diff mbox series

[7/8] ARM: dts: Add Sonoff iHost Smart Home Hub

Message ID 20231113120705.1647498-8-tim@feathertop.org (mailing list archive)
State New
Headers show
Series Add support for Sonoff iHost RV1126 Smart Home Gateway | expand

Commit Message

Tim Lunn Nov. 13, 2023, 12:07 p.m. UTC 
Sonoff iHost is gateway device designed to provide a Smart Home Hub,
it is based on Rockchip RV1126. There is also a version with 2GB RAM
based off the RV1109 dual core SoC.

Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone

This patch adds the initial device tree for this device, it is largely
based off the device trees for mainline Edgeble Neu2 and downstream
Rockchip rv1126-evb-v13 configs. It has been adapted with relevant
peripheral and GPIO pins for the iHost.

Signed-off-by: Tim Lunn <tim@feathertop.org>
---

 arch/arm/boot/dts/rockchip/Makefile           |   2 +
 .../boot/dts/rockchip/rv1109-sonoff-ihost.dts |  13 +
 arch/arm/boot/dts/rockchip/rv1109.dtsi        |  23 +
 .../boot/dts/rockchip/rv1126-sonoff-ihost.dts |  13 +
 .../dts/rockchip/rv1126-sonoff-ihost.dtsi     | 409 ++++++++++++++++++
 5 files changed, 460 insertions(+)
 create mode 100644 arch/arm/boot/dts/rockchip/rv1109-sonoff-ihost.dts
 create mode 100644 arch/arm/boot/dts/rockchip/rv1109.dtsi
 create mode 100644 arch/arm/boot/dts/rockchip/rv1126-sonoff-ihost.dts
 create mode 100644 arch/arm/boot/dts/rockchip/rv1126-sonoff-ihost.dtsi

Comments

Heiko Stuebner Nov. 18, 2023, 12:09 p.m. UTC | #1 
Hi Tim,

Am Montag, 13. November 2023, 13:07:04 CET schrieb Tim Lunn:
> Sonoff iHost is gateway device designed to provide a Smart Home Hub,
> it is based on Rockchip RV1126. There is also a version with 2GB RAM
> based off the RV1109 dual core SoC.
> 
> Features:
> - Rockchip RV1126
> - 4GB DDR4
> - 8GB eMMC
> - microSD slot
> - RMII Ethernet PHY
> - 1x USB 2.0 Host
> - 1x USB 2.0 OTG
> - Realtek RTL8723DS WiFi/BT
> - EFR32MG21 Silabs Zigbee radio
> - Speaker/Microphone
> 
> This patch adds the initial device tree for this device, it is largely
> based off the device trees for mainline Edgeble Neu2 and downstream
> Rockchip rv1126-evb-v13 configs. It has been adapted with relevant
> peripheral and GPIO pins for the iHost.
> 
> Signed-off-by: Tim Lunn <tim@feathertop.org>


> diff --git a/arch/arm/boot/dts/rockchip/rv1109.dtsi b/arch/arm/boot/dts/rockchip/rv1109.dtsi
> new file mode 100644
> index 000000000000..9cbaa08ab1b8
> --- /dev/null
> +++ b/arch/arm/boot/dts/rockchip/rv1109.dtsi
> @@ -0,0 +1,23 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd.
> + */
> +
> +/dts-v1/;
> +
> +#include "rv1126.dtsi"
> +
> +/ {
> +	compatible = "rockchip,rv1109";
> +
> +	cpus {
> +		/delete-node/ cpu@f02;
> +		/delete-node/ cpu@f03;
> +	};
> +
> +	arm-pmu {
> +		interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
> +		interrupt-affinity = <&cpu0>, <&cpu1>;
> +	};
> +};

this definitly wants to be its own patch ;-) .

I.e. you add support for the rv1109, which seems to be the same as rv1126, just
with 2 instead of 4 cpu cores.




