diff mbox series

[net-next,3/3] net: stmmac: Add RK3566/RK3568 SoC support

Message ID 20210413210235.489467-4-ezequiel@collabora.com (mailing list archive)
State New, archived
Headers show
Series net: stmmac: RK3566/RK3568 | expand

Commit Message

Ezequiel Garcia April 13, 2021, 9:02 p.m. UTC
From: David Wu <david.wu@rock-chips.com>

Add constants and callback functions for the dwmac present
on RK3566 and RK3568 SoCs. As can be seen, the base structure
is the same, only registers and the bits in them moved slightly.

RK3568 supports two MACs, and RK3566 support just one.

Signed-off-by: David Wu <david.wu@rock-chips.com>
[Ezequiel: Add rockchip,rk3566-gmac compatible string]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
---
 .../bindings/net/rockchip-dwmac.txt           |   2 +
 .../net/ethernet/stmicro/stmmac/dwmac-rk.c    | 142 ++++++++++++++++++
 2 files changed, 144 insertions(+)

Comments

Peter Geis April 13, 2021, 10:51 p.m. UTC | #1
On Tue, Apr 13, 2021 at 5:03 PM Ezequiel Garcia <ezequiel@collabora.com> wrote:
>
> From: David Wu <david.wu@rock-chips.com>
>
> Add constants and callback functions for the dwmac present
> on RK3566 and RK3568 SoCs. As can be seen, the base structure
> is the same, only registers and the bits in them moved slightly.
>
> RK3568 supports two MACs, and RK3566 support just one.

Tested this driver on the rk3566-quartz64.
It fails to fully probe the gmac with the following error:
[    5.711127] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found
[    5.714147] rk_gmac-dwmac fe010000.ethernet: no regulator found
[    5.714766] rk_gmac-dwmac fe010000.ethernet: clock input or output? (input).
[    5.715474] rk_gmac-dwmac fe010000.ethernet: TX delay(0x4f).
[    5.716058] rk_gmac-dwmac fe010000.ethernet: RX delay(0x25).
[    5.716694] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
[    5.718413] rk_gmac-dwmac fe010000.ethernet: clock input from PHY
[    5.724140] rk_gmac-dwmac fe010000.ethernet: init for RGMII
[    5.726802] rk_gmac-dwmac fe010000.ethernet: Version ID not available
[    5.727525] rk_gmac-dwmac fe010000.ethernet:         DWMAC1000
[    5.728064] rk_gmac-dwmac fe010000.ethernet: DMA HW capability
register supported
[    5.729026] rk_gmac-dwmac fe010000.ethernet: Normal descriptors
[    5.729624] rk_gmac-dwmac fe010000.ethernet: Ring mode enabled
[    5.731123] rk_gmac-dwmac fe010000.ethernet: Unbalanced pm_runtime_enable!
[    5.873329] libphy: stmmac: probed
[    5.905599] rk_gmac-dwmac fe010000.ethernet: Cannot register the MDIO bus
[    5.906335] rk_gmac-dwmac fe010000.ethernet: stmmac_dvr_probe: MDIO
bus (id: 1) registration failed
[    5.914338] rk_gmac-dwmac: probe of fe010000.ethernet failed with error -5

This is due to the lack of setting has_gmac4 = true.

>
> Signed-off-by: David Wu <david.wu@rock-chips.com>
> [Ezequiel: Add rockchip,rk3566-gmac compatible string]
> Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
> ---
>  .../bindings/net/rockchip-dwmac.txt           |   2 +
>  .../net/ethernet/stmicro/stmmac/dwmac-rk.c    | 142 ++++++++++++++++++
>  2 files changed, 144 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
> index 3b71da7e8742..80203b16b652 100644
> --- a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
> +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
> @@ -12,6 +12,8 @@ Required properties:
>     "rockchip,rk3366-gmac": found on RK3366 SoCs
>     "rockchip,rk3368-gmac": found on RK3368 SoCs
>     "rockchip,rk3399-gmac": found on RK3399 SoCs
> +   "rockchip,rk3566-gmac": found on RK3566 SoCs
> +   "rockchip,rk3568-gmac": found on RK3568 SoCs
>     "rockchip,rv1108-gmac": found on RV1108 SoCs
>   - reg: addresses and length of the register sets for the device.
>   - interrupts: Should contain the GMAC interrupts.
> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
> index d2637d83899e..096965b0fec9 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
> @@ -948,6 +948,146 @@ static const struct rk_gmac_ops rk3399_ops = {
>         .set_rmii_speed = rk3399_set_rmii_speed,
>  };
>
> +#define RK3568_GRF_GMAC0_CON0          0x0380
> +#define RK3568_GRF_GMAC0_CON1          0x0384
> +#define RK3568_GRF_GMAC1_CON0          0x0388
> +#define RK3568_GRF_GMAC1_CON1          0x038c
> +
> +/* RK3568_GRF_GMAC0_CON1 && RK3568_GRF_GMAC1_CON1 */
> +#define RK3568_GMAC_PHY_INTF_SEL_RGMII \
> +               (GRF_BIT(4) | GRF_CLR_BIT(5) | GRF_CLR_BIT(6))
> +#define RK3568_GMAC_PHY_INTF_SEL_RMII  \
> +               (GRF_CLR_BIT(4) | GRF_CLR_BIT(5) | GRF_BIT(6))
> +#define RK3568_GMAC_FLOW_CTRL                  GRF_BIT(3)
> +#define RK3568_GMAC_FLOW_CTRL_CLR              GRF_CLR_BIT(3)
> +#define RK3568_GMAC_RXCLK_DLY_ENABLE           GRF_BIT(1)
> +#define RK3568_GMAC_RXCLK_DLY_DISABLE          GRF_CLR_BIT(1)
> +#define RK3568_GMAC_TXCLK_DLY_ENABLE           GRF_BIT(0)
> +#define RK3568_GMAC_TXCLK_DLY_DISABLE          GRF_CLR_BIT(0)
> +
> +/* RK3568_GRF_GMAC0_CON0 && RK3568_GRF_GMAC1_CON0 */
> +#define RK3568_GMAC_CLK_RX_DL_CFG(val) HIWORD_UPDATE(val, 0x7F, 8)
> +#define RK3568_GMAC_CLK_TX_DL_CFG(val) HIWORD_UPDATE(val, 0x7F, 0)
> +
> +static void rk3566_set_to_rgmii(struct rk_priv_data *bsp_priv,
> +                               int tx_delay, int rx_delay)
> +{
> +       struct device *dev = &bsp_priv->pdev->dev;
> +
> +       if (IS_ERR(bsp_priv->grf)) {
> +               dev_err(dev, "Missing rockchip,grf property\n");
> +               return;
> +       }
> +
> +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> +
> +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON0,
> +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> +}
> +
> +static void rk3566_set_to_rmii(struct rk_priv_data *bsp_priv)
> +{
> +       struct device *dev = &bsp_priv->pdev->dev;
> +
> +       if (IS_ERR(bsp_priv->grf)) {
> +               dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
> +               return;
> +       }
> +
> +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> +                    RK3568_GMAC_PHY_INTF_SEL_RMII);
> +}
> +
> +static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
> +                               int tx_delay, int rx_delay)
> +{
> +       struct device *dev = &bsp_priv->pdev->dev;
> +
> +       if (IS_ERR(bsp_priv->grf)) {
> +               dev_err(dev, "Missing rockchip,grf property\n");
> +               return;
> +       }
> +
> +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON1,
> +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> +
> +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON0,
> +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> +
> +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> +
> +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON0,
> +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));

Since there are two GMACs on the rk3568, and either, or, or both may
be enabled in various configurations, we should only configure the
controller we are currently operating.

