@@ -6,6 +6,7 @@
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/rockchip.h>
#include <dt-bindings/leds/common.h>
+#include <dt-bindings/usb/pd.h>
#include "rk3588s.dtsi"
/ {
@@ -112,6 +113,18 @@ vcc5v0_sys: vcc5v0-sys-regulator {
regulator-max-microvolt = <5000000>;
};
+ vbus5v0_typec: vbus5v0-typec-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vbus5v0_typec";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio3 RK_PA4 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&vcc5v0_sys>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&typec5v_pwren>;
+ };
+
vcc_1v1_nldo_s3: vcc-1v1-nldo-s3-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc_1v1_nldo_s3";
@@ -224,6 +237,56 @@ regulator-state-mem {
&i2c2 {
status = "okay";
+ usbc0: usb-typec@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <RK_PB5 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usbc0_int>;
+ vbus-supply = <&vbus5v0_typec>;
+ status = "okay";
+
+ usb_con: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ data-role = "dual";
+ power-role = "dual";
+ try-power-role = "source";
+ op-sink-microwatt = <1000000>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_FIXED(9000, 3000, PDO_FIXED_USB_COMM)
+ PDO_FIXED(12000, 3000, PDO_FIXED_USB_COMM)>;
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ usbc0_orien_sw: endpoint {
+ remote-endpoint = <&usbdp_phy0_orientation_switch>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ usbc0_role_sw: endpoint {
+ remote-endpoint = <&dwc3_0_role_switch>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ dp_altmode_mux: endpoint {
+ remote-endpoint = <&usbdp_phy0_dp_altmode_mux>;
+ };
+ };
+ };
+ };
+ };
+
hym8563: rtc@51 {
compatible = "haoyu,hym8563";
reg = <0x51>;
@@ -256,6 +319,16 @@ vcc5v0_host_en: vcc5v0-host-en {
};
};
+ usb-typec {
+ usbc0_int: usbc0-int {
+ rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ typec5v_pwren: typec5v-pwren {
+ rockchip,pins = <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
ir-receiver {
ir_receiver_pin: ir-receiver-pin {
rockchip,pins = <1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>;
@@ -681,6 +754,14 @@ &uart9 {
status = "okay";
};
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy0_otg {
+ status = "okay";
+};
+
&u2phy2 {
status = "okay";
};
@@ -707,6 +788,43 @@ &usb_host0_ohci {
status = "okay";
};
+&usbdp_phy0 {
+ orientation-switch;
+ mode-switch;
+ sbu1-dc-gpios = <&gpio4 RK_PA0 GPIO_ACTIVE_HIGH>;
+ sbu2-dc-gpios = <&gpio4 RK_PA1 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbdp_phy0_orientation_switch: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc0_orien_sw>;
+ };
+
+ usbdp_phy0_dp_altmode_mux: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&dp_altmode_mux>;
+ };
+ };
+};
+
+&usb_host0_xhci {
+ usb-role-switch;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dwc3_0_role_switch: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc0_role_sw>;
+ };
+ };
+};
+
&usb_host1_ehci {
status = "okay";
};
Khadas Edge 2 has 2x Type-C port. One just supports PD and controlled by MCU. The other one supports PD, DP Alt mode and DRD. This commit adds support for DRD. Signed-off-by: Jacobe Zang <jacobe.zang@wesion.com> --- .../dts/rockchip/rk3588s-khadas-edge2.dts | 118 ++++++++++++++++++ 1 file changed, 118 insertions(+)