> +&sdio {
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	cap-sdio-irq;
> +	keep-power-in-suspend;
> +	max-frequency = <100000000>;
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +	non-removable;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sdmmc1_clk &sdmmc1_cmd &sdmmc1_bus4>;
> +	rockchip,default-sample-phase = <90>;
> +	sd-uhs-sdr104;
> +	vmmc-supply = <&vcc3v3_sys>;
> +	vqmmc-supply = <&vcc_1v8>;
> +	status = "okay";
> +	#address-cells = <1>;
> +	#size-cells = <0>;

I don't think the *-cells are needed here


Thanks
Heiko
Tim Lunn Nov. 19, 2023, 3:05 a.m. UTC | #2 
Hi Heiko,

On 11/18/23 23:09, Heiko Stübner wrote:
> Hi Tim,
>
> Am Montag, 13. November 2023, 13:07:04 CET schrieb Tim Lunn:
>> Sonoff iHost is gateway device designed to provide a Smart Home Hub,
>> it is based on Rockchip RV1126. There is also a version with 2GB RAM
>> based off the RV1109 dual core SoC.
>>
>> Features:
>> - Rockchip RV1126
>> - 4GB DDR4
>> - 8GB eMMC
>> - microSD slot
>> - RMII Ethernet PHY
>> - 1x USB 2.0 Host
>> - 1x USB 2.0 OTG
>> - Realtek RTL8723DS WiFi/BT
>> - EFR32MG21 Silabs Zigbee radio
>> - Speaker/Microphone
>>
>> This patch adds the initial device tree for this device, it is largely
>> based off the device trees for mainline Edgeble Neu2 and downstream
>> Rockchip rv1126-evb-v13 configs. It has been adapted with relevant
>> peripheral and GPIO pins for the iHost.
>>
>> Signed-off-by: Tim Lunn <tim@feathertop.org>
>
>> diff --git a/arch/arm/boot/dts/rockchip/rv1109.dtsi b/arch/arm/boot/dts/rockchip/rv1109.dtsi
>> new file mode 100644
>> index 000000000000..9cbaa08ab1b8
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/rockchip/rv1109.dtsi
>> @@ -0,0 +1,23 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd.
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "rv1126.dtsi"
>> +
>> +/ {
>> +	compatible = "rockchip,rv1109";
>> +
>> +	cpus {
>> +		/delete-node/ cpu@f02;
>> +		/delete-node/ cpu@f03;
>> +	};
>> +
>> +	arm-pmu {
>> +		interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
>> +			     <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
>> +		interrupt-affinity = <&cpu0>, <&cpu1>;
>> +	};
>> +};
> this definitly wants to be its own patch ;-) .
>
> I.e. you add support for the rv1109, which seems to be the same as rv1126, just
> with 2 instead of 4 cpu cores.
I will split this out. Yes, rv1109 is identical to the rv1126 apart from 
the number of cores.

I initially hoped rv1109 could just use the same device tree, but having 
the extra cores enabled ends
up causing panics.

>
>
>
>> +&sdio {
>> +	bus-width = <4>;
>> +	cap-sd-highspeed;
>> +	cap-sdio-irq;
>> +	keep-power-in-suspend;
>> +	max-frequency = <100000000>;
>> +	mmc-pwrseq = <&sdio_pwrseq>;
>> +	non-removable;
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&sdmmc1_clk &sdmmc1_cmd &sdmmc1_bus4>;
>> +	rockchip,default-sample-phase = <90>;
>> +	sd-uhs-sdr104;
>> +	vmmc-supply = <&vcc3v3_sys>;
>> +	vqmmc-supply = <&vcc_1v8>;
>> +	status = "okay";
>> +	#address-cells = <1>;
>> +	#size-cells = <0>;
> I don't think the *-cells are needed here
>
Ok, i will check and remove.