> +}
> +
> +static void rk3568_set_to_rmii(struct rk_priv_data *bsp_priv)
> +{
> +       struct device *dev = &bsp_priv->pdev->dev;
> +
> +       if (IS_ERR(bsp_priv->grf)) {
> +               dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
> +               return;
> +       }
> +
> +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON1,
> +                    RK3568_GMAC_PHY_INTF_SEL_RMII);
> +
> +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> +                    RK3568_GMAC_PHY_INTF_SEL_RMII);

Same as above.

> +}
> +
> +static void rk3568_set_gmac_speed(struct rk_priv_data *bsp_priv, int speed)
> +{
> +       struct device *dev = &bsp_priv->pdev->dev;
> +       unsigned long rate;
> +       int ret;
> +
> +       switch (speed) {
> +       case 10:
> +               rate = 2500000;
> +               break;
> +       case 100:
> +               rate = 25000000;
> +               break;
> +       case 1000:
> +               rate = 125000000;
> +               break;
> +       default:
> +               dev_err(dev, "unknown speed value for GMAC speed=%d", speed);
> +               return;
> +       }
> +
> +       ret = clk_set_rate(bsp_priv->clk_mac_speed, rate);
> +       if (ret)
> +               dev_err(dev, "%s: set clk_mac_speed rate %ld failed %d\n",
> +                       __func__, rate, ret);
> +}
> +
> +static const struct rk_gmac_ops rk3568_ops = {
> +       .set_to_rgmii = rk3568_set_to_rgmii,
> +       .set_to_rmii = rk3568_set_to_rmii,
> +       .set_rgmii_speed = rk3568_set_gmac_speed,
> +       .set_rmii_speed = rk3568_set_gmac_speed,
> +};
> +
> +static const struct rk_gmac_ops rk3566_ops = {
> +       .set_to_rgmii = rk3566_set_to_rgmii,
> +       .set_to_rmii = rk3566_set_to_rmii,
> +       .set_rgmii_speed = rk3568_set_gmac_speed,
> +       .set_rmii_speed = rk3568_set_gmac_speed,
> +};
> +
>  #define RV1108_GRF_GMAC_CON0           0X0900
>
>  /* RV1108_GRF_GMAC_CON0 */
> @@ -1512,6 +1652,8 @@ static const struct of_device_id rk_gmac_dwmac_match[] = {
>         { .compatible = "rockchip,rk3366-gmac", .data = &rk3366_ops },
>         { .compatible = "rockchip,rk3368-gmac", .data = &rk3368_ops },
>         { .compatible = "rockchip,rk3399-gmac", .data = &rk3399_ops },
> +       { .compatible = "rockchip,rk3568-gmac", .data = &rk3568_ops },
> +       { .compatible = "rockchip,rk3566-gmac", .data = &rk3566_ops },
>         { .compatible = "rockchip,rv1108-gmac", .data = &rv1108_ops },
>         { }
>  };
> --
> 2.30.0
>
Ezequiel Garcia April 13, 2021, 11:37 p.m. UTC | #2
On Tuesday, April 13, 2021 19:51 -03, Peter Geis <pgwipeout@gmail.com> wrote: 
 
> On Tue, Apr 13, 2021 at 5:03 PM Ezequiel Garcia <ezequiel@collabora.com> wrote:
> >
> > From: David Wu <david.wu@rock-chips.com>
> >
> > Add constants and callback functions for the dwmac present
> > on RK3566 and RK3568 SoCs. As can be seen, the base structure
> > is the same, only registers and the bits in them moved slightly.
> >
> > RK3568 supports two MACs, and RK3566 support just one.
> 
> Tested this driver on the rk3566-quartz64.
> It fails to fully probe the gmac with the following error:
> [    5.711127] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found
> [    5.714147] rk_gmac-dwmac fe010000.ethernet: no regulator found
> [    5.714766] rk_gmac-dwmac fe010000.ethernet: clock input or output? (input).
> [    5.715474] rk_gmac-dwmac fe010000.ethernet: TX delay(0x4f).
> [    5.716058] rk_gmac-dwmac fe010000.ethernet: RX delay(0x25).
> [    5.716694] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
> [    5.718413] rk_gmac-dwmac fe010000.ethernet: clock input from PHY
> [    5.724140] rk_gmac-dwmac fe010000.ethernet: init for RGMII
> [    5.726802] rk_gmac-dwmac fe010000.ethernet: Version ID not available
> [    5.727525] rk_gmac-dwmac fe010000.ethernet:         DWMAC1000
> [    5.728064] rk_gmac-dwmac fe010000.ethernet: DMA HW capability
> register supported
> [    5.729026] rk_gmac-dwmac fe010000.ethernet: Normal descriptors
> [    5.729624] rk_gmac-dwmac fe010000.ethernet: Ring mode enabled
> [    5.731123] rk_gmac-dwmac fe010000.ethernet: Unbalanced pm_runtime_enable!
> [    5.873329] libphy: stmmac: probed
> [    5.905599] rk_gmac-dwmac fe010000.ethernet: Cannot register the MDIO bus
> [    5.906335] rk_gmac-dwmac fe010000.ethernet: stmmac_dvr_probe: MDIO
> bus (id: 1) registration failed
> [    5.914338] rk_gmac-dwmac: probe of fe010000.ethernet failed with error -5
> 
> This is due to the lack of setting has_gmac4 = true.
> 

You are probably missing a "snps,dwmac-4.20a" in your compatible string, i.e.:
  compatible = "rockchip,rk3566-gmac", "snps,dwmac-4.20a";

This seems to be common practice, judging from arch/arm/boot/dts/stm32***.

