable
detection is done via an extcon.

Thanks,
 Enric

> Rob
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
Heiko Stübner Jan. 10, 2019, 12:31 p.m. UTC | #4
Hi Enric,
Am Donnerstag, 10. Januar 2019, 10:06:38 CET schrieb Enric Balletbo Serra:
> Missatge de Rob Herring <robh@kernel.org> del dia dj., 16 d’ag. 2018 a les 0:26:
> >
> > On Wed, Aug 15, 2018 at 11:59:34AM +0200, Enric Balletbo i Serra wrote:
> > > This property is used when the otg-id pin is not connected. When this
> > > property is set it forces to set the B-Device Session Valid bit when the
> > > port works as device and clears that bit when the port works as host.
> > >
> > > Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> > > ---
> > >
> > >  .../devicetree/bindings/phy/phy-rockchip-inno-usb2.txt       | 5 +++++
> > >  1 file changed, 5 insertions(+)
> > >
> > > diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> > > index 2d4808d3920b..55761f466c41 100644
> > > --- a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> > > +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> > > @@ -48,6 +48,11 @@ Optional properties:
> > >               See ./phy-bindings.txt for details.
> > >   - rockchip,utmi-avalid : boolean, use the avalid register to get vbus status.
> > >                         Otherwise, use the bvalid register.
> > > + - rockchip,force-bvalid : boolean, set this to force the B-Device Session
> > > +                       Valid bit when the usb port is in device mode. This
> > > +                       is used when the otg-id pin is not connected.
> > > +                       Only supported in case of compatible being:
> > > +                       * "rockchip,rk3399-usb2phy"
> >
> > Shouldn't you describe the property of the h/w that ID pin is not
> > connected, rather than what you do with that information.
> >
> 
> What about "rockchip, otg-id-not-connected"?

just pointing back to our discussion in patch3 about simply assuming
id-not-connected in the case of the extcon missing

I still think that might be the cleaner variant? But I guess you're
probably already looking into doing that as so far you only resend the
cleanup patches :-) .


Heiko
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
index 2d4808d3920b..55761f466c41 100644
--- a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
@@ -48,6 +48,11 @@  Optional properties:
 		See ./phy-bindings.txt for details.
  - rockchip,utmi-avalid : boolean, use the avalid register to get vbus status.
 			  Otherwise, use the bvalid register.
+ - rockchip,force-bvalid : boolean, set this to force the B-Device Session
+			  Valid bit when the usb port is in device mode. This
+			  is used when the otg-id pin is not connected.
+			  Only supported in case of compatible being:
+			  * "rockchip,rk3399-usb2phy"
 
 Example: