[v1,3/4] arm64: dts: rockchip: rk3588-rock5b: add USB2

Commit Message

Sebastian Reichel July 12, 2023, 4:51 p.m. UTC

Enable USB2 (EHCI and OCHI mode) support for the Radxa ROCK 5 Model B.
This adds USB support on the M.2 Key E, both USB2 ports and USB2 mode
for the upper USB3 port (the one further away from the PCB).

The lower USB3 (closer to the PCB) and the USB-C ports use the RK3588
USB TypeC host controller, which is not yet supported upstream.

Signed-off-by: Sebastian Reichel <[e-mail]>
---
 .../boot/dts/rockchip/rk3588-rock-5b.dts      | 55 +++++++++++++++++++
 1 file changed, 55 insertions(+)

Patch

diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts
index 9cea262998b4..6be759903411 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts
@@ -43,6 +43,20 @@  fan: pwm-fan {
 		#cooling-cells = <2>;
 	};
 
+	vcc5v0_host: vcc5v0-host-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_host";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_host_en>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
 	vcc5v0_sys: vcc5v0-sys-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc5v0_sys";
@@ -201,6 +215,12 @@  hp_detect: hp-detect {
 			rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
+
+	usb {
+		vcc5v0_host_en: vcc5v0-host-en {
+			rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
 };
 
 &pwm1 {
@@ -564,3 +584,38 @@  &uart2 {
 	pinctrl-0 = <&uart2m0_xfer>;
 	status = "okay";
 };
+
+&u2phy2 {
+	status = "okay";
+};
+
+&u2phy2_host {
+	/* connected to USB hub, which is powered by vcc5v0_sys */
+	phy-supply = <&vcc5v0_sys>;
+	status = "okay";
+};
+
+&u2phy3 {
+	status = "okay";
+};
+
+&u2phy3_host {
+	phy-supply = <&vcc5v0_host>;
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};