Let me know how that goes!
Ezequiel

> >
> > Signed-off-by: David Wu <david.wu@rock-chips.com>
> > [Ezequiel: Add rockchip,rk3566-gmac compatible string]
> > Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
> > ---
> >  .../bindings/net/rockchip-dwmac.txt           |   2 +
> >  .../net/ethernet/stmicro/stmmac/dwmac-rk.c    | 142 ++++++++++++++++++
> >  2 files changed, 144 insertions(+)
> >
> > diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
> > index 3b71da7e8742..80203b16b652 100644
> > --- a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
> > +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
> > @@ -12,6 +12,8 @@ Required properties:
> >     "rockchip,rk3366-gmac": found on RK3366 SoCs
> >     "rockchip,rk3368-gmac": found on RK3368 SoCs
> >     "rockchip,rk3399-gmac": found on RK3399 SoCs
> > +   "rockchip,rk3566-gmac": found on RK3566 SoCs
> > +   "rockchip,rk3568-gmac": found on RK3568 SoCs
> >     "rockchip,rv1108-gmac": found on RV1108 SoCs
> >   - reg: addresses and length of the register sets for the device.
> >   - interrupts: Should contain the GMAC interrupts.
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
> > index d2637d83899e..096965b0fec9 100644
> > --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
> > +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
> > @@ -948,6 +948,146 @@ static const struct rk_gmac_ops rk3399_ops = {
> >         .set_rmii_speed = rk3399_set_rmii_speed,
> >  };
> >
> > +#define RK3568_GRF_GMAC0_CON0          0x0380
> > +#define RK3568_GRF_GMAC0_CON1          0x0384
> > +#define RK3568_GRF_GMAC1_CON0          0x0388
> > +#define RK3568_GRF_GMAC1_CON1          0x038c
> > +
> > +/* RK3568_GRF_GMAC0_CON1 && RK3568_GRF_GMAC1_CON1 */
> > +#define RK3568_GMAC_PHY_INTF_SEL_RGMII \
> > +               (GRF_BIT(4) | GRF_CLR_BIT(5) | GRF_CLR_BIT(6))
> > +#define RK3568_GMAC_PHY_INTF_SEL_RMII  \
> > +               (GRF_CLR_BIT(4) | GRF_CLR_BIT(5) | GRF_BIT(6))
> > +#define RK3568_GMAC_FLOW_CTRL                  GRF_BIT(3)
> > +#define RK3568_GMAC_FLOW_CTRL_CLR              GRF_CLR_BIT(3)
> > +#define RK3568_GMAC_RXCLK_DLY_ENABLE           GRF_BIT(1)
> > +#define RK3568_GMAC_RXCLK_DLY_DISABLE          GRF_CLR_BIT(1)
> > +#define RK3568_GMAC_TXCLK_DLY_ENABLE           GRF_BIT(0)
> > +#define RK3568_GMAC_TXCLK_DLY_DISABLE          GRF_CLR_BIT(0)
> > +
> > +/* RK3568_GRF_GMAC0_CON0 && RK3568_GRF_GMAC1_CON0 */
> > +#define RK3568_GMAC_CLK_RX_DL_CFG(val) HIWORD_UPDATE(val, 0x7F, 8)
> > +#define RK3568_GMAC_CLK_TX_DL_CFG(val) HIWORD_UPDATE(val, 0x7F, 0)
> > +
> > +static void rk3566_set_to_rgmii(struct rk_priv_data *bsp_priv,
> > +                               int tx_delay, int rx_delay)
> > +{
> > +       struct device *dev = &bsp_priv->pdev->dev;
> > +
> > +       if (IS_ERR(bsp_priv->grf)) {
> > +               dev_err(dev, "Missing rockchip,grf property\n");
> > +               return;
> > +       }
> > +
> > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > +
> > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON0,
> > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> > +}
> > +
> > +static void rk3566_set_to_rmii(struct rk_priv_data *bsp_priv)
> > +{
> > +       struct device *dev = &bsp_priv->pdev->dev;
> > +
> > +       if (IS_ERR(bsp_priv->grf)) {
> > +               dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
> > +               return;
> > +       }
> > +
> > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > +                    RK3568_GMAC_PHY_INTF_SEL_RMII);
> > +}
> > +
> > +static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
> > +                               int tx_delay, int rx_delay)
> > +{
> > +       struct device *dev = &bsp_priv->pdev->dev;
> > +
> > +       if (IS_ERR(bsp_priv->grf)) {
> > +               dev_err(dev, "Missing rockchip,grf property\n");
> > +               return;
> > +       }
> > +
> > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON1,
> > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > +
> > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON0,
> > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> > +
> > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > +
> > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON0,
> > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> 
> Since there are two GMACs on the rk3568, and either, or, or both may
> be enabled in various configurations, we should only configure the
> controller we are currently operating.
> 
> > +}
> > +
> > +static void rk3568_set_to_rmii(struct rk_priv_data *bsp_priv)
> > +{
> > +       struct device *dev = &bsp_priv->pdev->dev;
> > +
> > +       if (IS_ERR(bsp_priv->grf)) {
> > +               dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
> > +               return;
> > +       }
> > +
> > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON1,
> > +                    RK3568_GMAC_PHY_INTF_SEL_RMII);
> > +
> > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > +                    RK3568_GMAC_PHY_INTF_SEL_RMII);
> 
> Same as above.
> 
> > +}
> > +
> > +static void rk3568_set_gmac_speed(struct rk_priv_data *bsp_priv, int speed)
> > +{
> > +       struct device *dev = &bsp_priv->pdev->dev;
> > +       unsigned long rate;
> > +       int ret;
> > +
> > +       switch (speed) {
> > +       case 10:
> > +               rate = 2500000;
> > +               break;
> > +       case 100:
> > +               rate = 25000000;
> > +               break;
> > +       case 1000:
> > +               rate = 125000000;
> > +               break;
> > +       default:
> > +               dev_err(dev, "unknown speed value for GMAC speed=%d", speed);
> > +               return;
> > +       }
> > +
> > +       ret = clk_set_rate(bsp_priv->clk_mac_speed, rate);
> > +       if (ret)
> > +               dev_err(dev, "%s: set clk_mac_speed rate %ld failed %d\n",
> > +                       __func__, rate, ret);
> > +}
> > +
> > +static const struct rk_gmac_ops rk3568_ops = {
> > +       .set_to_rgmii = rk3568_set_to_rgmii,
> > +       .set_to_rmii = rk3568_set_to_rmii,
> > +       .set_rgmii_speed = rk3568_set_gmac_speed,
> > +       .set_rmii_speed = rk3568_set_gmac_speed,
> > +};
> > +
> > +static const struct rk_gmac_ops rk3566_ops = {
> > +       .set_to_rgmii = rk3566_set_to_rgmii,
> > +       .set_to_rmii = rk3566_set_to_rmii,
> > +       .set_rgmii_speed = rk3568_set_gmac_speed,
> > +       .set_rmii_speed = rk3568_set_gmac_speed,
> > +};
> > +
> >  #define RV1108_GRF_GMAC_CON0           0X0900
> >
> >  /* RV1108_GRF_GMAC_CON0 */
> > @@ -1512,6 +1652,8 @@ static const struct of_device_id rk_gmac_dwmac_match[] = {
> >         { .compatible = "rockchip,rk3366-gmac", .data = &rk3366_ops },
> >         { .compatible = "rockchip,rk3368-gmac", .data = &rk3368_ops },
> >         { .compatible = "rockchip,rk3399-gmac", .data = &rk3399_ops },
> > +       { .compatible = "rockchip,rk3568-gmac", .data = &rk3568_ops },
> > +       { .compatible = "rockchip,rk3566-gmac", .data = &rk3566_ops },
> >         { .compatible = "rockchip,rv1108-gmac", .data = &rv1108_ops },
> >         { }
> >  };
> > --
> > 2.30.0
> >
Peter Geis April 14, 2021, 11:03 a.m. UTC | #3
On Tue, Apr 13, 2021 at 7:37 PM Ezequiel Garcia <ezequiel@collabora.com> wrote:
>
> On Tuesday, April 13, 2021 19:51 -03, Peter Geis <pgwipeout@gmail.com> wrote:
>
> > On Tue, Apr 13, 2021 at 5:03 PM Ezequiel Garcia <ezequiel@collabora.com> wrote:
> > >
> > > From: David Wu <david.wu@rock-chips.com>
> > >
> > > Add constants and callback functions for the dwmac present
> > > on RK3566 and RK3568 SoCs. As can be seen, the base structure
> > > is the same, only registers and the bits in them moved slightly.
> > >
> > > RK3568 supports two MACs, and RK3566 support just one.
> >
> > Tested this driver on the rk3566-quartz64.
> > It fails to fully probe the gmac with the following error:
> > [    5.711127] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found
> > [    5.714147] rk_gmac-dwmac fe010000.ethernet: no regulator found
> > [    5.714766] rk_gmac-dwmac fe010000.ethernet: clock input or output? (input).
> > [    5.715474] rk_gmac-dwmac fe010000.ethernet: TX delay(0x4f).
> > [    5.716058] rk_gmac-dwmac fe010000.ethernet: RX delay(0x25).
> > [    5.716694] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
> > [    5.718413] rk_gmac-dwmac fe010000.ethernet: clock input from PHY
> > [    5.724140] rk_gmac-dwmac fe010000.ethernet: init for RGMII
> > [    5.726802] rk_gmac-dwmac fe010000.ethernet: Version ID not available
> > [    5.727525] rk_gmac-dwmac fe010000.ethernet:         DWMAC1000
> > [    5.728064] rk_gmac-dwmac fe010000.ethernet: DMA HW capability
> > register supported
> > [    5.729026] rk_gmac-dwmac fe010000.ethernet: Normal descriptors
> > [    5.729624] rk_gmac-dwmac fe010000.ethernet: Ring mode enabled
> > [    5.731123] rk_gmac-dwmac fe010000.ethernet: Unbalanced pm_runtime_enable!
> > [    5.873329] libphy: stmmac: probed
> > [    5.905599] rk_gmac-dwmac fe010000.ethernet: Cannot register the MDIO bus
> > [    5.906335] rk_gmac-dwmac fe010000.ethernet: stmmac_dvr_probe: MDIO
> > bus (id: 1) registration failed
> > [    5.914338] rk_gmac-dwmac: probe of fe010000.ethernet failed with error -5
> >
> > This is due to the lack of setting has_gmac4 = true.
> >
>
> You are probably missing a "snps,dwmac-4.20a" in your compatible string, i.e.:
>   compatible = "rockchip,rk3566-gmac", "snps,dwmac-4.20a";