Regards
    Tim

>
> Thanks
> Heiko
>
>
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/rockchip/Makefile b/arch/arm/boot/dts/rockchip/Makefile
index 0f46e18fe275..4d4533d6f407 100644
--- a/arch/arm/boot/dts/rockchip/Makefile
+++ b/arch/arm/boot/dts/rockchip/Makefile
@@ -2,7 +2,9 @@ 
 dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rv1108-elgin-r1.dtb \
 	rv1108-evb.dtb \
+	rv1109-sonoff-ihost.dtb \
 	rv1126-edgeble-neu2-io.dtb \
+	rv1126-sonoff-ihost.dtb \
 	rk3036-evb.dtb \
 	rk3036-kylin.dtb \
 	rk3066a-bqcurie2.dtb \
diff --git a/arch/arm/boot/dts/rockchip/rv1109-sonoff-ihost.dts b/arch/arm/boot/dts/rockchip/rv1109-sonoff-ihost.dts
new file mode 100644
index 000000000000..3bfdb00ac8e1
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rv1109-sonoff-ihost.dts
@@ -0,0 +1,13 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ */
+
+/dts-v1/;
+#include "rv1109.dtsi"
+#include "rv1126-sonoff-ihost.dtsi"
+
+/ {
+	model = "Sonoff iHost 2G";
+	compatible = "itead,sonoff-ihost", "rockchip,rv1109";
+};
diff --git a/arch/arm/boot/dts/rockchip/rv1109.dtsi b/arch/arm/boot/dts/rockchip/rv1109.dtsi
new file mode 100644
index 000000000000..9cbaa08ab1b8
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rv1109.dtsi
@@ -0,0 +1,23 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd.
+ */
+
+/dts-v1/;
+
+#include "rv1126.dtsi"
+
+/ {
+	compatible = "rockchip,rv1109";
+
+	cpus {
+		/delete-node/ cpu@f02;
+		/delete-node/ cpu@f03;
+	};
+
+	arm-pmu {
+		interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+};
diff --git a/arch/arm/boot/dts/rockchip/rv1126-sonoff-ihost.dts b/arch/arm/boot/dts/rockchip/rv1126-sonoff-ihost.dts
new file mode 100644
index 000000000000..106d1e42f285
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rv1126-sonoff-ihost.dts
@@ -0,0 +1,13 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ */
+
+/dts-v1/;
+#include "rv1126.dtsi"
+#include "rv1126-sonoff-ihost.dtsi"
+
+/ {
+	model = "Sonoff iHost 4G";
+	compatible = "itead,sonoff-ihost", "rockchip,rv1126";
+};
diff --git a/arch/arm/boot/dts/rockchip/rv1126-sonoff-ihost.dtsi b/arch/arm/boot/dts/rockchip/rv1126-sonoff-ihost.dtsi
new file mode 100644
index 000000000000..9060795d88f3
--- /dev/null
+++ b/arch/arm/boot/dts/rockchip/rv1126-sonoff-ihost.dtsi
@@ -0,0 +1,409 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2022 Edgeble AI Technologies Pvt. Ltd.
+ */
+
+/ {
+	aliases {
+		mmc0 = &emmc;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	vcc5v0_sys: regulator-vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	sdio_pwrseq: pwrseq-sdio {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk809 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+		reset-gpios = <&gpio1 RK_PD0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk &emmc_rstnout>;
+	rockchip,default-sample-phase = <90>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PB1 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "rk808-clkout1", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc5v0_sys>;
+		vcc2-supply = <&vcc5v0_sys>;
+		vcc3-supply = <&vcc5v0_sys>;
+		vcc4-supply = <&vcc5v0_sys>;
+		vcc5-supply = <&vcc_buck5>;
+		vcc6-supply = <&vcc_buck5>;
+		vcc7-supply = <&vcc5v0_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc5v0_sys>;
+
+		regulators {
+			vdd_npu_vepu: DCDC_REG1 {
+				regulator-name = "vdd_npu_vepu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <650000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_arm: DCDC_REG2 {
+				regulator-name = "vdd_arm";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <725000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc3v3_sys: DCDC_REG4 {
+				regulator-name = "vcc3v3_sys";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_buck5: DCDC_REG5 {
+				regulator-name = "vcc_buck5";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <2200000>;
