| Message ID | 20231221062244.11871-1-twoerner@gmail.com (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | arm64: rockchip: dts: rk3328-rock-pi-e: enable GbE eth | expand |
Hi Trevor, Am Donnerstag, 21. Dezember 2023, 07:22:43 CET schrieb Trevor Woerner: > Adjust the device-tree to get the GbE interface working using a patch found > on the Radxa forum. > > Link: https://forum.radxa.com/t/rock-pi-e-board-version-1-21-ethhernet-not-working-in-armbian/15061/3 > Signed-off-by: Trevor Woerner <twoerner@gmail.com> > --- > @@ -165,15 +165,17 @@ mdio { > #address-cells = <1>; > #size-cells = <0>; > > - rtl8211e: ethernet-phy@1 { > + rtl8211f: ethernet-phy@1 { > + compatible = "ethernet-phy-id001c.c916", "ethernet-phy-ieee802.3-c22"; skipping through that thread, it looks like there are variants of the board with one of the rtl8211e _or_ rtl8211f phys. So while the "ethernet-phy-ieee802.3-c22" compatible would work for both, the "ethernet-phy-id001c.c916" compat effectively disables phy- probing. So applying this patch would effectively disable ethernet support on those older rock-pi-e boards? In a similar context concerning boards using different phys, it was suggested [0] that the bootloader should modify the dt it passes to the kernel to provide the correct phy id. > reg = <1>; > pinctrl-0 = <ð_phy_int_pin>, <ð_phy_reset_pin>; > pinctrl-names = "default"; > interrupt-parent = <&gpio1>; > interrupts = <24 IRQ_TYPE_LEVEL_LOW>; > - reset-assert-us = <10000>; > - reset-deassert-us = <50000>; > + reset-assert-us = <20000>; > + reset-deassert-us = <100000>; I guess for those we can consolidate onto the "slower" ones in the kernel though. > reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>; > + max-speed = <1000>; > }; > }; > }; > Heiko [0] https://lore.kernel.org/all/ecbdcfb7-32ab-45cc-991a-982c52bf4b14@gmail.com/
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts index 3cda6c627b68..41224a222048 100644 --- a/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts +++ b/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts @@ -148,7 +148,7 @@ &gmac2io { assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>; assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>; clock_in_out = "input"; - phy-handle = <&rtl8211e>; + phy-handle = <&rtl8211f>; phy-mode = "rgmii"; phy-supply = <&vcc_io>; pinctrl-names = "default"; @@ -156,8 +156,8 @@ &gmac2io { snps,aal; snps,rxpbl = <0x4>; snps,txpbl = <0x4>; - tx_delay = <0x26>; - rx_delay = <0x11>; + tx_delay = <0x1a>; + rx_delay = <0x14>; status = "okay"; mdio { @@ -165,15 +165,17 @@ mdio { #address-cells = <1>; #size-cells = <0>; - rtl8211e: ethernet-phy@1 { + rtl8211f: ethernet-phy@1 { + compatible = "ethernet-phy-id001c.c916", "ethernet-phy-ieee802.3-c22"; reg = <1>; pinctrl-0 = <ð_phy_int_pin>, <ð_phy_reset_pin>; pinctrl-names = "default"; interrupt-parent = <&gpio1>; interrupts = <24 IRQ_TYPE_LEVEL_LOW>; - reset-assert-us = <10000>; - reset-deassert-us = <50000>; + reset-assert-us = <20000>; + reset-deassert-us = <100000>; reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>; + max-speed = <1000>; }; }; };
Adjust the device-tree to get the GbE interface working using a patch found on the Radxa forum. Link: https://forum.radxa.com/t/rock-pi-e-board-version-1-21-ethhernet-not-working-in-armbian/15061/3 Signed-off-by: Trevor Woerner <twoerner@gmail.com> --- arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-)