Ah yes, I had disabled that because my variant took a different path.
Thanks!

>
> This seems to be common practice, judging from arch/arm/boot/dts/stm32***.
>
> Let me know how that goes!
> Ezequiel
>
> > >
> > > Signed-off-by: David Wu <david.wu@rock-chips.com>
> > > [Ezequiel: Add rockchip,rk3566-gmac compatible string]
> > > Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
> > > ---
> > >  .../bindings/net/rockchip-dwmac.txt           |   2 +
> > >  .../net/ethernet/stmicro/stmmac/dwmac-rk.c    | 142 ++++++++++++++++++
> > >  2 files changed, 144 insertions(+)
> > >
> > > diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
> > > index 3b71da7e8742..80203b16b652 100644
> > > --- a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
> > > +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
> > > @@ -12,6 +12,8 @@ Required properties:
> > >     "rockchip,rk3366-gmac": found on RK3366 SoCs
> > >     "rockchip,rk3368-gmac": found on RK3368 SoCs
> > >     "rockchip,rk3399-gmac": found on RK3399 SoCs
> > > +   "rockchip,rk3566-gmac": found on RK3566 SoCs
> > > +   "rockchip,rk3568-gmac": found on RK3568 SoCs
> > >     "rockchip,rv1108-gmac": found on RV1108 SoCs
> > >   - reg: addresses and length of the register sets for the device.
> > >   - interrupts: Should contain the GMAC interrupts.
> > > diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
> > > index d2637d83899e..096965b0fec9 100644
> > > --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
> > > +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
> > > @@ -948,6 +948,146 @@ static const struct rk_gmac_ops rk3399_ops = {
> > >         .set_rmii_speed = rk3399_set_rmii_speed,
> > >  };
> > >
> > > +#define RK3568_GRF_GMAC0_CON0          0x0380
> > > +#define RK3568_GRF_GMAC0_CON1          0x0384
> > > +#define RK3568_GRF_GMAC1_CON0          0x0388
> > > +#define RK3568_GRF_GMAC1_CON1          0x038c
> > > +
> > > +/* RK3568_GRF_GMAC0_CON1 && RK3568_GRF_GMAC1_CON1 */
> > > +#define RK3568_GMAC_PHY_INTF_SEL_RGMII \
> > > +               (GRF_BIT(4) | GRF_CLR_BIT(5) | GRF_CLR_BIT(6))
> > > +#define RK3568_GMAC_PHY_INTF_SEL_RMII  \
> > > +               (GRF_CLR_BIT(4) | GRF_CLR_BIT(5) | GRF_BIT(6))
> > > +#define RK3568_GMAC_FLOW_CTRL                  GRF_BIT(3)
> > > +#define RK3568_GMAC_FLOW_CTRL_CLR              GRF_CLR_BIT(3)
> > > +#define RK3568_GMAC_RXCLK_DLY_ENABLE           GRF_BIT(1)
> > > +#define RK3568_GMAC_RXCLK_DLY_DISABLE          GRF_CLR_BIT(1)
> > > +#define RK3568_GMAC_TXCLK_DLY_ENABLE           GRF_BIT(0)
> > > +#define RK3568_GMAC_TXCLK_DLY_DISABLE          GRF_CLR_BIT(0)
> > > +
> > > +/* RK3568_GRF_GMAC0_CON0 && RK3568_GRF_GMAC1_CON0 */
> > > +#define RK3568_GMAC_CLK_RX_DL_CFG(val) HIWORD_UPDATE(val, 0x7F, 8)
> > > +#define RK3568_GMAC_CLK_TX_DL_CFG(val) HIWORD_UPDATE(val, 0x7F, 0)
> > > +
> > > +static void rk3566_set_to_rgmii(struct rk_priv_data *bsp_priv,
> > > +                               int tx_delay, int rx_delay)
> > > +{
> > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > +
> > > +       if (IS_ERR(bsp_priv->grf)) {
> > > +               dev_err(dev, "Missing rockchip,grf property\n");
> > > +               return;
> > > +       }
> > > +
> > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > > +
> > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON0,
> > > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> > > +}
> > > +
> > > +static void rk3566_set_to_rmii(struct rk_priv_data *bsp_priv)
> > > +{
> > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > +
> > > +       if (IS_ERR(bsp_priv->grf)) {
> > > +               dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
> > > +               return;
> > > +       }
> > > +
> > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > > +                    RK3568_GMAC_PHY_INTF_SEL_RMII);
> > > +}
> > > +
> > > +static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
> > > +                               int tx_delay, int rx_delay)
> > > +{
> > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > +
> > > +       if (IS_ERR(bsp_priv->grf)) {
> > > +               dev_err(dev, "Missing rockchip,grf property\n");
> > > +               return;
> > > +       }
> > > +
> > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON1,
> > > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > > +
> > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON0,
> > > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> > > +
> > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > > +
> > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON0,
> > > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> >
> > Since there are two GMACs on the rk3568, and either, or, or both may
> > be enabled in various configurations, we should only configure the
> > controller we are currently operating.