+				regulator-max-microvolt = <2200000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <2200000>;
+				};
+			};
+
+			vcc_0v8: LDO_REG1 {
+				regulator-name = "vcc_0v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc1v8_pmu: LDO_REG2 {
+				regulator-name = "vcc1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd0v8_pmu: LDO_REG3 {
+				regulator-name = "vcc0v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <800000>;
+				};
+			};
+
+			vcc_1v8: LDO_REG4 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_dovdd: LDO_REG5 {
+				regulator-name = "vcc_dovdd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_dvdd: LDO_REG6 {
+				regulator-name = "vcc_dvdd";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_avdd: LDO_REG7 {
+				regulator-name = "vcc_avdd";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG8 {
+				regulator-name = "vccio_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: LDO_REG9 {
+				regulator-name = "vcc3v3_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_5v0: SWITCH_REG1 {
+				regulator-name = "vcc_5v0";
+			};
+
+			vcc_3v3: SWITCH_REG2 {
+				regulator-name = "vcc_3v3";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	pcf8563: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
+		clock-output-names = "xin32k";
+	};
+};
+
+&gmac {
+	assigned-clocks = <&cru CLK_GMAC_SRC_M1>, <&cru CLK_GMAC_SRC>,
+			  <&cru CLK_GMAC_TX_RX>;
+	assigned-clock-parents = <&cru CLK_GMAC_RGMII_M1>, <&cru CLK_GMAC_SRC_M1>,
+				 <&cru RMII_MODE_CLK>;
+	assigned-clock-rates = <0>, <50000000>;
+	clock_in_out = "output";
+	phy-handle = <&phy>;
+	phy-mode = "rmii";
+	phy-supply = <&vcc_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmiim1_miim &rgmiim1_rxer &rgmiim1_bus2 &rgmiim1_mclkinout>;
+	status = "okay";
+};
+
+&mdio {
+	phy: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&eth_phy_rst>;
+		reset-active-low;
+		reset-assert-us = <50000>;
+		reset-deassert-us = <10000>;
+		reset-gpios = <&gpio2 RK_PA6 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pinctrl {
+	ethernet {
+		eth_phy_rst: eth-phy-rst {
+			rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+	bt {
+		bt_enable: bt-enable {
+			rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_wake_dev: bt-wake-dev {
+			rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_wake_host: bt-wake-host {
+			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	wifi {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio0-supply = <&vcc1v8_pmu>;
+	pmuio1-supply = <&vcc3v3_sys>;
+	vccio1-supply = <&vcc_1v8>;
+	vccio2-supply = <&vccio_sd>;
+	vccio3-supply = <&vcc_1v8>;
+	vccio4-supply = <&vcc_dovdd>;
+	vccio5-supply = <&vcc_1v8>;
+	vccio6-supply = <&vcc_1v8>;
+	vccio7-supply = <&vcc_dovdd>;
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdio {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	max-frequency = <100000000>;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc1_clk &sdmmc1_cmd &sdmmc1_bus4>;
+	rockchip,default-sample-phase = <90>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_bus4 &sdmmc0_det>;
+	rockchip,default-sample-phase = <90>;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr104;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer &uart0_ctsn &uart0_rtsn>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723ds-bt";
+		device-wake-gpios = <&gpio1 RK_PC7 GPIO_ACTIVE_HIGH>; /* BT_WAKE */
+		enable-gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>; /* BT_RST */
+		host-wake-gpios = <&gpio1 RK_PC5 GPIO_ACTIVE_HIGH>; /* BT_WAKE_HOST */
+		max-speed = <2000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_enable>, <&bt_wake_dev>, <&bt_wake_host>;
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3m2_xfer>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4m2_xfer>;
+	status = "okay";
+};