Perhaps we should have match data (such as reg = <0>, or against the
address) to identify the individual controllers.

> >
> > > +}
> > > +
> > > +static void rk3568_set_to_rmii(struct rk_priv_data *bsp_priv)
> > > +{
> > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > +
> > > +       if (IS_ERR(bsp_priv->grf)) {
> > > +               dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
> > > +               return;
> > > +       }
> > > +
> > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON1,
> > > +                    RK3568_GMAC_PHY_INTF_SEL_RMII);
> > > +
> > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > > +                    RK3568_GMAC_PHY_INTF_SEL_RMII);
> >
> > Same as above.
> >
> > > +}
> > > +
> > > +static void rk3568_set_gmac_speed(struct rk_priv_data *bsp_priv, int speed)
> > > +{
> > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > +       unsigned long rate;
> > > +       int ret;
> > > +
> > > +       switch (speed) {
> > > +       case 10:
> > > +               rate = 2500000;
> > > +               break;
> > > +       case 100:
> > > +               rate = 25000000;
> > > +               break;
> > > +       case 1000:
> > > +               rate = 125000000;
> > > +               break;
> > > +       default:
> > > +               dev_err(dev, "unknown speed value for GMAC speed=%d", speed);
> > > +               return;
> > > +       }
> > > +
> > > +       ret = clk_set_rate(bsp_priv->clk_mac_speed, rate);
> > > +       if (ret)
> > > +               dev_err(dev, "%s: set clk_mac_speed rate %ld failed %d\n",
> > > +                       __func__, rate, ret);
> > > +}
> > > +
> > > +static const struct rk_gmac_ops rk3568_ops = {
> > > +       .set_to_rgmii = rk3568_set_to_rgmii,
> > > +       .set_to_rmii = rk3568_set_to_rmii,
> > > +       .set_rgmii_speed = rk3568_set_gmac_speed,
> > > +       .set_rmii_speed = rk3568_set_gmac_speed,
> > > +};
> > > +
> > > +static const struct rk_gmac_ops rk3566_ops = {
> > > +       .set_to_rgmii = rk3566_set_to_rgmii,
> > > +       .set_to_rmii = rk3566_set_to_rmii,
> > > +       .set_rgmii_speed = rk3568_set_gmac_speed,
> > > +       .set_rmii_speed = rk3568_set_gmac_speed,
> > > +};
> > > +
> > >  #define RV1108_GRF_GMAC_CON0           0X0900
> > >
> > >  /* RV1108_GRF_GMAC_CON0 */
> > > @@ -1512,6 +1652,8 @@ static const struct of_device_id rk_gmac_dwmac_match[] = {
> > >         { .compatible = "rockchip,rk3366-gmac", .data = &rk3366_ops },
> > >         { .compatible = "rockchip,rk3368-gmac", .data = &rk3368_ops },
> > >         { .compatible = "rockchip,rk3399-gmac", .data = &rk3399_ops },
> > > +       { .compatible = "rockchip,rk3568-gmac", .data = &rk3568_ops },
> > > +       { .compatible = "rockchip,rk3566-gmac", .data = &rk3566_ops },
> > >         { .compatible = "rockchip,rv1108-gmac", .data = &rv1108_ops },
> > >         { }
> > >  };
> > > --
> > > 2.30.0
> > >
>
Heiko Stübner April 14, 2021, 11:15 a.m. UTC | #4
Am Mittwoch, 14. April 2021, 13:03:25 CEST schrieb Peter Geis:
> On Tue, Apr 13, 2021 at 7:37 PM Ezequiel Garcia <ezequiel@collabora.com> wrote:
> > > > +static void rk3566_set_to_rmii(struct rk_priv_data *bsp_priv)
> > > > +{
> > > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > > +
> > > > +       if (IS_ERR(bsp_priv->grf)) {
> > > > +               dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
> > > > +               return;
> > > > +       }
> > > > +
> > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > > > +                    RK3568_GMAC_PHY_INTF_SEL_RMII);
> > > > +}
> > > > +
> > > > +static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
> > > > +                               int tx_delay, int rx_delay)
> > > > +{
> > > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > > +
> > > > +       if (IS_ERR(bsp_priv->grf)) {
> > > > +               dev_err(dev, "Missing rockchip,grf property\n");
> > > > +               return;
> > > > +       }
> > > > +
> > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON1,
> > > > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > > > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > > > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > > > +
> > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON0,
> > > > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > > > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> > > > +
> > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > > > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > > > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > > > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > > > +
> > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON0,
> > > > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > > > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> > >
> > > Since there are two GMACs on the rk3568, and either, or, or both may
> > > be enabled in various configurations, we should only configure the
> > > controller we are currently operating.
> 
> Perhaps we should have match data (such as reg = <0>, or against the
> address) to identify the individual controllers.

Hmm, "reg" will be used by the actual mmio address of the controller,
so matching against that should be the way I guess.

We're already doing something similar for dsi:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c#n1170


Heiko
Ezequiel Garcia April 14, 2021, 1:48 p.m. UTC | #5
Hi Peter, Heiko,

On Wed, 2021-04-14 at 13:15 +0200, Heiko Stübner wrote:
> Am Mittwoch, 14. April 2021, 13:03:25 CEST schrieb Peter Geis:
> > On Tue, Apr 13, 2021 at 7:37 PM Ezequiel Garcia <ezequiel@collabora.com> wrote:
> > > > > +static void rk3566_set_to_rmii(struct rk_priv_data *bsp_priv)
> > > > > +{
> > > > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > > > +
> > > > > +       if (IS_ERR(bsp_priv->grf)) {
> > > > > +               dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
> > > > > +               return;
> > > > > +       }
> > > > > +
> > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > > > > +                    RK3568_GMAC_PHY_INTF_SEL_RMII);
> > > > > +}
> > > > > +
> > > > > +static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
> > > > > +                               int tx_delay, int rx_delay)
> > > > > +{
> > > > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > > > +
> > > > > +       if (IS_ERR(bsp_priv->grf)) {
> > > > > +               dev_err(dev, "Missing rockchip,grf property\n");
> > > > > +               return;
> > > > > +       }
> > > > > +
> > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON1,
> > > > > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > > > > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > > > > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > > > > +
> > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON0,
> > > > > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > > > > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> > > > > +
> > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > > > > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > > > > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > > > > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > > > > +
> > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON0,
> > > > > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > > > > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> > > > 
> > > > Since there are two GMACs on the rk3568, and either, or, or both may
> > > > be enabled in various configurations, we should only configure the
> > > > controller we are currently operating.
> > 
> > Perhaps we should have match data (such as reg = <0>, or against the
> > address) to identify the individual controllers.
> 
> Hmm, "reg" will be used by the actual mmio address of the controller,
> so matching against that should be the way I guess.
> 
> We're already doing something similar for dsi:
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c#n1170
> 

I have to admit, I'm not a fan of hardcoding the registers in the kernel.

David Wu solved this in the downstream kernel by using bus_id,
which parses the devicetree "ethernet@0" node, i.e.:

  plat->bus_id = of_alias_get_id(np, "ethernet");

I'm inclined for this solution. Maybe Jose can suggest how to approach it?

Thanks!
Ezequiel
Ezequiel Garcia April 14, 2021, 1:48 p.m. UTC | #6
On Wed, 2021-04-14 at 07:03 -0400, Peter Geis wrote:
> On Tue, Apr 13, 2021 at 7:37 PM Ezequiel Garcia <ezequiel@collabora.com> wrote:
> > 
> > On Tuesday, April 13, 2021 19:51 -03, Peter Geis <pgwipeout@gmail.com> wrote:
> > 
> > > On Tue, Apr 13, 2021 at 5:03 PM Ezequiel Garcia <ezequiel@collabora.com> wrote:
> > > > 
> > > > From: David Wu <david.wu@rock-chips.com>
> > > > 
> > > > Add constants and callback functions for the dwmac present
> > > > on RK3566 and RK3568 SoCs. As can be seen, the base structure
> > > > is the same, only registers and the bits in them moved slightly.
> > > > 
> > > > RK3568 supports two MACs, and RK3566 support just one.
> > > 
> > > Tested this driver on the rk3566-quartz64.
> > > It fails to fully probe the gmac with the following error:
> > > [    5.711127] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found
> > > [    5.714147] rk_gmac-dwmac fe010000.ethernet: no regulator found
> > > [    5.714766] rk_gmac-dwmac fe010000.ethernet: clock input or output? (input).
> > > [    5.715474] rk_gmac-dwmac fe010000.ethernet: TX delay(0x4f).
> > > [    5.716058] rk_gmac-dwmac fe010000.ethernet: RX delay(0x25).
> > > [    5.716694] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
> > > [    5.718413] rk_gmac-dwmac fe010000.ethernet: clock input from PHY
> > > [    5.724140] rk_gmac-dwmac fe010000.ethernet: init for RGMII
> > > [    5.726802] rk_gmac-dwmac fe010000.ethernet: Version ID not available
> > > [    5.727525] rk_gmac-dwmac fe010000.ethernet:         DWMAC1000
> > > [    5.728064] rk_gmac-dwmac fe010000.ethernet: DMA HW capability
> > > register supported
> > > [    5.729026] rk_gmac-dwmac fe010000.ethernet: Normal descriptors
> > > [    5.729624] rk_gmac-dwmac fe010000.ethernet: Ring mode enabled
> > > [    5.731123] rk_gmac-dwmac fe010000.ethernet: Unbalanced pm_runtime_enable!
> > > [    5.873329] libphy: stmmac: probed
> > > [    5.905599] rk_gmac-dwmac fe010000.ethernet: Cannot register the MDIO bus
> > > [    5.906335] rk_gmac-dwmac fe010000.ethernet: stmmac_dvr_probe: MDIO
> > > bus (id: 1) registration failed
> > > [    5.914338] rk_gmac-dwmac: probe of fe010000.ethernet failed with error -5
> > > 
> > > This is due to the lack of setting has_gmac4 = true.
> > > 
> > 
> > You are probably missing a "snps,dwmac-4.20a" in your compatible string, i.e.:
> >   compatible = "rockchip,rk3566-gmac", "snps,dwmac-4.20a";
> 
> Ah yes, I had disabled that because my variant took a different path.
> Thanks!
> 

Is that a Tested-by :-) ?

Thanks,
Ezequiel
Chen-Yu Tsai April 14, 2021, 4:33 p.m. UTC | #7
On Thu, Apr 15, 2021 at 12:14 AM Ezequiel Garcia <ezequiel@collabora.com> wrote:
>
> Hi Peter, Heiko,
>
> On Wed, 2021-04-14 at 13:15 +0200, Heiko Stübner wrote:
> > Am Mittwoch, 14. April 2021, 13:03:25 CEST schrieb Peter Geis:
> > > On Tue, Apr 13, 2021 at 7:37 PM Ezequiel Garcia <ezequiel@collabora.com> wrote:
> > > > > > +static void rk3566_set_to_rmii(struct rk_priv_data *bsp_priv)
> > > > > > +{
> > > > > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > > > > +
> > > > > > +       if (IS_ERR(bsp_priv->grf)) {
> > > > > > +               dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
> > > > > > +               return;
> > > > > > +       }
> > > > > > +
> > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > > > > > +                    RK3568_GMAC_PHY_INTF_SEL_RMII);
> > > > > > +}
> > > > > > +
> > > > > > +static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
> > > > > > +                               int tx_delay, int rx_delay)
> > > > > > +{
> > > > > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > > > > +
> > > > > > +       if (IS_ERR(bsp_priv->grf)) {
> > > > > > +               dev_err(dev, "Missing rockchip,grf property\n");
> > > > > > +               return;
> > > > > > +       }
> > > > > > +
> > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON1,
> > > > > > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > > > > > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > > > > > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > > > > > +
> > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON0,
> > > > > > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > > > > > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> > > > > > +
> > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > > > > > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > > > > > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > > > > > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > > > > > +
> > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON0,
> > > > > > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > > > > > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> > > > >
> > > > > Since there are two GMACs on the rk3568, and either, or, or both may
> > > > > be enabled in various configurations, we should only configure the
> > > > > controller we are currently operating.
> > >
> > > Perhaps we should have match data (such as reg = <0>, or against the
> > > address) to identify the individual controllers.
> >
> > Hmm, "reg" will be used by the actual mmio address of the controller,
> > so matching against that should be the way I guess.
> >
> > We're already doing something similar for dsi:
> > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c#n1170
> >
>
> I have to admit, I'm not a fan of hardcoding the registers in the kernel.
>
> David Wu solved this in the downstream kernel by using bus_id,
> which parses the devicetree "ethernet@0" node, i.e.:
>
>   plat->bus_id = of_alias_get_id(np, "ethernet");

What happens when one adds another ethernet controller (USB or PCIe) to
the board and wants to change the numbering order?

Or maybe only the second ethernet controller is routed on some board
and the submitter / vendor wants that one to be ethernet0, because
it's the only usable controller?

This seems even more fragile than hardcoding the registers.

Regards
ChenYu
Heiko Stübner April 14, 2021, 4:35 p.m. UTC | #8
Am Mittwoch, 14. April 2021, 18:33:12 CEST schrieb Chen-Yu Tsai:
> On Thu, Apr 15, 2021 at 12:14 AM Ezequiel Garcia <ezequiel@collabora.com> wrote:
> >
> > Hi Peter, Heiko,
> >
> > On Wed, 2021-04-14 at 13:15 +0200, Heiko Stübner wrote:
> > > Am Mittwoch, 14. April 2021, 13:03:25 CEST schrieb Peter Geis:
> > > > On Tue, Apr 13, 2021 at 7:37 PM Ezequiel Garcia <ezequiel@collabora.com> wrote:
> > > > > > > +static void rk3566_set_to_rmii(struct rk_priv_data *bsp_priv)
> > > > > > > +{
> > > > > > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > > > > > +
> > > > > > > +       if (IS_ERR(bsp_priv->grf)) {
> > > > > > > +               dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
> > > > > > > +               return;
> > > > > > > +       }
> > > > > > > +
> > > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > > > > > > +                    RK3568_GMAC_PHY_INTF_SEL_RMII);
> > > > > > > +}
> > > > > > > +
> > > > > > > +static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
> > > > > > > +                               int tx_delay, int rx_delay)
> > > > > > > +{
> > > > > > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > > > > > +
> > > > > > > +       if (IS_ERR(bsp_priv->grf)) {
> > > > > > > +               dev_err(dev, "Missing rockchip,grf property\n");
> > > > > > > +               return;
> > > > > > > +       }
> > > > > > > +
> > > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON1,
> > > > > > > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > > > > > > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > > > > > > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > > > > > > +
> > > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON0,
> > > > > > > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > > > > > > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> > > > > > > +
> > > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > > > > > > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > > > > > > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > > > > > > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > > > > > > +
> > > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON0,
> > > > > > > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > > > > > > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> > > > > >
> > > > > > Since there are two GMACs on the rk3568, and either, or, or both may
> > > > > > be enabled in various configurations, we should only configure the
> > > > > > controller we are currently operating.
> > > >
> > > > Perhaps we should have match data (such as reg = <0>, or against the
> > > > address) to identify the individual controllers.
> > >
> > > Hmm, "reg" will be used by the actual mmio address of the controller,
> > > so matching against that should be the way I guess.
> > >
> > > We're already doing something similar for dsi:
> > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c#n1170
> > >
> >
> > I have to admit, I'm not a fan of hardcoding the registers in the kernel.
> >
> > David Wu solved this in the downstream kernel by using bus_id,
> > which parses the devicetree "ethernet@0" node, i.e.:
> >
> >   plat->bus_id = of_alias_get_id(np, "ethernet");
> 
> What happens when one adds another ethernet controller (USB or PCIe) to
> the board and wants to change the numbering order?
> 
> Or maybe only the second ethernet controller is routed on some board
> and the submitter / vendor wants that one to be ethernet0, because
> it's the only usable controller?

Which matches a discussion I had with Arnd about the mmc numbering.
I.e. there the first mmc device is supposed to be mmc0 and so on,
without gaps - for probably the same reasons.


> 
> This seems even more fragile than hardcoding the registers.
> 
> Regards
> ChenYu
>
Ezequiel Garcia April 14, 2021, 4:44 p.m. UTC | #9
On Wed, 2021-04-14 at 18:35 +0200, Heiko Stübner wrote:
> Am Mittwoch, 14. April 2021, 18:33:12 CEST schrieb Chen-Yu Tsai:
> > On Thu, Apr 15, 2021 at 12:14 AM Ezequiel Garcia <ezequiel@collabora.com> wrote:
> > > 
> > > Hi Peter, Heiko,
> > > 
> > > On Wed, 2021-04-14 at 13:15 +0200, Heiko Stübner wrote:
> > > > Am Mittwoch, 14. April 2021, 13:03:25 CEST schrieb Peter Geis:
> > > > > On Tue, Apr 13, 2021 at 7:37 PM Ezequiel Garcia <ezequiel@collabora.com> wrote:
> > > > > > > > +static void rk3566_set_to_rmii(struct rk_priv_data *bsp_priv)
> > > > > > > > +{
> > > > > > > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > > > > > > +
> > > > > > > > +       if (IS_ERR(bsp_priv->grf)) {
> > > > > > > > +               dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
> > > > > > > > +               return;
> > > > > > > > +       }
> > > > > > > > +
> > > > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > > > > > > > +                    RK3568_GMAC_PHY_INTF_SEL_RMII);
> > > > > > > > +}
> > > > > > > > +
> > > > > > > > +static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
> > > > > > > > +                               int tx_delay, int rx_delay)
> > > > > > > > +{
> > > > > > > > +       struct device *dev = &bsp_priv->pdev->dev;
> > > > > > > > +
> > > > > > > > +       if (IS_ERR(bsp_priv->grf)) {
> > > > > > > > +               dev_err(dev, "Missing rockchip,grf property\n");
> > > > > > > > +               return;
> > > > > > > > +       }
> > > > > > > > +
> > > > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON1,
> > > > > > > > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > > > > > > > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > > > > > > > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > > > > > > > +
> > > > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON0,
> > > > > > > > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > > > > > > > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> > > > > > > > +
> > > > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
> > > > > > > > +                    RK3568_GMAC_PHY_INTF_SEL_RGMII |
> > > > > > > > +                    RK3568_GMAC_RXCLK_DLY_ENABLE |
> > > > > > > > +                    RK3568_GMAC_TXCLK_DLY_ENABLE);
> > > > > > > > +
> > > > > > > > +       regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON0,
> > > > > > > > +                    RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
> > > > > > > > +                    RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
> > > > > > > 
> > > > > > > Since there are two GMACs on the rk3568, and either, or, or both may
> > > > > > > be enabled in various configurations, we should only configure the
> > > > > > > controller we are currently operating.
> > > > > 
> > > > > Perhaps we should have match data (such as reg = <0>, or against the
> > > > > address) to identify the individual controllers.
> > > > 
> > > > Hmm, "reg" will be used by the actual mmio address of the controller,
> > > > so matching against that should be the way I guess.
> > > > 
> > > > We're already doing something similar for dsi:
> > > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/gpu/drm/rockchip/dw-mipi-dsi-rockchip.c#n1170
> > > > 
> > > 
> > > I have to admit, I'm not a fan of hardcoding the registers in the kernel.
> > > 
> > > David Wu solved this in the downstream kernel by using bus_id,
> > > which parses the devicetree "ethernet@0" node, i.e.:
> > > 
> > >   plat->bus_id = of_alias_get_id(np, "ethernet");
> > 
> > What happens when one adds another ethernet controller (USB or PCIe) to
> > the board and wants to change the numbering order?
> > 
> > Or maybe only the second ethernet controller is routed on some board
> > and the submitter / vendor wants that one to be ethernet0, because
> > it's the only usable controller?
> 
> Which matches a discussion I had with Arnd about the mmc numbering.
> I.e. there the first mmc device is supposed to be mmc0 and so on,
> without gaps - for probably the same reasons.
> 
> 

Well, given each controller has its own register space, maybe
just model it with a new reg cell or a DT property that is able
to directly encode the base address?

Looking at the vendor kernel, XPCS will have another set of registers,
separate for each MAC.

Thanks,
Ezequiel

> > 
> > This seems even more fragile than hardcoding the registers.
> > 
> > Regards
> > ChenYu
> > 
> 
> 
> 
>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
index 3b71da7e8742..80203b16b652 100644
--- a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
+++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
@@ -12,6 +12,8 @@  Required properties:
    "rockchip,rk3366-gmac": found on RK3366 SoCs
    "rockchip,rk3368-gmac": found on RK3368 SoCs
    "rockchip,rk3399-gmac": found on RK3399 SoCs
+   "rockchip,rk3566-gmac": found on RK3566 SoCs
+   "rockchip,rk3568-gmac": found on RK3568 SoCs
    "rockchip,rv1108-gmac": found on RV1108 SoCs
  - reg: addresses and length of the register sets for the device.
  - interrupts: Should contain the GMAC interrupts.
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
index d2637d83899e..096965b0fec9 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
@@ -948,6 +948,146 @@  static const struct rk_gmac_ops rk3399_ops = {
 	.set_rmii_speed = rk3399_set_rmii_speed,
 };
 
+#define RK3568_GRF_GMAC0_CON0		0x0380
+#define RK3568_GRF_GMAC0_CON1		0x0384
+#define RK3568_GRF_GMAC1_CON0		0x0388
+#define RK3568_GRF_GMAC1_CON1		0x038c
+
+/* RK3568_GRF_GMAC0_CON1 && RK3568_GRF_GMAC1_CON1 */
+#define RK3568_GMAC_PHY_INTF_SEL_RGMII	\
+		(GRF_BIT(4) | GRF_CLR_BIT(5) | GRF_CLR_BIT(6))
+#define RK3568_GMAC_PHY_INTF_SEL_RMII	\
+		(GRF_CLR_BIT(4) | GRF_CLR_BIT(5) | GRF_BIT(6))
+#define RK3568_GMAC_FLOW_CTRL			GRF_BIT(3)
+#define RK3568_GMAC_FLOW_CTRL_CLR		GRF_CLR_BIT(3)
+#define RK3568_GMAC_RXCLK_DLY_ENABLE		GRF_BIT(1)
+#define RK3568_GMAC_RXCLK_DLY_DISABLE		GRF_CLR_BIT(1)
+#define RK3568_GMAC_TXCLK_DLY_ENABLE		GRF_BIT(0)
+#define RK3568_GMAC_TXCLK_DLY_DISABLE		GRF_CLR_BIT(0)
+
+/* RK3568_GRF_GMAC0_CON0 && RK3568_GRF_GMAC1_CON0 */
+#define RK3568_GMAC_CLK_RX_DL_CFG(val)	HIWORD_UPDATE(val, 0x7F, 8)
+#define RK3568_GMAC_CLK_TX_DL_CFG(val)	HIWORD_UPDATE(val, 0x7F, 0)
+
+static void rk3566_set_to_rgmii(struct rk_priv_data *bsp_priv,
+				int tx_delay, int rx_delay)
+{
+	struct device *dev = &bsp_priv->pdev->dev;
+
+	if (IS_ERR(bsp_priv->grf)) {
+		dev_err(dev, "Missing rockchip,grf property\n");
+		return;
+	}
+
+	regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
+		     RK3568_GMAC_PHY_INTF_SEL_RGMII |
+		     RK3568_GMAC_RXCLK_DLY_ENABLE |
+		     RK3568_GMAC_TXCLK_DLY_ENABLE);
+
+	regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON0,
+		     RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
+		     RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
+}
+
+static void rk3566_set_to_rmii(struct rk_priv_data *bsp_priv)
+{
+	struct device *dev = &bsp_priv->pdev->dev;
+
+	if (IS_ERR(bsp_priv->grf)) {
+		dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
+		return;
+	}
+
+	regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
+		     RK3568_GMAC_PHY_INTF_SEL_RMII);
+}
+
+static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
+				int tx_delay, int rx_delay)
+{
+	struct device *dev = &bsp_priv->pdev->dev;
+
+	if (IS_ERR(bsp_priv->grf)) {
+		dev_err(dev, "Missing rockchip,grf property\n");
+		return;
+	}
+
+	regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON1,
+		     RK3568_GMAC_PHY_INTF_SEL_RGMII |
+		     RK3568_GMAC_RXCLK_DLY_ENABLE |
+		     RK3568_GMAC_TXCLK_DLY_ENABLE);
+
+	regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON0,
+		     RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
+		     RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
+
+	regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
+		     RK3568_GMAC_PHY_INTF_SEL_RGMII |
+		     RK3568_GMAC_RXCLK_DLY_ENABLE |
+		     RK3568_GMAC_TXCLK_DLY_ENABLE);
+
+	regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON0,
+		     RK3568_GMAC_CLK_RX_DL_CFG(rx_delay) |
+		     RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
+}
+
+static void rk3568_set_to_rmii(struct rk_priv_data *bsp_priv)
+{
+	struct device *dev = &bsp_priv->pdev->dev;
+
+	if (IS_ERR(bsp_priv->grf)) {
+		dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
+		return;
+	}
+
+	regmap_write(bsp_priv->grf, RK3568_GRF_GMAC0_CON1,
+		     RK3568_GMAC_PHY_INTF_SEL_RMII);
+
+	regmap_write(bsp_priv->grf, RK3568_GRF_GMAC1_CON1,
+		     RK3568_GMAC_PHY_INTF_SEL_RMII);
+}
+
+static void rk3568_set_gmac_speed(struct rk_priv_data *bsp_priv, int speed)
+{
+	struct device *dev = &bsp_priv->pdev->dev;
+	unsigned long rate;
+	int ret;
+
+	switch (speed) {
+	case 10:
+		rate = 2500000;
+		break;
+	case 100:
+		rate = 25000000;
+		break;
+	case 1000:
+		rate = 125000000;
+		break;
+	default:
+		dev_err(dev, "unknown speed value for GMAC speed=%d", speed);
+		return;
+	}
+
+	ret = clk_set_rate(bsp_priv->clk_mac_speed, rate);
+	if (ret)
+		dev_err(dev, "%s: set clk_mac_speed rate %ld failed %d\n",
+			__func__, rate, ret);
+}
+
+static const struct rk_gmac_ops rk3568_ops = {
+	.set_to_rgmii = rk3568_set_to_rgmii,
+	.set_to_rmii = rk3568_set_to_rmii,
+	.set_rgmii_speed = rk3568_set_gmac_speed,
+	.set_rmii_speed = rk3568_set_gmac_speed,
+};
+
+static const struct rk_gmac_ops rk3566_ops = {
+	.set_to_rgmii = rk3566_set_to_rgmii,
+	.set_to_rmii = rk3566_set_to_rmii,
+	.set_rgmii_speed = rk3568_set_gmac_speed,
+	.set_rmii_speed = rk3568_set_gmac_speed,
+};
+
 #define RV1108_GRF_GMAC_CON0		0X0900
 
 /* RV1108_GRF_GMAC_CON0 */
@@ -1512,6 +1652,8 @@  static const struct of_device_id rk_gmac_dwmac_match[] = {
 	{ .compatible = "rockchip,rk3366-gmac", .data = &rk3366_ops },
 	{ .compatible = "rockchip,rk3368-gmac", .data = &rk3368_ops },
 	{ .compatible = "rockchip,rk3399-gmac", .data = &rk3399_ops },
+	{ .compatible = "rockchip,rk3568-gmac", .data = &rk3568_ops },
+	{ .compatible = "rockchip,rk3566-gmac", .data = &rk3566_ops },
 	{ .compatible = "rockchip,rv1108-gmac", .data = &rv1108_ops },
 	{ }
 };